Commit Graph
847 Commits
Author SHA1 Message Date
jyvikoandClaude Opus 5.5 659bd866b3 Kernel tests: the #871 part's fitting rounds take their exact volume
rounds_that_fit_are_closed counted faces (the input's plus one per picked
edge: 38, where SMLib makes 50 with its corner faces). It now keeps
validity and no crossed loops and holds the R0.5 rounds on all 24 end-face
edges to the exact volume.

Proof. The part (plate 14 x 21.5 x 10, block 14 x 9.948 x 10 on it, the
5.2 x 7.1 window through both along x) is
14 (215 + 10 (b - a) - 36.92). At depth u into an end face's rounds the
section is that face's outline moved in by d = r - sqrt(r^2 - (r - u)^2),
each edge parallel to itself: the area less L d, L = 2 (21.5 + 20) +
2 (5.2 + 7.1) = 107.6 (the stepped outline's perimeter is its box's), plus
d^2 at each of the six convex corners (two rounds mitred), less pi d^2 / 4
at each of the six concave ones (the two shoulders and the window's four
corners: rounds meeting at a concave corner beside an unpicked sharp edge
are swept round it, the owner's ruling of 2026-10-30). The wall between
window and block side is 1.256 > 2 r, so the offsets stay apart. Over the
round the integrals of d and d^2 are r^2 (1 - pi/4) and r^3 (5/3 - pi/2),
so both ends remove
2 (L r^2 (1 - pi/4) - (6 - 6 pi/4) r^3 (5/3 - pi/2)) = 11.514718.
Graded at 1e-7 of the part's volume. It passes today (aarch64, SMLib).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:12:24 -04:00
jyvikoandClaude Opus 5.5 5af467aef0 Kernel tests: the box rounded after separate bottom rounds takes its exact volume
issue2422_vertical_after_separate_bottom_rounds compared the face count and
volume (within 0.05) of the vertical round, picked with and without its
bottom mitre, against the same round picked alone, and required every face
meshed. It now holds each of the three picks, on the 40 x 80 x 27 box and
on the same shelled 1 mm open at the top, to the exact volume; the corner
probes stay.

Proof. Horizontal sections, s up from the bottom. Below s = r the four
separate R2 bottom rounds (mitred at the corners) leave the rectangle
moved in by d = r - rho, rho = sqrt(r^2 - (r - s)^2), and where the
vertical round meets them (a sphere octant) its corner is a quarter disc of
radius rho: (L - 2d)(W - 2d) - (1 - pi/4) rho^2. Above, LW - (1 - pi/4) r^2.
With the integrals over the bottom r of rho (pi r^2 / 4), rho^2 (2 r^3 / 3),
d (r^2 (1 - pi/4)) and d^2 (r^3 (5/3 - pi/2)):
V = LW r - 2 (L + W) r^2 (1 - pi/4) + 4 r^3 (5/3 - pi/2)
  - (1 - pi/4) 2 r^3 / 3 + (H - r)(LW - (1 - pi/4) r^2) = 86174.445361;
with four such corners it is issue1557_all_vertical_corners_match_analytic
_volume's formula exactly. The shell's cavity, 38 x 78 x 26, is clear of
both rounds (along the corner's diagonal the R2 arc stays 2 - sqrt(2) in,
the cavity's corner is 1 in), so the cup is V - 77064. Graded at 1e-6.

Today SMLib's check refuses the bottom rounds' result (edge and vertex
tolerance 0.97 against 0.01), as before.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:12:24 -04:00
jyvikoandClaude Opus 5.5 a8f393ca36 Kernel tests: the tabbed plate's rim rounds take their exact volume
fillet_tabbed_plate_outer_loop_and_partial_selection_after_hole only
checked that every subset of the R25 tabbed plate's seven top-outline edges
builds and stays inside the plate. It now first holds the hole's rim round
and the three selections that end only at the plate's sharp concave
corners (the R25 arc's two halves, the tab's tangent run of sides, R2
corners and top, and both) to their exact removed volume; the sweep over
all 127 subsets stays as it was.

Proof. The outline's area A(da, dt), the arc moved in by da and the tab's
run by dt, each element parallel to itself, by Green's theorem: an arc
about c of radius rho from a to b gives
1/2 (rho^2 (b - a) + rho (cx (sin b - sin a) - cy (cos b - cos a))), a
segment p -> q gives 1/2 p x q. At a concave corner (+-4, sqrt(609)) where
only one side moves, the elements meet where they cross (the round runs
into the other wall: the section is the union of the two sides' half
regions); where both move the corner is swept, an arc of radius d about the
corner, traversed clockwise from the arc's normal to the side's (the
owner's ruling of 2026-10-30 for rounds meeting at a concave corner beside
an unpicked sharp edge: the profile swept round the corner edge). Checks:
A(0, 0) = 312.5 (pi + 2 theta) + 4 y + 8 (cy - y) + 8 + 2 pi (disc sector,
triangle, tab, R2 corners), and A(0, 0) - A(d, d) = L d - pi d^2 by the
Steiner formula for the swept offset (total smooth turning 2 pi + 2 theta,
the two swept corners -theta each), agreeing to 1e-15 at d = 0.1, 0.3,
0.5; A(0, 0) - A(0, d) agrees with a 0.004 mm grid to 2e-6. The round's
section at height r sin(phi) into it is the outline moved in by
d = r (1 - cos phi), so it removes the integral of
(A(0, 0) - A(d)) r cos(phi) dphi over [0, pi/2] (midpoint rule, 8192
steps, converged to 1e-7 against 4096). The hole's rim round is Pappus:
(1 - pi/4) r^2 about the axis at 1.5 + r (10 - 3 pi) / (3 (4 - pi)).
Graded at 1e-5 of the removal, the bound the D prism's rounds are held to
(the blend surfaces are SMLib's fits).

Today the three selections build with these volumes (aarch64, SMLib); the
sweep still fails where a subset ends a round at a tangent joint (the x = 4
side without its R2 corner): SMLib cannot end a blend inside a tangent
chain, "the blend cannot end there".

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:12:24 -04:00
jyvikoandClaude Opus 5.5 3569298a40 Kernel tests: a chamfer whose leg runs off the thin rim is refused, naming the largest
The owner's blend-overflow ruling of 2026-10-30: a chamfer whose leg runs
off the face beside its edge over another face is refused as too large,
naming the largest size that fits (a 2 mm chamfer on the basin's 1 mm rim
would lower the slab's front face from 30 to 29.382); a full-width chamfer
stays refused. Two tests wanted those chamfers built and cut from the slab:

- chamfer_wider_than_sloped_basin_rim_is_cut_and_a_full_width_one_refused
  becomes chamfer_wider_than_sloped_basin_rim_is_refused_naming_the_largest:
  (margin, d) = (1, 2), (1, 3), (0.5, 4) and the full widths (0.5, 0.5),
  (1, 1) are TooLarge, the body unchanged, and the message names a largest
  size just below the rim's width: the full width is refused, so the fit
  search (three significant digits of the size asked, step
  10^(floor(log10 d) - 3)) ends one step below it, in
  [margin - step, margin). The removal formula for the cut chamfer
  (basin_rim_chamfer_removed) has no use left and goes.
- equal_slope_rim_loops_stay_inside_the_material: the 2 mm chamfer of the
  1 mm rim's loop is refused the same way (largest in [0.999, 1)); the R4
  round (tangent side, builds) and the 0.5 blends stay.

The half-width chamfer on each rim, which only had to take something off,
now takes its exact volume. As in chamfer_sloped_basin_rim: the triangle
with legs d on the top and d down the wall towards (20, 10) (run
20 - margin over the 20 drop) has area d * drop / 2 with
drop = 20 d / sqrt((20 - margin)^2 + 400), and the chamfer's length at
depth h is 60 - h between the end walls x = 20 + (30 - z) / 2 (planar:
x depends on z only), so it removes d * drop / 2 * (60 - drop / 3);
graded at 1e-8 as that test is.

Today SMLib refuses the chamfers as too large, but the message does not
name the largest that fits yet ("the chamfer is larger than the faces
beside its edges allow"), the SolidCraft change issue_1080's R30 test
waits for too.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:12:24 -04:00
jyvikoandClaude Opus 5.5 65e46a9628 Kernel tests: a round as tall as its wall and more builds on the disc
The owner's blend-overflow ruling of 2026-10-30: a round that runs past
its face on its tangent side is built on the face continued and cut from
the part, keeping its radius. loop_fillet_as_tall_as_its_wall_consumes_it
still wanted R2.001 and R2.5 on the R13 x 2 disc refused as taller than the
wall; they now must build, valid, with the exact volume.

Proof. The round's section in (rho, z) is the r square at the top edge
outside the circle about (13 - r, 2 - r), clipped to z >= 0. With
t = z - (2 - r) = r sin(theta), the round's inner radius is
rho(theta) = 13 - r + r cos(theta), theta from asin((r - 2) / r) to pi/2,
and the disc keeps pi (169 * 2 - integral (169 - rho^2) dz), dz =
r cos(theta) dtheta (midpoint rule, 20000 steps). At r = 2 it is Pappus,
2 pi 169 - (1 - pi/4) 4 * 2 pi (13 - c), c = 2 (10 - 3 pi) / (3 (4 - pi))
(checked to 1e-9 in the test); at r = 2.5 it is 957.692239 mm3, the
ruling's number, the same integral as
rounds_past_the_bottom_of_a_wall_are_cut_from_the_part's. Graded at 1e-6
as that test is.

Today SMLib fails the R2.001 round (status 1001): a convex round past its
face is not yet built by subtraction, the cause fillets/KNOWN_FAILING gives
4782 and 5158.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:12:24 -04:00
jyvikoandClaude Opus 5.5 e9963439b1 Kernel tests: the round into a hole moves to the rig, with the hole cut the test's way
a_round_into_a_hole_is_cut_by_it (issue_324_tests.rs) built rig case
fillets/324-fillet-over-hole-overlap's body, but cut its hole with a cylinder
longer than the block (z -1 to 11) where the rig extrudes a sketch circle
flush. The new case fillets/324-fillet-over-hole-cut-by-overlong-cylinder
builds it that way (solid.cylinder, base z -1, height 12, cut) and holds it to
the same hand-derived answer: block 40x20x10 less the r3 hole at (20, 14.5)
(282.74) less the R4 round on the top edge at y = 20, 40 (16 - 4 pi) = 137.35,
plus what both remove, the integral over y in [16, 17.5] of
(4 - sqrt(16 - (y - 16)^2)) * 2 sqrt(9 - (y - 14.5)^2) = 0.375830 (re-derived
with the substitution y = 17.5 - s^2, 200000 steps):
V = 8000 - 90 pi - 40 (16 - 4 pi) + 0.375830 = 7580.287315, and G1 on the
blend. It passes today (aarch64, SMLib), as the flush case does, so it needs no
KNOWN_FAILING line; the unit test, a duplicate of the two cases, is dropped.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:12:24 -04:00
jyvikoandClaude Opus 5.5 51641123cf Kernel tests: drop the mixed arc-and-line mitre test, the rig's 485 grades it
fillet_mixed_arc_and_line_joint_preserves_both_section_radii put R0.5 on the
D prism's top outline and checked 258 points of each mitre edge against the
cylinder and torus to 1e-7 in r squared, through the record's edges. The rig's
fillets/485-fillet-d-prism-top-outline-arc-and-flat builds the same prism with
the same radius and grades the removed volume to 5e-5 (a 0.12 mm3 loss shows)
and G1 on every blend seam, which is what the mitre's accuracy is for.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:12:24 -04:00
jyvikoandClaude Opus 5.5 b66821c829 Kernel tests: the third round at a mitred corner takes its tangent chain, a sphere octant
Stale since 84bd2daad (the Fillet feature rounds each pick's tangent chain). After a and b are
rounded at 2 mm and meet in a mitre, the mitre's seam leaves c's end along c, so c's chain is c
and the seam; rounded at 2 mm, as the issue1557 tests pick, the corner is a sphere octant.

Proof: the 20 mm cube less its three rounds, each (1 − π/4) r² over its 18 mm straight part, and
the corner's 2 mm cube less the octant, r³ (1 − π/6): 8000 − 3·(1 − π/4)·4·18 − 8·(1 − π/6) =
7949.834793498635. Measured 7949.834793513291 (1.8e-12 relative), 10 faces, valid; the check is
tightened from 0.05 mm³ to 1e-11 relative.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:07:27 -04:00
jyvikoandClaude Opus 5.5 96b248d288 Kernel tests: a slot narrower than the taper closes partway up and builds; a closing hole is refused
tangency-labs/smlib#64 builds a tapered wall that closes partway up (its neighbours meet above
its apex), so the 0.2 mm slot of a 10 mm square tapered 10° out over 2 mm now builds where it
was refused. The test, renamed for what it checks, asserts the slot's solid is valid with its
exact volume and keeps the ring's refusal (its 0.3 mm hole closes entirely).

Proof of the volume, t = tan 10°: every wall moves out of the material by z·t at height z. The
square grows to 10 + 2zt, so without the slot ∫₀² (10 + 2zt)² dz = ((10 + 4t)³ − 1000)/(6t).
The slot narrows to 0.2 − 2zt and keeps its length 8 (its end wall and the square's side both
move up by zt); it closes at z = 0.1/t = 0.567 and takes ∫ 8 (0.2 − 2zt) dz over 0..0.1/t =
0.08/t. Volume ((10 + 4t)³ − 1000)/(6t) − 0.08/t = 213.984095421783; measured to 1e-6.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:07:27 -04:00
jyvikoandClaude Opus 5.5 2e123eb3dc Kernel tests: a swallowed tip's volume is the drafted wedge's, every wall at the taper
tapered_extrude_swallows_a_short_tip expected the prismatoid whose two tip
corners run straight to the top's tip (h/6 (A0 + 4 A_mid + A1)), the solid
the old offset-and-rule construction built: its tip triangle leans about 40
degrees, not the 5 degree taper. With every wall drafted 5 degrees the tip's
wall is a triangle that closes where the long sides meet across it, at
z* = 0.126237833 (offset 0.011044379), and above that the long sides meet
along a ridge. The section at height z is the profile's lines moved in by
z tan(a): a quadrilateral below z*, a triangle above, each area quadratic in
z, so Simpson's rule on each piece is exact: V = 72.883284979193. The old
value, 72.882657253174, is 8.6e-6 off, past the test's 1e-6. SMLib's
DRAFT_CORNER_ROUND path builds exactly this solid (72.883284979193, 6 faces);
the default curvature rule still refuses it (SMLIB_ERR_WALL_CLOSES at
(20, -0.01, 0)), so the test fails until the fork builds a wall that closes
partway up.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:07:27 -04:00
jyvikoandClaude Opus 5.5 1817cffaf3 Shell: a basin shelled past its 4 mm rim measures its exact sharp offset
shell_thicker_than_a_rim_is_refused expected the "rim or ledge" refusal from 9508ee749,
added because truck's face offset turned the top face inside out and returned a body of
about twice the volume. SMLib builds the exact sharp-edged offset, and its volumes are the
closed form, so the test now checks those (renamed
shell_of_a_basin_past_its_rim_keeps_the_rim_solid).

Proof. Slab [0,100]×[0,60]×[0,30]; pocket lofted from x 20..80, y 4..50 at z 30 to
x 30..70, y 20..40 at z 10, its sides the planes x + z/2 = 35, x − z/2 = 65,
y + 0.8z = 28, y − z/2 = 35 (normal lengths √5/2, √5/2, √1.64, √5/2). Shelled open at
z = 0 by t, the cavity is the slab shrunk by t (x t..100−t, y t..60−t, z 0..30−t) less the
pocket grown by t (each plane moved out by t·|n|, floor z = 10 − t). For t ≤ 6 the grown
pocket stays inside the shrunk slab in x and at the back (50 + 0.618t ≤ 60 − t); its front
reaches y = t at z0 = (28 − (1 + √1.64)t)/0.8, below 30 − t from t ≈ 2.70 (the rim stays
solid above z0). With W = 30 + z + √5 t,
  grown(t) = ∫[10−t, z0] W (7 + 1.3z + (√5/2 + √1.64)t) dz + ∫[z0, 30−t] W (35 + z/2 + (√5/2 − 1)t) dz,
  V(t) = 180000 − grown(0) − (100 − 2t)(60 − 2t)(30 − t) + grown(t),
grown(0) = 33866.667, so V(1) = 17105.6240415, V(4) = 63560.2492284,
V(6) = 90113.9202101. SMLib measures 17105.6242, 63560.2492, 90113.9203 (≤ 1e-8
relative). The test computes the closed form and checks each shell to 1e-6, with the
centroid inside its box and on x = 50 as before.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 05:56:11 -04:00
jyvikoandClaude Opus 5.5 f37b954988 Native B-rep: a body is written as it serializes, not through a JSON value
encode_native_body turned the whole saved record into a serde_json
Value (a map with an owned key for every field of every face, edge,
curve and pcurve), checked it, counted it, then wrote it out. Building
that tree was most of the cost: on the Menger level 4 sponge (3 tools,
--save) the 101 bodies the model cache encodes, 535 MB of encodings,
took 24.1 s of encode_native_body, 20.8 s of it in to_value.

binary::write_serialized is a serde Serializer for the tagged binary
format: it writes each value as it is serialized and applies the same
checks as it goes (nesting, string and array budgets, floats within
1e12, the value budget, the size limit). An object's entries are put in
key order when it closes, as the JSON map held them; floats that are not
finite are null, as to_value made them. The bytes are the same: a test
encodes plain, blended, cut, extruded, painted, split, open, round and
far-placed bodies both ways and compares them, and all 101 Menger bodies
(6 to 28 412 faces, 15 kB to 68 MB) encoded both ways in one run were
byte for byte the same. The JSON-value writer stays for the tests that
build hostile records.

Menger L4 3-tool --save, two runs each: encode_native_body 24.1 / 25.3 s
before, 3.0 / 3.0 s after (the longest call 1.34 s -> 0.29 s); the run
41.2 / 41.4 s wall before, 39.1 / 39.2 s after (the encodings run on
16 threads).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 05:55:40 -04:00
jyvikoandClaude Opus 5.5 918429c6dc Sheet machining: a trimmed To Object tool is measured as the prism its record proves
A To Object extrude to a curved face runs its tool through the target and
cuts the target out of it. The SMLib boolean carries no extrusion face
sources (they stood for the untrimmed profile), so sheet_tool_span, which
read the tool's depth and footprint only off its extrusion caps, gave up
and the intersect was refused as unrepresentable.

The tool's current geometry says what it is: the kernel's prism
certificate (prism_measure, the one component copies are compared by)
reads off the exact record whether a body is a uniform prism along a
direction, its two cap levels and its section of lines and arcs. It is
now public as certified_prism_section, and sheet_tool_span uses it when
the caps don't certify the tool: the levels are the depth, the section the
footprint the To Object cut is bounded by. A tool trimmed to something
that is not a prism (a curved roof over it) is still refused.

partial_depth_intersect_curved_to_object_preserves_current_trimmed_cap_footprint
passes: the tool is the square 20 ... 30 less the pin's circle (radius 2),
z 0 ... 1, 100 - 4π, as the test's own witness extrude measures it. A
kernel test reads that section off the trimmed lump.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 05:55:40 -04:00
jyvikoandClaude Opus 5.5 74001e5325 Tests: check what each operation is for, not how many faces it makes
The kernel switch broke these tests only through their counts, which record how a kernel splits
faces rather than whether the result is right. Each now checks its intent:
- a fitted circle is the exact circle (centre, radius, a full turn), not "one segment";
- the tight bend sweeps a valid solid of Pappus' volume, πr²(40 + 5π/2), not a count of faces,
  edges and vertices;
- the Pi case keeps each outer side one face, stays valid after every feature and rebuilds the
  same topology at 32 whether built there or edited there, without a hard-coded table of totals;
- a certified paint stays on the wall's radius and covers as many faces after an edit, a copy
  and reopening as when it was painted;
- the offset sleeve and the extended strip are checked by their exact areas only.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 04:32:50 -04:00
jyvikoandClaude Opus 5.5 0c4f54edf3 rustfmt
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 04:32:50 -04:00
jyvikoandClaude Opus 5.5 add3ebdb03 Kernel: the box-and-fillet wire records are SMLib's
box_and_fillet_have_stable_wire_records compared the encoding of a box and a filleted box
with records truck built (2f4d6acac). Since f11c0c571 an operation's result is the record
SMLib gives, which numbers the box's faces in its own order and the fillet's edges by its
history, so the golden differed in face order, face sources and edge history, not in the
encoding. Rewritten with NATIVE_BREP_BLESS=1 and checked against the geometry: the box 6
planes, 12 edges, 8 vertices, each face source's plane its face's; the filleted box 7 faces,
15 edges, 10 vertices (one edge replaced by a face: +1, +3, +2), the round a cylinder of radius
2 along x on the axis (y, z) = (2, 8), 2 from y = 0 and z = 10.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 04:32:50 -04:00
jyvikoandClaude Opus 5.5 1bc8b204f1 Kernel tests: a circle is one closed arc, a round wall one face
Since 09c979a4b a full circle in a profile is one arc of a whole turn, so what is built from
it is one closed edge and one wall closed along its seam. Five kernel tests still expected
truck's halves:
- a_small_hole_in_a_large_spline_face_cuts_cleanly: the Ø1 hole adds one face (its wall),
  not two; the removed volume (π · 0.25 · 40) is unchanged.
- fit_loop (two mesh_convert tests): a fitted circle is Loop2::circle, one segment.
- tight_bend_counts: a Ø10 tube swept up 20, round a quarter turn of radius 5, along 20. The
  circle starts at (5, 0), which runs up to (5, 0, 20) on the bend's axis, where the turn
  leaves it: the bend face has no seam and both straights' seams end there. By the ladder's
  rule (each whole curve once, each seam): 5 faces (2 caps, one per path segment), 6 edges
  (4 circles, 2 seams), 3 vertices (the seams' ends: (5,0,0), (5,0,20), (25,0,20)), the
  record's own counts.
- extruded_circles_go_as_cylinders: the record holds the wall as the cylinder it is (one
  face of three), no longer a rational spline; it still goes into SMLib as its cylinder.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 04:32:50 -04:00
jyvikoandClaude Opus 5.5 ec4eebaa82 sew: a folded pcurve has no piece shorter than it lifts onto its edge
A folded edge's Hermite pcurve on a bend's form breaks where the edge's angle crosses a
quarter. At the 120 degree corner with flanges at 60 and 90 degrees under a tear, an edge
starts 3.25e-12 of its parameter short of a quarter: the crossing was kept as a break
(breaks within 1e-12 of the parameter merged), the pieces halved to 1.6e-12, and SMLib,
given knots 1.6e-12 apart, handed the pcurve back with 15 equal knots at degree 7 ("SMLib
export: pcurve: loop 0 use 1: given pcurve: portable B-rep: knot multiplicity"). A crossing
whose point on the edge lies within the pcurve's lift accuracy (FOLD_TOL of the edge's size)
of the previous break is that break; the end is never merged into the start.

Fixes sheet::tests::every_pair_of_angles_is_torn_or_keeps_its_notch (torn pairs 37, 37, 27).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:20:47 -04:00
jyvikoandClaude Opus 5.5 48d72ba2be Convert Mesh: a triangle of no area is dropped, not refused (#4561)
A triangle whose corners lie on one line (or weld into one another) adds no
surface, so welding now drops it, with any corner only it used, instead of
refusing the whole mesh as having a degenerate triangle. The closed and
consistently oriented check that follows still refuses a mesh that needed it to
close, and a mesh of nothing but such triangles is refused by name. Dropping its
unused corners keeps a dropped triangle from widening the part's extent, which
the prism search reads from every position.

Regression test a_zero_area_triangle_is_dropped: the 20 x 10 x 5 box with the
case's extra triangle (0,0,0) (10,0,0) (20,0,0) converts to six faces and
V = 1000 mm^3.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:18:03 -04:00
jyvikoandClaude Opus 5.5 191c1b8551 Fair: a net of up to 128 x 128 control points, the band bounding the solver
SMLib's thickening of the test sheet makes a top face of 72 x 78 control points,
which the 4096-point cap refused (TooLarge) before the solver saw it. The band
cap (2^21 entries, 16 MB) is what bounds the system's memory and its
factorisation (at most n min(n, bw)^2 work); the 72 x 78 bicubic net needs
5320 unknowns 213 apart, 1.14 M entries, well within it. The point cap now
bounds only the per-step energy sweep and the net's copies: 2^14 points, above
the band's own limit for square bicubic nets (about 90 x 90), so a face is
refused for the system it needs rather than its size. The hostile-input test
asks for 129 x 129 and checks the refusal is TooLarge.

a_body_face_is_faired_with_its_edges_untouched_and_its_history_kept passes.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:18:03 -04:00
jyvikoandClaude Opus 5.5 1a02890118 Planar region tests: edges on one line are one edge of the result
Two tests counted the old 2D boolean's edges, which kept a vertex wherever an operand's corner
or edge end lay on another's edge. SMLib's planar boolean leaves no vertex that is no corner:
edges on one line within the tolerance are one edge. The results are the same regions with
fewer, whole edges, and each test's point stands (no edge shorter than the tolerance, no sliver):
- a quadrilateral cut away from below a square whose bottom edge it lies on within 1e-8 (tilted
  1e-9 rad) leaves the square's four 10 mm edges (its corner at x = 4 is within 1e-8 of that
  edge's line), and its union runs along y = 0 as one 14 mm edge (the quadrilateral's bottom
  edge is within 1e-8 of y = 0 all along): [4, 5, 5, 10, 10, 14];
- the bent plate and the strip under it: their ends on the line x = 150 are one edge from
  y = 47 to 80, six edges for every turn and offset tried, the shortest 3.

Fixes prism::planar_tests::overlapping_lines_a_hair_from_parallel_do_not_cross and
a_bent_edge_crossing_its_neighbour_by_their_corner_leaves_no_sliver.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:59 -04:00
jyvikoandClaude Opus 5.5 64188ce435 Planar regions: a hole goes to the material that holds it, read closer than the hole lies
Reading a planar sheet's faces back as regions, each hole went to the smallest outline whose
Loop2::contains held its middle: even-odd against the outline's polyline within 1e-3 mm. A
5e-5 mm square cut 1.7e-4 mm inside a radius-10 circle lies outside the polyline's chords there,
so no outline held it and the cut failed ("face 0 has a hole outside its material"). An
outline now holds a point by its polyline within a quarter of the point's distance from it (its
nearest point on the exact segments), which no chord can pass the point by.

Fixes kernel prism::planar_tests::tiny_tool_between_circle_and_display_chord_is_not_lost.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:59 -04:00
jyvikoandClaude Opus 5.5 f8b45f2772 STEP import: a void reads as a cavity whichever way its shell flag points, again
94bd8719a (#3730) turned a BREP_WITH_VOIDS void inside out when it enclosed volume of the
outer shell's sign: SOLIDWORKS writes .F. over a void shell already facing into its cavity,
SolidCraft .T. That lived in the truck reader; the schema-4 reader (crates/step) that replaced
it took the flag alone, and the block with a 20 x 6 x 5 cavity read as 15600 (the cavity added)
instead of 15000 - 600 = 14400.

The reader now takes each void's sign from the faces themselves before it orders the record:
the divergence theorem on the record's surfaces and pcurves (sew's face_flux of p / 3, moved
to geom's brep::eval so both use it). A void enclosing volume of the outer shell's sign has its
faces turned over. Flipping on the finished record is not an option: its edges are ordered by
the faces' sides.

Fixes kernel step_in::tests::a_void_reads_as_a_cavity_whichever_way_its_shell_flag_points.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:59 -04:00
jyvikoandClaude Opus 5.5 e5476706b1 Issue 616 test: the lid's volume is its closed form, 6703.5344
The expected 6703.5222 was a mesh measure (truck). The lid exactly: the 76.8 x 89.3 x 2.4
plate less its four 3 mm corner rounds ((76.8 * 89.3 - 36 (1 - pi/4)) * 2.4 = 16441.2344), the
skirt ring ((71.5 * 84 - 68.5 * 81) * 3 = 1372.5), less the window (68 * 61 * 2.4 = 9955.2) and
the slot (44 * 10 * 2.4 = 1056) through the plate, and the notch through the skirt's 1.5 mm wall
(22 * 1.5 * 3 = 99): 6703.534401. The window and slot lie inside the ring's opening and the
notch above the plate, so nothing else overlaps. SMLib measures 6703.534401575, 2.6e-7 off.
The test now computes that closed form and holds the body to 1e-6.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:59 -04:00
jyvikoandClaude Opus 5.5 a100c7c063 Loft rails: a station grows about its section's centroid by length, not the mean of its control points
A whole circle is now one closed rational curve (Loop2::circle is one segment), whose first
control point is repeated as its last: the mean of its nine control points sat r/9 towards the
seam, and a rail scaled each station about that point. A rail bulging from radius 10 to 15
(r = 10 + 5 sin(pi z/40)) then grew the circles as if r = 10 + 5.625 sin, volume
4632.8 pi + 9000 = 23553.9 against the solid of revolution's pi * integral r^2 dz =
4500 pi + 8000 = 22137.2 (+6.4%; the engine's arc rail +6.5%).

The middle is now the curves' centroid by length, integral x ds / integral ds (8-point
Gauss-Legendre per knot span on the rational point's speed): the shape's alone, however its
curves are written; a circle's is its centre. geom's GAUSS_8 is public for it.

Fixes kernel loft_rails_tests::a_bulging_rail_makes_the_solid_of_revolution_of_the_rail and
engine loft_rails_tests::a_rail_turns_a_loft_into_its_solid_of_revolution_and_stretching_is_an_edit.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:59 -04:00
jyvikoandClaude Opus 5.5 c47c1d26a6 Tests: the fit and taper tests use geometry that still doesn't fit
Under the blend-overflow decision (237f0ae74) a convex round running over a face's far
edge (a cliff) is built and cut from the part, so the truck-era fixtures of the reduce
and taper fits (a 2 mm fin, a plate narrowing to 2 mm, a wedge, a 10 mm cube's edge at
R20) no longer refuse their radius and the fits have nothing to react to. Each test now
uses a case SMLib still refuses, and checks the cliff case builds:

- engine fillet_fit_reduce_keeps_the_radius_where_it_fits: a 14 x 6 x 10 post on a
  40 x 30 x 20 block, its four verticals at 3.5 (two rounds would cross on its 6 mm ends)
  reduced to 3 on 4 of 5 edges, the block's corner kept at 3.5: 24840 - (4 - pi) 90 -
  (1 - pi/4) 3.5^2 20. New fillet_fit_reduce_keeps_a_round_over_a_cliff: the fin's R4
  builds, nothing reduced, at the kernel's fillet_max_each answer.
- engine fillet_fit_taper_follows_the_room_along_the_edge, spline_fillet_takes_over_a_taper,
  kernel taper_follows_the_room_along_the_edge, ui-egui fillet_spline_handle_tests: the
  narrowing plate stands against a wall behind its slanted side (z -15 to 30), so its top
  and bottom end in concave edges: R3 is refused and tapers 3 -> 1.8 as before. Without
  the wall, R3 is cut over the 2 mm top's far edge and kept constant: at x the section
  loses (1 - pi/4) 9, or 3 w - (F(3) - F(3 - w)) where the top is w < 3 wide, 6522.7745566.
- The wedge closing to a point: on its own R16 is cut over its cliffs (the section
  integral, 4195.578821, SMLib within 4e-8) and kept; its room's taper is checked as a
  spline fillet. Against a wall (new fillet_fit_taper_closes_to_a_point) the taper must
  close to 0, which SMLib fails today (status 1001).
- kernel taper_mesh_tests: the collapsed taper is built from taper() as a spline fillet.
- ui-egui the_feature_menu_copies_a_warning_message: the 10 mm cube's four verticals at
  6 are reduced to 5 (a full round), which the warning says.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:55 -04:00
jyvikoandClaude Opus 5.5 deaf8e6793 Tests: convex blends past a cliff are cut from the part, as the owner decided
The owner's blend-overflow decision (2026-10-25, 237f0ae74): a convex round or chamfer
whose rail runs off its face across a cliff (an opening's rim, a hole, the part's
outline) is built on the faces continued and what it removes is subtracted, so it never
bridges an opening; a round may use up a face; a chamfer of a face's full width stays
refused. These tests still expected truck's refusals. Each now expects the decision's
body, with its answer from the geometry:

- issue_1080 chamfer_into_a_pocket_is_cut_by_it (was ..._is_refused_with_the_size_that_fits):
  chamfer 6 into the pocket 4 mm in removes 360 - 20 (its triangle less the part over
  the pocket): 14660; 6 along the top and 2 down, 120 - 20/3; 2 and 6, 120.
- issue_1080 fillet_into_a_pocket_is_cut_by_it_and_one_that_fits_builds: R5 removes
  (1 - pi/4) 25 along 20 less 10 (5 - (sqrt(24)/2 + 12.5 asin(1/5))): 14893.0344442.
- issue_1080 chamfers_crossing_each_other_are_refused: still refused (they cross);
  chamfer_max and fillet_max find 2 mm.
- issue_1080 rounds_on_both_sides_of_a_wall_build_as_one_fillet: R7 alone opens a slit
  where its arc passes the inside corner: V0 - (104 (1 - pi/4) 49 - 100 a), a = the square
  [25, 30] x [35, 40] outside the circle about (25, 35), 5 (5 - sqrt 24) - (F(5) - F(sqrt 24)):
  38458.8958265. Both at R7: the arcs about (25, 35) and (23, 33) cross only outside both
  quarter arcs and the inner round's material holds the slit, so V0 - 4 (1 - pi/4) 49 =
  39509.9380404 (was expected refused).
- issue_324 a_round_into_a_hole_is_cut_by_it (was the_radius_offered_beside_a_hole_fits):
  R4 over the r3 hole: 8000 - 90 pi - (640 (1 - pi/4) - the round's height over the
  hole's width, integrated with y = 17.5 - s^2): 7580.2873154.
- issue_851 arc_top_blend_uses_up_the_wall_and_refuses_a_collapsed_one: a round of the
  wall's full height uses the wall up (one face for the wall, the removal integrated as for
  the other sizes); the full-height chamfer stays refused.
- kernel tests: fillet_max_finds_the_largest_radius_that_works keeps the post (3.5 -> 3)
  and the no-edge case; its disc and notch cases move to
  rounds_past_the_bottom_of_a_wall_are_cut_from_the_part: the 2 mm disc's R2.5 turned
  section, pi (338 - integral of (169 - rho^2) dz), rho = 10.5 + 2.5 cos(theta) (the same
  formula gives SMLib's R2 994.15188 exactly), 957.6922389; the notched block's outline
  R7, 11925 - (1 - pi/4) r^2 (140 - 8 c), c = r (10 - 3 pi) / (3 (4 - pi)) (SMLib's R7 within
  5e-8), and R8 less its part over the notch, integral of 2 (5 g - g^2/2), g = 8 - sqrt(64 - t^2).
- kernel tests: chamfer_wider_than_sloped_basin_rim_is_cut_and_a_full_width_one_refused:
  past the 1 mm and 0.5 mm rims the chamfer runs over the slab's front edge and is cut:
  the clipped triangle's area (30 + z centroid), its length 60 - h between the sloped end
  walls (the same formula gives chamfer_sloped_basin_rim's fitting chamfer to 1e-12);
  a chamfer as wide as the rim is refused.
- blend_corner sloped_rim_fillets_stay_inside_the_material, equal_slope_rim_loops_stay_
  inside_the_material: R4 and chamfer 2 over the thin rim build, every vertex inside the slab.
- engine blend_fit chamfer_through_the_openings_is_cut_by_them: the report's 9 mm chamfer
  is cut by the openings, 3350 (the rig's fillets/1080 case).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:55 -04:00
jyvikoandClaude Opus 5.5 8bcd81244b Tests: a blend refused as too large is SMLib's NO_ROOM, in its own words
Since bcbb99005 a blend larger than its faces is SMLib's refusal (KernelError::TooLarge,
"the fillet is larger than the faces beside its edges allow"); truck's room check, whose
words these tests still matched, went with blend_fit. The refusals themselves stand:

- fillet_consuming_a_side_face_makes_a_full_round: R3.001 and R3.5 on the 14 x 6 x 10
  box's four vertical edges, past the full round, are refused as too large (no longer
  "larger than the neighbouring faces"); the body unchanged is its own volume before
  (SMLib's measure of the box is 839.9999999999998, not 840 bit for bit).
- a_chamfer_that_would_grow_the_part_on_a_convex_edge_is_refused: refused as too large;
  the word "convex" was the old check's.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:55 -04:00
jyvikoandClaude Opus 5.5 d945cf53a0 Fillet and chamfer: a refusal as too large names the largest size that fits
When the kernel's room pre-check went (bcbb99005), a fillet or chamfer refused as
too large stopped saying what would fit: only SMLib's NO_ROOM words were left. The
rig expects the refusal to name it (fillets/4782-fillet-two-end-verticals-past-a-full-round:
"the largest radius that fits is 7.5 mm", fillet_max for the exact fit).

A constant fillet with the exact fit, and an equal-distance chamfer, refused as too
large now add "; the largest radius (distance) that fits is X mm", found by the same
bisection fillet_max runs (up to 16 blends, three significant digits), now shared with
a new kernel::chamfer_max. Where the search itself fails (a candidate failing for
another reason), the refusal is left as it was. The reduce and taper fits and the
kernel's own searches call the kernel blends directly and do not pay for it.

Tests: the 14 x 6 x 10 post's R3.5 names 3 mm; a 4 mm rib's crossing chamfers and
rounds at 3 name 2 mm.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:55 -04:00
jyvikoandClaude Opus 5.5 44b7793642 Tests: a point path's sweep has a wall along each line; coplanar walls join at a corner
sweeps_along_paths expected one wall for the circle swept through 41 points of
a smooth curve: a point path is the polyline its points make, swept line by
line and mitred at each point since 43e8b0349 (sweep_path's own test expects
40 + 2 faces since d9274aaf1), so the circle's one segment has a wall along
each of the 40 lines.

The holed square along the L-shaped path expected two faces per segment. The
corner turns the profile about Y, so each line at a constant y (the outer
loop's segments 0 and 2, the hole's 1 and 3) sweeps the plane y = c it lies in
along both legs, and the two walls meet edge to edge on the mitre in that one
plane: one L-shaped planar face. The lines at a constant x sweep two planes,
two faces. check_sweep takes the count per segment.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:51 -04:00
jyvikoandClaude Opus 5.5 1e4b644028 Provenance: a sweep's origins are the ones it recorded
sweep_origins read a sweep_path tool's faces by the truck face order (walls in
profile order, then the start and end caps), and fell back to swept_origins,
which names a face without an edge in the profile's plane an end cap. SMLib's
sweep along lines and arcs is made piece by piece and mitred at each corner
(tangency-labs/smlib#43), so most walls start further along the path: 39 of a
44-face sweep came out as end caps (105 of 110 before the previous commit). The
sweep records each face's origin as it builds it (Body::history), and
sweep_origins now returns those, finding by geometry only a face the tool names
no origin for. swept_origins says what it holds for.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:51 -04:00
jyvikoandClaude Opus 5.5 1ee5f1af30 Kernel: a mitred sweep carries a slanted section all the way to each mitre
A sweep along a path with corners sweeps each run past its corners and cuts it
back to the plane halving the corner. The lead past the corner was the
profile's reach times tan(turn / 2), enough only for a profile square to the
path. A point standing s ahead of the path and w from it needs
w tan(turn / 2) - s past a corner (w tan(turn / 2) + s before one): a profile
at a slant to its path reaches across the mitre by its slant as well, and a run
carried short of it leaves a notch with a piece of the run's section in it.
The section keeps both distances along a run and through each corner (it
turns with the path; a twist keeps them, an end scale grows them by at most
its largest scale), so the lead is taken from the profile's points at the
start, for the plain and the controlled sweep. A profile square to the path
(s = 0) leads exactly as before.

The walls' history seeds sat at the middle section of each run, which for a
slanted profile on a run shorter than its slant lies past the mitres, on the
next run's wall: half the walls came out generated. Each piece's seed now sits
half way along the stretch its own point keeps between the mitres, carried
there exactly along lines and arcs (as SMLib's sweep turning with the path
carries the profile), at the station there in the controlled sweep.

A flat 4 mm square swept along 21 points of a rising sine (provenance test):
110 faces, 66 of them notch faces, and walls left unnamed; now 44 (two caps, the two
walls in the path's plane, a wall of each slanted side along each line), volume
16 cos(slant) L to 1e-6 (new test a_slanted_profile_meets_itself_at_every_mitre).
The square round a closed 122-line polyline (issue_2005
closed_polyline_sweep_shares_its_starting_section): the first section leaned
by half a chord's turn left a 6.2 mm^2 piece of it at the closing mitre, named
the start cap; now 246 faces, every one a wall.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:51 -04:00
jyvikoandClaude Opus 5.5 b9d0a33080 Mesh memo test: SMLib's booleans mesh neither operand
The test cut three regions from a plate that keeps its meshes and
expected the memo to hold one mesh afterwards: the old kernel's booleans
meshed their operands. On SMLib (ops::boolean -> smlib_boolean, since
42c41464a) a boolean reads the exact record and a tool apart from the
body is found from the exact boxes, so no boolean meshes anything and the
memo is empty after them. The test now asserts that, then that meshing
the kept body twice at one tolerance makes one memo entry, bit-equal to a
fresh mesh, which is the reuse the memo is for.

Fixes kernel body::mesh_memo_tests::regions_cut_from_a_body_keeping_its_meshes_are_unchanged.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:46 -04:00
jyvikoandClaude Opus 5.5 e1b762c4bd Booleans and Shell keep the lines faces were split along on purpose
Split Face records its lines on the body (split_lines): heal and the
certified-planar regularizer keep the faces apart along them, and they
make the body regularization-protected. On SMLib the boolean, the n-way
union and Shell carried the protection over but dropped the lines, so a
body with an authored split lost its record after a Union with partial
contact (issue #674/#782's case), and a shelled one after Shell. Each
result now keeps its operands' lines, each line once
(Body::inherit_split_lines), as the old kernel's coplanar join did.

regularization_protection_tests: SMLib's shell makes no section strips,
so the painted cup no longer has more faces than the ordinary one. The
ordinary cup is the box's five kept faces, their five linings and the
rim: 11. A paint over a whole face authors no boundary inside it, so the
painted cup has the same 11 faces; the split side's line stays an edge on
the wall and its lining: 13. The test now asserts those counts exactly
(it asserted more than 11 for both, the old strip route's witness) and
that the split lines survive.

Fixes kernel issue_674_tests::partial_contact_retains_an_authored_split_away_from_the_contact
and body::regularization_protection_tests::stamped_shell_keeps_authored_painted_and_split_boundaries.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:46 -04:00
jyvikoandClaude Opus 5.5 f60bf96dfb Planar sources test: two bodies side by side joined as the record requires
The test helper side_by_side copied the second body's regions by hand,
dropping its voids and keeping its infinite region (region 0) as if it
were a bounded one. Its closed shell was then the outer shell of two
regions, which the portable record refuses ("a closed shell bounds two
regions and encloses one"). The helper now joins the two records with
geom's brep::part::compound, which puts each body's outer shells in the
one infinite region and keeps its bounded regions; the face sources are
still found by plane afterwards, so nothing the test checks changes.

Fixes kernel body::planar_sources::tests::coincident_competing_source_planes_and_tool_planes_stay_unknown.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:46 -04:00
jyvikoandClaude Opus 5.5 049b2bc405 Lumps: a face-source table of another length is refused, never sliced
Body::parts (and so Body::lumps) mapped each piece's faces through the
body's face-source table with a silent `get`, so a table shorter or longer
than the body's faces gave its pieces sources of other faces, or none. The
table is by face position: one whose length is not the body's face count
belongs to another body. The pieces are now refused with "lumps: face
source table does not match the body", as before the SMLib port (the check
went with the old lumps_with_clearance in 66e31bede).

Fixes kernel body::lump_tests::grouping_lumps_does_not_infer_absent_or_misaligned_sources.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:46 -04:00
jyvikoandClaude Opus 5.5 15c31a96fc Kernel: planar source lineage finds each face's support through an index, with no budgets
Which input plane each result face lies on was found by scanning every input plane whose
normal x was within the resolution's angle: quadratic on axis-aligned parts (two thirds of the
faces have normal x = 0), so it was capped at 16 384 faces a body and 2 M comparisons, and the
join of the 20 level-2 sponges of a level-3 Menger sponge (7 326 faces) was refused past the
comparison budget.

The planes are now indexed by their unit normal, in cells twice the bound on two matching
normals' difference (asin(angular) < 2 angular), and in each cell by their offset from a common
centre, searched in the window linear + |a.o - c| |n_b - n_a| that
d_b - d_a = (b.o - a.o) . n_b + (a.o - c) . (n_b - n_a) gives, plus rounding slack. The index
offers a superset; same_support still decides each match, and candidates are taken in the same
order as before, so every answer is unchanged. A plane with a normal not of unit length is
offered to every query. Both caps are removed: results are bounded by inputs capped where they
entered. The descriptor-size budgets on kept roles are unchanged.

Rig, --known-failing, results compared case by case with develop's: booleans (129) and shell
(28) identical except booleans/5126-join-menger-sponge-level-3, which now passes in 38.9 s on
aarch64 and leaves KNOWN_FAILING.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:42 -04:00
jyvikoandClaude Opus 5.5 ffb1e650df Isocurve Analysis: count curves each way, evenly spaced across the face
The curves were held on a 1-2-5 ladder from the world origin, so count 3 on a 40 x 30 face gave 3
one way and 2 the other. They now follow the command's contract: the held parameter at
lo + k (hi - lo) / (count + 1), k = 1…count, over the face's extent. Faces of the body on the same
surface record are spaced together over their combined extent, so a face a boss splits still
shows the same lines straight across the split.

New case cov-isocurve-40-by-30-face-count-3: x = 10, 20, 30 and y = 7.5, 15, 22.5, to 1e-9 mm.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:34 -04:00
jyvikoandClaude Opus 5.5 16d467e14a Point and Plane Along Path: exact on the path's curves by arc length, and a t outside 0…1 is refused
Both walked the picked curve's display polyline: a point a third along an R10 sketch arc was
0.87 µm off (8.6603, 5). They now evaluate the path's exact curves by arc length: lines and arcs
in closed form, a free-form span at the parameter its arc-length integral reaches (body edges by
their record curves, 3D sketch curves by their arc, spline, line or linked exact curves; only a
curve that exists as points alone, an intersection edge or a projected curve, runs along them).
The arc's point is now within 1e-12 mm of (10 cos 30°, 5, 0).

A t outside 0…1 was clamped silently, which the contract (`t: expr, 0…1 along it`) does not
say: it is refused ("t is 1.5: a point along a path is 0 (its start) to 1 (its end) of the way
along it"). The construction cases grade the arc and line to 1e-9 mm, past-the-end is refused,
and a new case takes the middle of a symmetric cubic spline, (20, 7.5).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:34 -04:00
jyvikoandClaude Opus 5.5 cf2b3a62fc Fair Surface: a face of degree 1 one way fairs along its curved way, and a face with nothing free is left as it is
A face of degree 1 in one direction (an extruded spline) was refused with "a fairness term does
not fit the net's degrees": the thin-plate energy's S_vv asks for second derivatives a linear
direction does not have. On every span that term is exactly zero, so it is dropped; the energy is
the bending along the curve and the twist. A face whose held layers are its whole net (a
single-span cubic with its edges kept, an extruded curve's two rows) has no interior control
point: it is left exactly as it is, its energy reported unchanged, 0 steps.

cov-fair-single-span-face-has-nothing-free-to-move passes and leaves KNOWN_FAILING.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 23:17:34 -04:00
jyvikoandClaude Opus 5.5 e7e613b6fb Records: the item budget bounds input, not the kernel's own results (Refs #3992)
The portable record's 4,000,000-item budget refused a real result: the join of a level-4
Menger sponge's level-3 sponges ended with "SMLib export: the mapped B-rep does not validate:
portable B-rep: item budget". The budget guards records from outside the kernel, and a body
the kernel built in memory from inputs already bounded where they came in isn't hostile.

Brep::validate keeps the budget for records read from outside: native design caches
(decode_native_body, behind its own 256 MiB, 1M-per-array and 20M-value caps) and STEP import.
The new Brep::validate_built runs every other check, without the cap, on what the kernel
builds: SMLib's export of an operation's result, a body's record (Body::from_record, after
the decoder has checked a file's), a part of a validated record, the record handed back to
SMLib, and the validity check. Its checks are linear in a record already in memory.

SMLib's export bounded its counts by the same budget; a count is now bounded by SMLib's own
longest array (flat::MAX_LEN, checked on entry), which keeps every offset worked out from
the counts from overflowing, and the redundant topology-length cap goes.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 22:15:38 -04:00
jyvikoandClaude Opus 5.5 29adfd0d7f Kernel tests: the barrel's side is the exact surface of revolution of its arc
The barrel's arc has its centre across the axis, so its side is the inner (lemon) zone of a
spindle torus, which SMLib's torus does not describe (its meridian is on the X side): SMLib
(revolve-spindle) sweeps it as the exact rational surface of revolution. shell_of_a_revolved_barrel
asserted an analytic torus of major radius -10. As the owner decided, it now asserts what
matters: two flat caps and the curved side, the closed-form volume, 14 mm round at mid height,
and after the shell the two offset faces (the inner wall and floor; truck's side was in halves).
Needs SMLib with revolve-spindle (pin bump).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 19:03:36 -04:00
jyvikoandClaude Opus 5.5 bb4299e565 Tests: a drafted cube side leaves the bottom and the opposite side Kept, the rest Modified
Drafting a cube's side about its bottom edge (on the neutral plane) tilts the side and moves the
edges it shares with the top and the two faces beside it: those four are trimmed differently
(Modified); the bottom and the opposite side are untouched (Kept). Truck called all six
Modified; SMLib's history called the moved neighbours Kept. Needs the SMLib fix "history: a face
whose edges an operation moved is Modified, not Kept" (SMLib branch devgreen-kernel-records,
cdaf205) and a pin bump.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 19:03:36 -04:00
jyvikoandClaude Opus 5.5 f3b77d71b3 Tests: expectations for the SMLib fixes of 2026-10-29
With SMLib integration-overnight + b78bd4a (the fixes of 2026-10-29), three
expectations that held a refusal now build, each checked against its exact answer:

- rig fillets/1207-fillet-box-end-edge-into-unblended-round (was ...-refused): the end
  face's top edge of a cube rounded r3 along its top back edge, rounded r1 alone
  (tangent chain off), builds. Its round runs on along y through the r3 round's end
  until that surface drops below it at y = 17 + sqrt(5): V = 8000 - 20 (9 - 9 pi/4)
  - 17 (1 - pi/4) - 0.218236 = 7957.505202 (the last term the section under the round,
  integrated exactly); SMLib gives 7957.505245.
- blend_smlib smooth_edges_and_unfinished_tangent_chains_are_refused_saying_why: the
  same cube builds, at that volume.
- modify_history_tests::smlib::draft_tilts_a_side_and_keeps_its_name: the rod's side,
  a cylinder along the pull, drafts 5 deg to a frustum, radius 5 at the neutral plane
  and 5 - 10 tan 5 deg at the top, at its exact volume.

tests/kernel-cases/fillets/KNOWN_FAILING drops 1557-fillet-vertical-corners-after-
bottom-rounds, which passes now; the other eight still fail, so the gate holds
(81 pass, 8 known failing, no regression).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 19:03:36 -04:00
jyvikoandClaude Opus 5.5 de606715b0 Placement tests: a body mirrored in SMLib reads back from its record valid
Since an operation's result is its record (f11c0c571), a mirrored body is
SMLib's transform read back from SMLib's export, and two SMLib defects there
made it invalid: a mirrored cylinder came back inside out the wrong way
(SmCylinder::IsNurbSurfaceCylinder; its edges 10 to 30 mm off the surface),
and every edge's own tolerance was reset to the body's (SmBrep::Transform).
Both are fixed in SMLib (fix/mirrored-cylinder-from-nurbs e02e63e, c603293,
with e008e82 for a scaled body without vertices);
this test needs the SMLib pin moved past them.

A plate with a through hole and a box with two rounds meeting at a corner,
mirrored in x = 30 and read back from their records: SMLib finds both valid
and their volumes are the originals'.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 19:03:36 -04:00
jyvikoandClaude Opus 5.5 ee9fc37935 Tests: a torus patch to thicken is cut from SMLib's one-face torus
SMLib makes a torus one face, so the face at (25, 0, 0) was the whole torus,
not a patch within half a turn each way. The patch is now the torus's piece
with x, y > 0 and z > 1, bounded by iso lines both ways (planes through the
axis, and z = 1 round the tube), and its thickened volume is the formula's
over the angles its mesh spans. (The sphere cap above it builds once SMLib's
offset takes an open edge's second trim point away from its first: SMLib
devgreen-kernel-geometry; waits for the pin.)

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 12:20:38 -04:00
jyvikoandClaude Opus 5.5 b9d65e6bc8 Tests: thicken across a sharp edge extends the offsets until they meet
SMLib thickens a sheet across a convex sharp edge as other CAD does: each
face's offset is extended until the offsets meet (and trimmed where they
cross inward), where truck bridged the gap with a wedge. Owner decision:
keep SMLib's result. The exact values:
- three faces of a 10 box's corner out by 1: three slabs, a 1 × 1 × 10 block
  along each edge and a unit cube at the corner, 300 + 30 + 1 = 11³ − 10³;
- into the inside corner by 1: 10³ − 9³ (it was refused); half each way:
  10.5³ − 9.5³ (refused too);
- two faces across one edge: 2 · 100 + 1 · 1 · 10 = 210.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 12:20:38 -04:00
jyvikoandClaude Opus 5.5 8075b8f70f Tests: a swept point path is its lines, and rails must turn with a cornered path
A sweep along points follows the lines between them (no wall is fitted through
the points, sweep_sheet_points' contract, as sweeps_along_3d_paths already
says): along a quarter circle of 41 points the sheet is a wall per line, 40,
its area 10 × the polyline's length (within 10⁻⁴ of 10 × 15π); the bent chain
is 2 × 40 walls sharing every seam, 2·41 + 3·40 edges.

SMLib's sweep takes guide rails along a cornered path when each rail turns
with the path at its corners; a straight rail along a bent path is refused
for that reason, not as "guide rails along a path with sharp corners".

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 12:20:38 -04:00
jyvikoandClaude Opus 5.5 6c9c679dcc Tests: a revolved sheet over one radian is one face, untrimmed over its whole span
SMLib revolves the cone frustum's sheet over angles 0…1 as one face, where
truck made two of half a radian each; the face's own span is angles 0…1 by
profile parameters 0…0.8: √125 · ∫₀^0.8 (5 + 5t) dt = √125 · 5.6.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 12:20:38 -04:00
jyvikoandClaude Opus 5.5 2c341006a0 Tests: a cylinder's side and a sphere are one face each, as SMLib builds them
SMLib makes a cylinder's side one face closed round its seam, and a sphere one
face; the tests picked "one half" of the side or "one sixth" of the sphere, which
were truck's pieces. The offset test moves the whole side (one face, area
2π·12·20); the thicken test takes half the side from a cylinder split at x = 0
(π·(11² − 10²)/2·20) and the whole side inward (π·(10² − 9²)·20); the sphere
test takes the cap above z = 5 (solid angle π: π/3·(11³ − 10³)).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 12:20:38 -04:00