rounds_that_fit_are_closed counted faces (the input's plus one per picked
edge: 38, where SMLib makes 50 with its corner faces). It now keeps
validity and no crossed loops and holds the R0.5 rounds on all 24 end-face
edges to the exact volume.
Proof. The part (plate 14 x 21.5 x 10, block 14 x 9.948 x 10 on it, the
5.2 x 7.1 window through both along x) is
14 (215 + 10 (b - a) - 36.92). At depth u into an end face's rounds the
section is that face's outline moved in by d = r - sqrt(r^2 - (r - u)^2),
each edge parallel to itself: the area less L d, L = 2 (21.5 + 20) +
2 (5.2 + 7.1) = 107.6 (the stepped outline's perimeter is its box's), plus
d^2 at each of the six convex corners (two rounds mitred), less pi d^2 / 4
at each of the six concave ones (the two shoulders and the window's four
corners: rounds meeting at a concave corner beside an unpicked sharp edge
are swept round it, the owner's ruling of 2026-10-30). The wall between
window and block side is 1.256 > 2 r, so the offsets stay apart. Over the
round the integrals of d and d^2 are r^2 (1 - pi/4) and r^3 (5/3 - pi/2),
so both ends remove
2 (L r^2 (1 - pi/4) - (6 - 6 pi/4) r^3 (5/3 - pi/2)) = 11.514718.
Graded at 1e-7 of the part's volume. It passes today (aarch64, SMLib).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
issue2422_vertical_after_separate_bottom_rounds compared the face count and
volume (within 0.05) of the vertical round, picked with and without its
bottom mitre, against the same round picked alone, and required every face
meshed. It now holds each of the three picks, on the 40 x 80 x 27 box and
on the same shelled 1 mm open at the top, to the exact volume; the corner
probes stay.
Proof. Horizontal sections, s up from the bottom. Below s = r the four
separate R2 bottom rounds (mitred at the corners) leave the rectangle
moved in by d = r - rho, rho = sqrt(r^2 - (r - s)^2), and where the
vertical round meets them (a sphere octant) its corner is a quarter disc of
radius rho: (L - 2d)(W - 2d) - (1 - pi/4) rho^2. Above, LW - (1 - pi/4) r^2.
With the integrals over the bottom r of rho (pi r^2 / 4), rho^2 (2 r^3 / 3),
d (r^2 (1 - pi/4)) and d^2 (r^3 (5/3 - pi/2)):
V = LW r - 2 (L + W) r^2 (1 - pi/4) + 4 r^3 (5/3 - pi/2)
- (1 - pi/4) 2 r^3 / 3 + (H - r)(LW - (1 - pi/4) r^2) = 86174.445361;
with four such corners it is issue1557_all_vertical_corners_match_analytic
_volume's formula exactly. The shell's cavity, 38 x 78 x 26, is clear of
both rounds (along the corner's diagonal the R2 arc stays 2 - sqrt(2) in,
the cavity's corner is 1 in), so the cup is V - 77064. Graded at 1e-6.
Today SMLib's check refuses the bottom rounds' result (edge and vertex
tolerance 0.97 against 0.01), as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillet_tabbed_plate_outer_loop_and_partial_selection_after_hole only
checked that every subset of the R25 tabbed plate's seven top-outline edges
builds and stays inside the plate. It now first holds the hole's rim round
and the three selections that end only at the plate's sharp concave
corners (the R25 arc's two halves, the tab's tangent run of sides, R2
corners and top, and both) to their exact removed volume; the sweep over
all 127 subsets stays as it was.
Proof. The outline's area A(da, dt), the arc moved in by da and the tab's
run by dt, each element parallel to itself, by Green's theorem: an arc
about c of radius rho from a to b gives
1/2 (rho^2 (b - a) + rho (cx (sin b - sin a) - cy (cos b - cos a))), a
segment p -> q gives 1/2 p x q. At a concave corner (+-4, sqrt(609)) where
only one side moves, the elements meet where they cross (the round runs
into the other wall: the section is the union of the two sides' half
regions); where both move the corner is swept, an arc of radius d about the
corner, traversed clockwise from the arc's normal to the side's (the
owner's ruling of 2026-10-30 for rounds meeting at a concave corner beside
an unpicked sharp edge: the profile swept round the corner edge). Checks:
A(0, 0) = 312.5 (pi + 2 theta) + 4 y + 8 (cy - y) + 8 + 2 pi (disc sector,
triangle, tab, R2 corners), and A(0, 0) - A(d, d) = L d - pi d^2 by the
Steiner formula for the swept offset (total smooth turning 2 pi + 2 theta,
the two swept corners -theta each), agreeing to 1e-15 at d = 0.1, 0.3,
0.5; A(0, 0) - A(0, d) agrees with a 0.004 mm grid to 2e-6. The round's
section at height r sin(phi) into it is the outline moved in by
d = r (1 - cos phi), so it removes the integral of
(A(0, 0) - A(d)) r cos(phi) dphi over [0, pi/2] (midpoint rule, 8192
steps, converged to 1e-7 against 4096). The hole's rim round is Pappus:
(1 - pi/4) r^2 about the axis at 1.5 + r (10 - 3 pi) / (3 (4 - pi)).
Graded at 1e-5 of the removal, the bound the D prism's rounds are held to
(the blend surfaces are SMLib's fits).
Today the three selections build with these volumes (aarch64, SMLib); the
sweep still fails where a subset ends a round at a tangent joint (the x = 4
side without its R2 corner): SMLib cannot end a blend inside a tangent
chain, "the blend cannot end there".
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's blend-overflow ruling of 2026-10-30: a chamfer whose leg runs
off the face beside its edge over another face is refused as too large,
naming the largest size that fits (a 2 mm chamfer on the basin's 1 mm rim
would lower the slab's front face from 30 to 29.382); a full-width chamfer
stays refused. Two tests wanted those chamfers built and cut from the slab:
- chamfer_wider_than_sloped_basin_rim_is_cut_and_a_full_width_one_refused
becomes chamfer_wider_than_sloped_basin_rim_is_refused_naming_the_largest:
(margin, d) = (1, 2), (1, 3), (0.5, 4) and the full widths (0.5, 0.5),
(1, 1) are TooLarge, the body unchanged, and the message names a largest
size just below the rim's width: the full width is refused, so the fit
search (three significant digits of the size asked, step
10^(floor(log10 d) - 3)) ends one step below it, in
[margin - step, margin). The removal formula for the cut chamfer
(basin_rim_chamfer_removed) has no use left and goes.
- equal_slope_rim_loops_stay_inside_the_material: the 2 mm chamfer of the
1 mm rim's loop is refused the same way (largest in [0.999, 1)); the R4
round (tangent side, builds) and the 0.5 blends stay.
The half-width chamfer on each rim, which only had to take something off,
now takes its exact volume. As in chamfer_sloped_basin_rim: the triangle
with legs d on the top and d down the wall towards (20, 10) (run
20 - margin over the 20 drop) has area d * drop / 2 with
drop = 20 d / sqrt((20 - margin)^2 + 400), and the chamfer's length at
depth h is 60 - h between the end walls x = 20 + (30 - z) / 2 (planar:
x depends on z only), so it removes d * drop / 2 * (60 - drop / 3);
graded at 1e-8 as that test is.
Today SMLib refuses the chamfers as too large, but the message does not
name the largest that fits yet ("the chamfer is larger than the faces
beside its edges allow"), the SolidCraft change issue_1080's R30 test
waits for too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's blend-overflow ruling of 2026-10-30: a round that runs past
its face on its tangent side is built on the face continued and cut from
the part, keeping its radius. loop_fillet_as_tall_as_its_wall_consumes_it
still wanted R2.001 and R2.5 on the R13 x 2 disc refused as taller than the
wall; they now must build, valid, with the exact volume.
Proof. The round's section in (rho, z) is the r square at the top edge
outside the circle about (13 - r, 2 - r), clipped to z >= 0. With
t = z - (2 - r) = r sin(theta), the round's inner radius is
rho(theta) = 13 - r + r cos(theta), theta from asin((r - 2) / r) to pi/2,
and the disc keeps pi (169 * 2 - integral (169 - rho^2) dz), dz =
r cos(theta) dtheta (midpoint rule, 20000 steps). At r = 2 it is Pappus,
2 pi 169 - (1 - pi/4) 4 * 2 pi (13 - c), c = 2 (10 - 3 pi) / (3 (4 - pi))
(checked to 1e-9 in the test); at r = 2.5 it is 957.692239 mm3, the
ruling's number, the same integral as
rounds_past_the_bottom_of_a_wall_are_cut_from_the_part's. Graded at 1e-6
as that test is.
Today SMLib fails the R2.001 round (status 1001): a convex round past its
face is not yet built by subtraction, the cause fillets/KNOWN_FAILING gives
4782 and 5158.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
a_round_into_a_hole_is_cut_by_it (issue_324_tests.rs) built rig case
fillets/324-fillet-over-hole-overlap's body, but cut its hole with a cylinder
longer than the block (z -1 to 11) where the rig extrudes a sketch circle
flush. The new case fillets/324-fillet-over-hole-cut-by-overlong-cylinder
builds it that way (solid.cylinder, base z -1, height 12, cut) and holds it to
the same hand-derived answer: block 40x20x10 less the r3 hole at (20, 14.5)
(282.74) less the R4 round on the top edge at y = 20, 40 (16 - 4 pi) = 137.35,
plus what both remove, the integral over y in [16, 17.5] of
(4 - sqrt(16 - (y - 16)^2)) * 2 sqrt(9 - (y - 14.5)^2) = 0.375830 (re-derived
with the substitution y = 17.5 - s^2, 200000 steps):
V = 8000 - 90 pi - 40 (16 - 4 pi) + 0.375830 = 7580.287315, and G1 on the
blend. It passes today (aarch64, SMLib), as the flush case does, so it needs no
KNOWN_FAILING line; the unit test, a duplicate of the two cases, is dropped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillet_mixed_arc_and_line_joint_preserves_both_section_radii put R0.5 on the
D prism's top outline and checked 258 points of each mitre edge against the
cylinder and torus to 1e-7 in r squared, through the record's edges. The rig's
fillets/485-fillet-d-prism-top-outline-arc-and-flat builds the same prism with
the same radius and grades the removed volume to 5e-5 (a 0.12 mm3 loss shows)
and G1 on every blend seam, which is what the mitre's accuracy is for.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A box edge chamfered 2 and by two distances (3 and 1, and flipped, told apart by the
centre of mass); a pocket's rim chamfered 1, by two distances, 4.9 (fits), and 5 and
5.5 (refused by the owner's rule on full-width chamfers: built at 5 today).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A box edge rounded, then the edge meeting it at the corner, in both orders (both the
three-edge rolling-ball corner); r3 then r2 (the r2 round's torus about the r3 round's
axis, by Pappus); an L-bracket's front inner outline after its bend round; a block's
top edge after the arc round at the cylinder (fails today: G0 at the round's end on the
crease); a curvature round after a curvature round with Tangent chain off.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Inside bend r3, outside r5, both concentric (r3 and r8), the inside r35 using up both
inside faces, r36 refused naming 35, and the inside bend Type: Curvature.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Top and both rims rounded r1 and chamfered 1; the top rim rounded r10 (as deep as the
plate), r12 (past it on its tangent side: built by subtraction, fails today with
status 1001) and Type: Curvature; chamfered 9.9 (fits) and 10 (the full depth:
refused by the owner's rule, built today). Volumes by Pappus.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A rectangular pocket's floor edges, rim edges and both rounded r2, the rim r5 as deep
as the pocket; a boss's root r2 and r10 (as tall as the boss) and its top rim r2.
The rim cases fail today: SMLib puts a corner patch where two rim rounds meet at a
concave pocket corner, where the rounds running into each other make a mitre (four
faces more; the volumes agree to 5e-4).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A block whose sides meet the cylinder at creases: the concave arc at the wall above
the block's top r2, the cylinder's top rim r2, the block's long top edge r2 with
Tangent chain off and Type: Curvature. A block as wide as the cylinder, its sides
running tangent into the wall: the arc and the long top edge each rounded alone
(built or refused as continuing tangentially). Volumes by Pappus or one-dimensional
quadratures of the exact sections, the round ended by the planes it runs into.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Three edges at one box corner rounded r1 and r3 with the rolling-ball corner, r3 with
Corners: Curvature at its default setback and at 3.5, and refused at 3 (the radius);
the corner chamfered 2; all twelve edges rounded r2; one edge rounded Type: Curvature.
Volumes in closed form (strips plus sphere octants, half-space intersection, the
rounded box as a Minkowski sum, the quintic section's area 113/756 s^2); G1 at every
round's seam, G2 for the curvature round and the corner patches.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Stale since 84bd2daad (the Fillet feature rounds each pick's tangent chain). After a and b are
rounded at 2 mm and meet in a mitre, the mitre's seam leaves c's end along c, so c's chain is c
and the seam; rounded at 2 mm, as the issue1557 tests pick, the corner is a sphere octant.
Proof: the 20 mm cube less its three rounds, each (1 − π/4) r² over its 18 mm straight part, and
the corner's 2 mm cube less the octant, r³ (1 − π/6): 8000 − 3·(1 − π/4)·4·18 − 8·(1 − π/6) =
7949.834793498635. Measured 7949.834793513291 (1.8e-12 relative), 10 faces, valid; the check is
tightened from 0.05 mm³ to 1e-11 relative.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Stale since 84bd2daad, which gave solid.fillet each pick's tangent chain by default. After the
long top front edge is rounded, the front-left upright meets the round's end (the quarter circle
on the left face) along its tangent, and that circle meets the top-left edge along its tangent:
the second fillet rounds the upright and the top-left edge. The "together" fillet picks the
three edges ([20, -21, 10], [0, -21, 5], [0, -10, 10]); one by one and together remove the same
volume within the display meshes' 2e-4 (it read 60.649 vs 43.185 with two picks).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
tangency-labs/smlib#64 builds a tapered wall that closes partway up (its neighbours meet above
its apex), so the 0.2 mm slot of a 10 mm square tapered 10° out over 2 mm now builds where it
was refused. The test, renamed for what it checks, asserts the slot's solid is valid with its
exact volume and keeps the ring's refusal (its 0.3 mm hole closes entirely).
Proof of the volume, t = tan 10°: every wall moves out of the material by z·t at height z. The
square grows to 10 + 2zt, so without the slot ∫₀² (10 + 2zt)² dz = ((10 + 4t)³ − 1000)/(6t).
The slot narrows to 0.2 − 2zt and keeps its length 8 (its end wall and the square's side both
move up by zt); it closes at z = 0.1/t = 0.567 and takes ∫ 8 (0.2 − 2zt) dz over 0..0.1/t =
0.08/t. Volume ((10 + 4t)³ − 1000)/(6t) − 0.08/t = 213.984095421783; measured to 1e-6.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
tangency-labs/smlib#63 raised SMLIB_CURVE_MAX_CURVES from 4096 to 16384; CURVE_MAX_CURVES
follows it, so a profile of 5000 segments (a modelled thread, a fine polygon) extrudes:
kernel tests::measure_of_a_body_with_many_faces passes (5002 faces, 15000 edges, 10000
vertices).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- #63: a knife edge (two faces tangent along it, folding back) rounds to the ball touching both
faces back from it; a curve list takes up to 16384 curves (SMLIB_CURVE_MAX_CURVES); a stitched
solid is a nested solid, its cavities void; booleans pair each face only with the faces whose
box comes near its own, the closure test of a new face searches from both its sides, and a new
edge from a faceuse shell to a wire keeps the faceuse shell: a row of Menger sponges joins in
near linear work.
- #64: a tapered wall that closes partway up ends at its apex, its neighbours meeting above (it
was refused as SMLIB_ERR_WALL_CLOSES); a round of revolution offset in past its radius has no
offset; a round along an arc turns from its start section, not from the arc's frame.
- #65: capi tests, the Menger row join counts its work (smlib_work_counters) instead of timing it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
tapered_extrude_swallows_a_short_tip expected the prismatoid whose two tip
corners run straight to the top's tip (h/6 (A0 + 4 A_mid + A1)), the solid
the old offset-and-rule construction built: its tip triangle leans about 40
degrees, not the 5 degree taper. With every wall drafted 5 degrees the tip's
wall is a triangle that closes where the long sides meet across it, at
z* = 0.126237833 (offset 0.011044379), and above that the long sides meet
along a ridge. The section at height z is the profile's lines moved in by
z tan(a): a quadrilateral below z*, a triangle above, each area quadratic in
z, so Simpson's rule on each piece is exact: V = 72.883284979193. The old
value, 72.882657253174, is 8.6e-6 off, past the test's 1e-6. SMLib's
DRAFT_CORNER_ROUND path builds exactly this solid (72.883284979193, 6 faces);
the default curvature rule still refuses it (SMLIB_ERR_WALL_CLOSES at
(20, -0.01, 0)), so the test fails until the fork builds a wall that closes
partway up.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
shell_thicker_than_a_rim_is_refused expected the "rim or ledge" refusal from 9508ee749,
added because truck's face offset turned the top face inside out and returned a body of
about twice the volume. SMLib builds the exact sharp-edged offset, and its volumes are the
closed form, so the test now checks those (renamed
shell_of_a_basin_past_its_rim_keeps_the_rim_solid).
Proof. Slab [0,100]×[0,60]×[0,30]; pocket lofted from x 20..80, y 4..50 at z 30 to
x 30..70, y 20..40 at z 10, its sides the planes x + z/2 = 35, x − z/2 = 65,
y + 0.8z = 28, y − z/2 = 35 (normal lengths √5/2, √5/2, √1.64, √5/2). Shelled open at
z = 0 by t, the cavity is the slab shrunk by t (x t..100−t, y t..60−t, z 0..30−t) less the
pocket grown by t (each plane moved out by t·|n|, floor z = 10 − t). For t ≤ 6 the grown
pocket stays inside the shrunk slab in x and at the back (50 + 0.618t ≤ 60 − t); its front
reaches y = t at z0 = (28 − (1 + √1.64)t)/0.8, below 30 − t from t ≈ 2.70 (the rim stays
solid above z0). With W = 30 + z + √5 t,
grown(t) = ∫[10−t, z0] W (7 + 1.3z + (√5/2 + √1.64)t) dz + ∫[z0, 30−t] W (35 + z/2 + (√5/2 − 1)t) dz,
V(t) = 180000 − grown(0) − (100 − 2t)(60 − 2t)(30 − t) + grown(t),
grown(0) = 33866.667, so V(1) = 17105.6240415, V(4) = 63560.2492284,
V(6) = 90113.9202101. SMLib measures 17105.6242, 63560.2492, 90113.9203 (≤ 1e-8
relative). The test computes the closed form and checks each shell to 1e-6, with the
centroid inside its box and on x = 50 as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The test offset the sphere's top patch to get a fitted B-spline sheet. That held on truck,
whose sphere came in several patches and whose sphere offset was fitted. On SMLib the
sphere is one face: offsetting it closes up, so it is a solid by design (surface_offset.rs,
"Faces that close up make a solid", and its test a_sphere_is_fitted_and_refused_past_its_centre
asserts exactly that), and SMLib's offset is exact, a sphere of radius 22 with no control
points, which surface.fair refuses. Body::is_surface was right: the record lists the offset's
closed shell as the outer shell of a material region (Parts::canonical), so it is a solid
whether read from edge uses or from regions.
The test now fairs the patch on the non-planar rim of a box cut by a sideways cylinder (the
cover in patch_trim_thicken_and_stitch), a one-face B-spline sheet: energy 0.7185 → 0.6938 in one
step, edges unmoved bit for bit, undo/redo/reopen and the refusals as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
hostile_params_never_panic built a box, a sketch and a rectangle afresh for each of the ~3000
calls it makes per command. SMLib serialises every call behind one process-wide lock, so those
boxes were built one after another whatever the number of threads: 20 threads made 4000 boxes
in 7.8 s, one thread 200 in 0.31 s (1.5 ms each). The fixture was nearly all of the test's time
(8814 of 8823 thread-seconds over the first 72 commands on the aarch64 box; the commands
themselves 9 s, none over 0.5 s), and the test took 2195 s in develop CI.
It now builds that model once per command and gives each call a copy of the session with its
design, model, undo, redo, open sketch and log, sharing the bodies as undo does. Every command
still gets every parameter name with every hostile value, from the same starting state. A new
check runs Cancel Sketch, two undos and a redo on a copy and on a session built afresh and
finds the same designs, with the copied session untouched.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
encode_native_body turned the whole saved record into a serde_json
Value (a map with an owned key for every field of every face, edge,
curve and pcurve), checked it, counted it, then wrote it out. Building
that tree was most of the cost: on the Menger level 4 sponge (3 tools,
--save) the 101 bodies the model cache encodes, 535 MB of encodings,
took 24.1 s of encode_native_body, 20.8 s of it in to_value.
binary::write_serialized is a serde Serializer for the tagged binary
format: it writes each value as it is serialized and applies the same
checks as it goes (nesting, string and array budgets, floats within
1e12, the value budget, the size limit). An object's entries are put in
key order when it closes, as the JSON map held them; floats that are not
finite are null, as to_value made them. The bytes are the same: a test
encodes plain, blended, cut, extruded, painted, split, open, round and
far-placed bodies both ways and compares them, and all 101 Menger bodies
(6 to 28 412 faces, 15 kB to 68 MB) encoded both ways in one run were
byte for byte the same. The JSON-value writer stays for the tests that
build hostile records.
Menger L4 3-tool --save, two runs each: encode_native_body 24.1 / 25.3 s
before, 3.0 / 3.0 s after (the longest call 1.34 s -> 0.29 s); the run
41.2 / 41.4 s wall before, 39.1 / 39.2 s after (the encodings run on
16 threads).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A To Object extrude to a curved face runs its tool through the target and
cuts the target out of it. The SMLib boolean carries no extrusion face
sources (they stood for the untrimmed profile), so sheet_tool_span, which
read the tool's depth and footprint only off its extrusion caps, gave up
and the intersect was refused as unrepresentable.
The tool's current geometry says what it is: the kernel's prism
certificate (prism_measure, the one component copies are compared by)
reads off the exact record whether a body is a uniform prism along a
direction, its two cap levels and its section of lines and arcs. It is
now public as certified_prism_section, and sheet_tool_span uses it when
the caps don't certify the tool: the levels are the depth, the section the
footprint the To Object cut is bounded by. A tool trimmed to something
that is not a prism (a curved roof over it) is still refused.
partial_depth_intersect_curved_to_object_preserves_current_trimmed_cap_footprint
passes: the tool is the square 20 ... 30 less the pin's circle (radius 2),
z 0 ... 1, 100 - 4π, as the test's own witness extrude measures it. A
kernel test reads that section off the trimmed lump.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The refusal "capture the source occurrence position before generating a
legacy face profile across components" lost its test when Offset Face got
an exact history name (b6c3bf3c5). A half of a box's top that Split Face
divided still has neither a construction certificate nor an exact history
name, so Extrude from that face, in a component whose occurrence has an
uncaptured move, takes the legacy path and is refused there; the document
and the pending moves stay as they were.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
end_at_wall takes the plate's end strip off a wall that stands on part of
an edge of the fixed face: the strip's two corners and its two edges go.
They were filtered at their places in the face's lists, counted from the
bend's edge, which pairs corner j with edge j only while the places do
not run across the lists' start. SMLib merges the plate's end strip and
both walls at x = 100 into one L-shaped face whose loop starts on the
strip, so the corners left were each followed by the next one's edge:
the bend's edge took the wall end's face and the wall end took the
plate's. The bend then ran the wall's full width and no relief cut it.
Both lists are now kept counted from the bend's edge.
a_wall_on_part_of_an_edge_meets_a_wall_at_a_relieved_corner_and_is_relieved_at_its_end
passes: bends [22, 92] (was [26, 96]). From the geometry: T 2, R 2, the
setback R + T = 4 on the plate from y = 0 and from x = 100; the round
corner relief 8 across is centred on the setbacks' corner (96, 4), so it
takes 4 off the end of each bend there: the long bend from x = 0 to
96 - 4 = 92, the short one from y = 4 + 4 = 8 to 30, 22 long.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The kernel switch broke these tests only through their counts, which record how a kernel splits
faces rather than whether the result is right. Each now checks its intent:
- a fitted circle is the exact circle (centre, radius, a full turn), not "one segment";
- the tight bend sweeps a valid solid of Pappus' volume, πr²(40 + 5π/2), not a count of faces,
edges and vertices;
- the Pi case keeps each outer side one face, stays valid after every feature and rebuilds the
same topology at 32 whether built there or edited there, without a hard-coded table of totals;
- a certified paint stays on the wall's radius and covers as many faces after an edit, a copy
and reopening as when it was painted;
- the offset sleeve and the extended strip are checked by their exact areas only.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
saved_curved_strip_projection_is_lost_after_exact_wall_coalescence built its "old" strip by
cutting the cavity raw (paint turning off the construction shortcut), where truck sewed the cut
slab by slab and split the outer round at the cavity's floor. SMLib cuts without slabs: the raw
cut's round is one face, so there was no piece to save a projection on, and the test stopped at
"must have a piece suffix". The link is now what such a build saved, written out: the face name
`F2:blend:F1:+x|F1:+y#1` (the lower piece, numbered up its spread) and the piece's projection on
YZ, the rectangle y 24..30, z 0..2 (the quarter round from (40, 24) to (34, 30), its arcs and
straight sides), 12 mm³ when extruded 1. The current wall is checked to be one face with that
stem and no planar authority.
The test still fails: the link is found on the whole wall ("was split; using the nearest
piece"), not lost, and the strip's material grows to 6 × 30 × 1 = 180 mm³. project.rs takes a
missing piece as removed only on a certified planar or coalesced face, which truck's shell
made and SMLib's does not. That is a persistent-name decision for the owner (see the PR).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillets_on_tapered_bosses_saved_before_still_find_their_edges compared the part with
69454.885209 mm³, what the truck build that saved it measured. In closed form: the 80 × 40 × 20
block (64000); the 20 × 20 boss 10 high tapered 5° in, a frustum to a 20 − 20 tan 5° square
(3660.251034); the Ø16 boss tapered alike, a cone frustum to radius 8 − 10 tan 5° (1798.751833);
less the R1 round on a sloping corner, the corner's section r²(cot φ/2 − (π − φ)/2) at its
dihedral angle φ = 90.435° times its length between z = 20 and 30 (2.124401), and the R0.5
round all round the cone's top, the section at the rim's 95° turned about the axis by Pappus
(1.928463): 69454.950004. SMLib's part measures 69454.950004.
The test still fails before that check: Fillet2's saved edge `F4:side:c1#1|F4:top#[F4:side:c1]`
names a half of the cone wall truck built, which SMLib builds whole, so it is found with a
"was split" warning (a persistent-name question, see the PR).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since 0a216d692 tangent and curvature extensions are SMLib's G1 and G2 extension of the surface
(smlib_extend_sheet, CreateExtendedSurface), and the face stays one face on it, as
surface_extend's docs say; extend_a_cylinder_strip_every_way still counted truck's separate
run-off face (2). It counts 1.
The test still fails after this, on the curvature run-off's area (see the PR): SMLib's G2
extension of the quarter cylinder by 5 gives 413.882 (a section 4.986 long), where the test
works out the parabola's 418.182.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
cut_keeps_posts_joined_while_apart_in_one_body expected the reply's `bodies` as
["Case", "Case (1)"]. That list is the state's order, which is SMLib's lump order (the -x half
first); the names follow the pieces' faces (lineage::order_lumps, 08cf526fe): the piece whose
least face name sorts first keeps "Case". That is the +x half, whose least is `F1:+x`, before the
-x half's least, its piece of `F1:+y`. The test now checks the names as a set, that the +x half
(from x = 1) is "Case" and the -x half (from x = -30) "Case (1)", and each half's volume as
before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since 09c979a4b a circle is one closed arc, so an extruded circle's wall, a hole's wall and a
cylinder's side are one face each, closed along a seam. Tests that counted truck's two halves:
- certified_annulus_side_rows_follow_radius_edits_and_clone and
certified_side_transfer_preserves_geometry_and_unsupported_taper_refuses_atomically: the
painted outer wall is 1 face (every vertex of it still at the painted radius), not 2;
- offset_surface_of_a_cylinder_and_a_box_top: the offset sleeve is 1 face (its area 2π·12·20
unchanged);
- press_pull_then_curved_face_offsets_it: a click on the hole's wall offsets its 1 face;
- pi_case_faces_per_step_at_both_heights: each standoff (a ring, Ø6 round a Ø2.5 hole) adds 4
faces, not 6: its outer and inner wall, its top, the floor inside its hole. So 23 after the
first and 35 after the pattern of four; the port openings (3 × 4), the end cut-out (4) and the
five vents (5 × 4) are planar and add what they did: 47, 51, 55, 71.
- the_round_sides_of_a_thin_ring_are_named_by_the_circle_they_run_beside: a thin ring 2 thick
about the R10 circle has two walls, `F2:wall:c1:left` (radius 9: the counter-clockwise
circle's left is inside) and `F2:wall:c1:right` (radius 11), with no numbers; each name is
found again by a point on its own wall.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
box_and_fillet_have_stable_wire_records compared the encoding of a box and a filleted box
with records truck built (2f4d6acac). Since f11c0c571 an operation's result is the record
SMLib gives, which numbers the box's faces in its own order and the fillet's edges by its
history, so the golden differed in face order, face sources and edge history, not in the
encoding. Rewritten with NATIVE_BREP_BLESS=1 and checked against the geometry: the box 6
planes, 12 edges, 8 vertices, each face source's plane its face's; the filleted box 7 faces,
15 edges, 10 vertices (one edge replaced by a face: +1, +3, +2), the round a cylinder of radius
2 along x on the axis (y, z) = (2, 8), 2 from y = 0 and z = 10.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since 09c979a4b a full circle in a profile is one arc of a whole turn, so what is built from
it is one closed edge and one wall closed along its seam. Five kernel tests still expected
truck's halves:
- a_small_hole_in_a_large_spline_face_cuts_cleanly: the Ø1 hole adds one face (its wall),
not two; the removed volume (π · 0.25 · 40) is unchanged.
- fit_loop (two mesh_convert tests): a fitted circle is Loop2::circle, one segment.
- tight_bend_counts: a Ø10 tube swept up 20, round a quarter turn of radius 5, along 20. The
circle starts at (5, 0), which runs up to (5, 0, 20) on the bend's axis, where the turn
leaves it: the bend face has no seam and both straights' seams end there. By the ladder's
rule (each whole curve once, each seam): 5 faces (2 caps, one per path segment), 6 edges
(4 circles, 2 seams), 3 vertices (the seams' ends: (5,0,0), (5,0,20), (25,0,20)), the
record's own counts.
- extruded_circles_go_as_cylinders: the record holds the wall as the cylinder it is (one
face of three), no longer a rational spline; it still goes into SMLib as its cylinder.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A folded edge's Hermite pcurve on a bend's form breaks where the edge's angle crosses a
quarter. At the 120 degree corner with flanges at 60 and 90 degrees under a tear, an edge
starts 3.25e-12 of its parameter short of a quarter: the crossing was kept as a break
(breaks within 1e-12 of the parameter merged), the pieces halved to 1.6e-12, and SMLib,
given knots 1.6e-12 apart, handed the pcurve back with 15 equal knots at degree 7 ("SMLib
export: pcurve: loop 0 use 1: given pcurve: portable B-rep: knot multiplicity"). A crossing
whose point on the edge lies within the pcurve's lift accuracy (FOLD_TOL of the edge's size)
of the previous break is that break; the end is never merged into the start.
Fixes sheet::tests::every_pair_of_angles_is_torn_or_keeps_its_notch (torn pairs 37, 37, 27).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Two expectations encoded truck-era output:
- a_flange_bent_inside_keeps_the_base_sketchs_arcs_in_the_flat_pattern_and_the_dxf: the
DXF has 7 LINEs, 4 ARCs, 11 shapes (was 9, 4, 13). The flat outline is SMLib's exact 2D
union of the plate, the bend zone and the flange panel; a zone's side and its panel's side
meet in line, and a region's boundary has no vertex in the middle of a straight run, so
each flange side is one line: 6 outline lines (plate top, left, right; flange sides and
end) and the bend's centre line. The same reason as 5d25684a1 gave for
a_base_trimmed_for_a_flange_keeps_its_arcs (12 to 10 edges). Areas, the bend length and
the volumes are checked as before and hold.
- hole_beside_two_adjacent_edge_flanges_cuts_and_bends_stay_guarded: the folded volume was
14057.2 +- 0.1, a faceted measure; since 32ae0cd9c the measure is SMLib's exact integral,
14057.3837123. Exactly, a folded sheet holds its flat area A times t, less each bend's flat
strip L·t·(R + K·t)·π/2, plus its sector L·t·(R + t/2)·π/2: t·A + t²·(½ − K)·(π/2)·L. With
t = R = 2.5, K = 0.44, A = 5597.0353454 (the flat pattern) and L = 75 + 35, that is
13992.5883635 + 64.7953485 = 14057.3837120, within 2e-11 relative of the measure. The
test now checks that identity to 1e-9.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A face's sheet name is the name 80% of its mesh triangles' centres agree on. SMLib's
mesher fans a 1 mm rim (30 mm tall) into four triangles about its middle; two of their
centres lie 1/6 mm from the panel's top or bottom face, inside the 0.2·t tolerance, and
took that face's name, so the rim got no name (rim.side0/side1/ext0/ext1 of the tray's
flanges: 6 faces unnamed). A flat face's name now needs its plane to face along the
triangle's normal (within 1e-3); otherwise the point is a rim's, a bend's or an ext rim's.
No face changes name: these faces had none.
sheet::face_names_tests::a_trays_faces_have_readable_sheet_names_that_follow_its_size now
passes its naming checks and fails later, on the point named_face_point gives for a rim
(the roomiest triangle's incentre, 0.497 mm from the rim's edge, not 0.5).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A hole drawn on a flange's face and cut through ("direction": "negative") was refused as
"below the supported 0.000001 mm extrusion resolution": the flange panel's frame, turned
up by the cosine and sine of 90 degrees, puts the panel's origin at -1.9999999999999998
along the sketch normal, so the cut ends 2.2e-16 mm short of the sheet's far face and
reads as a layer 2.2e-16 thick. A depth within four units in the last place of the
numbers it is worked out from (the frame origins, the tool's span and the thickness) now
lands on the face. A real thin layer stays: a 1e-8 mm layer of a sheet 1e5 mm from the
origin (bound 9e-11 there) is still refused
(partial_depth_intersect_sub_extrusion_resolution_layers_refuse_atomically passes).
Fixes sheet::tests::a_sketch_on_a_sheet_face_follows_the_sheet_when_its_thickness_changes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since 09c979a4b a circle in a profile is one closed arc (Loop2::circle). The sheet's
faces passed it to the sew as one arc edge from a point back to itself, which the sew
refuses ("sew: a degenerate edge"): a sewn edge runs between two vertices, and an arc
edge is the circle through its ends and middle. A disc's flange failed (first with the
4-face minimum, then with the degenerate edge). Each closed curve of a cell is now split
into its two exact halves (Seg2::split_half) where the cell's edges are prepared, as a
hole's wall already came out: a disc is two caps and two half walls.
sheet::tests::tiny_cut_inside_exact_circle_survives_unfold_refold_and_dxf now builds the
disc flange and fails later, on SMLib's extrude of the 50 nm tool (an SMLib tolerance
defect, reported separately).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The case expected "drill 6.75 mm for M8", the major diameter less the pitch.
Since 05f1c6b9a (Tapped holes: the tap maker's drill for every form) a tabulated
size names the tap maker's drill, 6.8 mm for M8 x 1.25 (Yamawa YEU23 p.704), as
case 2115 already grades and engine thread_tests.rs asserts; major less pitch
is for a size no table lists. The refusal itself and its reason are unchanged.
The case passes and leaves threads/KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The zero-area triangle is dropped (previous commit): the box converts with six
faces and V = 1000 mm^3, as the case expects.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A triangle whose corners lie on one line (or weld into one another) adds no
surface, so welding now drops it, with any corner only it used, instead of
refusing the whole mesh as having a degenerate triangle. The closed and
consistently oriented check that follows still refuses a mesh that needed it to
close, and a mesh of nothing but such triangles is refused by name. Dropping its
unused corners keeps a dropped triangle from widening the part's extent, which
the prism search reads from every position.
Regression test a_zero_area_triangle_is_dropped: the 20 x 10 x 5 box with the
case's extra triangle (0,0,0) (10,0,0) (20,0,0) converts to six faces and
V = 1000 mm^3.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fixed_seeds_run_clean expected the join of a box touching the first only along
an edge to be refused with "zero-thickness edge contact". Since 94ee28d5c (doc:
a join keeps solids that only touch as separate bodies) such a join succeeds and
keeps the new box a body of its own with an along_edge notice, which
join_touching_along_an_edge_keeps_a_separate_body asserts in engine tests.rs.
The seed now expects that: the notice, two bodies, each valid, and the volumes
unmoved, 25 x 15 x 10 + 17.5 x 17.5 x 20 = 3750 + 6125 mm^3.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's thickening of the test sheet makes a top face of 72 x 78 control points,
which the 4096-point cap refused (TooLarge) before the solver saw it. The band
cap (2^21 entries, 16 MB) is what bounds the system's memory and its
factorisation (at most n min(n, bw)^2 work); the 72 x 78 bicubic net needs
5320 unknowns 213 apart, 1.14 M entries, well within it. The point cap now
bounds only the per-step energy sweep and the net's copies: 2^14 points, above
the band's own limit for square bicubic nets (about 90 x 90), so a face is
refused for the system it needs rather than its size. The hostile-input test
asks for 129 x 129 and checks the refusal is TooLarge.
a_body_face_is_faired_with_its_edges_untouched_and_its_history_kept passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The README demo's Raspberry Pi case stands four standoffs on its floor: Extrude2's ring of
radius 3 round a 1.25 hole, patterned by RectangularPattern1. Each is its outer wall, its inner
wall, its top and the floor inside it: four faces. The recorded counts were truck's, which made
each cylindrical wall two halves (six faces a standoff): 25 after feature 6, 43 after the
pattern, and 8 more than now at every step after it. On SMLib each wall is one face closed on
its seam, and the counts are 23, 35, 35, 47, 47, 51, 51, 55, 71 from feature 6 on (the feature
names show it: F6:side:c1, F6:side:c2, F6:top and the floor piece bounded by F6:side:c2 per
standoff). The outer sides stay one face each, and (b) and (c) still agree step by step.
Fixes cli rebuild_topology::pi_case_faces_per_step_at_both_heights.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- A modelled thread reopened with the designation 1/4-20 UNC on the M8 it was made as: the
thread is metric, and since b4549d270 (threads in the standard forms) an unknown designation
is named with its form: "unknown metric thread `1/4-20 UNC` (like M8 or M8x1)". The test looked
for the old wording, "ISO metric".
- Press Pull on a hole's wall opens Offset Faces with the whole wall: one face, closed on its
seam, on SMLib (a cylinder wall was two halves on truck).
Fixes ui-egui dialogs_thread::contribution_tests::expanded_catalogue_rejects_external_taper_holes_and_nonmetric_thread_features
and preselect_tests::press_pull_then_curved_face_offsets_it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A face on a B-spline surface closed around u (first and last control columns the same) may lie
across the surface's start without winding round it: the strip on a radius-3000 rational
cylinder whose seam is 0.001 rad into the strip. A kernel's trims run inside the surface's
knots, so its pcurve came back clamped at the start, 2.28 mm off its edge, and the strip was not
imported.
Before seams are added, such a surface is started anew in the middle of the stretch of u the
face leaves free (each loop followed round, unwrapped across the start; a face winding round is
the seams' to handle): the new start inserted to full multiplicity and the piece after it put
before the piece before it, a period on. The same points, a period apart in parameter before
the new start: exact. The face then lies inside the knots.
Fixes kernel step_in::tests::explicit_outer_bound_crossing_a_closed_nurbs_seam_stays_trimmed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>