The kernel has no boolean retries now, nor their diagnostics
(capture_boolean_diagnostics, BooleanDiagnostics, BooleanStrategy), nor the near-coaxial
crescent (coaxial_overlap, coaxial_candidate, with_attempt_budget). What read them goes:
- doc: FeatureResult and the evaluation cache carry no boolean diagnostics, and no "Boolean
retry" warning; the saved model no longer writes them (an older file's are ignored);
- engine: timeline.inspect / feature inspection drop `boolean_diagnostics`; fuzz runs and
the CLI fuzz summary drop their retry counts;
- inspect.interference: each pair is the bodies' Intersect, measured; the near-coaxial
crescent, the by-piece intersection of bodies in several pieces and the unverified notes
go (the command's doc no longer lists near_coaxial);
- inspect.clearance: an overlap is the bodies' Intersect, measured near its region; the pin
tries, the cut-down copies of large bodies (clipped, narrowed), the union cross-check
(union_disagrees, contradicted) and the malformed-part check (plausible) go, and the
measure near the origin passes its move's error on.
Tests: the retry test and the unit tests of the deleted checks are removed; the barrel join
test (tests/boolean_diagnostics.rs, now tests/barrel_join.rs) keeps its geometry checks;
the pin-in-bushing test expects the filleted case measured; assertions on empty diagnostics
and on near_coaxial are dropped; the corpus fixtures lose the diagnostics key and the one
retry warning.
(not built: base in progress)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
doc's FeatureResult has no boolean_diagnostics any more (truck's Boolean
retry reports, gone with truck; SMLib's boolean has no retries). The
timeline.inspect and doc.inspect replies drop the key.
Tests of the removed reports: tests/boolean_diagnostics.rs is deleted (it
checked truck's retry events and their survival through the cache, undo and
reopen); the assertions that a feature's report had no events go from
features_more_tests, patterns_tests, hole_face_tests and tests/rim_cut (the
rest of each test stays). The CLI corpus's expected replies
(move-bodies, issue-489-stacked-join, issue-616-lid-ribs) drop the key; the
issue-616 one listed a planar_fallback event. docs/robustness.md: its
section on retries becomes one on SMLib's booleans, which have none.
Left to the blends work: engine fuzz.rs (its retry-event counts) and
clearance/interference (capture_boolean_diagnostics, coaxial_overlap,
with_attempt_budget).
Not built: base in progress (kernel-smlib/no-truck 66ab6b7f does not build).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
extend_surface keeps its signature, options and error messages. One model:
SMLib extends the surface past a side of the face's parameter box
(smlib_extend_sheet, CreateExtendedSurface: natural continues the end spans,
tangent G1, curvature G2) and the face stays one face on it, tagged so the
face is Modified and its sides keep their edges. Several picked sides grow
the box on each. Up to a target, the face is extended 50 body sizes past
its edge and trimmed back with trim_keep (SMLib's exact intersection),
keeping the piece the face lies in. Back to the bounds is untrim of the
picked edge's face, in place, with its holes; one already there is
refused. A plane's straight edges with neighbours lengthened still go
through surfaces::extend. Edges are picked on the schema 4 record (samples
of each edge's curve), an edge two faces share or of a hole refused as before.
Not ported (every far edge there was a cubic fitted through marched
samples, which the exact-B-splines rule forbids): an edge that is not a
whole side of its surface's box (trimmed edges, curved planar edges such as
a disc's, a notch), mitred corners on such faces, sides run square to the
edge on a non-box face, and bodies of more than one face. These now answer
"not supported yet: ...". Tangent and curvature no longer add a separate
run-off face: SMLib's G1/G2 extension is one face (the engine's
surface.extend description says so).
Tests ported keeping their assertions: the planar extension, the cylinder
strip along its axis, around and both (now an extruded arc, not a truck
revolution), the extruded strip, the parabola extended naturally (now a
conic extruded), back to bounds (the saddle from loft_sheet and trim),
hostile requests. Deleted, as what they test no longer exists:
neighbours_lengthened_or_square, self_intersecting_extensions_are_refused,
a_disc_grows_by_its_curved_edges, neighbouring_faces_extend_together, the
tangent/curvature run-off half of the B-spline test, and
a_continued_bspline_is_unchanged_on_its_range (the deleted continue_span).
SMLIB_REV: fork 9531966 (tags carried through untrim and extend).
(not built: base in progress)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
With no targets picked, an extrude's Join, Cut or Intersect changed every body
of the active component it met, shown or hidden: a hidden coincident copy was
joined in and disappeared. Where some bodies of the active component are
hidden, the shown ones become the feature's participants, kept with it, so
showing or hiding bodies later doesn't change the model. Explicit targets and
participants, and a face's or a face sketch's own body, still win.
Test: the issue's plate with a hidden copy and a rim joined on.
Main reached the same fix for Cut and Intersect in #3961 (its targets-based
shown_scope in extrude); this one, which also covers Join and keeps the shown
bodies as participants, replaces it. Its test stays.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
A closed path was always followed from the start of its first picked curve,
wherever the profile stood on it. A profile drawn at the middle of a line was
then carried round the path standing off it by the distance between the two
(walls offset, the rounds turned the wrong way, on both kernels). Now the
closed chain begins where the profile's plane crosses it nearest the profile,
the curve there split in two (or at the joint there); open paths and paths
that already start on the profile's plane are unchanged.
Test: a 4 x 3 profile at the middle of the bottom line of a rounded rectangle
swept round it: Pappus volume and the tube within 2 mm of the path.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
Body::mesh / mesh_plan / mesh_of and MeshTolerance (chord, display, display_of, export_of)
replace tessellate, tessellate_with, display_mesh*, display_plan*, reference_display_mesh_angular;
every caller in kernel, doc, engine, io, ui-egui, gpu and the CLI renamed mechanically; the
truck-mesher fallback, mesh_shells*, refined* removed; Body::new orients from the planner;
truck-meshalgo dropped from Cargo.toml with the tests of its hooks. Still to fix: trait imports
in tess/*, splitface/lumps/preview/step_in/boolean_record meshalgo uses, measure.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
After a parameter edit, a feature's stored face point is moved onto the
face its name finds. That used the face's nearest point to the old pick,
which lies on the face's boundary whenever the pick no longer lies on the
face: a shell opened at the end of a bar picked (150,15,10), on the edge
it shares with the bottom face, so truck opened the wrong face and SMLib
refused the pick (#2531).
FaceHit::pick_point keeps the point where it still lies on the face clear
of its edges, and otherwise takes the face's nearest point among points at
least a margin inside its triangles (a few pick tolerances, capped at half
the roomiest triangle's inradius on narrow faces).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
With SOLIDCRAFT_KERNEL=smlib, kernel::measure and measure_mass take volume, area and centroid
from SMLib's Brep::mass_properties (integrated on the exact surfaces, accuracy 1e-8). The mesh
measure is still made, as an independent check. Where SMLib disagrees with it beyond the mesh's
own accuracy (1e-3; tangency-labs/solidcore#384), or can't take the body, the mesh measure
stands and the measurement says why. BodyMeasure and MassMeasure carry `measured_by` (smlib |
mesh) and `notes`, and inspect.measure shows both. The box and topology counts stay the mesh's.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A new crate (L1, only the kernel uses it) builds tangency-labs/smlib's SMLib,
SM_API and C API with the cc crate when its `native` feature is on, from the
commit in crates/smlib/SMLIB_REV (scripts/fetch-smlib.sh fetches just those
sources). The kernel's `smlib` feature turns it on. Without it nothing C++
is built and every call returns NotBuilt, so workspace builds need no C++
toolchain.
unsafe is confined to src/ffi.rs. The wrapper owns handles, maps statuses to
errors, checks the C API version, and sends SMLib's per-call log to the log
crate. Crash reports note the native kernel call in flight.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Evaluation and placement never read appearances, yet an appearance edit
re-evaluated the model and placed every occurrence again. A whole-document
proof that only appearances changed now takes the existing render-only refresh,
which keeps the model and retargets the world-placement cache.
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Sketch Transform: scale, turn and move sketch entities in one command and one undo
sketch.transform scales about a centre, turns about it, then moves; the window and its
handles for existing sketch geometry build on it.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Sketch Transform window: one box with handles to scale, move and turn what is picked
Select curves and points in a sketch and press G (or Transform in the Modify panel or the
context menu): the picks get a box with a handle at each corner to scale (the opposite corner
stays), the box to move and a knob above it to turn (Shift snaps to 15 degrees). Position,
Width, Height, Scale and Angle in the window are the same values, to type exactly; OK applies
it as one step.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Move the new message to a pending locale file
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Sketch Transform: follow the sketch field of Sel::SketchCurve
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Nathalie Schönwetter <nathalie@cfw-ag.ch>
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Each command that names a body (appearance, material, move, ...) mapped it to
its component's own name by working out every placed body's world name and
frame, so a command on a large assembly cost a walk of the whole design. The
list is now kept with the world-placement cache while it is current.
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Naming a placed body scanned every occurrence and body of the design, so the
world state and every caller naming all placed bodies grew with bodies times
design size. WorldNames indexes the design once and names each body in time
proportional to its occurrence path; one naming routine serves both it and the
single-body scan. Names are unchanged (a test compares them with the scanning
implementation).
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Move the design-link path helpers into one module
`component_link.rs`'s path rules for links to other design files (base_dir,
absolute, relative, stored, resolve, rebased) move, unchanged, into
`cmd/design_link.rs` with their test, so other kinds of link (#3891's drawing
files, linked parameters #5354, #5113's extract) share them instead of copying
or re-exporting them. No change in behaviour.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* design_link: keep base_dir and relative private
Only design_link.rs uses them; the module's surface is absolute, stored, resolve and rebased (review on #5420).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* component_link: import Document after the rebase
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Carel Theron <careltheron@Carels-MacBook-Pro.local>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
A cut (or intersect) that names no bodies went through every body it met,
hidden ones too: a body hidden to keep it out of the cut was cut anyway. When
some of the active component's bodies are hidden, the cut now stores the shown
ones as its targets, so the hidden bodies stay as they are, and stay so once
shown again (the model never depends on what is shown). With nothing hidden it
goes through every body it meets, as before.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Canvas to Sketch: trace a canvas image into a sketch on it (#3931)
New command canvas.to_sketch, offered as Canvas to Sketch in the canvas
context menu. It traces the canvas image (automatic Otsu threshold, light
drawings on dark backgrounds inverted) with interpolated marching squares
and Douglas-Peucker, and adds lines and cubic Bezier splines through Insert
SVG's add_geometry to a new sketch on the canvas plane, with the canvas'
width, centre, rotation and flip. Holes stay holes; one undo step.
The image's declared width x height is checked before decoding (at most
40 megapixels) and the decoder runs under image::Limits, since canvases
are capped by file size, not pixel count.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Move the new message to a pending locale file
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #2605
* Insert SVG / DXF: place and scale the drawing before it is added (#2605, #3443)
After the file is picked, an Insert SVG (or DXF) window sets the
drawing's X, Y offset and scale, with a live preview; OK adds it in one
step and Cancel adds nothing. The insert commands already took `at`
and `scale`; the window is what was missing.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Insert scenario: the picked drawing goes through the placement window (#2605)
`sketch_toolbar_imports_use_file_picker` expected the SVG added as soon as
it was picked; it now checks the placement window first and adds it with
OK.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Insert SVG / DXF: a size in millimetres, an angle, and placement by the drawing's centre
sketch.insert_svg and sketch.insert_dxf take width or height (mm, aspect kept, winning over
scale), angle (degrees) and align (origin or center). The new sketch.drawing_bounds reads a
file's own size without inserting it.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Insert SVG / DXF window: Width, Height and Angle, placed by the drawing's middle
Width and Height in millimetres follow the scale (aspect kept); Angle turns the drawing
about its middle, where X and Y now put it. Uses sketch.drawing_bounds for its own size.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Insert SVG / DXF: handles in the viewport to scale, move and turn the drawing
The preview gets its box with a handle at each corner (scales about the opposite corner,
aspect kept), the box itself (moves) and a knob above it (turns, Shift snaps to 15 degrees).
They edit the same X, Y, Scale and Angle the window shows.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Insert handles: the move that comes with the release counts
A quick drag could stop short of the pointer's last position because the final move arrives
in the same frame as the release.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Insert SVG / DXF: the Drawing Size command's label in the catalogs
`sketch.drawing_bounds` came without a catalog entry, which the i18n
test requires (and the complete ja and zh catalogs with it).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Move the new messages to a pending locale file
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Phanoob <phanoob@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: Nathalie Schönwetter <nathalie@cfw-ag.ch>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #2113
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Crash reports: capture native crashes on macOS (#2113)
A signal handler for SIGSEGV, SIGBUS, SIGILL, SIGFPE, SIGTRAP and SIGABRT
writes the same <journal>.native.json as the Windows exception filter: the
signal, the faulting module and offset, the thread and a frame-pointer walk.
The next start reports it instead of "an unclean exit". The signal then goes
on to the previous handler or the default action, so macOS still writes its
own crash report.
native_crash_macos.rs joins the crash-safety skill's list of files that may
use unsafe (no safe API can catch these signals).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #5641
* Cone primitive: solid.cone with base and top radius (#5641)
A cone or truncated cone placed like the cylinder: base centre, axis,
base radius (or diameter), top radius (0, the default, is a full cone)
and height, with the new body / join / cut / intersect choice. It is
built from what the kernel already exposes, a revolve of its half
section about +Z through the origin, moved into place. Toolbar entry
after Torus, a Cone dialog that also places it on a picked face, Edit
Feature, a timeline icon, pending UI strings and attribution, and one
pending design-format change.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Add Open in Slicer for the selected bodies (#2595)
One command saves the selected bodies as a 3MF in millimetres (an STL if the 3MF can not be written) and opens it in the last slicer used. It is on the File menu, the Mesh tab and the body right-click menu. The first time, or when that slicer is gone, it asks which one with the same list Save as mesh uses. The Save as mesh dialog is unchanged.
* Send slicer files to a private per-user folder (#2595)
Files sent to a slicer used to go to a shared folder in the temp directory. They now go to the user cache folder (mode 0700 on Unix), under a name that stays the same for the same design and bodies, so sending again replaces the file and the slicer can reload it. The file is written to a temporary name and renamed into place. If the name can not be replaced, as on Windows while the slicer holds the file open, the copy gets a number and the status line says so. Files older than seven days are deleted at startup. The first send tells the user that sending again replaces the open file, and so does the tooltip of Open in Slicer. Send to slicer in Save as mesh uses the same path.
* Open files in a running slicer (#2595)
PrusaSlicer, SuperSlicer, Bambu Studio and Cura are started with --single-instance, so a slicer that is already open loads the file instead of opening a second window. OrcaSlicer has no such flag and is left alone, and macOS bundles are single-instance already. PrusaSlicer 3.0 ships a launcher entry that already carries --single-instance-on-url; it keeps that one and never gets a second flag. It is a preference, on by default, and scripts can pass single_instance. Preferences also gets a button to forget the slicer Open in Slicer remembers.
* List slicers the desktop entries say open 3MF or STL (#2595)
On Linux the scan of desktop entries now also lists a program that claims 3MF or STL in MimeType, even when it is not in our table of known slicers. The table still supplies names, ids, icons and flags for the ones it knows. Entries marked NoDisplay or Hidden are skipped, and so are terminal programs and SolidCraft itself. The existing size and count limits stay. The Windows scan now looks inside a Prusa3D folder, where PrusaSlicer installs itself.
* Only start slicers the user can see or chose (#2595)
file.save_mesh took a slicer parameter that could be any executable path, so a script or an MCP client could run any program. The slicer now has to be one of the detected slicers (by id or name) or a program the user already added under Custom, which the app hands to the engine from its settings. The same rule holds for file.open_in_slicer. The agent chat already asked before any file command; its question now also names the slicer.
* Review fixes for Open in Slicer (#2595)
The file name hash keeps all 64 bits instead of 32. When Open in Slicer has to fall back to an STL, the status line now says so. The engine test that sets the chosen programs clears them again. The unused "could not make the folder" message is gone from the catalogs, and the docs say plainly that finding slicers by file type is Linux only.
* Keep unsaved designs apart and hide Open in Slicer in the browser (#2595)
Two unsaved designs with the same name and body names got the same file in the slicer folder. Every document now has a uid that is new for each New, Open and Recover and stays the same for the life of the document, and the file name uses it (with the process id) until the design has a path. At the first Save As the name changes to the path-based one, so the slicer gets one new file; the old one goes with the seven-day sweep.
The browser can not start a program, so Open in Slicer is now disabled there: the engine command reports why, the File menu item and the body and component right-click items are greyed, and starting it anyway says so on the status line instead of opening a dialog. The Save as mesh dialog keeps its browser guard for the open flow too.
* Put the Session doc comment back on Session (#2595)
The new NEXT_UID static had landed between the doc comment and the struct it describes.
* List every install of a slicer, and test the first Save As (#2595)
Detection kept one entry per known slicer, so a system PrusaSlicer 2.9 and a Flatpak 3.0 beta showed up as one. Every distinct install is listed now. The same program found twice, through a desktop entry and through PATH, is still one. When a slicer has several installs, each gets an id made from where it was found (prusa#comprusa3dprusaslicer) that stays the same on every run, and a name worked out from its command and location without running anything: PrusaSlicer (system), PrusaSlicer (Flatpak, beta), PrusaSlicer (AppImage). A lone install keeps its plain id and name. The plain id or name still picks the first install, so a remembered "prusa" keeps working. Single-instance flags and the other per-slicer behaviour go by the id without the install part.
Also a test that the first Save As changes the file name once and later sends keep the name that comes from the saved path.
* Start PrusaSlicer 3.0 first and send the file once it is ready (#2595)
PrusaSlicer 3.0 starts through slic3r-app-launcher, which ignores a file given at a cold start whatever the flag, and loads it over D-Bus when an instance is already running. A small table in slicers.rs names such slicers by their command; today it holds that launcher, so PrusaSlicer 2.9 and OrcaSlicer are untouched. Ready means a name starting with com.prusa3d.prusaslicer.BroadcastListener. is on the session bus, read from busctl --user list with no new dependency. If busctl is missing or fails, nobody waits and the file is sent as before.
When the slicer is not ready, Open in Slicer starts it without the file and looks every 200 ms for up to 10 seconds. The wait runs on another thread, so the window stays live, and the status line says Starting PrusaSlicer. Once the name appears the file is sent with the same arguments as before. If the limit passes, the status line says the slicer did not respond, that the file is already saved, and to send again. A second click during the wait only repeats the Starting line, so there is one launch and one send. Scripts calling file.open_in_slicer wait inside the command by default, or pass wait: return or no.
* Always show the slicer picker for Open in Slicer (#2595)
File > Open in Slicer, the Mesh tab entry and the right-click entry now always open the picker, with the slicer used last time pre-selected, so the usual case is one click or Enter. Scripts and file.open_in_slicer with a slicer still send without a dialog. The preference button that forgot the remembered slicer is gone: it could no longer make anything ask again, and it did not clear the pre-selection either. The guide says how it works now.
* Leave Bambu Studio out of the single-instance list (#2595)
Open files in a running slicer now adds --single-instance for PrusaSlicer, SuperSlicer and Cura only. Bambu Studio is started as it is, so it may open a second window. A test pins that, for the detected slicer and for one the user picked as a custom program. The guide and the preference tooltip no longer name Bambu Studio as getting the flag.
* Sort the English catalog and leave features.md to the generator (#2595)
cargo xtask lists wanted one message moved in en.json after the rebase. docs/features.md is written by the Generated files workflow on main, so the row I had added by hand is gone from this branch; the workflow adds Open in Slicer when it lands.
* Drop the unused folder message from the Vietnamese catalog (#2595)
Vietnamese arrived on main after I removed ui.save_mesh_temp_failed from the other catalogs, so the check that every translated id exists in English failed on it. Nothing uses the message any more.
* Say so when a started slicer can not be found again (#2595)
After Open in Slicer had started a slicer on its own, a failure to look it up again to send the file just returned, so the status line stayed on Starting and then nothing. It now says the slicer was started, that it can not be found to send the file, and where the file is saved. A test covers it.
* Say why a failed busctl ends the wait (#2595)
If busctl fails partway through a wait, the wait stops and the file is sent, the same as when busctl can not be run at all. That is on purpose: a file sent too early is dropped quietly and costs one more send. A comment in wait_for_ready says so.
* Keep the readiness wait inside its limit (#2595)
wait_until asked the probe before checking the deadline, including right after a sleep, so a yes could be accepted after the limit, and busctl ran with no timeout, so one look could outlast the whole wait. The deadline is checked first now, the probe is told how much time is left, and busctl is given at most two seconds (less near the end of a wait) and is killed after that. A hung busctl counts as not telling, which sends the file as before. This covers the first look on the UI thread too. Tests cover a slow probe, the shrinking time left, and a fake busctl that hangs, answers and fails.
* Send the file that was already written once the slicer is ready (#2595)
When the wait for a started slicer ended, the UI ran file.open_in_slicer a second time. That exported the design again on the UI thread, from whatever the session looked like by then, and could write a numbered copy while the timeout message still named the first file. The wait now keeps the slicer it found and the answer of the first call, and opens the file that was written. A test changes the design during the wait and shows the same file is sent, is not written again, no command runs, and no second file appears.
* Send with the single-instance flag after starting a slicer (#2595)
After Open in Slicer has started a launcher that needs a start first, the file has to reach the instance that is now running, so the send that follows a start carries --single-instance whatever the preference says. A normal send, to a slicer that was already up, still follows the preference. A comment in both places says why. The test uses a plain launcher command with the preference off: the normal send has no flag and the send after a start has it.
* Find the remembered slicer again after an uninstall (#2595)
With two installs the remembered key is prusa#prusaslicer. Remove the other install and the lone one is plain prusa, which matched neither the exact key nor the plain-key fallback, so the picker fell back to the first slicer in the list, maybe a different one. The key is now also matched by the part before the #, so the same slicer is pre-selected. A test covers the lone install, a plain key with two installs, an exact key, and that another slicer is never picked.
* Say a second click did not send anything while a slicer starts (#2595)
While a started slicer is being waited for, another click showed Starting <the first slicer> even when it had picked another slicer or other bodies. It now says it is still waiting for that slicer and that nothing else was sent. The test checks the wording and that it names the slicer being waited for.
* Label macOS installs by their application (#2595)
An open -a command resolved its program to /usr/bin/open, so every application on a Mac was labelled system. Labels for open commands now come from the .app path: /Applications is system and a folder under home is shown as ~/Applications. A test with two PrusaSlicer.app bundles and a made-up home checks both labels and that the ids differ.
* Pick the same place for a program found twice every time (#2595)
When two desktop files, or a desktop file and PATH, pointed at one program, the first one read was kept and its file name went into the id, so the ids could change with the order the folders were read in even though nothing was installed or removed. The place that sorts first now speaks for the program. A test with two aliases and a second install lists them with the folders in both orders and gets the same ids and commands.
* Treat flatpak run spelled two ways as one install (#2595)
flatpak run ... and /path/to/flatpak run ... with the same arguments had different install keys, so one invocation could be listed twice. The launcher is now compared by its file name and the arguments are kept, so both give the same key, while a different branch is still its own install. The test uses a real launcher file so the full-path entry is not skipped as stale.
* Say plainly that a late yes is accepted on purpose (#2595)
The comment on wait_until said a slow probe could not accept a yes that came too late. That was not what the code does: no probe is started after the limit, but one already running may finish and its yes is taken, because the file should still go. The comment now says so, with the bound: the limit plus that last probe, which in production is given the time left and so ends by the limit. A test has a probe that runs past the limit and says yes, and checks it is accepted and the wait stays within limit plus the probe time, and that a probe that says no is not followed by another.
* Give reading busctl the same deadline as running it (#2595)
After busctl exited, the output was read with a join that could wait forever if a process it left behind kept the pipe open. The reader now hands the text back over a channel and the wait uses the time that is left of the same limit, and gives up with nothing otherwise. The polling sleep no longer overshoots the time left either. A test uses a fake busctl that backgrounds a sleep with its output inherited and exits at once: the call returns within its limit.
* Tell two different flatpak launchers apart (#2595)
Comparing only the file name of the launcher made /opt/tool-a/flatpak run ... and /usr/bin/flatpak run ... with the same arguments one install even when they are different programs. The launcher is now found the way any program is, through PATH and with links followed, and its name stands in only where it can not be found. The test has flatpak on PATH and the same file by its path as one install, a different executable of the same name as a second, a different branch as a third, and the fallback when there is no PATH.
* Keep waiting when busctl is slow, send only when it is missing or fails (#2595)
Since the busctl timeout, a slow busctl came back as "can not tell", and that was read as send now. One slow look, likely just when a cold PrusaSlicer 3.0 is starting under load, ended the wait and sent the file early, which gets dropped. The look now says why it has nothing: slow means not up yet, so the wait goes on to its limit and then reports that the slicer did not respond; a missing or failing busctl still means it can not be told and the file is sent. The comments name only those two cases. Tests use fake busctl programs: one that hangs keeps the wait going to the limit and times out, a missing one sends at once, one that says not up and then fails sends, and one that names the slicer is ready.
* Do not open an empty path when the answer had no file (#2595)
If the answer kept for a started slicer had no path, the send ran open with an empty string. The tick now says there is no file to send and starts nothing. The test gives a wait with no path, checks the error line, and that the fake slicer was never run.
* Drop the unused folder message from the Danish catalog (#2595)
Danish arrived on main with ui.save_mesh_temp_failed, which this branch removed from English because nothing uses it any more, so the check that every translated id exists in English failed. The entry is gone from the Danish catalog too.
* Always start the 3.0 launcher with the single-instance flag (#2595)
A hand run showed that starting the PrusaSlicer 3.0 launcher with no file while a 3.0 is already running forwards to it and exits when the flag is there, but opens a second full window when it is not. A slow first look at the bus can start the launcher twice, and with the preference off the flag was stripped. A slicer that has to be started first now keeps the flag on that start whatever the preference says, the same reasoning as the send after a start; when nothing runs the flag does no harm. A normal send with the preference off still has none. The test covers the launcher entry, a bare launcher command, a normal send and a slicer that is not on the table.
* Swap --single-instance-on-url where it does not hand the file over (#2595)
A hand run on the PrusaSlicer 2.9.6 Flatpak showed that its entry's --single-instance-on-url does not forward a file to the running instance: every send opened a new one, three after a cold start and two sends. With plain --single-instance the second process finds the first, forwards, and exits. So when a command carries --single-instance-on-url and the slicer is not on the wait table, that is, not the 3.0 launcher, it is replaced by --single-instance, with the file markers handled as before, when the preference is on, and stripped when it is off. On the 3.0 launcher the flag does forward and stays. The comment on the rule says why. A test uses the real 2.9.6 and 3.0 Flatpak command lines.
* Cut long slicer names to fit the picker (#2595)
With installs listed on their own, a name like PrusaSlicer (Flatpak, master) is wider than its row. The list painted it with no limit, so it ran out of the popup, and the closed selector wrapped it onto a second line. The list now lays the name out on one line that ends in an ellipsis when it does not fit, the selector truncates, and the full name is in the tooltip when it was cut (for a program the user added, ahead of the delete hint). A test checks that a long name is cut to one line within the width and a short one is left alone.
* Keep the 3.0 launcher's flag on a send whatever the preference says (#2595)
A hand run with the single-instance preference off showed the 3.0 launcher needs its flag on a send too, not only on a start: a cold start with a file and no flag loaded nothing, and a send to a running 3.0 left a launcher process that never forwarded. A slicer on the wait table now gets the flag on every launch, as it already did when started alone. The doc comment says why. The preference text, in English, Japanese and Chinese, and the guide now say that PrusaSlicer 3.0 is the exception to turning this off. The tests that took the flag away with the preference off now expect it, for the launcher entry, a bare launcher command and the 3.0 Flatpak line; the test of the send in the UI checks the first send carries it.
* Keep the install-flag swap to PrusaSlicer, found by what it is (#2595)
The swap of --single-instance-on-url for --single-instance ran for any program whose command had the flag, so another program with that flag would have been rewritten. It is now a PrusaSlicer rule: it applies to a slicer recognised as PrusaSlicer by its identity, its id or, for a program the user picked, the name it goes by, never by a version number. The single-instance table uses the same identity check. A test keeps the flag of a program that is not PrusaSlicer, strips it when the preference is off, and swaps it for a picked program named PrusaSlicer.
* Do not promise a hard bound in the wait comment (#2595)
The comment on wait_until said the production probe ends by the limit. Its clock starts after the process is spawned, and killing and reaping the process and scheduling are not bounded by it, so it is a polling and read budget with process overhead on top. The comment says that. Comment only.
* Tell PrusaSlicer 2 from 3 by the installed version (#2595)
PrusaSlicer 2 and 3 need different handling, and the rules had to guess from the command line. Each install of PrusaSlicer now carries its major version, read when it is detected from the release at the top of its appstream metadata and never by running the program: a Flatpak's own files (the branch the command names, else the current one), or the metainfo file beside a desktop entry. PrusaSlicer older than 3 is sent the file with --single-instance in place of --single-instance-on-url, which does not hand a file over there, and is not waited for. PrusaSlicer 3 and newer keeps the launcher's flag, is started on its own, waited for, and sent the file. When the version can not be read, the command decides as before: the slic3r-app-launcher launcher counts as 3, and any other entry is left as it is. A program that is not PrusaSlicer is untouched whatever its flags. Tests use metadata fixtures, no Flatpak: 2.9.6, 3.0.0-alpha10, a branch that is not installed, a system package, an unreadable version with and without the launcher, and a non-PrusaSlicer program with the same flag.
* Make the busctl wait tests steady under load (#2595)
One of them failed once in a full run at its first assertion and passed alone. A script that has only just been written can fail to start (text file busy) while another test forks, and that reads as a busctl that is missing. The fake programs are now started once, patiently, with a flag they answer at once, before a test relies on them; a hanging one uses exec so it is killed cleanly. The time bounds that could trip on a busy machine are several seconds now, and the checks are on outcomes: not ready and keeps waiting, send now, and the number of looks. Thirty runs alone, thirty of the whole slicers filter and thirty of the busctl tests under eight busy loops all pass.
* Say what the busctl reader thread leaves behind (#2595)
The thread that reads busctl output is left to end when the pipe closes. A busctl that answered but left a process holding its stdout reads as slow, and every poll of such a bus can leave one blocked reader behind until that process lets go. A comment next to the thread says so. Comment only.
* Make Save as mesh a plain export (#2595)
Save as mesh asked for the bodies and the format, and could also send the file to a slicer with a checkbox and a slicer list. Sending now has its own command, so the checkbox, the list and the Send label are gone from this dialog: bodies, format, a file dialog, Save. The two settings that only the checkbox used, save_mesh_send and save_mesh_slicer, are no longer kept; a settings file that still has them loads, and they are ignored. The strings only they used are gone from the catalogs. The slicer list stays in the dialog of Open in Slicer. file.save_mesh keeps its slicer parameter for scripts. The guide describes the two as separate.
* Rename Open in Slicer to Send to Slicer (#2595)
The command sends a file to a slicer rather than opening one, and a later Send to App can share the name. File menu, Mesh tab, right-click menus, the dialog button, status lines, the guide and the English, Japanese and Chinese strings now say Send to Slicer, and the command id file.open_in_slicer is file.send_to_slicer. It is new in this change, so there is no alias. The remembered slicer is stored as send_slicer, and the question the agent chat asks says send to. Module and type names stay as they are.
* Put the send targets in one table and one send pipeline (#2595)
The known slicers, the list of slicers with a single-instance flag and the rule for slicers that must be started and waited for were three separate things. They are one table of targets now: id, label, kind, names and program files, accepted formats and the default, how the file is handed over, the single-instance flag, the version from which PrusaSlicer's on-url flag hands a file over, and the wait-for-ready rule. Programs that are not in the table are slicers with the same defaults. The kind is slicer, the only one so far; its comment says it is where a later Send to App would plug in. The send itself is one function: write the bodies, find the target, start it and wait if its rule says so, hand the file over, report. Detection and resolution take a kind. Nothing changes for what already worked.
file.save_mesh keeps its slicer parameter, now through the same function, with its export arguments and result unchanged: a cold PrusaSlicer 3 is started and waited for before the file goes, and it accepts the program path of a detected slicer as file.slicers lists it (file.slicers gives it as program). A path is accepted only when it is the program of exactly one detected target, and that target's own command and arguments run; a launcher several entries share, such as /usr/bin/flatpak, is refused as ambiguous, and any path nobody listed or chose is refused. The parameter and the code say it may be deprecated later in favour of file.send_to_slicer or a Send to App workflow, which is a possibility and not a plan.
Tests go through file.save_mesh itself for the two reported failures, a listed AppImage path and a cold PrusaSlicer 3 that is waited for, with the slicers and the busctl made up; and they check that the result and the file are what an export without a slicer gives, and that a path that is not listed, or is shared by two entries, writes nothing. The pipeline has its own tests: a cold launcher waited for, one already up, wait return, and one that never comes up. A test of save_mesh that shared a file name with another is given its own.
* Keep an AppImage's id through an upgrade (#2595)
When a slicer has several installs, each gets an id made from where it was found. For an AppImage that was its file name, which carries the version, so upgrading it changed the id and the remembered choice missed. The id is now made of the slicer's id, the fact that it is an AppImage and a short hash of its folder, so a new version that replaces the old one in the same folder keeps the id, and the same AppImage in another folder is its own install. Two versions kept side by side in one folder are two installs: while both are there, their file names are added to their ids to tell them apart.
A remembered id is found again only when it names exactly one install. An id that was one AppImage and is now two versions, or a plain id that is now several installs, is treated as not remembered, so the picker starts from the first entry as on a first run and does not quietly pick another install; a single install left of the same slicer is still found, as before. Installs that are not AppImages are told apart as before. An id from before this change no longer matches. Tests cover an upgrade, two versions side by side, a second folder, and the picker's side of each case.
* Add Open with EasyPrint to Send to Slicer
EasyPrint is Printables' slicer in the browser. It's a plain text row in
the Send to Slicer dialog, backed by a new file.open_in_easyprint
command. The command exports the bodies as a 3MF (or STL), hands them to
the host to upload to slicer.printables.com/import, and the app opens the
link that comes back. The desktop app uploads with ureq and the browser
build with fetch, so this is the one send target that works on the web.
The model leaves the machine, so the command refuses without
consent: true, the dialog asks once and remembers, and an AI agent's
request asks first. A model over 100 MB is refused before anything is
sent, and a failed upload shows as an error with the reason.
The chat's privacy note said SolidCraft sends nothing anywhere, which
isn't true any more, so it now says that about the chat. New strings are
in every catalog.
* Place Send to Slicer on the Insert Files panel
* claim: #6070
* Sketch: a changed length dimension keeps its start point, so a side grows from its first corner (#6070)
Changing a dimension's value re-solved its sketch as the smallest move from
the stored positions, which splits the change between both ends: a
rectangle side set from 40 to 60 mm grew 10 mm each way. parameters.change
now first solves a sketch whose length dimension (distance, horizontal or
vertical distance, line length) the parameter drives with that
dimension's first point held, and stores the result, so evaluation has
nothing left to move. Where holding it can't solve (a symmetry moves both
ends), evaluation solves as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #5099
* Browser: a feature's eye shows or hides the bodies it made (#5099)
A row in the Browser's Features folder has an eye when the feature made
bodies that are in the design now (a patch, a box, a pattern's copies;
not a fillet, which changes bodies). It runs browser.visibility with the
new features: [id or name] (and path: for one placement of a component
placed more than once), which hides or shows those bodies.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
A path a design names (a linked design, a sketch text's font file) now
goes through one rule before any file call: a network location is
reached only once its server is allowed, a device path never. Update
Links and Open Linked Design ask first (Allow once / Always allow this
server / Cancel); Preferences > Design lists the allowed servers and
can allow every network location. component.links reports such a
link's found as unknown with a reason, without looking for it.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6724
* Extrude: the picked region is the one extruded again (#6724)
Since #5530 (#5302) every index or point pick grew to the whole drawn
profile that reference geometry cuts, so a lens or crescent clicked in
Extrude, where the face's projected outline cuts a circle, extruded the
whole circle while the dialog highlighted and counted one region.
Dialogs now send exact_regions: true with their profile picks, and the
command keeps each pick to the region it names. Picks without the flag
(scripts, agents, the CLI) still take the whole drawn profile (#5302).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #4784
* Part properties: one table of keys, each with its scope, check and label (#4784)
SolidCraft's part-property keys (project, part number, revision, author,
organization, description, licence) were declared once but listed again
by hand in each command, error, dialog and window. They are now one
table, metadata::KEYS: each row has the key, where it may be set
(Scope: the design, a component or both), how its value is checked and
the message id of its label. A new key is one row.
Metadata::set is told whose metadata it changes (Owner::Design or
Owner::Component), and a key is taken where its scope covers that
owner. is_well_known, both set commands, document.metadata,
component.metadata, the refusals, the Design Properties dialog and the
Bill of Materials window read the table; the hand-written lists are
gone (WELL_KNOWN, the label match whose fallback named any unknown key
"License", the window's three labels). metadata::BOM_KEYS names, in
column order, the keys a bill of materials lists for each part:
component.metadata returns them, component.metadata.set takes each as a
parameter of its own and the window edits them; a test keeps each one a
row of the table that a component takes. Free properties use the keys'
text rule (metadata::check_text) instead of a copy of it. The params
docs point to document.metadata's properties instead of repeating the
keys.
Every key accepted before still is, on the design and on a component.
Two things change:
- a refused key or a full metadata on a component says "part property"
("`bogus` is not a part property: …", "part properties are limited
to …"), not "design property";
- changing the design's own properties no longer evaluates the model.
The fields that change no geometry are named once,
Document::with_part_properties_of: the design's metadata, and each
component's metadata and free properties. It compares them first and
copies the design only when one differs, as before.
The shortcut is for a session's own edits only. A command that gives
the session another design (doc.open, file.new, doc.recover: through
Session::replace_design, which now counts them) is refreshed in full,
however little the new design differs from the one before, so its
joints are solved and its occurrence state pruned. Before, opening a
design that differed from the open one only in render settings or
component properties skipped that; with the design's properties in the
list it would have for two revisions of one part too.
Tests: the table (one row per key, the dialog's order); the bill of
materials' keys (rows a component takes, in column order); each scope
on each owner, and refusals that name the owner (the empty key, an
unknown key, a 256-byte key shown cut); the text check at 4096 bytes,
line breaks, tabs and control characters; hostile keys and values
refused without a change; only-part-property changes in each scope,
and changes beside them (units, a component's name, an added, removed
or swapped component); document.metadata.set, remove, undo and redo
evaluate nothing; opening a revision that differs only in its author
solves its joint; the component wording, the shortcuts and the limits;
the dialog's and the window's labels from the table.
What the tests can't reach: every row is Scope::Both, so a known key
refused for its owner (the wrong-owner branch of check) can't happen
yet. It becomes live with the first single-scope row, bom_type, a
component-only key.
Left for later (not this topic):
- Metadata::others() ignores scope, so a component-only key stored on
the design would be neither a dialog field nor listed under other
tools' data. It matters from the first single-scope key (bom_type).
- assembly.bom's rows, its CSV columns and the window's grid headers
still name the three keys by hand; the bill of materials module's
rewrite will read BOM_KEYS.
- The bill of materials types (P1, #5107, into drawings) still use
WELL_KNOWN and the two-argument set: once this is on main, bom_type
is rebuilt on it as one KEYS row with Scope::Component, set through
Owner::Component.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #5681
* sketch: exact circular arcs on drawn 3D wires (#5681)
Add WireArc (centre, unit normal, radius, start/end) as an optional analytic
form on drawn 3D sketch wires, with arc_from_3_points, arc_sweep and
sagitta-bounded arc_polyline; add_drawn_arc_in stores the arc, its three
defining fit points and its samples; move_drawn_point re-derives the arc
atomically and refuses collinear points; validate_wires checks saved arcs.
* engine,ui: sketch.arc3d exact 3D arc command (#5681)
sketch.arc3d draws an exact circular arc through three world points in a 3D
sketch, stored analytically beside its fit points and samples; sketch.move3d
rebuilds it, sketch.inspect reports centre/radius/sweep; placement mapping
(map_wire, now shared with the engine's world state) transforms the arc.
One pending design-format file records the new field. The viewport's 3-Point
Arc tool draws a 3D arc when clicked off the sketch plane, with a live arc
preview; the SKETCH panel offers sketch.arc3d.
* ui,engine: 3D Arc button starts an interactive tool (#5681)
sketch.arc3d now maps to a Draw(3) tool handled by sketch3d: three world clicks (start, end, through - same order as the 2D arc tool) run the command, with the live arc preview and snapping. The command is only enabled while a 3D sketch is open, so the toolbar never offers a tool that could only fail. Locale labels for the command.
* ui: cargo fmt
---------
Co-authored-by: RayGalt <RayGalt@pm.me>
* claim: #3133
* Apply complete feature transactions off the window thread
Evaluate dependent history and prepare reference and GPU display caches before accepting a guarded result. Preserve the evaluated original model for safe editor cancellation and journal only accepted commands.
* fix(ui): preserve original marker across sketch-to-feature edits
* test(ui): verify edit-sketch cleanup and guard Unix link fixture
* test(ui): fix texture disposal and unreachable assertion in feature tests
* fix(build): compile CLI link inspection only on Unix
While an agent's batch computes off the window thread (#1989), the chip reads
N/M · <command>. It is centred on the navigation bar, just above it, and moves up
past any toast or panel it would cover.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Axes and points from circular edges and round faces
In 3D, a round edge or face stands for its circle wherever a command
takes an axis or a point.
Revolve, Surface Revolve, both Circular Pattern dialogs, Plane at Angle
and Move -> Rotate take a circular edge (through its centre, along its
normal) or a cylinder, cone or torus face (its axis). The features keep
the pick as a model reference, so they follow the model when a parameter
moves it. Straight edges work as before; flat faces are refused.
Every 3D point input takes a circle's centre: construction points (which
follow the circle), To Object, patch points, hole placement, and Move's
pivot and points. Hovering shows the axis as a dashed construction line
or the centre as a star, and the dialog's chip names what the pick
stands for ("centre of edge 10", "axis of face 3").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Format the round-pick hover check
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Selection chips: name a round pick as a circle centre or axis
The chip has room for little more than the body and a word or two:
"Shaft · circle centre", "Shaft · circle axis", "Shaft · face 2 axis",
and "Shaft · point" for a point of the model.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Move: a circle's centre in a placed component is where the component shows it
Move's pivot and points read a picked circle from the model in its
component's own frame, while the pick is in the world. They now read it
from the world state (and, editing a Move, from the state before it,
placed the same way), as the viewport and the other round picks do.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Plane at Angle on a planar face about a model edge: test that it follows both
Upstream #1956 made a planar face a base for Plane at Angle; this branch makes a model edge an
axis. The rebase keeps both in one PlaneRef::AtAngle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Frames: a Weldments ribbon tab (#4003)
- WELDMENTS joins the ribbon after SHEET METAL and is built the same way:
Sketch (New Sketch), Create (Frame Member) and Configure (Parameters,
Configurations). Frame Member's home moves there from MODEL > Create.
- Always shown, as a frame starts from a sketch of its lines. It selects
itself and takes the contextual style when the selected body (or the last
body of the active component) is a frame member; sheet metal comes first.
- It uses the default accent until the palette has a colour for it.
- The tab label is in every catalog; docs/ribbon-layout.md, docs/frames.md
and the tab list in docs/control-protocol.md follow.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Frames: Weldments keeps the ordinary tab look (#4003)
Weldments still selects itself when a frame member is the active body, but
no longer takes the solid contextual fill or the 2 px accent line under the
tab row: selected, it looks like a selected Model tab. Only Sketch and Sheet
Metal (on a sheet body) are contextual.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Patterns: one before the feature it copies follows that feature's parameters (#6726)
A pattern or mirror of features made with the timeline rolled back comes
before its sources and replays them from their definitions. Its
fingerprint chained only the features before it and its own inputs, so a
change of a source's parameter left its result in place: the box grew,
its copy kept the old length, also after rolling forward.
The chain fingerprint of a pattern or mirror of features now also takes
the fingerprint of each feature it replays (and of their sources, for a
pattern of a pattern), wherever they are in the timeline.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Patterns: a test for a later feature taking a deleted source's name (#6726)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Patterns: fingerprint the replayed sources with the document, as fingerprint now takes it (#6726)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6720
* Face pick by point: linear work budget, so bodies with many faces take a sketch (#6720)
A face picked by its point alone charged the whole mesh once per face, and
face_contains scanned every triangle for each candidate. A block with a
modelled thread (about 5 000 faces) went past the 2 000 000 limit. The
triangles are grouped by face once, each face's test reads only its own,
and the budget charges triangles + faces.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #3812
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27
* Sketch Dimension: value box in the design's units (#3812)
A dimension added without a value restated what it measured as
"<value> mm", whatever the design's units. In an inch design the
Dimension tool's value box therefore opened at "25.4 mm" next to a
dimension whose text read 1.000 (inches).
Document::design_length writes a measured length in the design's units
("1 in"), with enough decimals to keep it to the micrometre, so a
dimension that restates the geometry still moves nothing. The Dimension
tool, AutoConstrain's dimensions and Toggle Driven (making a driven
dimension driving) use it. Millimetre designs are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27
* Move the design-units dimension tests into sketch_ux_tests (review)
The #3812 tests go in the existing sketch dimension test file rather than
a new file of their own (AGENTS.md, #3226).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6550
* Crash reports: keep journaling through file.new and doc.open (#6550)
`Session::replace_design` swapped in the fresh session without its
`crash_journal` flag, and the app turns it back on only at its next frame.
So `file.new`/`doc.open` never recorded how they ended, the commands sent
after them in the same frame (a control-channel or MCP batch) were not
journaled, and a crash report then named `file.new` as the command in
flight. `replace_design` now keeps the flag, like the other session-wide
fields it keeps; only the design on screen has it set.
Test: `commands_right_after_a_new_design_are_journaled` (crash_tests.rs).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6917
* Tests: the six timing assertions do not depend on the wall clock (#6917)
Six tests asserted on the wall clock. Their result depended on how loaded
the machine was and not only on the code under test: they passed on an idle
machine and failed when the test binaries ran beside each other, which is how
the suite runs (`cargo xtask test` starts every test binary at once).
CONTRIBUTING.md:196 says it: "Tests run beside each other on a busy machine,
so a test must not depend on wall-clock timing."
The change is confined to the six test files the issue names:
- geom: the tangent chain of a helix is a ratio (750 pieces against 3 000)
instead of a limit of 200 ms.
- io: the placement budget is spent inside the reader, so the clock is gone.
- ui-egui: the classification of many faces is a ratio (900 against 3 600)
instead of a limit of 10 s.
- engine: the clearance measurement drops its 30 s limit; the boolean that
gives up reports itself.
- engine: the fillet beside a modelled thread is a ratio (a 1 mm thread
against an 8 mm one) instead of a limit of 30 s.
- ui-egui: the window frame budget goes from 250 ms to 20 s, the limit #6072
gave its own probe.
The helper is the one #649 wrote, copied into the crates that need it, with
the noise of a run as a parameter.
* claim: #6558
* Shortcuts: Ctrl+Shift+S opens Save As in the workspace (#6558)
The Home page already opened Save As with Ctrl+Shift+S, but the design workspace matched Ctrl+S, so the chord saved over the current file instead of offering another one. The workspace now routes the chord to Save As, and the File menu shows that shortcut next to Save As, taken from the command registry.
* claim: #5679
* Top-level cut and join reach bodies in sub-components (#5679)
An extrude, revolve or press-pull from a sketch on a face of a body in a
component inside the active one now cuts or joins that body, moved or
turned, in its own component, so every placement shows the change. The
automatic operation probes that body where it is shown. A linked part, or
a face on a further placement of a part placed more than once, is refused
with the reason instead of a silent no-op (#5678).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>