A thread of some length ran from "the end of the face nearest the pick", a coin toss for a pick in the middle (rig 602's 4 mm thread meant for the free bottom end ran at the head end, cutting 1.17 mm into the hex), and every thread end at a face end got a one-pitch overrun, which at a shoulder gouged the material past it (ladder 06/004 cut 0.9% of its volume out of the collar). - kernel: material_in_ring, the exact intersection of a body with a ring about a cylinder face's axis, by an SMLib boolean. - doc: a face end is free when no material lies past it, over the span the groove's one-pitch overrun reaches beyond its first pitch, within the radii the groove cuts (a cap, a chamfer the groove runs out through, a counterbore). At a free end the groove runs out as before; at a closed one (a shoulder, a head, a blind hole's bottom) it stops with its widest part clear of it; inside the face it stops square. - doc: a thread of some length starts at the end nearest `from`, else at the face's only free end, else at the end the pick lies within a third of the face of; a pick in the middle of a face whose ends are alike is refused, naming `from`. A length as long as the face runs the whole face. `up_to` a plane or a point's place along the axis. New fields `from`, `up_to` default to none, so saved threads keep their meaning where it was not a coin toss. - engine: solid.thread takes extent (full|length|up_to), from and up_to. - ladder 06/003 (now with `from`), 004 and 007 are graded by volume and centre of mass in closed form (a square stop inside material removes exactly length/P turns, the section being symmetric); rig 602's method says why the thread is at the bottom, tolerance 0.02%. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
29 lines
1.4 KiB
JSON
29 lines
1.4 KiB
JSON
{
|
|
"sources": [],
|
|
"what": "a modelled M10 thread over 15 of the 30 mm from the top end (`from`): it stops square in the middle of the face",
|
|
"source": "analytic",
|
|
"method": "ISO 68-1 basic profile (60 deg, root flat P/4 at d - 5H/4 ... minor d1 = d - 1.0825 P, crest flat P/8): a helical groove of fixed section is a screw motion, so averaged over the turn every meridian half-plane holds the same section and V = 2 pi int int r m(r) dr dz over the stock's section, m the material fraction per pitch; the groove runs out past free ends. ; the thread runs from the top end (z=30, out past it into the air) down to z=15, where it stops square: there the groove's section is symmetric about its centre line, so the sweep's last section cuts behind the stop what it leaves ahead of it, and the stop removes exactly as if the groove ended at z=15: V = pi 5^2 15 + 2 pi int_15^30 int r m(r) dr dz. The centre of mass is on the axis (ten whole turns; the stop's pieces are under 0.02 mm off it) at z = (pi 25 15 x 7.5 + V_threaded x 22.5) / V; the stop's first moment, O(w^2), moves it under 0.002 mm. A pick at z=15 alone would be refused: both ends are free. Tolerance 0.05%: the groove is SMLib's exact screw sweep",
|
|
"body_count": 1,
|
|
"volume_mm3": 2155.220203721,
|
|
"center_of_mass": [
|
|
0,
|
|
0,
|
|
14.300624991390395
|
|
],
|
|
"bbox": {
|
|
"min": [
|
|
-5,
|
|
-5,
|
|
0
|
|
],
|
|
"max": [
|
|
5,
|
|
5,
|
|
30
|
|
]
|
|
},
|
|
"tolerance": {
|
|
"rel": 0.0005
|
|
}
|
|
}
|