Files
solidcraft/crates
cccf8c1ece Snap points: a flat face offers its corners, edge middles and every hole's centre (#11476) (#11477)
* Snap points: a flat face offers its corners, edge middles and every hole's centre (#11476)

A flat face now offers its whole outline as snap points, read from the
exact faces and edges: every corner, the middle of every straight edge
and the centre of every round edge, holes included, as well as the centre
of its area. Corners on a closed circle's seam, or where the kernel split
one circle into pieces, are left out.

snap_points_from gives each point with where it came from (SnapSource):
the face it was picked on, the face's outward normal and a point inside
its edge, so a tool can keep the point by name (joint.create's edge,
corner and on) and turn a frame to the face. SnapPoint itself does not
change, so code that builds one keeps compiling.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Snap points: a round face's end centres say which way their end faces (#11476)

The centres at a cylinder's or cone's two ends now carry a normal in their
SnapSource: the axis pointing out of that end, which is the normal of the
face a hole opens onto or of a pin's end. A joint origin taken from one can
then lie on that face, as the centres a flat face offers already do.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Snap points: a hole centred on its face keeps its own point and rim (#11476)

Snap points were one point when they lay at one place, whatever their kind,
so a hole centred on its face was lost behind the face's centre, and with it
the rim its point keeps. Now only points of one kind are merged: the face's
centre and the hole's centre both stay, and only the hole's has its rim.

SnapSource::normal's doc now says it is also the axis out of a cylinder's or
cone's end.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Snap points: a washer's two rims keep a centre each (#11476)

Centres at one place are one point only when they are on one circle: the
inner and outer rims of a washer face now keep a centre each, with its own
rim, while the pieces the kernel split one circle into are still one point.

SnapSource::normal's doc now says that at a round face's end it is the
axis out of that end of the face, which at a blind hole's bottom points
into the material below, not out of it.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Snap points: rims are told apart by their radii's size, not their place (#11476)

Two centres at one place were one circle when their rims' radii differed by
less than the place's tolerance, which grows with the distance from the
origin: 60 m out, rims of 4 and 4.05 counted as one and one lost its point.
The radii are now compared with a tolerance from the radii themselves.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Snap points: nearby points stay apart far from the origin (#11476)

Points of one kind at one place were merged within a tolerance of 1e-6 of
their distance from the origin, 0.06 mm at 60 m, so two small holes there
whose centres are 0.05 apart lost one centre. Places now use 1e-9 of that
distance (0.06 µm at 60 m): well above the rounding of coordinates and of a
circle fitted to an imported edge, so a point found twice is still one, and
far below any feature. The radii keep their own tolerance.

The merge is its own function, so its test can give it points directly.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Alfonso Tamés <mufufu@Mufufu-MacBook-Pro.local>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-04 18:02:44 +00:00
..