Jackson OurslandandClaude Opus 5.5 ca4f3ed1a0 Book: getting started, sheet metal and import/export get pictures (#10732)
* Book: sketching step by step, with three clips and a numbered screenshot

The sketching page now opens with a first sketch in four steps: start a sketch on the Top
plane, draw a 60 x 40 rectangle and a 12 mm circle with typed values, dimension the circle
until the sketch is fully constrained, and finish. Each step has a short clip, and the last a
screenshot numbering the Sketch tools, a constraint, a dimension, the sketch's state and
Finish Sketch.

doc_shots.py gains what these needed: a setup that runs before recording, so a clip starts
where the last one ended; sketch framing; Enter sent as two input frames; and clips that keep
their pauses (hovering a plane).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Book: the sketching page's general notes get a heading after Step by step

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Book: sketching adds Offset and Trim; the sketching figures again on 0.29.0

Two more clips after the sketching walkthrough: Offset draws the rectangle's outline 4 mm inside
it with one click (Chain), and Trim cuts a notch where a circle crosses the top side. All the
sketching figures are made again on SolidCraft 0.29.0, with the clips keeping a moment on each
result.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Book: solid features step by step, with four clips

The solid features page now opens with the sketch from the sketching page made into an open
box in four steps, each with a short clip: extrude it 12 mm, shell it with the top open,
round its outer top edges, then make it 20 mm tall from the timeline while the shell and the
fillet rebuild. The panel table and what follows get a heading of their own.

doc_shots.py: the feature shots share their steps with the setups that lead up to the next
shot, and fail when a feature on the timeline carries a warning or an error, so no figure
shows one. Shell comes before Fillet for that reason: shelling through the rounds needed the
kernel's boolean retry. trim_idle.py takes --hold, the seconds of each idle stretch to keep
(default 0.1 as before); the doc clips keep 0.8 s, so a reader sees each result. The app gets
up to three minutes to answer on a busy machine.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Book: features add Hole and Circular Pattern; the Parameters dialog, numbered

The features walkthrough gains two steps before the timeline edit: a 4 mm hole on the box's
floor, then Circular Pattern repeating it four times around the tube. The edit at the end now
rebuilds all of it. The parameters page gets a screenshot of the Parameters dialog numbering
apply as you go, user parameters, model parameters by feature, an expression and its value.
The features clips are made again on SolidCraft 0.29.0.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Book: components and joints step by step, with three clips

The components and joints page now opens with a two-leaf hinge in three steps, each with a
short clip: the two bodies made into components from the Bodies folder's menu (the first one
grounded), a revolute joint on their barrel ends with Flip turning Leaf B the right way round,
and a drag that swings Leaf B about the hinge while grounded Leaf A stays put. What follows
gets a heading of its own.

doc_shots.py builds the leaves from commands, with Leaf B lifted and set back so the joint
visibly brings it into place.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Book: assemblies add Drive Joints; the assembly clips again on 0.29.0

A fourth step drives the hinge with Drive Joints: the slider swings Leaf B while a ghost shows
where it started, and OK keeps the new angle. The assembly clips are made again on SolidCraft
0.29.0.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Book: getting started, sheet metal and import/export get pictures

Getting started gains a section on the start page: a numbered screenshot (new design, open,
import, recent, samples, the File menu) and a clip opening a sample from it. Sheet metal opens
with a tray in three steps, each with a clip: a base flange from a sketched rectangle, edge
flanges from two top edges, and the flat pattern with its bends. Import and export opens with
the File menu, numbered.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-05 06:31:44 +00:00
2026-11-03 15:35:34 -05:00
2026-10-11 16:07:46 +08:00

SolidCraft

SolidCraft

An open-source parametric 3D CAD application built in pure Rust.
Sketch, constrain, and build solids with a parametric feature timeline. Change a dimension and watch your model rebuild. Run it on your desktop, in your browser, or let AI agents model through the built-in MCP server.

Download for Windows Download for macOS Download for Linux Get it from the Snap Store Try it in your browser

Website · Download · Try it in the browser · Documentation · CI powered by Blacksmith Discord · SolidCore

CI Latest release Downloads Licence Discord Listed on Remade Stars

tangency-labs%2Fsolidcraft | Trendshift tangency-labs%2Fsolidcraft | Trendshift (Rust)

SolidCraft: model a Raspberry Pi 4 case from an empty design: a sketch dimensioned with parameters, extrude, fillets and shell, a rim rounded in one pick, standoffs patterned on the board's mounting holes, port cut-outs, vent slots, "Pi 4" engraved in a font, a PETG material with its mass in Properties, and a height change in Parameters

A Raspberry Pi 4 case from an empty design: a sketch dimensioned with the board's parameters, extrude, fillet, shell, the rim rounded in one pick, an M2.5 standoff patterned on the 58 × 49 mm hole rectangle, port cut-outs, vent slots, "Pi 4" engraved in DejaVu Sans Bold and a PETG material defined in the design, with its mass in Properties, then height 24 → 32 mm in Parameters and it all rebuilds. 6× playback with the idle pauses cut. Full video, recorded with the demo script.

Download

ARM64 and 32-bit builds, portable zip, .deb, .rpm, Flatpak and the other packages are on the downloads page. The macOS app is signed with a Developer ID and notarized by Apple. The Windows downloads aren't signed yet: choose More info, then Run anyway in SmartScreen. On SolidCraft 0.11 to 0.14, download once by hand; see updating.

What works

Early but usable for simple parts: 75 of 76 public reference parts match their analytic or FreeCAD-computed volume, area, centre of mass and bounding box (oracle); the other is a tracked bug.

  • Sketches and constraints: lines, arcs, splines, text and more, solved by our own constraint solver, with parameter-driven dimensions.
  • Features: extrude, revolve, sweep, loft, fillet, chamfer, shell, draft, holes, threads, patterns, mirror, split and combine on an editable parametric timeline.
  • Parameters and configurations with unit-aware expressions.
  • Assemblies with joints, motion studies, contact sets, interference and mass properties.
  • Sheet metal with flanges, hems, fold/unfold and flat patterns, and plastic enclosure features.
  • Files: STEP, IGES, 3MF, STL, OBJ and glTF in and out where supported, URDF export, .sc designs (.solidcraft files from earlier releases still open).
  • Desktop app, browser app, headless CLI and MCP server, all running the same commands.

The full list is in docs/capabilities.md and docs/features.md; status and plans are in ROADMAP.md. See also what people built, 3D mouse support and the architecture.

Build from source

cargo run --release -p solidcraft -- --sample      # desktop app with a sample part
cargo run --release -p solidcraft-cli -- commands  # the command registry
cargo run --release -p solidcraft-cli -- run examples/bracket.json --out bracket.step
cargo xtask ci                                     # fmt, clippy, tests, icons, assets, layers, wasm

More commands, the Windows cross-build and the browser build are in docs/building.md.

AI agents (MCP)

solidcraft-cli mcp is a Model Context Protocol server. Headless it runs its own design session, or with --connect it drives the running app so you can watch. Claude Code: claude mcp add solidcraft -- solidcraft-cli mcp. If a terminal doesn't find solidcraft-cli (older Windows installers don't put it on PATH), give its full path (by default "C:\\Program Files\\SolidCraft\\solidcraft-cli.exe"). Tools, access rules and an example session: docs/mcp.md.

Scripts

A script is a JSON list of the same commands the UI runs, executed with solidcraft-cli run. Format and example: docs/scripts.md. Pages can also be driven through the browser command API.

Contributing

Help is welcome. CONTRIBUTING.md covers how to build and test, the code map, the clean-room and licence rules, and where help is wanted most. Open work is in GitHub issues; chat is on Discord.

Sponsors

CI powered by Blacksmith

SolidCraft's continuous integration runs on Blacksmith, which sponsors its CI minutes.

Disclaimer

The files in this repository are provided as is, without warranty, liability or indemnity, and Tangency Labs and the contributors accept no responsibility for any harmful or unlawful use of them: read DISCLAIMER.md.

Licence

MIT OR Apache-2.0, at your option. Developed under the clean-room contribution rules; third-party code and assets retain their documented licences and attribution.

SolidCraft is independent. Behaviour is designed from public documentation, general CAD conventions and user feedback. Reference tests use analytic values and open-source tools. SolidCraft is not affiliated with, sponsored by or endorsed by Autodesk, Dassault Systèmes, PTC, Siemens or any other CAD vendor. Fusion, AutoCAD, Inventor, SolidWorks, Onshape, Creo, Blender and Tinkercad are trademarks of their respective owners, named only to describe compatibility (see NOTICE).

S
Description
SolidCraft: an open-source parametric 3D CAD application built in pure Rust. Desktop, web, and automation through MCP.
https://solidcraft.io Readme
501 MiB
0 Stars 1 Watchers 0 Forks
Languages
Rust 97%
Python 2%
WGSL 0.5%
JavaScript 0.3%
Shell 0.1%