Only the ISO metric 60° thread existed. Forms now (crates/doc/src/thread_forms.rs, values and sources in docs/threads.md): ISO metric (ISO 68-1), trapezoidal (ISO 2904 design profile, ISO 2902 sizes), general purpose Acme (ASME B1.5), metric buttress 3°/30° (DIN 513), buttress inch 7°/45° (ASME B1.9 basic profile). Each has its groove as a straight-flanked polygon, its standard sizes (none for ASME buttress), its designations (M10, M16xPh3P1.5, Tr40x14(P7), S20x4, 1/2-10 ACME, 2.5-8 BUTT) and the size that fits a face. The square thread is refused: no current standard defines it. `hand: right | left | both`: a left-handed groove is the screw motion about the reversed axis rising along it; both cuts the two grooves, crossing, in one boolean. `steep_flank` turns a buttress. The design diameters are checked against the published tables (ISO 2904/DIN 103, DIN 513 via IS 4696-3); every form's cut against 2π∫ r w(r) dr per turn to 1e-4 in engine tests and to 1e-4 in ladder 06/011 to 016 (they measure within 5e-7). FeatureKind::Thread holds every option the command has (form, hand, starts, ease_in, ease_out, tip, chamfer_angle, chamfer_depth, steep_flank, all defaulted so saved threads load unchanged); starts, runouts and the chamfered tip are refused as not built yet. suggested_thread_in takes the form. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
89 lines
6.1 KiB
Markdown
89 lines
6.1 KiB
Markdown
# Threads
|
||
|
||
`solid.thread` puts a thread on a cylindrical face: cosmetic (an annotation, `model.threads`
|
||
lists it) or modelled (the groove between the teeth cut into the body along a helix, SMLib's exact
|
||
screw sweep). This page gives the forms, the values each uses and where they come from, and how a
|
||
thread's extent is decided. The code is `crates/doc/src/thread_forms.rs` (forms, sizes,
|
||
designations) and `crates/doc/src/eval_thread.rs` (the thread on its face, the cut).
|
||
|
||
## Forms
|
||
|
||
Every groove is a polygon in an axial half-plane: straight flanks, flat crest and root. Crest and
|
||
root radii (the ISO metric root radius, the buttress root radius R, DIN 405 knuckle and Whitworth
|
||
rounds) are not modelled. External threads are cut from the shaft's surface (a little past it, so
|
||
no skin is left) down to the external thread's minor diameter; internal threads from the hole
|
||
wall out to the internal thread's root. Pitch-diameter allowances and tolerance classes are not
|
||
modelled: a modelled thread is the maximum-material design profile below.
|
||
|
||
| Form | `form` | Designation | Flanks | Depth | Crest flat | External minor | Internal minor, root |
|
||
|---|---|---|---|---|---|---|---|
|
||
| ISO metric | `metric` | `M10`, `M10x1`, `M16xPh3P1.5` | 30° / 30° | 5H/8, H = P √3/2 | P/8 at d, P/4 at D1 | d − 5H/4 | D1 = d − 5H/4, D = d |
|
||
| Trapezoidal | `trapezoidal` | `Tr20x4`, `Tr40x14(P7)` | 15° / 15° | H1 = P/2 | P/2 (1 − tan 15°) = 0.366 P | d3 = d − 2 (H1 + ac) | D1 = d − P, D4 = d + 2 ac |
|
||
| Acme (general purpose) | `acme` | `1/2-10 ACME` | 14.5° / 14.5° | h = P/2 | P/2 (1 − tan 14.5°) = 0.3707 P | d − P − 0.020″ (0.010″ finer than 10 tpi) | D − P, D + 0.020″ (0.010″) |
|
||
| Metric buttress | `buttress` | `S20x4`, `S40x14(P7)` | 3° (load) / 30° | H1 = 0.75 P | (P − 0.75 P (tan 3° + tan 30°))/2 = 0.26384 P | d3 = d − 2 × 0.86777 P | D1 = d − 1.5 P, D = d |
|
||
| Buttress inch | `buttress_asme` | `2.5-8 BUTT` | 7° (load) / 45° | h = 0.6 P | (P − 0.6 P (tan 7° + 1))/2 = 0.16316 P | d − 1.2 P (basic) | d − 1.2 P, d (basic) |
|
||
|
||
Trapezoidal clearance ac (ISO 2904): 0.15 mm for P = 1.5, 0.25 mm for P 2 to 5, 0.5 mm for P 6 to
|
||
12, 1 mm for P 14 to 44.
|
||
|
||
The square thread is refused: no current ISO, ASME or DIN standard defines one. Machinery's
|
||
Handbook gives only historical proportions (depth and width P/2; the "modified square" 10°); the
|
||
trapezoidal and Acme forms replaced it.
|
||
|
||
**Sizes.** Without a designation the thread takes the standard size that fits the face: a shaft
|
||
its major diameter, a hole its drill (metric: the tap drill d − P; the other forms: the internal
|
||
minor diameter). Metric uses the ISO 261/262 coarse pitches (M1.6 to M56); trapezoidal and metric
|
||
buttress the ISO 2902 middle pitch of each diameter (Tr8x1.5 to Tr130x14; buttress from S10x2),
|
||
the series DIN 513-2 shares; Acme ASME B1.5's preferred sizes (1/4-16 to 5-2). Buttress inch has
|
||
no size table here: its pitch is always given.
|
||
|
||
**Hand.** `hand: right | left | both`. A left-handed groove is the right-handed one's mirror image
|
||
(the screw motion about the reversed axis, rising along it); `both` cuts a right- and a
|
||
left-handed groove crossing on the face (a reversing screw).
|
||
|
||
**Buttress direction.** `steep_flank: end | start` says which way the steep (load) flank of the
|
||
screw's teeth faces along the thread's axis; a nut cut with the same setting mates with it (its
|
||
own steep flanks face the other way).
|
||
|
||
## Extent
|
||
|
||
`extent: full | length | up_to`, `length`, `up_to` (a point's place along the axis, or where a
|
||
plane crosses it), `from` (a point near the end the thread starts at).
|
||
|
||
A face end is **free** when no material lies past it in the groove's way: over the span from one
|
||
pitch to one and a half past the end, within the radii the groove cuts (the external minor
|
||
diameter to the major, a nut's minor diameter to its root, and the face itself). A cap, a chamfer
|
||
the groove runs out through, a counterbore wider than the thread are free; a shoulder, a head
|
||
whose corners reach past the root, a blind hole's bottom are not.
|
||
|
||
- At a free end the groove runs out a pitch past the end, into the air.
|
||
- At a closed end it stops with its section clear of the end: its centre as far inside as the
|
||
section reaches that way, so it never cuts into the shoulder.
|
||
- Inside the face it stops square. For a symmetric section a square stop inside material removes
|
||
exactly length / P turns (what the last section leaves uncut ahead of the stop, it cuts behind
|
||
it in mirror image).
|
||
|
||
A thread of some length starts at the end nearest `from`; without it, at the face's only free end;
|
||
without one, at the end the `face` point lies within a third of the face of. A pick in the middle
|
||
of a face whose ends are alike is refused, naming `from`. A length as long as the face runs the
|
||
whole face.
|
||
|
||
## Sources
|
||
|
||
- ISO 68-1 (basic profile), ISO 261/262 (sizes), ISO 965-1 (multi-start designation `Ph`).
|
||
- ISO 2901 to 2904 (trapezoidal: basic and design profiles, series, basic dimensions); the
|
||
design diameters checked against the Bornemann Gewindetechnik tables of DIN 103
|
||
(Tr10x2: d3 7.5, D4 10.5, D1 8; Tr40x7: 32, 41, 33; Tr100x20: 78, 102, 80):
|
||
<https://www.bornemann-gewindetechnik.de/de/produkte/trapezgewinde/daten/>.
|
||
- DIN 513-1/-2 (metric buttress): the formulas (ac = 0.11777 P, h3 = 0.86777 P, flat w =
|
||
0.26384 P, D1 = d − 2 H1) and the diameter-pitch table as IS 4696 (Part 3): 2004 publishes them
|
||
in line with DIN 513 (<https://law.resource.org/pub/in/bis/S01/is.4696.3.2004.pdf>), and the
|
||
Bornemann tables (S10x2: d3 6.529, D1 7; S40x7: 27.851, 29.5):
|
||
<https://www.bornemann-gewindetechnik.de/de/produkte/saegengewinde/daten/>.
|
||
- ASME B1.5 (Acme): flat 0.3707 P, h = P/2, the 0.020″/0.010″ minor and major allowances and the
|
||
preferred sizes, as reproduced at <https://torqbolt.com/unified-acme-threads-dimensions-specifications>.
|
||
- ASME B1.9 (buttress inch): 7°/45°, basic height of engagement 0.6 P; the flat follows from the
|
||
fundamental triangle H = P / (tan 7° + tan 45°) = 0.89064 P truncated equally at crest and root.
|
||
- ISO 3508 (thread runouts) and ISO 4753 (ends of parts with external threads) for the runout and
|
||
the chamfered tip.
|