jyvikoandClaude Opus 5.5
b1326e48d6
The edge mirror of a face's NURBS form: Edge::nurbs keeps the NURBS SMLib holds a conic as, and the edge's interval and its pcurves' parameter are its. Edge::parameters is the curve every evaluation at a parameter uses; curve says what the edge is. Nothing writes the form yet. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
147 lines
24 KiB
Markdown
147 lines
24 KiB
Markdown
# Kernel complexity ladder
|
||
|
||
Generated by `cargo xtask kernel-cases --ladder`. The ladder in [`tests/kernel-cases/ladder/`](../tests/kernel-cases/ladder/) orders kernel operations by complexity: each tier builds on the shapes of the tiers before it, so the last case carries everything. Every case is a test with its own right answer (analysis or invariants, as in the [regression rig](kernel-cases.md)); the golden (`tests/kernel-cases/ladder/golden.json`) records each case's time and what it made, orders each tier by time and flags slowdowns. The cases run on SMLib.
|
||
|
||
The **frontier** is the first case of a tier, in ladder order, that fails (fail, crash or hang).
|
||
|
||
## Tiers
|
||
|
||
| Tier | What | Cases | Results | Frontier |
|
||
|---|---|---|---|---|
|
||
| 01-primitives | primitives with closed-form volumes | 6 | 6 pass | – |
|
||
| 02-booleans | booleans in the degeneracy classes, and cuts that end in a single line | 20 | 1 fail, 19 pass | 018-hole-tangent-to-side-face |
|
||
| 03-analytic-profiles | extrudes and revolves of line-and-arc profiles | 9 | 9 pass | – |
|
||
| 04-spline-profiles | spline profiles, sweeps and lofts | 10 | 10 pass | – |
|
||
| 05-holes-and-taps | holes and tapped holes | 13 | 1 fail, 12 pass | 010-hole-tangent-to-end-face |
|
||
| 06-threads | modelled threads | 10 | 1 fail, 7 pass, 2 unsupported | 006-external-m10-into-chamfer |
|
||
| 07-fillets | constant, variable and corner fillets | 17 | 3 fail, 12 pass, 2 unsupported | 012-variable-into-rounded-corner |
|
||
| 08-chamfers | chamfers | 8 | 1 fail, 7 pass | 008-part-chamfers |
|
||
| 09-shells-and-offsets | shells and offsets | 11 | 2 fail, 9 pass | 010-shell-under-rounded-top |
|
||
| 10-patterns-and-mirrors | patterns and mirrors | 8 | 1 fail, 7 pass | 008-part-vents |
|
||
| 11-cumulative-parts | parts combining every tier | 4 | 3 fail, 1 pass | 002-flange |
|
||
|
||
Cases where SMLib's check gave no verdict on a body (SMLib can't take the record yet), so only the record's checks graded validity: 0.
|
||
|
||
## Cases, in ladder order
|
||
|
||
Times are the commands' own, in seconds, from the case's process; **golden** is the recorded time.
|
||
|
||
| Case | What | Answer | Result | s | golden s | changes |
|
||
|---|---|---|---|---|---|---|
|
||
| ladder/01-primitives/001-box | a 60x40x20 box: the stock every later tier starts from | analytic | pass | 0.003 | – | status was unsupported |
|
||
| ladder/01-primitives/002-cylinder | a cylinder r10 h30 | analytic | pass | 0.031 | – | status was unsupported |
|
||
| ladder/01-primitives/004-frustum | a cone frustum r10 -> r5, h20 (revolved trapezoid) | analytic | pass | 0.035 | – | status was unsupported |
|
||
| ladder/01-primitives/003-cone | a cone r10 h30 (no cone primitive: a revolved right triangle, its axis a sketch line) | analytic | pass | 0.028 | – | status was unsupported |
|
||
| ladder/01-primitives/005-sphere | a sphere r10 | analytic | pass | 0.009 | – | status was unsupported |
|
||
| ladder/01-primitives/006-torus | a torus R20 r5 | analytic | pass | 1.466 | – | status was unsupported |
|
||
| ladder/02-booleans/004-edge-on-edge-no-overlap | a cut tool that shares only the top front edge of the stock | analytic | pass | 0.010 | – | status was unsupported |
|
||
| ladder/02-booleans/003-pocket-flush-with-top | a 20x20x10 pocket whose tool's top is the stock's top face | analytic | pass | 0.011 | – | status was unsupported |
|
||
| ladder/02-booleans/015-knife-edge-wedge-cut | a triangular prism cut whose slope meets the bottom face along one line (a knife edge), its other faces on the stock's | analytic | pass | 0.007 | – | status was unsupported |
|
||
| ladder/02-booleans/002-coplanar-overlap-join | two 60x40x20 boxes overlapping 30x20 in plan, tops and bottoms coplanar | analytic | pass | 0.007 | – | status was unsupported |
|
||
| ladder/02-booleans/019-notch-flush-with-end-face | a notch 40x20 through the height, its end flush with the stock's end face: a U | analytic | pass | 0.007 | – | status was unsupported |
|
||
| ladder/02-booleans/016-v-groove-pinches-bottom-to-line | a V groove whose apex touches the bottom face along a line, cut through: two pieces | analytic | pass | 0.007 | – | status was unsupported |
|
||
| ladder/02-booleans/013-cut-across-cylinder-seam | a 10x4 notch through a cylinder r10 across its +X side (where the seam lies) | analytic | pass | 0.063 | – | status was unsupported |
|
||
| ladder/02-booleans/001-coincident-face-join | a 60x40x10 box joined exactly on the stock's top face: one 60x40x30 box | analytic | pass | 0.007 | – | status was unsupported |
|
||
| ladder/02-booleans/009-near-tangent-overlap-1e-3 | a cylinder r10 along X dipping 1e-3 mm into the top face, cut: a groove 1e-3 deep | analytic | pass | 0.032 | – | status was unsupported |
|
||
| ladder/02-booleans/020-part-back-wall | the running part: a 60x10x15 back wall joined on the stock's top, flush with its back and ends | analytic | pass | 0.009 | – | status was unsupported |
|
||
| ladder/02-booleans/005-vertex-on-face-no-overlap | an inverted cone whose apex touches the middle of the top face, cut | analytic | pass | 0.042 | – | status was unsupported |
|
||
| ladder/02-booleans/018-hole-tangent-to-side-face | a through hole r10 tangent to the front face: the front face pinched to a line | analytic | **FAIL**: measure Part: the operation failed: not supported yet: tessellation: face 4 (plane): boundary crosses itself (want measurable); body_count 0 (want 1); volume_mm3 0 (want 41716.814693) | 0.068 | – | status was unsupported |
|
||
| ladder/02-booleans/010-near-tangent-overlap-1e-6 | a cylinder r10 along X dipping 1e-6 mm into the top face, cut | invariants | pass | 0.034 | – | status was unsupported |
|
||
| ladder/02-booleans/006-tangent-along-line-no-overlap | a cylinder r10 along X lying on the top face (tangent along a line), cut | analytic | pass | 0.031 | – | status was unsupported |
|
||
| ladder/02-booleans/008-near-tangent-gap-1e-6 | a cylinder r10 along X 1e-6 mm above the top face, cut | analytic | pass | 0.032 | – | status was unsupported |
|
||
| ladder/02-booleans/007-near-tangent-gap-1e-3 | a cylinder r10 along X 1e-3 mm above the top face, cut | analytic | pass | 0.032 | – | status was unsupported |
|
||
| ladder/02-booleans/017-cylinder-tangent-top-and-bottom | a cylinder r10 along X tangent to both the top and bottom faces, cut: two pieces with zero-angle cusps | analytic | pass | 0.060 | – | status was unsupported |
|
||
| ladder/02-booleans/011-tangent-along-circle-through-hole | a sphere r10 sitting in a through hole r10 at the top edge (tangent along the hole's top circle), cut | analytic | pass | 0.094 | – | status was unsupported |
|
||
| ladder/02-booleans/014-cut-through-sphere-pole | a 4x4 square post cut off the top of a sphere r10 through its pole | analytic | pass | 0.024 | – | status was unsupported |
|
||
| ladder/02-booleans/012-tangent-along-circle-bowl | a blind hole r10 10 deep, then a sphere r10 centred on its floor: the floor disk vanishes exactly | analytic | pass | 0.103 | – | status was unsupported |
|
||
| ladder/03-analytic-profiles/001-extrude-rect-with-arc-end | a 60x40 profile with a semicircular end r20, extruded 20 | analytic | pass | 0.016 | – | status was unsupported |
|
||
| ladder/03-analytic-profiles/003-extrude-tapered-circle | a circle r10 extruded 20 with a -5 deg taper (inward): a cone frustum | analytic | pass | 0.043 | – | status was unsupported |
|
||
| ladder/03-analytic-profiles/007-revolve-180-touching-axis | a 15x20 rectangle on the axis revolved 180 deg: a half cylinder | analytic | pass | 0.017 | – | status was unsupported |
|
||
| ladder/03-analytic-profiles/008-extrude-slot | a slot (centres 40 apart, width 20) extruded 10 | analytic | pass | 0.020 | – | status was unsupported |
|
||
| ladder/03-analytic-profiles/002-extrude-annulus | an annulus r20/r10 extruded 15 | analytic | pass | 0.057 | – | status was unsupported |
|
||
| ladder/03-analytic-profiles/004-revolve-full-off-axis | a 10x30 rectangle 10 mm off the Z axis revolved 360 deg: a tube | analytic | pass | 0.055 | – | status was unsupported |
|
||
| ladder/03-analytic-profiles/006-revolve-partial-90 | a 10x10 rectangle 10 mm off the axis revolved 90 deg | analytic | pass | 0.013 | – | status was unsupported |
|
||
| ladder/03-analytic-profiles/005-revolve-touching-axis-hemisphere | a quarter disk r20 with an edge on the Z axis revolved 360 deg: a hemisphere | analytic | pass | 0.085 | – | status was unsupported |
|
||
| ladder/03-analytic-profiles/009-part-boss-and-slot | the running part: a revolved boss r8 h10 joined on the top, a slot 15x8 cut through the base | analytic | pass | 0.148 | – | status was unsupported |
|
||
| ladder/04-spline-profiles/001-extrude-bezier-arch | a profile closed by a cubic Bezier arch (control-point spline, 4 points), extruded 10 | analytic | pass | 0.010 | – | status was unsupported |
|
||
| ladder/04-spline-profiles/008-loft-square-to-circle | a loft from a 40 square at z=0 to a circle r10 at z=30 | invariants | pass | 0.018 | – | status was unsupported |
|
||
| ladder/04-spline-profiles/006-loft-circle-frustum | a loft between circles r20 at z=0 and r10 at z=30 | analytic | pass | 0.039 | – | status was unsupported |
|
||
| ladder/04-spline-profiles/007-loft-three-circles | a smooth loft through circles r20, r10, r20 at z = 0, 20, 40 | invariants | pass | 0.059 | – | status was unsupported |
|
||
| ladder/04-spline-profiles/005-loft-square-frustum | a loft between a 40 square at z=0 and a 20 square at z=30 | analytic | pass | 0.005 | – | status was unsupported |
|
||
| ladder/04-spline-profiles/009-extrude-periodic-fit-spline | a closed periodic fit-point spline through 6 points, extruded 10 | invariants | pass | 0.021 | – | status was unsupported |
|
||
| ladder/04-spline-profiles/004-sweep-square-along-bezier | a 4x4 square swept along the same Bezier path | analytic | pass | 0.034 | – | status was unsupported |
|
||
| ladder/04-spline-profiles/002-revolve-bezier-profile | a profile with a Bezier side (r from 20 to 15 over z 0..30) revolved 360 deg about Z | analytic | pass | 0.092 | – | status was unsupported |
|
||
| ladder/04-spline-profiles/003-pipe-along-bezier | a pipe d4 along a planar Bezier path | analytic | pass | 0.115 | – | status was unsupported |
|
||
| ladder/04-spline-profiles/010-part-bezier-window | the running part: a Bezier-arched window cut through the back wall | analytic | pass | 0.212 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/010-hole-tangent-to-end-face | a d10 through hole tangent to the end face x=0 | analytic | **FAIL**: measure Part: the operation failed: not supported yet: tessellation: face 4 (plane): triangulation does not (want measurable); body_count 0 (want 1); volume_mm3 0 (want 46429.203673) | 0.055 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/002-simple-blind-flat | a d10 blind hole 10 deep, flat bottom | analytic | pass | 0.062 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/009-hole-0.5-from-edge | a d10 through hole whose wall is 0.5 mm from the end face | analytic | pass | 0.045 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/001-simple-through | a d10 through hole in the stock's top | analytic | pass | 0.045 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/006-tapped-m6-through | an M6 tapped hole through: the tap drill d5 (major - pitch), cosmetic thread | analytic | pass | 0.038 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/004-counterbore | a counterbored hole: d6.6 through, d11 x 6.4 counterbore | analytic | pass | 0.121 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/007-tapped-m8-blind | an M8 tapped blind hole 12 deep with a 118 deg drill point | analytic | pass | 0.064 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/003-drilled-blind-118 | a d10 drilled hole 10 deep to the shoulder with a 118 deg point | analytic | pass | 0.073 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/005-countersink | a countersunk hole: d6.6 through, d12 x 90 deg countersink | analytic | pass | 0.140 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/008-tapped-m5-into-curved-face | an M5 tapped hole drilled radially through a cylinder r20 lying along X | analytic | pass | 0.134 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/011-crossing-holes-steinmetz | two d10 through holes whose axes cross: vertical and along Y at z=10 | analytic | pass | 0.244 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/012-crossing-tapped-holes-offset | two M6 tapped holes (d5) crossing with axes 2 mm apart | analytic | pass | 0.128 | – | status was unsupported |
|
||
| ladder/05-holes-and-taps/013-part-holes | the running part: an M6 tapped through hole, an M5 tapped blind hole in the boss, a d3.3 hole down through wall and base | analytic | pass | 0.604 | – | status was unsupported |
|
||
| ladder/06-threads/003-external-m10-partial-length | a modelled M10 thread over 15 of the 30 mm: it stops square in the middle of the face | invariants | pass | 1.146 | – | status was unsupported |
|
||
| ladder/06-threads/005-internal-m10-through | a modelled internal M10 thread in a d8.5 (tap drill) hole through a 30x30x20 block | analytic | pass | 1.392 | – | status was unsupported |
|
||
| ladder/06-threads/004-external-m10-to-shoulder | a modelled M10 thread on a d10 shaft running down to a d16 shoulder | invariants | pass | 2.444 | – | status was unsupported |
|
||
| ladder/06-threads/001-external-m10-full | a modelled M10 thread over the whole of a d10 x 30 cylinder | analytic | pass | 2.593 | – | status was unsupported |
|
||
| ladder/06-threads/006-external-m10-into-chamfer | a d10 x 30 cylinder with a 1 mm chamfer on top, then a modelled M10 thread over its cylinder face, running out through the chamfer | analytic | **FAIL**: record_valid geometry: portable B-rep: face 25 loop 0 use 1: pcurve middle lifts off its edge's curve by 0.000045 (want ok) | 2.764 | – | status was unsupported |
|
||
| ladder/06-threads/002-external-m10x1-fine | a modelled fine M10x1 thread over a d10 x 30 cylinder | analytic | pass | 4.590 | – | status was unsupported |
|
||
| ladder/06-threads/010-part-threaded-boss | the running part with a modelled M16 thread on its d16 boss | invariants | pass | 1.482 | – | status was unsupported |
|
||
| ladder/06-threads/007-external-m10-at-filleted-shoulder | a modelled M10 thread on a d10 shaft whose root at the d16 shoulder has an r1 fillet | invariants | pass | 2.568 | – | status was unsupported |
|
||
| ladder/06-threads/008-multi-start-thread | a two-start M10 thread (lead 3, pitch 1.5) | invariants | not supported yet: solid.thread has no start count: multi-start threads | – | – | |
|
||
| ladder/06-threads/009-thread-runout-length | an M10 thread that vanishes over a 2-pitch runout before a shoulder | invariants | not supported yet: solid.thread has no runout (vanishing thread) length | – | – | |
|
||
| ladder/07-fillets/006-variable-r5-to-zero | a variable round on the top front edge, r5 at x=0 down to 0 at the x=60 vertex | analytic | pass | 0.018 | – | status was unsupported |
|
||
| ladder/07-fillets/005-variable-r5-to-r1 | a variable round on the top front edge, r5 at x=0 to r1 at x=60 | analytic | pass | 0.018 | – | status was unsupported |
|
||
| ladder/07-fillets/007-variable-r5-to-1e-3 | a variable round on the top front edge, r5 down to 1e-3 mm | analytic | pass | 0.018 | – | status was unsupported |
|
||
| ladder/07-fillets/015-corner-g2-patch | three r5 rounds at a corner with the g2 corner patch | invariants | not supported yet: step 2 (solid.fillet): invalid input: not supported yet: a fillet with G2 corner patches with the SMLib kernel | 0.005 | – | |
|
||
| ladder/07-fillets/008-constant-r1e-3 | a constant 1e-3 mm round on the top front edge | analytic | pass | 0.012 | – | status was unsupported |
|
||
| ladder/07-fillets/004-convex-and-concave-r5 | an L block: r5 on its inner (concave) vertical edge and on an outer (convex) one | analytic | pass | 0.025 | – | status was unsupported |
|
||
| ladder/07-fillets/001-single-edge-r5 | an r5 round on the stock's top front edge | analytic | pass | 0.012 | – | status was unsupported |
|
||
| ladder/07-fillets/012-variable-into-rounded-corner | a vertical r5 round, then a variable round r1 -> r5 along the top back edge into it | invariants | **FAIL**: step 3 (solid.fillet): SMLib variable fillet: operation: SMLib failed (status 1001) | 0.020 | – | status was unsupported |
|
||
| ladder/07-fillets/014-curved-edge-r2 | an r2 round on the top edge of a cylinder r10 h20 | analytic | pass | 0.113 | – | status was unsupported |
|
||
| ladder/07-fillets/011-chain-ending-at-corner | r5 rounds on two top edges meeting at a corner whose vertical edge stays sharp | invariants | pass | 0.017 | – | status was unsupported |
|
||
| ladder/07-fillets/002-four-vertical-edges-r5 | r5 rounds on the four vertical edges | analytic | pass | 0.028 | – | status was unsupported |
|
||
| ladder/07-fillets/009-corner-three-equal-r5 | r5 rounds on the three edges meeting at the corner (60,40,20): a sphere corner | analytic | pass | 0.025 | – | status was unsupported |
|
||
| ladder/07-fillets/010-corner-unequal-r7-r3 | an r7 vertical round at a corner, then r3 along a top edge, which runs on round the r7 arc to the other top edge | invariants | pass | 0.042 | – | status was unsupported |
|
||
| ladder/07-fillets/003-tangent-chain-r3 | an r3 round all round the top of the box with r5 vertical rounds: a tangent chain of lines and arcs | analytic | pass | 0.090 | – | status was unsupported |
|
||
| ladder/07-fillets/016-corner-three-sequential-r5-r3-r7 | rounds r5 and r3 on the two top edges at a corner, then r7 on the vertical edge under them | invariants | **FAIL**: step 4 (solid.fillet): SMLib fillet: operation: SMLib rejected the input (SM_ERR_INVALID_INPUT) | 0.051 | – | status was unsupported |
|
||
| ladder/07-fillets/017-part-rounds | the running part: r5 on the front vertical edges, r3 on the back wall's top front edge, r1 where the boss meets the top | analytic | **FAIL**: step 21 (solid.fillet): SMLib fillet: operation: SMLib rejected the input (SM_ERR_INVALID_INPUT) | 0.986 | – | status was unsupported |
|
||
| ladder/07-fillets/013-corner-setback | three r5 rounds at a corner with setbacks of 8 mm along each edge | invariants | not supported yet: solid.fillet has no corner setback distances | – | – | |
|
||
| ladder/08-chamfers/002-two-distances-5-3 | a 5 x 3 chamfer on the top front edge | analytic | pass | 0.009 | – | status was unsupported |
|
||
| ladder/08-chamfers/001-equal-5 | a 5 mm chamfer on the top front edge | analytic | pass | 0.010 | – | status was unsupported |
|
||
| ladder/08-chamfers/003-distance-angle-5-30 | a chamfer 5 mm at 30 deg on the top front edge | analytic | pass | 0.010 | – | status was unsupported |
|
||
| ladder/08-chamfers/005-corner-two-mitred-3 | 3 mm chamfers on two top edges meeting at a corner (mitred) | analytic | pass | 0.014 | – | status was unsupported |
|
||
| ladder/08-chamfers/004-corner-three-equal-3 | 3 mm chamfers on the three edges meeting at a corner | analytic | pass | 0.015 | – | status was unsupported |
|
||
| ladder/08-chamfers/007-chamfer-then-fillets | a 3 mm chamfer on the top front edge, then r2 rounds on the front vertical edges that meet it | invariants | pass | 0.029 | – | status was unsupported |
|
||
| ladder/08-chamfers/006-curved-edge-2 | a 2 mm chamfer on the top edge of a cylinder r10 h20 | analytic | pass | 0.117 | – | status was unsupported |
|
||
| ladder/08-chamfers/008-part-chamfers | the running part: 1 mm on the boss top edge, 2 mm on the back wall's top back edge | analytic | **FAIL**: step 21 (solid.fillet): SMLib fillet: operation: SMLib rejected the input (SM_ERR_INVALID_INPUT) | 0.999 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/007-offset-top-face-5 | the stock's top face offset 5 mm | analytic | pass | 0.016 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/003-tube-two-open-faces | the stock shelled 2 mm, open top and bottom | analytic | pass | 0.017 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/001-box-open-top-t2 | the stock shelled 2 mm, open at the top | analytic | pass | 0.021 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/004-thin-wall-0.2 | the stock shelled 0.2 mm, open at the top | analytic | pass | 0.015 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/009-shell-outside-t2 | the stock shelled 2 mm outward, open at the top | analytic | pass | 0.044 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/008-offset-cylinder-wall-2 | a cylinder r10 h20 with its side face offset 2 mm | analytic | pass | 0.155 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/002-cylinder-open-top-t1 | a cylinder r10 h30 shelled 1 mm, open at the top | analytic | pass | 0.160 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/006-shell-rounds-r1-thinner-than-t2 | the box with r1 vertical rounds shelled 2 mm: the inner corners close sharp | analytic | pass | 0.063 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/005-shell-rounds-r5-t2 | the box with r5 vertical rounds shelled 2 mm open at the top: the inner corners r3 | analytic | pass | 0.164 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/010-shell-under-rounded-top | the stock with r3 rounds on its four top edges, shelled 2 mm open at the bottom | invariants | **FAIL**: step 3 (solid.shell): SMLib shell: SMLib's check refuses the result: 1 failed tests: SmBSplineCurve::Test #13 Bad CurveCusp: 2D BSplineCurve Warning: Extremely | 0.179 | – | status was unsupported |
|
||
| ladder/09-shells-and-offsets/011-part-shell | the running part shelled 1.5 mm open at the bottom | invariants | **FAIL**: step 21 (solid.fillet): SMLib fillet: operation: SMLib rejected the input (SM_ERR_INVALID_INPUT) | 0.998 | – | status was unsupported |
|
||
| ladder/10-patterns-and-mirrors/007-pattern-bodies | a pin r3 h10 patterned 4 times at 10 mm as bodies | analytic | pass | 0.037 | – | status was unsupported |
|
||
| ladder/10-patterns-and-mirrors/005-mirror-feature | a d10 hole in the stock mirrored about x=30 as a feature | analytic | pass | 0.126 | – | status was unsupported |
|
||
| ladder/10-patterns-and-mirrors/004-mirror-body-joined | a 30x40x20 half with a d10 hole mirrored about x=30 and joined: the faces at x=30 coincide | analytic | pass | 0.138 | – | status was unsupported |
|
||
| ladder/10-patterns-and-mirrors/001-rect-pattern-holes | a d5 hole patterned 3 x 2 at 20 mm in a 60x40x10 plate | analytic | pass | 0.572 | – | status was unsupported |
|
||
| ladder/10-patterns-and-mirrors/003-overlapping-pattern-leaves-core | six r5 cuts patterned round a circle r6 in a disk r20: they overlap and cut a core free | analytic | pass | 0.836 | – | status was unsupported |
|
||
| ladder/10-patterns-and-mirrors/002-circular-pattern-holes | a d6 hole patterned 8 times round a disk r30 h10 | analytic | pass | 1.322 | – | status was unsupported |
|
||
| ladder/10-patterns-and-mirrors/006-circular-pattern-counterbores | a counterbored hole (d5, d9 x 3) patterned 6 times round a disk r30 h10 | analytic | pass | 2.310 | – | status was unsupported |
|
||
| ladder/10-patterns-and-mirrors/008-part-vents | the running part with a d3 vent hole in its top patterned 4 times at 5 mm | invariants | **FAIL**: step 21 (solid.fillet): SMLib fillet: operation: SMLib rejected the input (SM_ERR_INVALID_INPUT) | 0.978 | – | status was unsupported |
|
||
| ladder/11-cumulative-parts/002-flange | a revolved flange and hub with a bore, six bolt holes, a hub chamfer and a hub-root round | analytic | **FAIL**: step 7 (solid.chamfer): SMLib chamfer: operation: SMLib rejected the input (SM_ERR_INVALID_INPUT) | 1.244 | – | status was unsupported |
|
||
| ladder/11-cumulative-parts/001-bracket | an L bracket: concave r5 round, 5 mm outer chamfer, a hole in each leg | analytic | pass | 0.153 | – | status was unsupported |
|
||
| ladder/11-cumulative-parts/003-threaded-flange | the flange with a modelled M30 thread on its hub, between the round and the chamfer, and M8 tapped holes in the disk | invariants | **FAIL**: step 7 (solid.chamfer): SMLib chamfer: operation: SMLib rejected the input (SM_ERR_INVALID_INPUT) | 1.171 | – | status was unsupported |
|
||
| ladder/11-cumulative-parts/004-housing | the running part with every tier: back wall, boss, slot, spline window, tapped holes, rounds, chamfers, shell, vents, and a modelled M16 thread on the boss | invariants | **FAIL**: step 21 (solid.fillet): SMLib fillet: operation: SMLib rejected the input (SM_ERR_INVALID_INPUT) | 0.913 | – | status was unsupported |
|