Three forms: `bspp` (G, ISO 228-1, 55° parallel), `bspt` (R external, Rc internal, ISO 7-1, 55° taper 1 in 16) and `npt` (ASME B1.20.1, 60° taper 1 in 16). Their sizes are tabulated from the public sources: ISO 7-1:1978 Table 1 (its gauge-plane diameters are the G sizes) and NBS Handbook H28 (1957) Table VII.2; tests check every row against the standards' own relations. A taper thread starts at its free end with its standard diameter there (external: the gauge diameter its gauge length in, internal: at the face). Its groove is the screw sweep with the section moved 1/32 of the axial travel off the axis (the radial law the runouts use, added to it), its section reaching just past the crest, and the material beyond the major cone (or inside the minor cone) is cut with it, as a die or tap cuts the crests. An external one runs its standard length by default. The volumes are checked against the profile's material fraction integrated over the tapered radii: G 1/2 to 2e-6, R 1/2, Rc 1/2 and 1/2-14 NPT within 0.2 % of the cut. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
152 lines
11 KiB
Markdown
152 lines
11 KiB
Markdown
# Threads
|
||
|
||
`solid.thread` puts a thread on a cylindrical face: cosmetic (an annotation, `model.threads`
|
||
lists it) or modelled (the groove between the teeth cut into the body along a helix, SMLib's exact
|
||
screw sweep). This page gives the forms, the values each uses and where they come from, and how a
|
||
thread's extent is decided. The code is `crates/doc/src/thread_forms.rs` (forms, sizes,
|
||
designations) and `crates/doc/src/eval_thread.rs` (the thread on its face, the cut).
|
||
|
||
## Forms
|
||
|
||
Every groove is a polygon in an axial half-plane: straight flanks, flat crest and root. Crest and
|
||
root radii (the ISO metric root radius, the buttress root radius R, DIN 405 knuckle and Whitworth
|
||
rounds) are not modelled. External threads are cut from the shaft's surface (a little past it, so
|
||
no skin is left) down to the external thread's minor diameter; internal threads from the hole
|
||
wall out to the internal thread's root. Pitch-diameter allowances and tolerance classes are not
|
||
modelled: a modelled thread is the maximum-material design profile below.
|
||
|
||
| Form | `form` | Designation | Flanks | Depth | Crest flat | External minor | Internal minor, root |
|
||
|---|---|---|---|---|---|---|---|
|
||
| ISO metric | `metric` | `M10`, `M10x1`, `M16xPh3P1.5` | 30° / 30° | 5H/8, H = P √3/2 | P/8 at d, P/4 at D1 | d − 5H/4 | D1 = d − 5H/4, D = d |
|
||
| Trapezoidal | `trapezoidal` | `Tr20x4`, `Tr40x14(P7)` | 15° / 15° | H1 = P/2 | P/2 (1 − tan 15°) = 0.366 P | d3 = d − 2 (H1 + ac) | D1 = d − P, D4 = d + 2 ac |
|
||
| Acme (general purpose) | `acme` | `1/2-10 ACME` | 14.5° / 14.5° | h = P/2 | P/2 (1 − tan 14.5°) = 0.3707 P | d − P − 0.020″ (0.010″ finer than 10 tpi) | D − P, D + 0.020″ (0.010″) |
|
||
| Metric buttress | `buttress` | `S20x4`, `S40x14(P7)` | 3° (load) / 30° | H1 = 0.75 P | (P − 0.75 P (tan 3° + tan 30°))/2 = 0.26384 P | d3 = d − 2 × 0.86777 P | D1 = d − 1.5 P, D = d |
|
||
| Buttress inch | `buttress_asme` | `2.5-8 BUTT` | 7° (load) / 45° | h = 0.6 P | (P − 0.6 P (tan 7° + 1))/2 = 0.16316 P | d − 1.2 P (basic) | d − 1.2 P, d (basic) |
|
||
|
||
| Parallel pipe | `bspp` | `G 1/2` | 27.5° / 27.5° | h = 0.640327 P of H = 0.960491 P | (H − h) tan 27.5° = 0.1667 P, both | d − 2h | d − 2h, d |
|
||
| Taper pipe (ISO 7-1) | `bspt` | `R 1/2`, `Rc 1/2` | 27.5° / 27.5° | h = 0.640327 P of H = 0.960237 P | (H − h) tan 27.5°, both | d − 2h at the gauge plane | d − 2h, d at the gauge plane |
|
||
| NPT | `npt` | `1/2-14 NPT` | 30° / 30° | h = 0.8 P of H = 0.866025 P | (H − h) tan 30° = 0.038 P, both | E − h at the plane of E | E − h, E + h |
|
||
|
||
The pipe threads' crest and root rounds (ISO 228-1/7-1 r = 0.137329 P, 0.137278 P taper) are
|
||
modelled as flats at the basic height, as the other forms' radii; NPT takes the minimum truncation
|
||
0.033 P at both. The flanks' bisector is square to the axis in all three.
|
||
|
||
**Taper pipe threads** (`bspt`, `npt`): the diameters change 1 in 16 along the axis. The thread
|
||
starts at a free end, the pipe's end or the hole's mouth (`from`), with the diameter its standard
|
||
puts there: an external thread its major diameter at the gauge (reference) plane its gauge length
|
||
in from the small end (ISO 7-1: the basic gauge length, R 1/2 20.955 mm at 8.2 mm; NPT: E1 + h at
|
||
the hand-tight length L1, E1 = E0 + L1/16), an internal one the reference diameter at its face
|
||
(ISO 7-1's gauge plane; NPT's E1 at the large end). The groove is SMLib's screw sweep with its
|
||
section moved 1/32 of the axial travel off the axis per unit length (the radial law that also
|
||
makes runouts), its walls within the sweep's tolerance of the true surfaces; its section reaches
|
||
just past the crest, and the material beyond the major cone (external) or inside the minor cone
|
||
(internal) is cut with it, as the die or tap cuts the crests. Past the major cone the crests
|
||
vanish into the pipe's surface (ISO 7-1's incomplete thread). An external taper thread runs its
|
||
standard length unless `length` or `up_to` says otherwise (ISO 7-1's useful thread for the basic
|
||
gauge length, NPT's effective thread L2); an internal one the face. A pipe thread has one start and
|
||
turns one way; a chamfered tip is not cut on a taper thread yet. ISO 228-1's G sizes are ISO 7-1's
|
||
gauge-plane diameters (1/16 to 6); ISO 228-1's extra sizes (5/8, 7/8, …) are not tabulated yet, nor
|
||
is ISO 7-1's parallel internal Rp.
|
||
|
||
Trapezoidal clearance ac (ISO 2904): 0.15 mm for P = 1.5, 0.25 mm for P 2 to 5, 0.5 mm for P 6 to
|
||
12, 1 mm for P 14 to 44.
|
||
|
||
The square thread is refused: no current ISO, ASME or DIN standard defines one. Machinery's
|
||
Handbook gives only historical proportions (depth and width P/2; the "modified square" 10°); the
|
||
trapezoidal and Acme forms replaced it.
|
||
|
||
**Sizes.** Without a designation the thread takes the standard size that fits the face: a shaft
|
||
its major diameter, a hole its drill (metric: the tap drill d − P; the other forms: the internal
|
||
minor diameter). Metric uses the ISO 261/262 coarse pitches (M1.6 to M56); trapezoidal and metric
|
||
buttress the ISO 2902 middle pitch of each diameter (Tr8x1.5 to Tr130x14; buttress from S10x2),
|
||
the series DIN 513-2 shares; Acme ASME B1.5's preferred sizes (1/4-16 to 5-2). Buttress inch has
|
||
no size table here: its pitch is always given.
|
||
|
||
**Hand.** `hand: right | left | both`. A left-handed groove is the right-handed one's mirror image
|
||
(the screw motion about the reversed axis, rising along it); `both` cuts a right- and a
|
||
left-handed groove crossing on the face (a reversing screw).
|
||
|
||
**Buttress direction.** `steep_flank: end | start` says which way the steep (load) flank of the
|
||
screw's teeth faces along the thread's axis; a nut cut with the same setting mates with it (its
|
||
own steep flanks face the other way).
|
||
|
||
## Extent
|
||
|
||
`extent: full | length | up_to`, `length`, `up_to` (a point's place along the axis, or where a
|
||
plane crosses it), `from` (a point near the end the thread starts at).
|
||
|
||
A face end is **free** when no material lies past it in the groove's way: over the span from one
|
||
pitch to one and a half past the end, within the radii the groove cuts (the external minor
|
||
diameter to the major, a nut's minor diameter to its root, and the face itself). A cap, a chamfer
|
||
the groove runs out through, a counterbore wider than the thread are free; a shoulder, a head
|
||
whose corners reach past the root, a blind hole's bottom are not.
|
||
|
||
- At a free end the groove runs out a pitch past the end, into the air.
|
||
- At a closed end it stops with its section clear of the end: its centre as far inside as the
|
||
section reaches that way, so it never cuts into the shoulder.
|
||
- Inside the face it stops square. For a symmetric section a square stop inside material removes
|
||
exactly length / P turns (what the last section leaves uncut ahead of the stop, it cuts behind
|
||
it in mirror image).
|
||
|
||
A thread of some length starts at the end nearest `from`; without it, at the face's only free end;
|
||
without one, at the end the `face` point lies within a third of the face of. A pick in the middle
|
||
of a face whose ends are alike is refused, naming `from`. A length as long as the face runs the
|
||
whole face.
|
||
|
||
## Runout and tip
|
||
|
||
**Runout** (`ease_in`, `ease_out`: a length, `standard` = 2.5 P or `short` = 1.25 P, ISO 3508's
|
||
normal and short thread runouts x): the groove fades out over that length, its section moving
|
||
out of the material as it turns (an external thread's away from the axis, past the surface; a
|
||
nut's towards it, into the hole), linearly, by SMLib's radial screw sweep. `ease_in` is at the end
|
||
the thread starts from (`from`, or the start of its extent), `ease_out` at the other. The runout
|
||
lies past the full-form length: beyond a square stop, and before a shoulder up to its clearance
|
||
(the full form then ends a runout short of it); at a free end it lies inside the face, the groove
|
||
reaching nothing at the end. No end gets a runout unless asked. Where the section moves, the
|
||
sweep's walls are within its tolerance (1e-4 P) of the true surfaces; full-depth turns are exact
|
||
radially.
|
||
|
||
**Tip** (ISO 4753's chamfered end; `tip: start` the end the thread starts from, which must be
|
||
free, `tip: both` each free end it reaches): at those ends of a modelled external thread, after the groove, the material outside a cone `chamfer_angle` to the axis (45°) reaching
|
||
d_f = d − 2 `chamfer_depth` at the end is cut, the last teeth tapering into it. ISO 4753 bounds
|
||
d_f by the minor diameter; the default is that bound, the external minor diameter d3 = d −
|
||
1.226869 P of ISO 724 (8.160 for M10), which lies below the modelled basic root d1. The cone
|
||
therefore crosses the root and leaves the end a whole disk of d3 inside a whole conical ring; a
|
||
cone ending on the root itself would pinch to nothing wherever the groove reaches the end. ISO
|
||
4753 is for ISO metric threads, so the other forms give `chamfer_depth`. An internal thread takes
|
||
the hole's countersink instead.
|
||
|
||
## Sources
|
||
|
||
- ISO 68-1 (basic profile), ISO 261/262 (sizes), ISO 965-1 (multi-start designation `Ph`).
|
||
- ISO 2901 to 2904 (trapezoidal: basic and design profiles, series, basic dimensions); the
|
||
design diameters checked against the Bornemann Gewindetechnik tables of DIN 103
|
||
(Tr10x2: d3 7.5, D4 10.5, D1 8; Tr40x7: 32, 41, 33; Tr100x20: 78, 102, 80):
|
||
<https://www.bornemann-gewindetechnik.de/de/produkte/trapezgewinde/daten/>.
|
||
- DIN 513-1/-2 (metric buttress): the formulas (ac = 0.11777 P, h3 = 0.86777 P, flat w =
|
||
0.26384 P, D1 = d − 2 H1) and the diameter-pitch table as IS 4696 (Part 3): 2004 publishes them
|
||
in line with DIN 513 (<https://law.resource.org/pub/in/bis/S01/is.4696.3.2004.pdf>), and the
|
||
Bornemann tables (S10x2: d3 6.529, D1 7; S40x7: 27.851, 29.5):
|
||
<https://www.bornemann-gewindetechnik.de/de/produkte/saegengewinde/daten/>.
|
||
- ASME B1.5 (Acme): flat 0.3707 P, h = P/2, the 0.020″/0.010″ minor and major allowances and the
|
||
preferred sizes, as reproduced at <https://torqbolt.com/unified-acme-threads-dimensions-specifications>.
|
||
- ASME B1.9 (buttress inch): 7°/45°, basic height of engagement 0.6 P; the flat follows from the
|
||
fundamental triangle H = P / (tan 7° + tan 45°) = 0.89064 P truncated equally at crest and root.
|
||
- ISO 3508 (thread runouts) and ISO 4753 (ends of parts with external threads) for the runout and
|
||
the chamfered tip. ISO 4753:2011, figure 1 b) (chamfered end CH; the public preview at
|
||
<https://cdn.standards.iteh.ai/samples/55928/38ddde12863b4c2db35dc929fd502a4d/ISO-4753-2011.pdf>):
|
||
the end's diameter "Maximum diameter at the minor thread diameter", the angle ≤ 50°, the
|
||
incomplete thread u ≤ 2 P.
|
||
- ISO 7-1:1978 (taper and parallel 55° profiles: H = 0.960237 P / 0.960491 P, h = 0.640327 P,
|
||
r = 0.137278 P / 0.137329 P, figures 1 and 2; Table 1, columns 1 to 8 and 15: threads per 25.4
|
||
mm, major diameter at the gauge plane, basic gauge length, useful thread), from the public
|
||
preview <https://cdn.standards.iteh.ai/samples/2856/96e1948d3d734f28b2563bcab2920245/ISO-7-1-1978.pdf>;
|
||
the same diameters as G sizes in <https://en.wikipedia.org/wiki/British_Standard_Pipe> and the
|
||
Yamawa YEU23 tables `pipe_thread_catalog.rs` cites.
|
||
- ASME B1.20.1 (NPT) as NBS Handbook H28 (1957) Part II, section VII publishes it: 60°, H =
|
||
0.866025 p, h = 0.800 p, truncation at least 0.033 p, taper 1 in 16, E0 = D − (0.05 D + 1.1) p,
|
||
E1 = E0 + 0.0625 L1, L2 = (0.80 D + 6.8) p, and Table VII.2 (D, n, E0, L1, L2 for 1/16 to 12):
|
||
<https://nvlpubs.nist.gov/nistpubs/Legacy/hb/nbshandbook28supp1957pt2.pdf>.
|
||
- ISO 724 (external minor diameter d3 = d1 − H/6 = d − 1.226869 P, M10x1.5: 8.16), as given at
|
||
<https://www.valvias.com/miscellanea-metric-thread-din-13.php>.
|