Two expectations encoded truck-era output:
- a_flange_bent_inside_keeps_the_base_sketchs_arcs_in_the_flat_pattern_and_the_dxf: the
DXF has 7 LINEs, 4 ARCs, 11 shapes (was 9, 4, 13). The flat outline is SMLib's exact 2D
union of the plate, the bend zone and the flange panel; a zone's side and its panel's side
meet in line, and a region's boundary has no vertex in the middle of a straight run, so
each flange side is one line: 6 outline lines (plate top, left, right; flange sides and
end) and the bend's centre line. The same reason as 5d25684a1 gave for
a_base_trimmed_for_a_flange_keeps_its_arcs (12 to 10 edges). Areas, the bend length and
the volumes are checked as before and hold.
- hole_beside_two_adjacent_edge_flanges_cuts_and_bends_stay_guarded: the folded volume was
14057.2 +- 0.1, a faceted measure; since 32ae0cd9c the measure is SMLib's exact integral,
14057.3837123. Exactly, a folded sheet holds its flat area A times t, less each bend's flat
strip L·t·(R + K·t)·π/2, plus its sector L·t·(R + t/2)·π/2: t·A + t²·(½ − K)·(π/2)·L. With
t = R = 2.5, K = 0.44, A = 5597.0353454 (the flat pattern) and L = 75 + 35, that is
13992.5883635 + 64.7953485 = 14057.3837120, within 2e-11 relative of the measure. The
test now checks that identity to 1e-9.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A face's sheet name is the name 80% of its mesh triangles' centres agree on. SMLib's
mesher fans a 1 mm rim (30 mm tall) into four triangles about its middle; two of their
centres lie 1/6 mm from the panel's top or bottom face, inside the 0.2·t tolerance, and
took that face's name, so the rim got no name (rim.side0/side1/ext0/ext1 of the tray's
flanges: 6 faces unnamed). A flat face's name now needs its plane to face along the
triangle's normal (within 1e-3); otherwise the point is a rim's, a bend's or an ext rim's.
No face changes name: these faces had none.
sheet::face_names_tests::a_trays_faces_have_readable_sheet_names_that_follow_its_size now
passes its naming checks and fails later, on the point named_face_point gives for a rim
(the roomiest triangle's incentre, 0.497 mm from the rim's edge, not 0.5).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A hole drawn on a flange's face and cut through ("direction": "negative") was refused as
"below the supported 0.000001 mm extrusion resolution": the flange panel's frame, turned
up by the cosine and sine of 90 degrees, puts the panel's origin at -1.9999999999999998
along the sketch normal, so the cut ends 2.2e-16 mm short of the sheet's far face and
reads as a layer 2.2e-16 thick. A depth within four units in the last place of the
numbers it is worked out from (the frame origins, the tool's span and the thickness) now
lands on the face. A real thin layer stays: a 1e-8 mm layer of a sheet 1e5 mm from the
origin (bound 9e-11 there) is still refused
(partial_depth_intersect_sub_extrusion_resolution_layers_refuse_atomically passes).
Fixes sheet::tests::a_sketch_on_a_sheet_face_follows_the_sheet_when_its_thickness_changes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since 09c979a4b a circle in a profile is one closed arc (Loop2::circle). The sheet's
faces passed it to the sew as one arc edge from a point back to itself, which the sew
refuses ("sew: a degenerate edge"): a sewn edge runs between two vertices, and an arc
edge is the circle through its ends and middle. A disc's flange failed (first with the
4-face minimum, then with the degenerate edge). Each closed curve of a cell is now split
into its two exact halves (Seg2::split_half) where the cell's edges are prepared, as a
hole's wall already came out: a disc is two caps and two half walls.
sheet::tests::tiny_cut_inside_exact_circle_survives_unfold_refold_and_dxf now builds the
disc flange and fails later, on SMLib's extrude of the 50 nm tool (an SMLib tolerance
defect, reported separately).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The case expected "drill 6.75 mm for M8", the major diameter less the pitch.
Since 05f1c6b9a (Tapped holes: the tap maker's drill for every form) a tabulated
size names the tap maker's drill, 6.8 mm for M8 x 1.25 (Yamawa YEU23 p.704), as
case 2115 already grades and engine thread_tests.rs asserts; major less pitch
is for a size no table lists. The refusal itself and its reason are unchanged.
The case passes and leaves threads/KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The zero-area triangle is dropped (previous commit): the box converts with six
faces and V = 1000 mm^3, as the case expects.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A triangle whose corners lie on one line (or weld into one another) adds no
surface, so welding now drops it, with any corner only it used, instead of
refusing the whole mesh as having a degenerate triangle. The closed and
consistently oriented check that follows still refuses a mesh that needed it to
close, and a mesh of nothing but such triangles is refused by name. Dropping its
unused corners keeps a dropped triangle from widening the part's extent, which
the prism search reads from every position.
Regression test a_zero_area_triangle_is_dropped: the 20 x 10 x 5 box with the
case's extra triangle (0,0,0) (10,0,0) (20,0,0) converts to six faces and
V = 1000 mm^3.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fixed_seeds_run_clean expected the join of a box touching the first only along
an edge to be refused with "zero-thickness edge contact". Since 94ee28d5c (doc:
a join keeps solids that only touch as separate bodies) such a join succeeds and
keeps the new box a body of its own with an along_edge notice, which
join_touching_along_an_edge_keeps_a_separate_body asserts in engine tests.rs.
The seed now expects that: the notice, two bodies, each valid, and the volumes
unmoved, 25 x 15 x 10 + 17.5 x 17.5 x 20 = 3750 + 6125 mm^3.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's thickening of the test sheet makes a top face of 72 x 78 control points,
which the 4096-point cap refused (TooLarge) before the solver saw it. The band
cap (2^21 entries, 16 MB) is what bounds the system's memory and its
factorisation (at most n min(n, bw)^2 work); the 72 x 78 bicubic net needs
5320 unknowns 213 apart, 1.14 M entries, well within it. The point cap now
bounds only the per-step energy sweep and the net's copies: 2^14 points, above
the band's own limit for square bicubic nets (about 90 x 90), so a face is
refused for the system it needs rather than its size. The hostile-input test
asks for 129 x 129 and checks the refusal is TooLarge.
a_body_face_is_faired_with_its_edges_untouched_and_its_history_kept passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The README demo's Raspberry Pi case stands four standoffs on its floor: Extrude2's ring of
radius 3 round a 1.25 hole, patterned by RectangularPattern1. Each is its outer wall, its inner
wall, its top and the floor inside it: four faces. The recorded counts were truck's, which made
each cylindrical wall two halves (six faces a standoff): 25 after feature 6, 43 after the
pattern, and 8 more than now at every step after it. On SMLib each wall is one face closed on
its seam, and the counts are 23, 35, 35, 47, 47, 51, 51, 55, 71 from feature 6 on (the feature
names show it: F6:side:c1, F6:side:c2, F6:top and the floor piece bounded by F6:side:c2 per
standoff). The outer sides stay one face each, and (b) and (c) still agree step by step.
Fixes cli rebuild_topology::pi_case_faces_per_step_at_both_heights.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- A modelled thread reopened with the designation 1/4-20 UNC on the M8 it was made as: the
thread is metric, and since b4549d270 (threads in the standard forms) an unknown designation
is named with its form: "unknown metric thread `1/4-20 UNC` (like M8 or M8x1)". The test looked
for the old wording, "ISO metric".
- Press Pull on a hole's wall opens Offset Faces with the whole wall: one face, closed on its
seam, on SMLib (a cylinder wall was two halves on truck).
Fixes ui-egui dialogs_thread::contribution_tests::expanded_catalogue_rejects_external_taper_holes_and_nonmetric_thread_features
and preselect_tests::press_pull_then_curved_face_offsets_it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A face on a B-spline surface closed around u (first and last control columns the same) may lie
across the surface's start without winding round it: the strip on a radius-3000 rational
cylinder whose seam is 0.001 rad into the strip. A kernel's trims run inside the surface's
knots, so its pcurve came back clamped at the start, 2.28 mm off its edge, and the strip was not
imported.
Before seams are added, such a surface is started anew in the middle of the stretch of u the
face leaves free (each loop followed round, unwrapped across the start; a face winding round is
the seams' to handle): the new start inserted to full multiplicity and the piece after it put
before the piece before it, a period on. The same points, a period apart in parameter before
the new start: exact. The face then lies inside the knots.
Fixes kernel step_in::tests::explicit_outer_bound_crossing_a_closed_nurbs_seam_stays_trimmed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Two tests counted the old 2D boolean's edges, which kept a vertex wherever an operand's corner
or edge end lay on another's edge. SMLib's planar boolean leaves no vertex that is no corner:
edges on one line within the tolerance are one edge. The results are the same regions with
fewer, whole edges, and each test's point stands (no edge shorter than the tolerance, no sliver):
- a quadrilateral cut away from below a square whose bottom edge it lies on within 1e-8 (tilted
1e-9 rad) leaves the square's four 10 mm edges (its corner at x = 4 is within 1e-8 of that
edge's line), and its union runs along y = 0 as one 14 mm edge (the quadrilateral's bottom
edge is within 1e-8 of y = 0 all along): [4, 5, 5, 10, 10, 14];
- the bent plate and the strip under it: their ends on the line x = 150 are one edge from
y = 47 to 80, six edges for every turn and offset tried, the shortest 3.
Fixes prism::planar_tests::overlapping_lines_a_hair_from_parallel_do_not_cross and
a_bent_edge_crossing_its_neighbour_by_their_corner_leaves_no_sliver.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Reading a planar sheet's faces back as regions, each hole went to the smallest outline whose
Loop2::contains held its middle: even-odd against the outline's polyline within 1e-3 mm. A
5e-5 mm square cut 1.7e-4 mm inside a radius-10 circle lies outside the polyline's chords there,
so no outline held it and the cut failed ("face 0 has a hole outside its material"). An
outline now holds a point by its polyline within a quarter of the point's distance from it (its
nearest point on the exact segments), which no chord can pass the point by.
Fixes kernel prism::planar_tests::tiny_tool_between_circle_and_display_chord_is_not_lost.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
94bd8719a (#3730) turned a BREP_WITH_VOIDS void inside out when it enclosed volume of the
outer shell's sign: SOLIDWORKS writes .F. over a void shell already facing into its cavity,
SolidCraft .T. That lived in the truck reader; the schema-4 reader (crates/step) that replaced
it took the flag alone, and the block with a 20 x 6 x 5 cavity read as 15600 (the cavity added)
instead of 15000 - 600 = 14400.
The reader now takes each void's sign from the faces themselves before it orders the record:
the divergence theorem on the record's surfaces and pcurves (sew's face_flux of p / 3, moved
to geom's brep::eval so both use it). A void enclosing volume of the outer shell's sign has its
faces turned over. Flipping on the finished record is not an option: its edges are ordered by
the faces' sides.
Fixes kernel step_in::tests::a_void_reads_as_a_cavity_whichever_way_its_shell_flag_points.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The expected 6703.5222 was a mesh measure (truck). The lid exactly: the 76.8 x 89.3 x 2.4
plate less its four 3 mm corner rounds ((76.8 * 89.3 - 36 (1 - pi/4)) * 2.4 = 16441.2344), the
skirt ring ((71.5 * 84 - 68.5 * 81) * 3 = 1372.5), less the window (68 * 61 * 2.4 = 9955.2) and
the slot (44 * 10 * 2.4 = 1056) through the plate, and the notch through the skirt's 1.5 mm wall
(22 * 1.5 * 3 = 99): 6703.534401. The window and slot lie inside the ring's opening and the
notch above the plate, so nothing else overlaps. SMLib measures 6703.534401575, 2.6e-7 off.
The test now computes that closed form and holds the body to 1e-6.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A whole circle is now one closed rational curve (Loop2::circle is one segment), whose first
control point is repeated as its last: the mean of its nine control points sat r/9 towards the
seam, and a rail scaled each station about that point. A rail bulging from radius 10 to 15
(r = 10 + 5 sin(pi z/40)) then grew the circles as if r = 10 + 5.625 sin, volume
4632.8 pi + 9000 = 23553.9 against the solid of revolution's pi * integral r^2 dz =
4500 pi + 8000 = 22137.2 (+6.4%; the engine's arc rail +6.5%).
The middle is now the curves' centroid by length, integral x ds / integral ds (8-point
Gauss-Legendre per knot span on the rational point's speed): the shape's alone, however its
curves are written; a circle's is its centre. geom's GAUSS_8 is public for it.
Fixes kernel loft_rails_tests::a_bulging_rail_makes_the_solid_of_revolution_of_the_rail and
engine loft_rails_tests::a_rail_turns_a_loft_into_its_solid_of_revolution_and_stretching_is_an_edit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillets/4782-fillet-two-end-verticals-past-a-full-round passes: SMLib (90aabff) refuses
R10 on the 15 mm wide box's two end verticals as too large, and the refusal now names
the largest radius that fits, 7.5 mm (the full round). Run on aarch64 Linux with
--known-failing: every other fillets case as listed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Under the blend-overflow decision (237f0ae74) a convex round running over a face's far
edge (a cliff) is built and cut from the part, so the truck-era fixtures of the reduce
and taper fits (a 2 mm fin, a plate narrowing to 2 mm, a wedge, a 10 mm cube's edge at
R20) no longer refuse their radius and the fits have nothing to react to. Each test now
uses a case SMLib still refuses, and checks the cliff case builds:
- engine fillet_fit_reduce_keeps_the_radius_where_it_fits: a 14 x 6 x 10 post on a
40 x 30 x 20 block, its four verticals at 3.5 (two rounds would cross on its 6 mm ends)
reduced to 3 on 4 of 5 edges, the block's corner kept at 3.5: 24840 - (4 - pi) 90 -
(1 - pi/4) 3.5^2 20. New fillet_fit_reduce_keeps_a_round_over_a_cliff: the fin's R4
builds, nothing reduced, at the kernel's fillet_max_each answer.
- engine fillet_fit_taper_follows_the_room_along_the_edge, spline_fillet_takes_over_a_taper,
kernel taper_follows_the_room_along_the_edge, ui-egui fillet_spline_handle_tests: the
narrowing plate stands against a wall behind its slanted side (z -15 to 30), so its top
and bottom end in concave edges: R3 is refused and tapers 3 -> 1.8 as before. Without
the wall, R3 is cut over the 2 mm top's far edge and kept constant: at x the section
loses (1 - pi/4) 9, or 3 w - (F(3) - F(3 - w)) where the top is w < 3 wide, 6522.7745566.
- The wedge closing to a point: on its own R16 is cut over its cliffs (the section
integral, 4195.578821, SMLib within 4e-8) and kept; its room's taper is checked as a
spline fillet. Against a wall (new fillet_fit_taper_closes_to_a_point) the taper must
close to 0, which SMLib fails today (status 1001).
- kernel taper_mesh_tests: the collapsed taper is built from taper() as a spline fillet.
- ui-egui the_feature_menu_copies_a_warning_message: the 10 mm cube's four verticals at
6 are reduced to 5 (a full round), which the warning says.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's blend-overflow decision (2026-10-25, 237f0ae74): a convex round or chamfer
whose rail runs off its face across a cliff (an opening's rim, a hole, the part's
outline) is built on the faces continued and what it removes is subtracted, so it never
bridges an opening; a round may use up a face; a chamfer of a face's full width stays
refused. These tests still expected truck's refusals. Each now expects the decision's
body, with its answer from the geometry:
- issue_1080 chamfer_into_a_pocket_is_cut_by_it (was ..._is_refused_with_the_size_that_fits):
chamfer 6 into the pocket 4 mm in removes 360 - 20 (its triangle less the part over
the pocket): 14660; 6 along the top and 2 down, 120 - 20/3; 2 and 6, 120.
- issue_1080 fillet_into_a_pocket_is_cut_by_it_and_one_that_fits_builds: R5 removes
(1 - pi/4) 25 along 20 less 10 (5 - (sqrt(24)/2 + 12.5 asin(1/5))): 14893.0344442.
- issue_1080 chamfers_crossing_each_other_are_refused: still refused (they cross);
chamfer_max and fillet_max find 2 mm.
- issue_1080 rounds_on_both_sides_of_a_wall_build_as_one_fillet: R7 alone opens a slit
where its arc passes the inside corner: V0 - (104 (1 - pi/4) 49 - 100 a), a = the square
[25, 30] x [35, 40] outside the circle about (25, 35), 5 (5 - sqrt 24) - (F(5) - F(sqrt 24)):
38458.8958265. Both at R7: the arcs about (25, 35) and (23, 33) cross only outside both
quarter arcs and the inner round's material holds the slit, so V0 - 4 (1 - pi/4) 49 =
39509.9380404 (was expected refused).
- issue_324 a_round_into_a_hole_is_cut_by_it (was the_radius_offered_beside_a_hole_fits):
R4 over the r3 hole: 8000 - 90 pi - (640 (1 - pi/4) - the round's height over the
hole's width, integrated with y = 17.5 - s^2): 7580.2873154.
- issue_851 arc_top_blend_uses_up_the_wall_and_refuses_a_collapsed_one: a round of the
wall's full height uses the wall up (one face for the wall, the removal integrated as for
the other sizes); the full-height chamfer stays refused.
- kernel tests: fillet_max_finds_the_largest_radius_that_works keeps the post (3.5 -> 3)
and the no-edge case; its disc and notch cases move to
rounds_past_the_bottom_of_a_wall_are_cut_from_the_part: the 2 mm disc's R2.5 turned
section, pi (338 - integral of (169 - rho^2) dz), rho = 10.5 + 2.5 cos(theta) (the same
formula gives SMLib's R2 994.15188 exactly), 957.6922389; the notched block's outline
R7, 11925 - (1 - pi/4) r^2 (140 - 8 c), c = r (10 - 3 pi) / (3 (4 - pi)) (SMLib's R7 within
5e-8), and R8 less its part over the notch, integral of 2 (5 g - g^2/2), g = 8 - sqrt(64 - t^2).
- kernel tests: chamfer_wider_than_sloped_basin_rim_is_cut_and_a_full_width_one_refused:
past the 1 mm and 0.5 mm rims the chamfer runs over the slab's front edge and is cut:
the clipped triangle's area (30 + z centroid), its length 60 - h between the sloped end
walls (the same formula gives chamfer_sloped_basin_rim's fitting chamfer to 1e-12);
a chamfer as wide as the rim is refused.
- blend_corner sloped_rim_fillets_stay_inside_the_material, equal_slope_rim_loops_stay_
inside_the_material: R4 and chamfer 2 over the thin rim build, every vertex inside the slab.
- engine blend_fit chamfer_through_the_openings_is_cut_by_them: the report's 9 mm chamfer
is cut by the openings, 3350 (the rig's fillets/1080 case).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since bcbb99005 a blend larger than its faces is SMLib's refusal (KernelError::TooLarge,
"the fillet is larger than the faces beside its edges allow"); truck's room check, whose
words these tests still matched, went with blend_fit. The refusals themselves stand:
- fillet_consuming_a_side_face_makes_a_full_round: R3.001 and R3.5 on the 14 x 6 x 10
box's four vertical edges, past the full round, are refused as too large (no longer
"larger than the neighbouring faces"); the body unchanged is its own volume before
(SMLib's measure of the box is 839.9999999999998, not 840 bit for bit).
- a_chamfer_that_would_grow_the_part_on_a_convex_edge_is_refused: refused as too large;
the word "convex" was the old check's.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
When the kernel's room pre-check went (bcbb99005), a fillet or chamfer refused as
too large stopped saying what would fit: only SMLib's NO_ROOM words were left. The
rig expects the refusal to name it (fillets/4782-fillet-two-end-verticals-past-a-full-round:
"the largest radius that fits is 7.5 mm", fillet_max for the exact fit).
A constant fillet with the exact fit, and an equal-distance chamfer, refused as too
large now add "; the largest radius (distance) that fits is X mm", found by the same
bisection fillet_max runs (up to 16 blends, three significant digits), now shared with
a new kernel::chamfer_max. Where the search itself fails (a candidate failing for
another reason), the refusal is left as it was. The reduce and taper fits and the
kernel's own searches call the kernel blends directly and do not pay for it.
Tests: the 14 x 6 x 10 post's R3.5 names 3 mm; a 4 mm rib's crossing chamfers and
rounds at 3 name 2 mm.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
sweeps_along_paths expected one wall for the circle swept through 41 points of
a smooth curve: a point path is the polyline its points make, swept line by
line and mitred at each point since 43e8b0349 (sweep_path's own test expects
40 + 2 faces since d9274aaf1), so the circle's one segment has a wall along
each of the 40 lines.
The holed square along the L-shaped path expected two faces per segment. The
corner turns the profile about Y, so each line at a constant y (the outer
loop's segments 0 and 2, the hole's 1 and 3) sweeps the plane y = c it lies in
along both legs, and the two walls meet edge to edge on the mitre in that one
plane: one L-shaped planar face. The lines at a constant x sweep two planes,
two faces. check_sweep takes the count per segment.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
sweep_origins read a sweep_path tool's faces by the truck face order (walls in
profile order, then the start and end caps), and fell back to swept_origins,
which names a face without an edge in the profile's plane an end cap. SMLib's
sweep along lines and arcs is made piece by piece and mitred at each corner
(tangency-labs/smlib#43), so most walls start further along the path: 39 of a
44-face sweep came out as end caps (105 of 110 before the previous commit). The
sweep records each face's origin as it builds it (Body::history), and
sweep_origins now returns those, finding by geometry only a face the tool names
no origin for. swept_origins says what it holds for.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A sweep along a path with corners sweeps each run past its corners and cuts it
back to the plane halving the corner. The lead past the corner was the
profile's reach times tan(turn / 2), enough only for a profile square to the
path. A point standing s ahead of the path and w from it needs
w tan(turn / 2) - s past a corner (w tan(turn / 2) + s before one): a profile
at a slant to its path reaches across the mitre by its slant as well, and a run
carried short of it leaves a notch with a piece of the run's section in it.
The section keeps both distances along a run and through each corner (it
turns with the path; a twist keeps them, an end scale grows them by at most
its largest scale), so the lead is taken from the profile's points at the
start, for the plain and the controlled sweep. A profile square to the path
(s = 0) leads exactly as before.
The walls' history seeds sat at the middle section of each run, which for a
slanted profile on a run shorter than its slant lies past the mitres, on the
next run's wall: half the walls came out generated. Each piece's seed now sits
half way along the stretch its own point keeps between the mitres, carried
there exactly along lines and arcs (as SMLib's sweep turning with the path
carries the profile), at the station there in the controlled sweep.
A flat 4 mm square swept along 21 points of a rising sine (provenance test):
110 faces, 66 of them notch faces, and walls left unnamed; now 44 (two caps, the two
walls in the path's plane, a wall of each slanted side along each line), volume
16 cos(slant) L to 1e-6 (new test a_slanted_profile_meets_itself_at_every_mitre).
The square round a closed 122-line polyline (issue_2005
closed_polyline_sweep_shares_its_starting_section): the first section leaned
by half a chord's turn left a 6.2 mm^2 piece of it at the closing mitre, named
the start cap; now 246 faces, every one a wall.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
legacy_internal_capture_refuses_an_uncaptured_source_in_another_component
picked the top Offset Face raised as a face with neither a construction
certificate nor an exact history name (#494), to reach the legacy path
that refuses a profile across components while the source occurrence's
move is uncaptured. Offset Face has SMLib's history since 0f3d6f177 (shell,
offset faces and thicken through SMLib), so that top is now named exactly
(F3:+z#[F3:-x], verified) and capture_face_anchor gives it a lineage
anchor; the legacy path is not taken, and the capture is right to
succeed: an anchored attachment captures its path's pending positions
when it is made (capture_positions).
The test, renamed to what it now checks
(internal_capture_in_another_component_anchors_an_offset_face_by_its_history_name),
asserts the face still has no construction certificate, the capture is a
Lineage anchor on the occurrence's path, and capturing changes neither the
document nor the pending moves.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The test cut three regions from a plate that keeps its meshes and
expected the memo to hold one mesh afterwards: the old kernel's booleans
meshed their operands. On SMLib (ops::boolean -> smlib_boolean, since
42c41464a) a boolean reads the exact record and a tool apart from the
body is found from the exact boxes, so no boolean meshes anything and the
memo is empty after them. The test now asserts that, then that meshing
the kept body twice at one tolerance makes one memo entry, bit-equal to a
fresh mesh, which is the reuse the memo is for.
Fixes kernel body::mesh_memo_tests::regions_cut_from_a_body_keeping_its_meshes_are_unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Split Face records its lines on the body (split_lines): heal and the
certified-planar regularizer keep the faces apart along them, and they
make the body regularization-protected. On SMLib the boolean, the n-way
union and Shell carried the protection over but dropped the lines, so a
body with an authored split lost its record after a Union with partial
contact (issue #674/#782's case), and a shelled one after Shell. Each
result now keeps its operands' lines, each line once
(Body::inherit_split_lines), as the old kernel's coplanar join did.
regularization_protection_tests: SMLib's shell makes no section strips,
so the painted cup no longer has more faces than the ordinary one. The
ordinary cup is the box's five kept faces, their five linings and the
rim: 11. A paint over a whole face authors no boundary inside it, so the
painted cup has the same 11 faces; the split side's line stays an edge on
the wall and its lining: 13. The test now asserts those counts exactly
(it asserted more than 11 for both, the old strip route's witness) and
that the split lines survive.
Fixes kernel issue_674_tests::partial_contact_retains_an_authored_split_away_from_the_contact
and body::regularization_protection_tests::stamped_shell_keeps_authored_painted_and_split_boundaries.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The test helper side_by_side copied the second body's regions by hand,
dropping its voids and keeping its infinite region (region 0) as if it
were a bounded one. Its closed shell was then the outer shell of two
regions, which the portable record refuses ("a closed shell bounds two
regions and encloses one"). The helper now joins the two records with
geom's brep::part::compound, which puts each body's outer shells in the
one infinite region and keeps its bounded regions; the face sources are
still found by plane afterwards, so nothing the test checks changes.
Fixes kernel body::planar_sources::tests::coincident_competing_source_planes_and_tool_planes_stay_unknown.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Body::parts (and so Body::lumps) mapped each piece's faces through the
body's face-source table with a silent `get`, so a table shorter or longer
than the body's faces gave its pieces sources of other faces, or none. The
table is by face position: one whose length is not the body's face count
belongs to another body. The pieces are now refused with "lumps: face
source table does not match the body", as before the SMLib port (the check
went with the old lumps_with_clearance in 66e31bede).
Fixes kernel body::lump_tests::grouping_lumps_does_not_infer_absent_or_misaligned_sources.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Which input plane each result face lies on was found by scanning every input plane whose
normal x was within the resolution's angle: quadratic on axis-aligned parts (two thirds of the
faces have normal x = 0), so it was capped at 16 384 faces a body and 2 M comparisons, and the
join of the 20 level-2 sponges of a level-3 Menger sponge (7 326 faces) was refused past the
comparison budget.
The planes are now indexed by their unit normal, in cells twice the bound on two matching
normals' difference (asin(angular) < 2 angular), and in each cell by their offset from a common
centre, searched in the window linear + |a.o - c| |n_b - n_a| that
d_b - d_a = (b.o - a.o) . n_b + (a.o - c) . (n_b - n_a) gives, plus rounding slack. The index
offers a superset; same_support still decides each match, and candidates are taken in the same
order as before, so every answer is unchanged. A plane with a normal not of unit length is
offered to every query. Both caps are removed: results are bounded by inputs capped where they
entered. The descriptor-size budgets on kept roles are unchanged.
Rig, --known-failing, results compared case by case with develop's: booleans (129) and shell
(28) identical except booleans/5126-join-menger-sponge-level-3, which now passes in 38.9 s on
aarch64 and leaves KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
outer_area, which decides whether SMLib's normal is the record's for each
face, copied every edge of the body into a record for each face before
computing the pcurves of that face's outer loop: O(faces x edges) curve
clones, on every operand and every boolean result. pcurves now takes an
edge lookup instead of a slice of edge records, so outer_area reads the
loop's edges where they are. The pcurve routine gets the same curve,
interval, tolerance and trims as before, so every area, face turn, record
and numbering is bit for bit what it was.
On the level-4 Menger sponge with 3 tools, body_from_smlib_ordered goes
from 92.6 s to 1.3 s of self time.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
explode.show put the view's placements in the uncaptured moves, so occurrence.properties reported
the exploded placement and Capture Position (and reparenting, moving bodies between components,
copying or pasting in place, URDF export) wrote the view's offsets into the design. The session
now records which uncaptured moves are the view's (Session::exploded); what reports the design's
placements or works a new placement out from them uses the design's own moves
(uncaptured_moves, design_document), while the viewport and picks still show the view.
New case cov-explode-show-keeps-the-placements: the arm's properties are the same before, while
and after the view is shown, and Capture Position keeps nothing. The two explode cases that read
occurrence.properties while exploded now expect the design's placement, centre (20, 0, 5), as the
command says ("shown only; the design keeps its placements").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The curves were held on a 1-2-5 ladder from the world origin, so count 3 on a 40 x 30 face gave 3
one way and 2 the other. They now follow the command's contract: the held parameter at
lo + k (hi - lo) / (count + 1), k = 1…count, over the face's extent. Faces of the body on the same
surface record are spaced together over their combined extent, so a face a boss splits still
shows the same lines straight across the split.
New case cov-isocurve-40-by-30-face-count-3: x = 10, 20, 30 and y = 7.5, 15, 22.5, to 1e-9 mm.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Both walked the picked curve's display polyline: a point a third along an R10 sketch arc was
0.87 µm off (8.6603, 5). They now evaluate the path's exact curves by arc length: lines and arcs
in closed form, a free-form span at the parameter its arc-length integral reaches (body edges by
their record curves, 3D sketch curves by their arc, spline, line or linked exact curves; only a
curve that exists as points alone, an intersection edge or a projected curve, runs along them).
The arc's point is now within 1e-12 mm of (10 cos 30°, 5, 0).
A t outside 0…1 was clamped silently, which the contract (`t: expr, 0…1 along it`) does not
say: it is refused ("t is 1.5: a point along a path is 0 (its start) to 1 (its end) of the way
along it"). The construction cases grade the arc and line to 1e-9 mm, past-the-end is refused,
and a new case takes the middle of a symmetric cubic spline, (20, 7.5).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A face of degree 1 in one direction (an extruded spline) was refused with "a fairness term does
not fit the net's degrees": the thin-plate energy's S_vv asks for second derivatives a linear
direction does not have. On every span that term is exactly zero, so it is dropped; the energy is
the bending along the curve and the twist. A face whose held layers are its whole net (a
single-span cubic with its edges kept, an extruded curve's two rows) has no interior control
point: it is left exactly as it is, its energy reported unchanged, 0 steps.
cov-fair-single-span-face-has-nothing-free-to-move passes and leaves KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The portable record's 4,000,000-item budget refused a real result: the join of a level-4
Menger sponge's level-3 sponges ended with "SMLib export: the mapped B-rep does not validate:
portable B-rep: item budget". The budget guards records from outside the kernel, and a body
the kernel built in memory from inputs already bounded where they came in isn't hostile.
Brep::validate keeps the budget for records read from outside: native design caches
(decode_native_body, behind its own 256 MiB, 1M-per-array and 20M-value caps) and STEP import.
The new Brep::validate_built runs every other check, without the cap, on what the kernel
builds: SMLib's export of an operation's result, a body's record (Body::from_record, after
the decoder has checked a file's), a part of a validated record, the record handed back to
SMLib, and the validity check. Its checks are linear in a record already in memory.
SMLib's export bounded its counts by the same budget; a count is now bounded by SMLib's own
longest array (flat::MAX_LEN, checked on entry), which keeps every offset worked out from
the counts from overflowing, and the redundant topology-length cap goes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Where a round meets a plane it is only tangent to it: its curvature jumps by 1/r there, so no
corner patch can be G2 to both at that point. The cases graded the whole seam and could not pass.
They now bound the curvature jump at stations clear of each seam's turn, within reach of the
corner, scaled by r (ladder 07/019's bound at r5): r1 within 2.2 mm, 0.24 mm clear, 0.005 per mm;
r5 within 11 mm, 1.2 mm clear, 0.001 per mm. Develop's corner gives 0.00135 and 0.00027 per mm
(the jump at the vertex is 1.017 and 0.2035, the round's own 1/r), so both leave KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
When a − b or b − a cannot be made (a kernel error, or a body that encloses no volume), the
region's volume and centre are null, measured_by is "not measured" and not_measured gives the
cut's error; its deviation, area, faces and box are still given, the side's total is null and
the verdict says the volume is not measured. The integrated-along-lines estimate is no longer
reported as a volume.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
inspect.compare integrated a region's volume along sampling lines: the
40 x 30 x 5 slab between a box and one 5 mm taller came out at 5976.49 mm3
against 6000. The regions are still found from the two surfaces; each one's
volume, centre and box now come from the pieces of the exact cut a - b (or
b - a) that lie there, measured as inspect.measure measures a body
(measured_by: boolean). Where a cut cannot be made the region keeps the line
integral, marked measured_by: lines, with a warning. The rig case
cov-compare-taller-box passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
inspect.center_of_mass measured each body's display mesh, so a cylinder r 5,
h 10 came out at 784.13 mm3 against 250 pi = 785.40, and the answer moved with
display quality. It now takes the exact mass properties inspect.measure uses
(ModelBody::measure), skips bodies that enclose no volume as Measure does, and
lists what it skipped. The rig case cov-center-of-mass-box-and-cylinder passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- #58: a fillet's tangent-point step no longer depends on the blends before it (solidcore #1173).
- #59: the fillet clean-up keeps the target's edges and faces by a mark, not by address (#1176).
- #60: capi test, a line projected through a sphere's poles meets itself smoothly at each pole.
- #61: offset faces removes a step wall the move closes to nothing and merges the two tops, so
shell/cov-replace-face-step-onto-the-higher-face builds.
- #62: thicken puts a flat side wall on its plane (solidcore #1599), so a cylinder sheet's end
rings are planes: surfaces/cov-thicken-cylinder-sheet-symmetric-tube passes.
Both cases leave KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
They fail on develop today (4 native tests, 8 of 83 reference cases), so running them on pull
requests would fail every pull request. Back on pull requests once develop is green. Reverts
0cdc25094.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The single results form compares a whole number exactly (a count). The construction and inspect
cases gave positions and volumes as whole numbers, which the form they were written for compared
within tolerance; they are decimals now. The NPT groove fix makes ladder 06/023 pass: its golden
entry is the passing run (51 faces, 8226.4042 mm3).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The shared core (crates/smlib, the grader, doc eval.rs, engine features.rs and the kernel's core)
is in PATHS-ALL; the new areas' copies of it are dropped, so an area reruns on its own files and the
core reruns them all. sheet-metal also watches the sheet commands, the sheet document and the DXF
writer. 116 commands a case now uses leave EXEMPT; 25 geometry commands are still to cover.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Two branches added a results field in different forms ({step, json} and {command, pointer,
value}). The grader keeps one: a 1-based step, an optional JSON pointer into its answer, and the
value matched as files are, with an optional relative or absolute tolerance. The construction and
inspect cases are rewritten to it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>