* claim: #10688
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Feature editor: Undo, Redo and the History bar cancel an open editor first (#10688)
Undo, Redo and History steps changed the design under an open feature
editor, whose OK and Cancel then refused it. They now cancel the editor
first, putting its marker back, as starting another tool already does.
While an editor is still opening they wait for it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #10316
* Insert Part: ASME/ANSI inch hex cap screws, hex nuts and SAE/USS washers (#10316)
Part of #10316. New standard-part families, tabled in inches as the
standards give them and built in millimetres: hex cap screw (ASME
B18.2.1) and hex nut (ASME B18.2.2), 1/4 to 1 in UNC and UNF from the
thread catalogue, and plain washers SAE and USS (ANSI B18.22.1 Type A).
Cap screws take the standard inch lengths, 1/2 to 8 in, defaulting to
the first at or above 2.5 d.
Lengths read as fractional inches in Insert Part, Change Part Size, part
names and part numbers. Insert Part gains a Unit system list (Metric,
Inch) above Type; it opens on Metric. parts.library reports each
family's system.
Inch parts get no cosmetic thread: solid.thread takes only metric
designations (#9571), and the old path would have made a wrong metric
mark. 9/16 waits for the thread catalogue; split lock washers and
carriage bolts follow in later PRs.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #8822
* Tangent Plane: line it up with a reference plane, at an angle (#8822)
`construct.plane.tangent` takes an optional `reference` (a plane or planar
face) and `angle`. On a cylinder, cone or torus the plane touches where the
face turns towards the reference, turned by the angle about the face's axis,
on the side of the pick; on a sphere it is parallel to the reference. The
plane follows the reference when it moves. The Tangent Plane dialog gets a
Reference plane input and, once one is picked, an Angle field; editing the
plane brings both back. Saved as a pending format change.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Ambient occlusion: the radius follows what the frame draws (#9327)
In an empty design the radius came from the model's box, which is empty, so a
preview got the smallest radius and the depth map's precision showed as specks.
It now comes from the box the depth range uses, and with nothing to draw there
is no occlusion.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Ambient occlusion: the term drawn once and blurred by depth (#9327)
The lit pass worked the term out for every fragment it shaded, under a pattern
that changed from pixel to pixel, which read as grain. The term now has its own
texture, drawn once for each pixel of the prepass, with a fixed 4 x 4 pattern, and
a 4 x 4 blur that keeps to each pixel's plane takes the pattern out without
crossing an edge. The lit pass reads the result. The prepass and the term share
their pipelines and draw walk.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #10675
* agent chat: Copy message on each sent prompt and assistant text block (#10675)
A visible Copy message button on each copyable transcript message and a
right-click menu with the same action. Assistant replies copy their
original Markdown, prompts copy the text as entered; picture-only prompts
and thoughts get no action. Hover-only message areas keep partial text
selection working.
* agent chat: complete Copy message locales and tests (#10675)
* agent chat: route the message copy menu through ui_kit::Container (ui-containers gate)
---------
Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
* Sketch: Remove Spline Point takes one fit point out of a spline (#10783)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Sketch: Remove Spline Point takes one point out of a spline (#10783)
sketch.spline.remove_point takes one fit or control point out of a
spline. The spline keeps its id and runs through its other points, which
stay where they are. The point goes with the constraints on it, unless
another curve uses it. A closed spline's closing point, an end joined to
other geometry, the last 2 points (3 when closed), and projected, offset
or patterned splines are refused with a message.
The right-click menu of a spline point, picked alone, offers it beside
Reverse Spline Direction.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude <noreply@anthropic.com>
* claim: #9874
* Add shared Preferences cards, figure painters and gallery entries to ui_kit
* Preferences: Arabic, Hebrew and Vietnamese carousel labels
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Use the app's selection colours in the Preferences cards
* Measure Preferences figure inks and use shared palette metrics
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Colour popover: a held step button keeps stepping, and R, G and B have tooltips (#10201)
The step buttons beside each colour number sensed clicks only. egui
stops counting a press as a possible click once it outlasts its longest
click (0.8 s), so the held button stopped repeating after 8 steps. They
now sense drags too, which keeps a long press down on the button until
it is let go.
R, G and B now carry tooltips (Red, Green, Blue) as H, S and V already
did: a single letter doesn't name the colour in every language.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Colour popover: the R, G and B tooltips in Vietnamese too, a complete catalog (#10201)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* ui_kit: search_picker, a filtered dropdown with a custom entry
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Agent chat: endpoints list their models with names, say when listing fails, and OpenClaw and OpenRouter presets (#2582)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Agent chat: a typed model goes to endpoints and to agents that offer a model option
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Agent chat: the header's model pickers search and take a custom model
The popup can't grow once it is open, so search_picker now fixes the height of what changes below
its box when it opens: the custom row or a late list could otherwise end up out of reach.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* AI preferences: pick an endpoint's model when adding it and on its card (#2582)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Agent chat: model picker rows read from the left, and a refused typed model says which
From running it: list_picker centres its text, which reads badly for a long list of ids, and an
agent's own refusal can say no more than "Internal error". The search box also asks for a repaint
while it waits for the focus, so an idle window does not stop short of it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Agent chat: docs for the model picker
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Agent chat: an endpoint's answer that is no model list says so, an empty list too, and editing lists with the kept key
A 200 without a `data` array (a web page where the endpoint should be, as OpenClaw's gateway
serves until its chat endpoint is enabled) was cached as a successful, empty listing, so the
picker stayed blank with nothing to say and never asked again. Now it is an error with its own
note, an empty list says so, and both are asked for again the next time.
The Edit dialog lists its endpoint's models when it opens, with the kept key read from the
keychain on the listing's thread, as the card does; the key stays out of the field.
The method-not-found test expects the refusal notice that names the model, as every refused
model gets since this branch.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
* Agent chat: models from several providers fold under their providers inside the picker
As Chemiseblanc does in #10187: with two or more groups, `search_picker` draws each group as a
header with a chevron, the name and how many of its choices are listed, and a click folds or opens
it. Before anything is typed only the current value's group (and the one the caller asks for) is
open; a group with a match opens once something is typed; a fold made by hand stays until the popup
closes. Enter takes the first row shown, so never one folded away. A lone group keeps its plain
heading.
The header's model picker feeds its providers in as groups, so the separate provider drop-down
goes; the control channel's `provider` now says which group opens first. A header click gives the
focus back to the search box, so typing goes on filtering.
The dialog's listing test checks what kind of listing it got rather than translated words, which
the listing thread may render in another language than the test's.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
* Agent chat: rustfmt the provider groups
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
* Agent chat: an endpoint's models named `Vendor: Model` fold under their vendors
OpenRouter lists `openai/gpt-6.1-terra` as "OpenAI: GPT-6.1 Terra". A listing whose ids read
`vendor/model` and whose names read `Vendor: Model` now names its providers, so the picker folds
it under its vendors like a multi-provider agent; the rows read the model's name, and the id stays
in the tooltip and in the search. An agent's own `Provider: …` word still comes first. One vendor
is one flat list, as before.
The Add dialog's picker has no current model to prefer, so with nothing to prefer every group
starts open; folding is a click away.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #1486
* Compare picture: overlap and edge offsets of the model against a reference picture (#1486)
inspect.compare_picture lays the model's silhouette over the part found in a
PNG or JPEG and slides it to the best overlap: overlap (0..1), the model's
edges against the picture's in mm at nine stations, and an overlay PNG. The
MCP tool compare_picture runs it and hands the overlay back as an image block.
inspect.silhouette grows a reusable silhouette::outline for the model side.
* chore: re-trigger checks (defaults line already present in PR body)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* i18n: carry the Compare Picture label in Arabic, Hebrew and Vietnamese too
The complete-catalog guard (every_complete_catalog_carries_every_english_message)
failed because the pending file covered only en/ja/zh; ar, he and vi are
complete catalogs and need the key as well.
* Compare picture: one uniform scale, capped fit, sturdier part finding
Review on #6416: fit no longer stretches the axes apart (width is the default,
both scales uniformly by width and reports aspect_mismatch); the fitted model
takes the same MAX_GRID cap as the picture; the border flood seeds only from
border pixels near the border's main colour, reads alpha, retries at a
stricter step, and says which case failed; the slide searches the whole
placement range instead of a tenth around the centre; the model's holes get
the picture's fill rule; crop becomes crop_px / crop_fraction with explicit
units. Pins #1486's bracket (overlap 0.865, bottom -10 mm at the upright) and
adds a regression test per problem.
* Compare picture: alpha only for a see-through border, part_fills_crop, outline-only wording
Review re-test on #6416: one translucent backdrop pixel no longer switches the read to
alpha — alpha decides only when most of the border is see-through, and any ink is then
part, so a part drawn at alpha 100 survives; part_fills_crop: true takes the crop box as
the part itself, for one view cropped tight off a board where the part takes most of the
border and the flood would keep the backdrop strip instead; a third backdrop pass compares
each pixel to the border's main colour, so a white part on (245, 245, 245) JPEG at quality
75 separates; the command, tool and docs descriptions now say the compare is outline only:
holes are not compared. A banded light backdrop stays a follow-up. A test per case.
* MCP compare: format the picture tests
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* Render results: keep up to eight completed renders and select or discard them
* Render results: Live and render compare with a divider, and render all shots
* fix: use comparison theme tint and reveal reset test targets
* fix: restore Unicode expectations in render workspace tests
* claim: #9111
* Preview: new surface is tinted whatever its size, and the tints can be turned off (#9111)
A preview decided which faces of a changed body were new surface by asking
whether their triangle centroids lay on the old body, within a tolerance that
follows the part's size. A round or chamfer small beside the part never leaves
that tolerance, so it was drawn as if it had always been there, and sampling at
a fixed step told alike faces apart by nothing but how many triangles they had.
The kernel already records which faces an operation generated, so `build` takes
that record alongside the geometric test. The test stays because a body carries
the history of whatever last made it, which is not the previewed operation when
a parameter change re-evaluates the design: the record only ever adds faces to
the answer. The vote itself now asks about every centroid of a small face,
spreads a large face's samples without a resonant step, and calls a face new
above an eighth of its samples, which a blend tangent on both of its sides
reaches with the one row of facets in five that is clearly off the old surface.
Graphics gains two settings, both on as they come, so nothing changes out of
the box: Tint new surface in a preview draws a changed body as itself when it
is off, working out no face at all, and Show removed material in red leaves the
see-through cut and the ghost of the shape a feature replaces fully
transparent, drawing only their outlines.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5 <noreply@anthropic.com>
* claim: #9084
* Edit Extrude: close on the first Escape (#9084)
An edit dialog whose value names a parameter (`T` in Edit Extrude) opened with
that field focused and its completion list showing the longer names (`tan(`),
unarmed. The list took the first Escape, so the dialog needed two.
An unarmed list now leaves Escape to the window until the box is typed in, as
it already leaves Enter and Tab; once typed in, Escape dismisses the list first
as before. Its hint drops "Esc dismiss" in that state.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #9827
* Sketch Offset: an Instances count stacks offsets one behind another (#9827)
Offset made one offset at a time, so a set of evenly spaced outlines meant
running it again on the curves it had just made, once per ring: a separate undo
step and a separate driving dimension each time.
`sketch.offset` now takes `instances`, a whole number or a unitless expression
from 1 to 100 (1, today's behaviour, by default). The per-group work the command
did inline becomes `offset_rung`, and `offset_ladder` runs it once per instance,
each rung offsetting the one before it the same distance again, so instance n
stands n distances from the curves picked. Every rung of a side is driven by
that side's own dimension, so editing it moves the whole set and keeps the
spacing even, and each side of a Two Sides or Symmetric offset grows its own
ladder. A rung the shape has no room for refuses the whole command and names
which instance it was.
A later rung reads its side from the geometry, through the rung's own
normal-distance annotation, rather than from the distance's sign: an output's
stored ends need not run the way the chain through them is walked, and a
reversed walk reads the same sign as the other side. A circle is the exception
and keeps the sign, because it offsets concentrically with no chain to walk, and
a step past a ring smaller than the distance lands beyond the centre, where the
circle's "outside the current radius" side test reads as the outward side: an
inward ladder turned round and grew again (1, 4, 1, 4 mm) instead of running out
of room.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
* Sketch Offset: the Instances row in the offset window (#9827)
The offset window gets an Instances row under Distance: a whole number with step
arrows, 1 by default, so the count can be walked up a ring at a time and the
preview follows each step. The count is not kept in the design, as Mirror's and
Scale's values are not, so the window sends the number it evaluates to rather
than the text.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
* UI kit: a count's step arrows are not text (#9827)
The arrows stand inside the editor, which asks for the text cursor across its
whole rect, so hovering one showed an I-beam and the arrows read as part of the
number. They take the ordinary cursor back after it, and the pointer is read
from the arrow's rect rather than from the hover the editor underneath competes
for, which keeps the hover highlight in step with it.
The pattern Quantity rows share this field and had the same thing.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
* Sketch Offset: Instances label in the complete catalogs and the other shipped languages
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Sketch Offset Instances: translations for the complete catalogs
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
File › Export STEP…, STL…, 3MF…, OBJ… and URDF… were UI actions around
the shared file.export, so Keyboard Shortcuts had no row for them.
file.export_step, _stl, _3mf, _obj and _urdf now do what those items do
when started from a key, command search or the menu (a save picker; Save
As Mesh for STL and 3MF), and take a path when called with JSON. The File
menu shows their keys. Each has a contract and a reply type
(schema/file.rs).
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #10393
* Per-component History hiding: flag, commands, Browser menu, bar toggle (#10393)
* Carry the new History-hiding strings in the complete catalogs (#10393)
---------
Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
* Sketch: a construction line with a length can be a normal line (#10258)
`construction: false` on a construction line command that has a
`length` makes the segment a normal sketch line, ready to close a
profile, instead of construction geometry. The default stays
construction, and an infinite line is always construction.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Sketch: a length box in the construction line tools (#10258)
The horizontal, vertical, parallel and perpendicular construction line
tools show a Length box beside the pointer from the start. It stays
empty (shown as infinite) and leaves the keyboard to the tool's
shortcuts until a digit is typed; then the box takes the keyboard.
Without a length the tools work as before: one click, an infinite line.
With a length the first click sets the start and a second click the side
the segment runs to, sent as the command's `length` and `near`, so the
segment gets its length dimension. The angle tool has a Length box
beside its Angle box. A typed length keeps the start's snap, and the
preview draws the segment the click will create.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Sketch: a construction/normal switch in the construction line tools (#10258)
A Construction | Normal switch sits under the Length box of the
construction line tools. Normal sends `construction: false`, so a
segment with a length becomes a normal sketch line, ready to close a
profile, without converting it afterwards. The switch starts at
Construction with each start of a tool. An infinite line is always
construction, so without a length the switch is greyed out and its
tooltip says why. It belongs to the tool alone: the Sketch Palette's
drawing line type (X) is left as it is.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: Move: say a part's joint conflicts instead of 'no movable joint axis'
* Move: say a part's joint conflicts instead of 'no movable joint axis'
When a joint of the selected part conflicts with the others (the solver
can't close its loop), Move found no axis and said "This part has no
movable joint axis.", pointing at joint types and limits. It now names
the conflicting joint and suggests editing, suppressing or deleting it.
Parts with no free joint value and no conflict keep the old message.
Refs #10331
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Markus Kaltenbrunner <kaltenbrunnermarkus@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Configuration rules: Then says it lists only the table's columns, and how to add one (#10532)
A rule drives or restricts a column of the table only, so Then leaves out a
feature without a Suppress column or a parameter without a column, where
When lists them all. A note under the list now says so and points at Add
Column.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Configuration rules: the two notes in the complete catalogs (Arabic, Hebrew, Japanese, Vietnamese, Chinese)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #10483
* ViewCube: an option to invert the curved roll arrows (#10483)
A new Navigation preference, "Invert the curved roll arrows"
(invert_curved_roll_arrows, off by default): with it on, the two curved
arrows at the cube's corner roll the view the other way within the
screen plane - the clockwise arrow rolls counterclockwise and the
counterclockwise arrow rolls clockwise. The sibling of the cardinal-arrow
inversion from #10286, which left these arrows alone.
---------
Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>