Commit Graph
3133 Commits
Author SHA1 Message Date
jyvikoandClaude Opus 5.5 e7994d48cc Tapped holes: Rc and NPT take the tap maker's tabulated drill
The Rc and NPT drills were rounded to a drill series from a third-party reproduction of DIN 345
and a fractional/letter inch series cited from memory. They now come from the same tap maker's
catalogue the G and Rp drills do: Yamawa YEU23, printed p.709 (Rc, the maximum straight bored
hole with non-full threads, Rc 1/16 to 4) and p.710 (NPT, the maximum straight bored hole, 1/16
to 3). A size its tables lack (Rc 5 and 6, NPT 3 1/2 to 12) is refused as a tapped hole, naming
the range. The dialog's tooltip keeps the standard's minor diameter where the thread ends.
Rc 1/2 drills 17.6 mm (minor 17.807), 1/2 NPT 17.60 mm (minor 17.473).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 b6c3b32a98 Tapped holes: an Rc or NPT hole takes the stocked drill under its standard minor
An Rc or NPT hole was drilled to the exact minor diameter where the thread ends, a size no shop
stocks. It now takes the largest stocked drill not larger than that: metric drills of the DIN 345
series for Rc (to 100 mm), letter and fractional inch drills by 64ths (to 1 1/2 in, ASME B94.11M)
for NPT; past the series it is bored to the exact value. The Hole dialog's drill shows the inch
size for NPT, and its tooltip the exact standard value. Rc 1/2: 17.807 mm, drilled 17.75 mm;
1/2 NPT: 17.473 mm, drilled 11/16 in (17.4625 mm).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 376a91ad75 Hole presets: a modelled tapped thread and its End, and every catalogued size
A preset's thread options save `modeled` and `ease_out` (a named ISO 3508 runout or the fade's
length, kept portable as the other lengths are) and recall them into the dialog. A runout
without a modelled thread is no preset's. Recalling checked the thread with the metric parser
only, so a UNC, G, Rp, Rc or NPT preset was refused; it checks the tapped-thread catalogue now.
An older preset without these options recalls as before: listed, square.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 72e0e00940 Ladder 06/017: the golden entry from a run of the case
Ladder 06/017's golden entry was edited by hand when the chamfered tip moved to ISO 724's d3.
Re-measured by running the case (solidcraft-cli kernel-cases on SMLib): its counts, area and
volume are the ones written by hand; its time is the run's. The tier's order by time holds.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 9717fab2f3 Tapped holes: Rc and NPT, and a modelled thread with the thread's End
The tapped-hole catalogue takes ISO 7-1's Rc and ASME B1.20.1's NPT internal taper threads,
every size of the tables a modelled thread cuts. Their drill is the internal minor diameter where
the thread ends (the reference plane's minor at the face less the 1 in 16 taper over the useful
or effective thread length), derived from the standards rather than a tap maker's table. An
external R is still no hole's.

A tapped hole's options mirror the thread's: `modeled` cuts its thread into the wall, from the
entry, by the same cut as `solid.thread` (now one function both call), and `ease_out` fades its
inner end out before the bottom (ISO 3508); without it the groove stops square at the thread
depth, clear of a blind hole's bottom. The Hole dialog's Tapped rows add Rc and NPT, Modeled
and the End choice (Square, Fade, Fade Length). The format notes in pending/thread-ends.rs and
pending/pipe-threads.rs record the new keys and sizes.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 80e47130b9 Thread: the pipe forms in the dialog, ISO 7-1's Rp, a chamfered tip on a taper thread
The thread dialog offers the pipe threads: G (ISO 228-1), Rp (ISO 7-1), R and Rc (ISO 7-1) and
NPT (ASME B1.20.1). Their sizes are listed by designation without a pitch, one start and a hand
of right or left; a size picked for a hole the dialog sized Rc stays Rc.

Rp, ISO 7-1's parallel internal thread an R screws into, is a form of its own (`rp`): the
parallel profile (H = 0.960491 P) at ISO 7-1's gauge diameters, refused on a shaft. Its cut
meets the analytic material of its profile within 1e-5, as G does.

A taper thread takes a chamfered tip: each end's cone is measured from the major diameter the
taper has at that end. Pipe threads are not ISO metric, so they give chamfer_depth.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 3865982820 Thread dialog: the Ends section is Start (None, Chamfer) and End (Square, Fade)
The thread's start is its free end: it runs off plain or chamfered (ISO 4753). Its inner end
stops square in its own profile or fades over a length; an empty Fade Length is ISO 3508's
runout (2.5 P, or 1.25 P for a thread saved short). A thread saved chamfered at both ends keeps
that. "Square" is its own message (thread.end_square), apart from the geometric square. The
new labels are in en, ar, he, ja, zh, de and ko; Extent, Ends, the chamfer labels and the ISO
4753 hint come from the catalog entries already on develop.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 5fe141c0f9 Thread: the start never fades; ease_in is gone
A thread's start runs off its free end, plain or chamfered; only its inner end fades out
(ease_out) or stops square. The `ease_in` field, the command parameter (refused now, naming
ease_out), the dialog's Ease In row and their docs are removed; `pending/thread-ends.rs`
drops a saved `ease_in` as the design opens. The runout test covers the short, standard and a
sub-turn fade at the inner end.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 361b35afee Thread: a shoulder thinner than the overrun's reach is still a shoulder
The free-end test looked for material 1 to 1.5 pitches past the face's end, beyond the first
pitch so that a chamfer the groove runs out through counts as free. A plate thinner than that
(a boss on a 1 mm plate under M10) had none there, so its top was taken for a free end and
the groove's one-pitch overrun cut into the plate (15 mm³ of a 1 mm plate).

An end is now closed when, over the overrun's whole reach, material lies outside the face's
cylinder (inside it, for a hole) at the radii the groove cuts beyond the face: a shoulder,
plate, head or blind bottom, however thin, steps out past the face, while a chamfer, neck,
countersink or counterbore steps the other way. The band test beyond the first pitch stays
for a cylinder that goes on past a split.

The regression test builds the boss as the app does (a rounded plate, a circle sketched on its
top face, extruded with Join) on 6 and 1 mm plates.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 75deb73aa7 Thread: ISO 228-1, ISO 7-1 and NPT pipe threads, taper threads by a radial law
Three forms: `bspp` (G, ISO 228-1, 55° parallel), `bspt` (R external, Rc internal, ISO 7-1,
55° taper 1 in 16) and `npt` (ASME B1.20.1, 60° taper 1 in 16). Their sizes are tabulated
from the public sources: ISO 7-1:1978 Table 1 (its gauge-plane diameters are the G sizes)
and NBS Handbook H28 (1957) Table VII.2; tests check every row against the standards' own
relations.

A taper thread starts at its free end with its standard diameter there (external: the gauge
diameter its gauge length in, internal: at the face). Its groove is the screw sweep with the
section moved 1/32 of the axial travel off the axis (the radial law the runouts use, added to
it), its section reaching just past the crest, and the material beyond the major cone (or
inside the minor cone) is cut with it, as a die or tap cuts the crests. An external one runs
its standard length by default.

The volumes are checked against the profile's material fraction integrated over the tapered
radii: G 1/2 to 2e-6, R 1/2, Rc 1/2 and 1/2-14 NPT within 0.2 % of the cut.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 2c4212c042 Thread: the chamfered tip at the start or at both ends
`tip` was none|chamfer, chamfer cutting every free end. It is now none|start|both: `start`
chamfers the end the thread starts from, refused when that end is not free (a shoulder, or a
stop inside the face), and `both` every free end as `chamfer` did. The dialog's Tip pick offers
None, Start and Both; `tip: chamfer` in a command names its replacements.

The thread's end options (runouts, tip, chamfer angle and depth) came without a format
change file; `pending/thread-ends.rs` records them and rewrites a saved `tip: chamfer` to
`both`.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 a30a85698f Thread: the chamfered tip reaches ISO 724's external minor diameter
ISO 4753's chamfered end bounds the end's diameter by the minor diameter. The default took the
modelled root (the basic d1) for it, so the cone's small circle lay on the root cylinder and
the chamfer ring pinched to nothing wherever the groove reached the end. The default is now
the external minor diameter d3 = d - 1.226869 P of ISO 724, below d1: the cone crosses the
root, each end is a whole disk of d3 inside a whole conical ring. ISO 4753 is for ISO metric
threads; the other forms, whose root is already their design minor, give chamfer_depth.

Ladder 06/017's analytic volume follows (1945.354522563); its golden entry re-measured.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 d1a8f0417f Thread: a boss thread keeps clear of the plate below
A regression test for the groove stopping at the plate's top: the boss loses the
closed-form volume and the plate keeps all of its 9600 mm³, with and without a runout
and a chamfered tip.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 81ecc872f5 Guide: the Fillet dialog's Type and Corners in their new words
Curvature continuous is the Type entry's name; Corners (Ball, Smooth patch) and Setback are
described with the command words they write. The codes (G1, G2) stay in the text, where they
explain the words.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:01:05 -04:00
jyvikoandClaude Opus 5.5 28e3b8a192 Continuity in words: surface dialogs and Continuity Analysis show no G codes
Patch, Boundary and Blend Surface list Position, Tangent, Curvature and Curvature change; each
order's code (G0 to G3) and what it means is in the row's hover text. The Continuity Analysis
legend, its seam markers and its status line use the same words (Crease for a G0 seam). The
segments now draw their labels translated. The new labels carry over each catalog's existing
translation with the code taken off, so no language loses its wording; a word another label
already translates keeps that translation.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:01:05 -04:00
jyvikoandClaude Opus 5.5 1acbe2806f Fillet dialog: plain words for continuity, Corners with Setback out of Advanced
The Continuity G1|G2 control repeated Type (both set `type`) and G1 silently cleared the
corner; it is gone, and Type names the section in words: "Curvature continuous", its code (G2)
in the row's hover text. The vertex choice moves out of Advanced as Corners: Ball | Smooth
patch, shown only while the edges have a corner where three or more rounded edges meet (or the
fillet already has a smooth patch), enabled for Constant radius with Exact fit and saying why
when not. Smooth patch shows Setback: one distance for every corner, sent as `setbacks` at each
corner's vertex; left empty, the command's default (1.5 x the radius) applies. A fillet saved
with setbacks reopens with them: one distance at exactly the dialog's corners shows in Setback,
any other list is kept as saved. "Smooth" in Variable Radius is "Smooth radius change". The
stale "G2 corner construction is not supported yet" tooltip and the "Fit and G2 corners" note
are replaced by new messages (en, ar, de, he, ja, ko, zh).

No command parameter changes; saved designs open unchanged.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:01:05 -04:00
jyvikoandClaude Opus 5.5 676919d4d6 tess: a face no method plans is filled leniently in (u, v), and named in the stats
A face whose boundary crosses itself in (u, v) (a cusp, a sliver whose sides
sag across each other) was an error, and the body had no display plan. It is
now planned once more with a lenient constrained Delaunay in (u, v): sides
crossing one already kept are left out, the rest is seeded and refined as any
face, and its points lie on the surface, where the GPU evaluates them. The
display has no hole, but the face is still a defect upstream, in its pcurves
or seams: PlanStats::lenient names it with the strict plan's refusal, and the
display plan logs a warning for each such face, so it is never silent.

The face boundaries keep coming from the exact pcurves (d61efb306); cdt::Fill
gets its `lenient` field back (dropped in 3f2585569). The old flat fill (#4021,
tess/fallback.rs) stays gone: develop removed it in 9138e8704. A face the
lenient fill refuses too (loops that do not close in (u, v), or wind round a
seam or pole) stays an error naming the face. Closes #4453's intent on develop.

(cherry picked from commit 84de5aa071)

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 12:24:16 -04:00
jyvikoandClaude Opus 5.5 4f6f254d04 smlib: a setback left open is a profiler span like every other SMLib call
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 8555754730 SMLib: the prebuilt with setback-open corners and the refused-corner index
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 b2fc5e1fbf smlib, kernel: a refused setback corner is named by its point and why
SMLib's out_failed_corner reaches Rust as Error::CornerRefused { corner }, and the
kernel names the corner by its point: a G2 fillet at a corner of mixed convexity
says where it is and that SMLib sets back only corners whose rounds are all
convex or all concave. Engine test checks the message through solid.fillet.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 ba38fbd2af kernel-cases: ladder 07/019, a concave corner's G2 patch
The inner corner of a 20 x 20 x 10 notch in the 60 x 40 x 20 box, three
concave r5 rounds with corner: g2: one valid body of 13 faces within the box,
the patch's twelve seams jumping at most 1e-3 per mm clear of the hole's six
corners (2.7e-4 measured; the ball corner jumps 0.2). The continuity check
looks within 11 mm of the corner: the vertical round, 2.5 mm long past its
setback, meets its faces 11.2 mm out with every round's G1 jump.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 8089137776 kernel: G2 corners at concave corners, mixed ones refused
The inner corner of a notch, three concave r5 rounds, takes the set-back G2
patch as a convex corner does: one valid solid with the ball corner's 13
faces, seam jump 6.3e-4 per mm clear of the hole's corners against the
ball's 0.2. A corner of two convex rounds and a concave one is refused as not
supported: SMLib sets back only corners of one convexity.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 8fbb575a5e kernel-cases: a continuity check, and ladder 07/015 graded by it
expected.json `continuity`: over the tangent seams wholly within `within_mm`
of `near`, the curvature jump across them (exact surfaces, 65 stations a
seam) at most `curvature_jump_per_mm` clear (`clear_mm` along the seam) of the
vertices where two of them turn, where a neighbour's own G1 seam ends.

07/015, the box corner's three r5 rounds with corner: g2: one valid body of 10
faces within the box, its patch's twelve seams jumping at most 1e-3 per mm
clear of the hole's six corners by 1.2 mm (2.7e-4 measured; the ball corner
of 009 jumps 0.2). Its golden entry is the passing run's.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 d8282b3361 doc, engine: corner: g2 sets each corner back for its G2 patch
FeatureKind::Fillet with corner G2 is kernel::fillet_g2_corners, its setbacks
the corners' distances (the rest 1.5 r); setbacks now go with either corner.
The engine's corner test builds the G2 corner, default and set back 7, one
closed solid of 10 faces within 0.1% of the ball corner's volume.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 704640375d kernel: fillet_g2_corners, set-back corners filled G2 to every face round them
A corner where three or more rounded edges meet, every edge there rounded, is
set back (1.5 r unless a setback names it) and left open by SMLib
(blend_smlib::fillet_setback_open: the sheet and each corner's hole, in the
sheet's orders); each hole is filled by fill::matched_patch, the height field
over its plane fitted to the position, tangent plane and normal curvature
across the boundary of every face beside it (exact second derivatives), rounds
and planes alike, each edge's pcurve its exact projection; SMLib sews the
sheet and the patches into one solid, which must close. The history is the
sewing's carried through the sheet's, each patch face made from the rounded
edges its neighbours come from.

corner_g2 is that construction now. The polar patch over three sections it
held (never sewn in) could not be: its boundary is a closed cubic through
stations, which rounds off a corner of the loop, and the setback hole has six.

The 60 x 40 x 20 box corner of r5 rounds (07/015): 10 faces, a valid closed
solid (record and SMLib's check), curvature jump across the patch's seams
6.3e-4 per mm clear of the hole's corners against the ball's 0.2; set back 8
between the hull and prism bounds; set back 11 to 15 inside the box but by
under 7e-4; all eight corners of a box filled; refusals named.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 d63a50c47c kernel: seam diagnostics give every station's values
SeamReport.stations: each station's edge fraction, gap, normal angle and
curvature jump, alongside its point, so a seam's profile (where a jump holds,
where it fades) can be read and plotted, not only its worst value.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 6263db8d66 smlib: Brep::blend_setback_open, set-back corners left open with their holes
smlib_blend_setback_open's binding: the sheet, and per corner a Hole, its
edges in order (each starting where the one before ends), each with the face
beside it and whether that face runs it forwards. The holes' buffer starts at
64 edges a corner and grows once to the length a first call names. Tested on
the r5 box corner set back 8: 9/30/22, a sheet SMLib's check passes, one hole
of twelve edges chained end to start; an unrounded edge at the corner is
Unsupported.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 29225d2c8a geom: fill_matched, a height field G1/G2 to the faces beside its loop
fill_loop's bicubic height field over the loop's plane, fitted to the
neighbours' derivatives as well as the loop: every condition of a graph is
linear in its heights (G1: the gradient from the face's normal; G2: the second
derivative along the face's leave direction from its normal curvature), so
one banded least-squares solve with the thin-plate energy decides the surface.
Its parameters stay plane coordinates, so an edge's pcurve is still the edge
projected onto the plane, exactly.

Where a round's section meets a plane at a corner of the loop, the section has
the round's curvature and the plane is flat across its own curve: no surface
is G2 to both there. The G2 rows fade in over 15% of the run from each corner;
asked over a few cells instead, the plane's flatness to the second order along
its curve pulls the surface off the whole side. Grids go to 128 spans, which
G2 to a plane along a curved line needs. The thin-plate weight is a thousand
times fill_loop's: with the slope and curvature rows acting a little inside
the loop, the weaker one let the surface rise past a plane it is G2 to (0.06
mm at a box corner of r5 rounds set back 8).

loop_frame is fit_once's plane, shared.

Tests: the hole a setback leaves at a box corner of r5 rounds set back 8,
within 2.2e-5 of the loop, 0.027 degrees and 4.7e-4 per mm of its neighbours
clear of the corners; set back 7.5 to 15, under its planes but by under 7.2e-4;
a hole in a cylinder filled with the cylinder's own second order; refusals.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 7fde0bdffd Profiler: docs/perf.md says how to switch it on and read it
What each category records, self and total time, the table and the Chrome
trace; the CLI's --profile and --profile-out on scripts, designs and STEP
files; diagnostics.profile over the control channel.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 11:40:49 -04:00
jyvikoandClaude Opus 5.5 faffa66648 Profiler: the diagnostics.profile test holds while other tests record
The profiler is process-wide, so the engine's other tests (the schema
check's failing diagnostics.profile calls among them) record into it while
this test does. It now shows the reset by the wall time starting again,
and checks only rows that are certain to be there.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 11:40:49 -04:00
jyvikoandClaude Opus 5.5 fafd977b05 Profiler: the Profile operations preference switches recording at run time
- Graphics page: "Profile operations" (off by default) starts and stops the
  profiler when it changes; an agent's diagnostics.profile in between stands,
  and SOLIDCRAFT_PROFILE=1 is not undone by the default at start-up.
- The desktop app reads SOLIDCRAFT_PROFILE at start-up.
- Labels in en, ar, de, he, ja, ko, zh. The pending-messages test compares
  right-to-left pending text in display order, as the catalogs give it.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:40:49 -04:00
jyvikoandClaude Opus 5.5 9cd655259d Profiler: commands, feature evaluation, io; diagnostics.profile; CLI --profile
- Session::execute is a command span; Model::evaluate and each feature computed
  (by its type) are spans; io's import, export and design read/write too; the
  STEP reader's topology, pcurves and solid record.
- diagnostics.profile (contract + output schema): report, start/stop, reset,
  Chrome trace file.
- A STEP/IGES import's reply carries its own profile while recording.
- Every app compiles the profiler in by default (feature `profile`);
  SOLIDCRAFT_PROFILE=1 starts it.
- solidcraft-cli run/eval/bench-open --profile print the table on stderr,
  --profile-out writes the trace; run --profile works on designs and STEP files.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:40:49 -04:00
jyvikoandClaude Opus 5.5 319c0bc9f7 Profiler: kernel operations and STEP/IGES import stages are spans
Booleans, blends, sweeps, lofts, shell/draft/offset, healing and sewing,
SMLib conversions, meshing and measuring; the import as parse, index,
per-solid read, placement and mesh check, convert batches and finish.
The existing per-step boolean/tessellate capture names its spans too.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:40:49 -04:00
jyvikoandClaude Opus 5.5 10ea00e740 Profiler: every SMLib C API call is a span, timed by the C API itself
The C API logs each call with its steady_clock time; the log sink records
that as an smlib span (child of whatever runs on the calling thread).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:40:49 -04:00
jyvikoandClaude Opus 5.5 bc205bf860 Profiler crate: nested per-thread spans, an aggregate table and a Chrome trace
solidcraft-profile (L0, standalone): spans with self and total time, SMLib-timed
records, a bounded trace (200k events) and an aggregate that stays; compiled in
with the `enabled` feature, off at run time until switched on.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:40:49 -04:00
jyvikoandClaude Opus 5.5 541b94a608 Smooth edges: hide only joins inside one smooth surface (G2); draw tangent joins
An edge is left out of the shaded view only where its two faces meet
with one tangent plane (normals within 0.5 degrees) and one curvature
across the edge: at each station the faces' normal curvatures square to
the edge agree within 0.5 degrees' worth, |k1 - k2| <= 0.0087 x
max(|k|, 1/L), L the edge's length, so the continued faces turn apart
by no more than that over a radius of curvature or the edge's length.
Fillet boundaries (0 to 1/r), corner-patch joins and a plane tangent to
a cylinder are drawn again, straight ones included. A modelled thread's
flank pieces (one sweep) differ by at most 0.0046 and stay hidden.

Second derivatives of a spline surface now exist at a boundary point a
pcurve carries a rounding step past the knot range, as its point and
first derivatives already did.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:16:05 -04:00
jyvikoandClaude Opus 5.5 970c297452 Smooth edges: a measured crease is kept apart from a tangent display join
Smoothness (normals within 0.5 degrees) and a crease are separate
verdicts. A crease is certified where the normals differ by more than
the evaluation can account for: each pcurve point's measured distance
off the edge's own curve times the faces' larger principal curvatures.
So a real crease too small to see is not drawn in the shading but stays
a pickable edge in the wireframe, overriding a coarse same-surface seam
fit, as before; exact tangent joins (fillets, seams, a thread's flank
pieces) are no crease.

The viewport's smooth-wall test expects the wireframe to draw
`edge_visible` edges: the offset ellipse's pieces meet at real creases
of 1e-4 rad that the old checker could not certify.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:16:05 -04:00
jyvikoandClaude Opus 5.5 f6645e2c6a Threads: a modelled thread's tangent flank joins are not drawn
The M10 thread's 32 flank-piece joins meet with normals about 1.5e-6
degrees apart (measured independently with seam_diagnostics); each is
left out of the shaded view, stays pickable and stays in the wireframe.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:16:05 -04:00
jyvikoandClaude Opus 5.5 c95580d04f Smooth edges: one G1 rule on exact surfaces and pcurves
An edge is left out of the shaded view when its two faces' outward
normals, evaluated on their exact surfaces at each use's own pcurve,
agree within half a degree at eight stations along it (a seam one face
meets itself across is the same test with its two pcurves); it is a
protected crease when they differ by more. Replaces the special cases
for ruled clamped Bezier patches, planes, cylinders and cones. Fillet
tangent joins and corner-patch joins are hidden too; they stay
pickable and in the wireframe.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:16:05 -04:00
jyvikoandClaude Opus 5.5 15caa50d2a CI affected crates: no truck crates are vendored any more
The truck vendor/ crates went with the kernel's move to SMLib, so their
mapping and the test that selected the kernel for vendor/truck-shapeops
are gone; egui-wgpu is the one vendored crate left.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 11:03:55 -04:00
jyvikoandClaude Opus 5.5 b52a01e299 Attribution: the hand-written box STL of kernel case 4561
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 11:03:55 -04:00
jyvikoandClaude Opus 5.5 57d48aa9f0 Clippy: the kernel's and engine's warnings on develop
A collapsible if (assemble.rs), two manual assign operations (sew.rs), a range loop indexing
the placement inverse's translation row (step_in), and two needless borrows (engine features),
which failed CI's clippy -D warnings. No behaviour change.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:03:55 -04:00
jyvikoandClaude Opus 5.5 fddb57c0d3 Thread dialog: its labels in the catalogs; Arabic and Hebrew pending messages compare in display order
Seven labels of the thread dialog had no English catalog entry, so they stayed English in every
language (every_ui_label_literal_reaches_an_english_catalog_entry): Extent, Ends, Chamfer Angle,
Chamfer Depth, the two ISO 4753 hints and the designation hint. They are in
assets/locales/pending/thread-dialog-labels.json with Arabic, Hebrew, Japanese and Chinese, the
catalogs that must be complete. The ISO 4753 hints are looked up by id, and the designation hint
takes its example as {example}, so a right-to-left language places it where it reads.

pending_messages_are_in_the_catalogs compared a pending message with the catalog's text, which
for Arabic and Hebrew is in display order since #3768; it compares with that order now, as the
catalog stores it.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:03:55 -04:00
jyvikoandClaude Opus 5.5 6517d1ee6b Arabic and Hebrew catalogs: #4414's thread direction labels out, as in every other catalog
Main's Arabic and Hebrew catalogs (#3768) arrived with thread.direction, thread.left_hand and
thread.right_hand, the labels of #4414's screw direction, which this branch replaced with the
thread's hand and took out of every catalog.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:47:17 -04:00
jyvikoandClaude Opus 5.5 873124c49b CI: develop runs like main; SMLib is fetched after the Rust cache is restored
Each job fetched the prebuilt SMLib into target/ before Swatinem/rust-cache restored target/,
which replaced it, so every build that links SMLib stopped with "SMLib ... is not fetched"
(the Docker image of #7403). The fetch now follows the cache restore in every job.

develop (the SMLib kernel's trunk until it merges into main) gets main's push runs: CI runs on
pushes to it, a push compares against the last passing push to its own branch, and its runs save
the Rust caches the PRs into it restore.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:33:33 -04:00
jyvikoandClaude Opus 5.5 d13300b0a1 cargo fmt: the format-40 change and the rebase's export list
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:33:33 -04:00
jyvikoandClaude Opus 5.5 652d3a2cb1 ui: main's browser picks (#4774) read the placed model through session_world
Move/Copy's pick from the browser (#4774) read Session::world_state as the placed model; it now
returns why a model cannot be placed, so the browser reads it as the other panels do, through
open_meshing::session_world (no placed bodies when it cannot be placed).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:33:33 -04:00
jyvikoandClaude Opus 5.5 8aea8e5a82 Format 40: a thread's hand on tapped holes too; v0.24.0's handedness opens as hand
v0.24.0 (format 39) saved a left-hand Thread or tapped Hole as `handedness: "left"`; this
branch replaced main's handedness (#4414) with the thread's `hand`, and features don't refuse
unknown fields, so such a design opened right-handed without a word. The pending format change
thread-hand.rs renames `handedness` to `hand` on Hole and Thread features (a `right` is
dropped, anything else refused).

Tapped holes take `hand` again, right or left (never both, and only with `thread`): the Hole
feature saves it, its thread is cut and annotated that way, solid.hole takes `hand?`, the hole
dialog's tapped rows have the thread dialog's Hand choice (without Both), editing a hole keeps
it, and hole presets save it under v0.24.0's `thread_options.handedness` key, so presets saved
by v0.24.0 recall it.

Test: a format-39 design with a left-hand thread and tapped hole opens left-handed; a hole's
`hand` refuses both and needs a thread.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 826f36a794 CI and releases fetch SMLib before building
Every job that builds the kernel with SMLib runs scripts/fetch-smlib.sh after the toolchain:
the host's prebuilt archive, the matrix target's for cross builds, wasm32's for the web jobs.
RISC-V has no archive, so its check compiles the sources with g++-riscv64-linux-gnu.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HoZgkCdAVrscuw2kjQTWDs
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 4e26dc6402 The command line and the web app link SMLib by default too
As the desktop app: SMLib is the only kernel, so a build without it models nothing. The web
app links the prebuilt wasm archive, so it needs no wasi-sdk.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HoZgkCdAVrscuw2kjQTWDs
2026-10-27 02:28:53 -04:00