A square cut is the slanted plane's ordinary crossing; the cam's half turn is the quarter turn's
contact at a symmetric angle; the r15 slab stands inside the same coincidence tolerance as the r10;
the 90 degree unfold and the 40 degree flange repeat the 72 degree and 20 degree cases' formulas.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The sloped-basin chamfers and rounds at 0.5 mm rims repeat the 1 mm rim's regimes; two of the
three knife-edge chamfer tips, the r1 and box r3 curvature corners, the r1 tangent corner, the
1 mm pocket-rim and hole-rim chamfers short of the floor and the r1 together-round each repeat a kept case's regime
and grades. #854 moves to 851-chamfer-arc-top-edge-9-5, and the cases that cited a dropped one
cite the kept one or state its formula.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The ring cut frame's and the up-down join's shells build now, and so do the up-down join's and
modern-plastic's chamfers (SMLib smlib-blend-refusals). #616's lid in the corpus still fails
SMLib's loop check, the shelled box shelled again at an inner wall is unchanged, and the
oblique cut of a cylinder's fillet still fails SmSurfOfRevolution's Test #7: 3 actions of 7.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib keeps the skirt top's offset where its loops wind the other way under the opening, the
cavity's floor (the owner's ruling of 2026-10-31: build it; a lip thinner than the wall is no
break-through).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's inset now keeps only the regions that are cavity, not the one the offsets close where
they overlap (between the two faces of #545's 0.5 floor, round the up-down join's two empty
octants). The frame's core under the recess is hollowed to a sealed void, so the case says two
shells and its closed form, 21044 mm³.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's merge now intersects the offsets of an edge's faces where they could not be mated along
it (the hole's offset poking out through the half-round side's; tangency-labs/solidcore#1795):
one closed valid solid with the one face open, as the owner ruled.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib now offsets a vertex where four faces meet (two walls and two facets at the floor's
corners, four facets at the drain) to two vertices joined by a new edge (tangency-labs/smlib
branch smlib-shells). Both volumes match their closed forms. The pocket's lining, hanging from
the top's rim round the pocket, stands apart from the slab's outer walls with the cavity rising
between them to the open top: the case says two shells in the one body.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
926 (the chamfer ending on the boss's wall), the oblique cut's r0.1
round, the every-block r1 round (its seam with the cylinder is no
contact seam, after the blend_seams fix), the up-down squares' concave
chamfers and the shelled box's lip chamfer build with SMLib branch
smlib-blend-refusals (f8650b8 and later). 1207 r0.5 passes SMLib's check
on its rails now and stays listed for the next cause: its end rib on the
boss, which starts where the round and the boss are tangent.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A blend face's name holds the edge it replaced, <face>|<face>, and a side
of that edge can be a blend face whose own name holds a |. Whether a face
is a contact of the blend was read as the edge's name starting or ending
with the face's name next to a |, so the r2 round's own face F2:side read
as a contact of the r1 round F4:blend:F1:+y|F3:blend:F1:+z|F2:side. The
edge's name is now split into its two faces, a blend side read whole as
the two faces of its own edge.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The r1 round of a block's top edge, chained onto the end curve of the r2
round of its arc at a cylinder (rig fillets/every-block-cylinder-crease-
top-edge-after-arc-round-r1), ends where it runs into the cylinder. That
edge is no seam of the r1 round: the cylinder is a face of the r2 round,
not of the r1. blend_seams takes it for one today (the r2 round's name
F3:blend:F1:+z|F2:side holds a | of its own), and the rig reads it as a
contact seam at 60 degrees.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's ruling: a round or chamfer that runs past an outer edge of its face into open air
builds, tangent where it has room and cut by the face beyond where it runs out. SMLib's branch
smlib-blends-past-rims builds them by the rig's analytic answers. Off the known-failing list:
the disc's rim past its 2 mm wall (190), the hole's top rim R12 past the plate's bottom, the
chamfer past the cylinder's bottom (2893), each closing on the wall continued as itself, and
926's chamfer ending on the boss's wall, which now builds to its answer too.
The sloped basins' R4 rim rounds (1080, mitred rounds built together where one overflows) build
to their analytic volumes (to 6e-9), and stay listed with that reason: their continuity check
(g1 at every blend seam) takes in the mitres' creases, G0 by the mitre ruling.
2893-chamfer-two-distances-elliptical-rim is graded as a solid (the owner: it builds) and stays
listed, waiting on the ruling on unequal chamfers along a rim whose angle varies.
5158-fillet-round-just-past-a-10mm-face stays listed with its cause found: the round passes
5e-6 under the box's top back edge, inside the body's tolerance.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A projected spline edge of several Bezier spans came into the sketch as one
curve per span (#1508), so a G2 round's bottom edge was 16 curves and a path
naming the corner named one span of it (#3604). The kernel now reads such an
edge (a spline, or an elliptical arc of several spans) as the one clamped
B-spline it is over the edge's interval, its knots and weights its own, and
the sketch takes it as one control spline whose ends sit on the edge's
vertices. Planar regions still read edges span by span. The 3604 case builds
with its original path and leaves KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A sketch spline over control points was always the clamped uniform B-spline
over them, so a free-form edge whose knots are not evenly spaced (or whose
weights are not 1) could only come into a sketch as one curve per Bezier
span. A control spline now may save `nurbs`: its clamped knots and its
weights. Its points, polyline, exact pieces (one a knot span; conics for a
rational quadratic), the solver's distance and curvature, links, parallel
re-projection and inspect.sketch all read them; a loaded design's are
checked. One pending format file (spline-knots).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>