The nearest point on a spline (5cb015fae measured spline faces up front too) may settle on
another part of the surface, or on its boundary for a point a hair past it, and reported gaps
the edges do not have: 2.9 mm on Poppy Humanoid's leg shells, whose edges lie within 0.003 mm
of their faces, and widened tolerances past what SMLib takes (it then refused
models/vertices-off-curves.step). The up-front measure is again for faces whose nearest point
is in closed form (plane, cylinder, cone, sphere, torus); a spline face's gaps are measured
on the pcurves its kernel makes, as the record check measures them.
The corpus survey is back to 53 of 56 files; Poppy imports 238 bodies (10 solids refused,
most for SMLib's pcurves on spline faces: solidcore#1383).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
As the app's Display Quality setting, set before the design opens so every display plan is
made at it; a level that isn't one is refused with the levels. For close-up reviews of
imported faces.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Two edges leaving a vertex almost tangentially (a cusp, as a round runs out on Poppy
Humanoid's creative_commons_license) separate by about Δκ·s²/2 at distance s while a chord of
length L sags by κL²/8: halving the chords never stops them crossing. untangle returned that
face's error for the whole plan, and the body's 1834 faces were not shown. It now returns the
faces still crossing, each with why, and plan_or_fill fills each leniently straight away and
names it in the stats (the rule of #7755): the other faces are planned as usual.
Test: a face named as still tangled is filled leniently and named with that reason.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A corner ball's edge may run from its equator over the sphere's pole to a vertex just past
it (Poppy Humanoid's creative_commons_license: 1.8° past, 0.016 mm off the pole). On the
sphere's parameters the pole is a line, and the edge's pcurve would have to jump half a turn
along it: "pcurve starts 2 from the end of the use before it, on another period". Each
edge that passes through a pole of a face it bounds (a sphere's, a revolved face's on its
axis) inside its interval is now split at the nearest point to the pole (golden-section
search from 16 samples), the new vertex placed on the pole; the loop's half turn is then at
a vertex on the pole, where a loop may run along it. Each solid's notes say how many edges
were split. The geometry check takes a vertex at a pole to within the vertex's tolerance, as
the reader already does (SurfaceEval::pole_within).
Without the split the edge's jump read as a 0.024 mm gap and was covered by a tolerance:
the measured gap now only covers what the file's geometry really has.
Test: a spherical triangle (radius 0.5) with an edge over the pole to 1.8° past it reads
with its spherical-excess area and its edge split.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
A range sampled in even steps ends at a + (b − a)·1, which may round one ulp past b, where
find_span gave no span and every B-spline evaluation there failed. The import's loop area
(the reader's sampling of each pcurve, used to turn over a face whose outer loop runs
clockwise) then had no value, the face was left as written, and the record check refused
it: "outer loop runs clockwise in (u, v)" on 7 of Poppy Humanoid's solids. The same step
had refused closed-form pcurves (426924937). find_span now takes a parameter within 8 ulps of
the domain's magnitude past an end as that end; farther is outside, as before. It fixes the
pattern for every caller rather than each sampling loop.
Poppy: 232 → 242 bodies, 15 → 7 solids not imported; the kernel tests as before.
Test: Poppy's interval's last step rounds past its end and finds the end's span; 1e-9
past is still outside.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
SMLib may end an edge at a parameter of its own: a knot its vertex lies at (-1.0 where the
vertex's angle gives -0.99999998, a 2e-8 step on the edge's quarter arc, far under 1e-6 mm).
We refused any change beyond 1e-9 of the parameter, a bound with no geometric meaning:
"SMLib moved an edge's interval" on 8 of Poppy Humanoid's faces. The ends SMLib chose are now
measured on the edge's curve: within the edge's tolerance, its pcurve is mapped onto our
interval by the affine change of parameter (exact for a B-spline: its knots move), and the
record's check measures it as any pcurve; farther is SMLib trimming the edge, refused with
how far.
Poppy: 227 → 232 bodies, 17 → 15 solids not imported, no interval refusals left.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
When an edge's tolerance is raised to the gap it has, the vertices at its ends now cover it
too, as in any tolerant record (SMLib takes the vertex's zone as at least its edges'). The
edge measures sample the interval's end as t1 itself: t0 + (t1 − t0)·1 may round past it.
(This commit also measured spline faces up front by nearest point; 04de97cd9 takes that out.)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The closed-form pcurve's lift check sampled t0 + (t1 − t0)·k/n, which at k = n can round
one step past t1 (1.2985843833752289 for an end of 1.2985843833752286), where the pcurve
on [t0, t1] has no point: the closed form was refused, and on a plane, which has no
parameter box for a kernel's pcurves, the face with it ("a face on an unbounded surface
without closed-form pcurves", Poppy Humanoid's Combine1 and others). The end is now t1.
Test: Poppy's interval on a spline on a plane; without the fix, "no exact pcurve of a
B-spline on a plane".
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
Pins tangency-labs/smlib 1072d1b (release prebuilt-1072d1b857de…): an N-sided corner
patch now meets each round on the round's own exact section edge instead of its polynomial
approximation, which the stitch kept on a near tie at some corners (solidcore#1377).
SMLIB_PREBUILT rewritten by scripts/fetch-smlib.sh --pin.
The kernel's tess, display_mesh, step, corner and fillet tests fail the same 63 as with the
previous pin, none new.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Brep::validate lets a pcurve's interval differ from its edge's by PCURVE_INTERVAL (1e-9
of the magnitude: rounding room), but check_geometry then evaluated the pcurve at the
edge's own ends and samples, which may lie just past it: "the pcurve has no point at
2.0000000000082903" on four of Poppy Humanoid's solids, circle edges whose end vertex
sits on a quarter of their form, where SMLib's pcurve ends on the knot. Both of the
check's pcurve readings (the use's points and the loop's area) now take the edge
parameter on the pcurve's interval, through one reader.
Poppy: 195 → 199 bodies, 41 → 37 solids not imported; the corpus survey and the kernel
tests are as before.
Test: a pcurve whose interval ends 1e-11 short of its edge's validates and checks;
without the clamp, "the pcurve has no point at 1".
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
A closed-form pcurve (a B-spline edge's control points projected onto its plane) is
accepted within half its edge's tolerance, and the edge carried the file's: Poppy
Humanoid has planes whose B-spline edges stand 9 µm off them in a file that states
10 µm. The closed form was refused, and a plane has no parameter box for SMLib to make
pcurves in: "a face on an unbounded surface without closed-form pcurves" on 11 of its
solids. On a plane, cylinder, cone, sphere or torus (nearest points in closed form)
each edge's distance from the surface is now measured along it first, and its
tolerance covers three times that; a spline face's gaps stay measured on its kernel's
pcurves, with the 1.5 × margin of a vertex's. The pcurve code reads each use's own
tolerance.
Poppy: 194 → 195 bodies, the unbounded-surface refusals 11 → 3 (the solids they let
through now stop at later steps); the corpus survey and the kernel tests are as before.
Test: a plane face whose B-spline edges stand 0.8e-6 mm above it in a file stating
1e-6 mm imports with its closed forms; without the measure it fails as Poppy's did.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
A TOROIDAL_SURFACE whose tube reaches its axis (major radius at most the minor, or
written with a negative major radius) and a DEGENERATE_TOROIDAL_SURFACE were refused.
They are read as what they are: the tube's meridian circle (centre C + R·X, its angle
from X towards Z) revolved about the axis, the same points and normal as ISO 10303-42's
formula, a negative R putting the tube's centre across the axis.
A revolved circle or ellipse that meets its axis is now its whole arc on the face's
side, pole to pole, in closed form (where s0 + M cos(t - phi) = 0), and its NURBS form
is cut there exactly (Boehm knot insertion, bspline::segment): the parameter stays the
quarter grid's, so the edges' forms and straight pcurves are unchanged, and the surface
ends at the poles instead of running on to whole quarters past the axis (which folded
the surface over itself, and left a face with one bound around the axis without its
pole). The face's boundary picks the apple or the lemon.
On Poppy Humanoid 22 solids were refused for these tori; with the SMLib fixes before
this none of their torus faces fails: Poppy 42 -> 27 solids not imported, 194 -> 215
bodies.
Tests (hand-written files, analytic answers): a horn torus round of radius 1 on a pin
(V = 8 pi + pi(5/3 + pi/2)); a spindle torus pin end (major 1, minor 2, its apex in a
dimple at z = sqrt 3, V = 3 sqrt3 pi + 8 pi^2/3 on the cylinder) as TOROIDAL and
DEGENERATE_TOROIDAL, with a seam to the pole and with one bound; a nearly round end
(0.005 / 0.345) in two halves with SolidWorks's apex vertex; the lemon of a spindle torus
as one seam-bounded face with major radius -1 and as a degenerate torus with its lemon
selected (V = pi(6 sqrt3 - 8 pi/3)). Volumes and areas within 1e-3.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
The pcurves close a face's loop through a pole to within the face's tolerance (a
point where crossing half a period moves less than that): there the periodic parameter
is free and the loop jumps across. The reader's check that no loop crosses a seam
without a seam edge took a pole only exactly (1e-9 relative), so it refused the loops
the pcurves had closed near one. Poppy Humanoid's nearly round pin ends (a spindle
torus of major radius 0.005, minor 0.345) have their apex vertex at the tube's top,
3.6e-5 mm above the true pole: their meridians end 1.7e-6 rad short of it, and 13
faces were refused. Both now use one test, SurfaceEval::pole_within.
Test: a point 2e-7 mm from a sphere's axis is a pole within 1e-6 mm, not within 1e-7.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
A revolved circle whose centre is as far from the axis as its radius (a horn torus, its
tube touching the axis) measured its major radius a few ulps above its minor from the
profile's control points, became SMLib's ring torus, and SMLib refused it
(SM_ERR_INVALID_INPUT: no ring torus of that NURBS). A ring torus now needs its tube
clear of the axis by more than rounding (1e-9 of the radius, the slack the same test
already takes for the circle's plane); a horn torus goes as its rational B-spline.
Test: a revolved unit circle 1.5 from the axis is a ring torus; at 1, 1 + 4 ulp and 0.5
it stays a revolution (develop calls the first two ring tori).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
A face on a placed revolution that carries its NURBS form (every STEP surface of
revolution, read since b6a3b31ff) was written as two NURBS blocks: the revolution's own
net, then the form, flagged FACE_NURBS_FORM on a NURBS face. SMLib reads one block per
face, so the flat arrays did not add up and it refused the body (SM_ERR_INVALID_INPUT),
in the main import and in the one-face sheets SMLib makes pcurves on. SMLib has no class
for a revolution: the form is the face, its range and trims already in its parameters,
so it now goes as that NURBS face with no form flag. A revolution the analytic pass
recognises (a plane, cylinder, cone, sphere, ring torus) is unchanged.
Test: surface_of_revolution_sense_follows_iso, which develop fails with the refusal,
passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
Each edge is sampled on its own, and a short one within the chord tolerance is one
segment. A face bounded by two such edges (a lens of short arcs, a sliver strip of a
cylinder between two rulings) had two chords on one line: "degenerate boundary", and
the whole body's display mesh failed with it (one of Poppy Humanoid's bodies lost all
336 faces to one sliver). Such a loop's segments are now halved until it has three; the
new nodes are on the edges' curves and shared by every face that runs them.
Test: a lens of two radius-1000 arcs beside a 2 m face meshes; without the split it
fails with the same error.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
An edge's curve as a file writes it may lie off a face's surface by more than the
file's stated uncertainty: Poppy Humanoid's intersection curves lie up to 9 µm off
surfaces in a file that states 0.01 µm, and 24 of its solids were refused by the
record check ("pcurve … lifts off its edge's curve"). Each use's gap, between its
pcurve on the surface and its edge's curve, is now measured along the edge at 17
points as the record check measures it, and the edge's tolerance covers it (1.5 ×
the gap, as a vertex's covers its gap; more than 1 mm is refused). The pcurves are as
made, and each solid's notes say how many edges were raised and how far.
The pcurve fit's tenfold retries went in 6cc0401fa; this measures instead of
retrying. On the corpus (the repository's STEP/IGES files, the models repository,
Poppy): 50 → 53 of 56 files import; Poppy 132 → 194 bodies.
Test: a hand-written domed patch whose edges are written 0.2 µm above it (SMLib makes
its pcurves) imports with them covered; 1.5 mm off is refused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
New metric tapped holes drill the tap maker's drill (M8 6.8 mm). The Design preference "Metric
tapped holes drill the major diameter less the pitch" (`metric_tap_drill_major_less_pitch`, off
by default) gives them the drill every metric size took before (M8 6.75 mm): the Hole dialog
shows and sends it, and `solid.hole` given a thread and no `diameter` drills it, through the
session as `auto_project` is (kept when a design is opened or started, and across tabs). Unified,
pipe and taper sizes keep their tabulated drills; a given diameter is unchanged. Saved designs
keep the drill they stored either way.
Labels in en, ar, he, ja, zh, de and ko.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
Every tapped hole now drills the tap maker's tabulated drill. ISO metric takes Yamawa YEU23's
drill size column for cutting taps (printed p.704, M coarse; pp.704 to 706, MF fine): M8 drills
6.8 mm and M12 10.3 mm, where the major less the pitch gave 6.75 and 10.25. A custom metric size
the table lacks keeps the major less the pitch. UNC/UNF (Guhring), G, Rp, Rc and NPT (Yamawa)
were tabulated already. The Thread command's suggested hole for a metric size follows.
The Hole dialog's Tap drill diameter is now a field, the tap maker's drill by default, and the
command's `diameter` with a thread is checked the same way: a drill is accepted from the
internal thread's standard minor diameter (or the tap maker's drill where that lies below it:
Rp, Rc, NPT) to 5% over the tap maker's drill. Outside that the command names the range and
why. The field's tooltip gives the drill, the minor diameter and the range. Presets keep a
chosen drill.
A saved design keeps the diameter it stored, so it builds as before, and editing such a hole
keeps its drill: no preference and no format change. Scripts that give a thread without a
diameter drill the new default; ladder 05/007, 11/003 and rig case threads/2115 follow
analytically, and their golden entries are re-measured from runs (tier 05 re-sorted by time).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
The Rc and NPT drills were rounded to a drill series from a third-party reproduction of DIN 345
and a fractional/letter inch series cited from memory. They now come from the same tap maker's
catalogue the G and Rp drills do: Yamawa YEU23, printed p.709 (Rc, the maximum straight bored
hole with non-full threads, Rc 1/16 to 4) and p.710 (NPT, the maximum straight bored hole, 1/16
to 3). A size its tables lack (Rc 5 and 6, NPT 3 1/2 to 12) is refused as a tapped hole, naming
the range. The dialog's tooltip keeps the standard's minor diameter where the thread ends.
Rc 1/2 drills 17.6 mm (minor 17.807), 1/2 NPT 17.60 mm (minor 17.473).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
An Rc or NPT hole was drilled to the exact minor diameter where the thread ends, a size no shop
stocks. It now takes the largest stocked drill not larger than that: metric drills of the DIN 345
series for Rc (to 100 mm), letter and fractional inch drills by 64ths (to 1 1/2 in, ASME B94.11M)
for NPT; past the series it is bored to the exact value. The Hole dialog's drill shows the inch
size for NPT, and its tooltip the exact standard value. Rc 1/2: 17.807 mm, drilled 17.75 mm;
1/2 NPT: 17.473 mm, drilled 11/16 in (17.4625 mm).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
A preset's thread options save `modeled` and `ease_out` (a named ISO 3508 runout or the fade's
length, kept portable as the other lengths are) and recall them into the dialog. A runout
without a modelled thread is no preset's. Recalling checked the thread with the metric parser
only, so a UNC, G, Rp, Rc or NPT preset was refused; it checks the tapped-thread catalogue now.
An older preset without these options recalls as before: listed, square.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
Ladder 06/017's golden entry was edited by hand when the chamfered tip moved to ISO 724's d3.
Re-measured by running the case (solidcraft-cli kernel-cases on SMLib): its counts, area and
volume are the ones written by hand; its time is the run's. The tier's order by time holds.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The tapped-hole catalogue takes ISO 7-1's Rc and ASME B1.20.1's NPT internal taper threads,
every size of the tables a modelled thread cuts. Their drill is the internal minor diameter where
the thread ends (the reference plane's minor at the face less the 1 in 16 taper over the useful
or effective thread length), derived from the standards rather than a tap maker's table. An
external R is still no hole's.
A tapped hole's options mirror the thread's: `modeled` cuts its thread into the wall, from the
entry, by the same cut as `solid.thread` (now one function both call), and `ease_out` fades its
inner end out before the bottom (ISO 3508); without it the groove stops square at the thread
depth, clear of a blind hole's bottom. The Hole dialog's Tapped rows add Rc and NPT, Modeled
and the End choice (Square, Fade, Fade Length). The format notes in pending/thread-ends.rs and
pending/pipe-threads.rs record the new keys and sizes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The thread dialog offers the pipe threads: G (ISO 228-1), Rp (ISO 7-1), R and Rc (ISO 7-1) and
NPT (ASME B1.20.1). Their sizes are listed by designation without a pitch, one start and a hand
of right or left; a size picked for a hole the dialog sized Rc stays Rc.
Rp, ISO 7-1's parallel internal thread an R screws into, is a form of its own (`rp`): the
parallel profile (H = 0.960491 P) at ISO 7-1's gauge diameters, refused on a shaft. Its cut
meets the analytic material of its profile within 1e-5, as G does.
A taper thread takes a chamfered tip: each end's cone is measured from the major diameter the
taper has at that end. Pipe threads are not ISO metric, so they give chamfer_depth.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The thread's start is its free end: it runs off plain or chamfered (ISO 4753). Its inner end
stops square in its own profile or fades over a length; an empty Fade Length is ISO 3508's
runout (2.5 P, or 1.25 P for a thread saved short). A thread saved chamfered at both ends keeps
that. "Square" is its own message (thread.end_square), apart from the geometric square. The
new labels are in en, ar, he, ja, zh, de and ko; Extent, Ends, the chamfer labels and the ISO
4753 hint come from the catalog entries already on develop.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A thread's start runs off its free end, plain or chamfered; only its inner end fades out
(ease_out) or stops square. The `ease_in` field, the command parameter (refused now, naming
ease_out), the dialog's Ease In row and their docs are removed; `pending/thread-ends.rs`
drops a saved `ease_in` as the design opens. The runout test covers the short, standard and a
sub-turn fade at the inner end.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The free-end test looked for material 1 to 1.5 pitches past the face's end, beyond the first
pitch so that a chamfer the groove runs out through counts as free. A plate thinner than that
(a boss on a 1 mm plate under M10) had none there, so its top was taken for a free end and
the groove's one-pitch overrun cut into the plate (15 mm³ of a 1 mm plate).
An end is now closed when, over the overrun's whole reach, material lies outside the face's
cylinder (inside it, for a hole) at the radii the groove cuts beyond the face: a shoulder,
plate, head or blind bottom, however thin, steps out past the face, while a chamfer, neck,
countersink or counterbore steps the other way. The band test beyond the first pitch stays
for a cylinder that goes on past a split.
The regression test builds the boss as the app does (a rounded plate, a circle sketched on its
top face, extruded with Join) on 6 and 1 mm plates.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Three forms: `bspp` (G, ISO 228-1, 55° parallel), `bspt` (R external, Rc internal, ISO 7-1,
55° taper 1 in 16) and `npt` (ASME B1.20.1, 60° taper 1 in 16). Their sizes are tabulated
from the public sources: ISO 7-1:1978 Table 1 (its gauge-plane diameters are the G sizes)
and NBS Handbook H28 (1957) Table VII.2; tests check every row against the standards' own
relations.
A taper thread starts at its free end with its standard diameter there (external: the gauge
diameter its gauge length in, internal: at the face). Its groove is the screw sweep with the
section moved 1/32 of the axial travel off the axis (the radial law the runouts use, added to
it), its section reaching just past the crest, and the material beyond the major cone (or
inside the minor cone) is cut with it, as a die or tap cuts the crests. An external one runs
its standard length by default.
The volumes are checked against the profile's material fraction integrated over the tapered
radii: G 1/2 to 2e-6, R 1/2, Rc 1/2 and 1/2-14 NPT within 0.2 % of the cut.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
`tip` was none|chamfer, chamfer cutting every free end. It is now none|start|both: `start`
chamfers the end the thread starts from, refused when that end is not free (a shoulder, or a
stop inside the face), and `both` every free end as `chamfer` did. The dialog's Tip pick offers
None, Start and Both; `tip: chamfer` in a command names its replacements.
The thread's end options (runouts, tip, chamfer angle and depth) came without a format
change file; `pending/thread-ends.rs` records them and rewrites a saved `tip: chamfer` to
`both`.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ISO 4753's chamfered end bounds the end's diameter by the minor diameter. The default took the
modelled root (the basic d1) for it, so the cone's small circle lay on the root cylinder and
the chamfer ring pinched to nothing wherever the groove reached the end. The default is now
the external minor diameter d3 = d - 1.226869 P of ISO 724, below d1: the cone crosses the
root, each end is a whole disk of d3 inside a whole conical ring. ISO 4753 is for ISO metric
threads; the other forms, whose root is already their design minor, give chamfer_depth.
Ladder 06/017's analytic volume follows (1945.354522563); its golden entry re-measured.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A regression test for the groove stopping at the plate's top: the boss loses the
closed-form volume and the plate keeps all of its 9600 mm³, with and without a runout
and a chamfered tip.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Curvature continuous is the Type entry's name; Corners (Ball, Smooth patch) and Setback are
described with the command words they write. The codes (G1, G2) stay in the text, where they
explain the words.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
Patch, Boundary and Blend Surface list Position, Tangent, Curvature and Curvature change; each
order's code (G0 to G3) and what it means is in the row's hover text. The Continuity Analysis
legend, its seam markers and its status line use the same words (Crease for a G0 seam). The
segments now draw their labels translated. The new labels carry over each catalog's existing
translation with the code taken off, so no language loses its wording; a word another label
already translates keeps that translation.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
The Continuity G1|G2 control repeated Type (both set `type`) and G1 silently cleared the
corner; it is gone, and Type names the section in words: "Curvature continuous", its code (G2)
in the row's hover text. The vertex choice moves out of Advanced as Corners: Ball | Smooth
patch, shown only while the edges have a corner where three or more rounded edges meet (or the
fillet already has a smooth patch), enabled for Constant radius with Exact fit and saying why
when not. Smooth patch shows Setback: one distance for every corner, sent as `setbacks` at each
corner's vertex; left empty, the command's default (1.5 x the radius) applies. A fillet saved
with setbacks reopens with them: one distance at exactly the dialog's corners shows in Setback,
any other list is kept as saved. "Smooth" in Variable Radius is "Smooth radius change". The
stale "G2 corner construction is not supported yet" tooltip and the "Fit and G2 corners" note
are replaced by new messages (en, ar, de, he, ja, ko, zh).
No command parameter changes; saved designs open unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
A face whose boundary crosses itself in (u, v) (a cusp, a sliver whose sides
sag across each other) was an error, and the body had no display plan. It is
now planned once more with a lenient constrained Delaunay in (u, v): sides
crossing one already kept are left out, the rest is seeded and refined as any
face, and its points lie on the surface, where the GPU evaluates them. The
display has no hole, but the face is still a defect upstream, in its pcurves
or seams: PlanStats::lenient names it with the strict plan's refusal, and the
display plan logs a warning for each such face, so it is never silent.
The face boundaries keep coming from the exact pcurves (d61efb306); cdt::Fill
gets its `lenient` field back (dropped in 3f2585569). The old flat fill (#4021,
tess/fallback.rs) stays gone: develop removed it in 9138e8704. A face the
lenient fill refuses too (loops that do not close in (u, v), or wind round a
seam or pole) stays an error naming the face. Closes#4453's intent on develop.
(cherry picked from commit 84de5aa071)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
SMLib's out_failed_corner reaches Rust as Error::CornerRefused { corner }, and the
kernel names the corner by its point: a G2 fillet at a corner of mixed convexity
says where it is and that SMLib sets back only corners whose rounds are all
convex or all concave. Engine test checks the message through solid.fillet.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
The inner corner of a 20 x 20 x 10 notch in the 60 x 40 x 20 box, three
concave r5 rounds with corner: g2: one valid body of 13 faces within the box,
the patch's twelve seams jumping at most 1e-3 per mm clear of the hole's six
corners (2.7e-4 measured; the ball corner jumps 0.2). The continuity check
looks within 11 mm of the corner: the vertical round, 2.5 mm long past its
setback, meets its faces 11.2 mm out with every round's G1 jump.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The inner corner of a notch, three concave r5 rounds, takes the set-back G2
patch as a convex corner does: one valid solid with the ball corner's 13
faces, seam jump 6.3e-4 per mm clear of the hole's corners against the
ball's 0.2. A corner of two convex rounds and a concave one is refused as not
supported: SMLib sets back only corners of one convexity.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
expected.json `continuity`: over the tangent seams wholly within `within_mm`
of `near`, the curvature jump across them (exact surfaces, 65 stations a
seam) at most `curvature_jump_per_mm` clear (`clear_mm` along the seam) of the
vertices where two of them turn, where a neighbour's own G1 seam ends.
07/015, the box corner's three r5 rounds with corner: g2: one valid body of 10
faces within the box, its patch's twelve seams jumping at most 1e-3 per mm
clear of the hole's six corners by 1.2 mm (2.7e-4 measured; the ball corner
of 009 jumps 0.2). Its golden entry is the passing run's.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
FeatureKind::Fillet with corner G2 is kernel::fillet_g2_corners, its setbacks
the corners' distances (the rest 1.5 r); setbacks now go with either corner.
The engine's corner test builds the G2 corner, default and set back 7, one
closed solid of 10 faces within 0.1% of the ball corner's volume.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A corner where three or more rounded edges meet, every edge there rounded, is
set back (1.5 r unless a setback names it) and left open by SMLib
(blend_smlib::fillet_setback_open: the sheet and each corner's hole, in the
sheet's orders); each hole is filled by fill::matched_patch, the height field
over its plane fitted to the position, tangent plane and normal curvature
across the boundary of every face beside it (exact second derivatives), rounds
and planes alike, each edge's pcurve its exact projection; SMLib sews the
sheet and the patches into one solid, which must close. The history is the
sewing's carried through the sheet's, each patch face made from the rounded
edges its neighbours come from.
corner_g2 is that construction now. The polar patch over three sections it
held (never sewn in) could not be: its boundary is a closed cubic through
stations, which rounds off a corner of the loop, and the setback hole has six.
The 60 x 40 x 20 box corner of r5 rounds (07/015): 10 faces, a valid closed
solid (record and SMLib's check), curvature jump across the patch's seams
6.3e-4 per mm clear of the hole's corners against the ball's 0.2; set back 8
between the hull and prism bounds; set back 11 to 15 inside the box but by
under 7e-4; all eight corners of a box filled; refusals named.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SeamReport.stations: each station's edge fraction, gap, normal angle and
curvature jump, alongside its point, so a seam's profile (where a jump holds,
where it fades) can be read and plotted, not only its worst value.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
smlib_blend_setback_open's binding: the sheet, and per corner a Hole, its
edges in order (each starting where the one before ends), each with the face
beside it and whether that face runs it forwards. The holes' buffer starts at
64 edges a corner and grows once to the length a first call names. Tested on
the r5 box corner set back 8: 9/30/22, a sheet SMLib's check passes, one hole
of twelve edges chained end to start; an unrounded edge at the corner is
Unsupported.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fill_loop's bicubic height field over the loop's plane, fitted to the
neighbours' derivatives as well as the loop: every condition of a graph is
linear in its heights (G1: the gradient from the face's normal; G2: the second
derivative along the face's leave direction from its normal curvature), so
one banded least-squares solve with the thin-plate energy decides the surface.
Its parameters stay plane coordinates, so an edge's pcurve is still the edge
projected onto the plane, exactly.
Where a round's section meets a plane at a corner of the loop, the section has
the round's curvature and the plane is flat across its own curve: no surface
is G2 to both there. The G2 rows fade in over 15% of the run from each corner;
asked over a few cells instead, the plane's flatness to the second order along
its curve pulls the surface off the whole side. Grids go to 128 spans, which
G2 to a plane along a curved line needs. The thin-plate weight is a thousand
times fill_loop's: with the slope and curvature rows acting a little inside
the loop, the weaker one let the surface rise past a plane it is G2 to (0.06
mm at a box corner of r5 rounds set back 8).
loop_frame is fit_once's plane, shared.
Tests: the hole a setback leaves at a box corner of r5 rounds set back 8,
within 2.2e-5 of the loop, 0.027 degrees and 4.7e-4 per mm of its neighbours
clear of the corners; set back 7.5 to 15, under its planes but by under 7.2e-4;
a hole in a cylinder filled with the cylinder's own second order; refusals.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
What each category records, self and total time, the table and the Chrome
trace; the CLI's --profile and --profile-out on scripts, designs and STEP
files; diagnostics.profile over the control channel.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
The profiler is process-wide, so the engine's other tests (the schema
check's failing diagnostics.profile calls among them) record into it while
this test does. It now shows the reset by the wall time starting again,
and checks only rows that are certain to be there.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
- Graphics page: "Profile operations" (off by default) starts and stops the
profiler when it changes; an agent's diagnostics.profile in between stands,
and SOLIDCRAFT_PROFILE=1 is not undone by the default at start-up.
- The desktop app reads SOLIDCRAFT_PROFILE at start-up.
- Labels in en, ar, de, he, ja, ko, zh. The pending-messages test compares
right-to-left pending text in display order, as the catalogs give it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>