The sloped-basin chamfers and rounds at 0.5 mm rims repeat the 1 mm rim's regimes; two of the three knife-edge chamfer tips, the r1 and box r3 curvature corners, the r1 tangent corner, the 1 mm pocket-rim and hole-rim chamfers short of the floor and the r1 together-round each repeat a kept case's regime and grades. #854 moves to 851-chamfer-arc-top-edge-9-5, and the cases that cited a dropped one cite the kept one or state its formula. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
15 lines
2.4 KiB
Plaintext
15 lines
2.4 KiB
Plaintext
# The fillet cases that fail today, one a line: `<case> <why it fails today>`. Sorted. The fillet
|
|
# rig gate (.github/workflows/fillet-rig.yml) fails on a case that fails and is not listed here,
|
|
# and on a listed case that passes: a fix removes its line in the same pull request.
|
|
# Baseline: develop 242bbc89f with the SMLib fixes of 2026-10-29 (integration-overnight + b78bd4a), aarch64 Linux.
|
|
1080-fillet-equal-slope-basin-1-mm-rim-loop-4 builds to the analytic volume (rel 5e-9), but the continuity check (g1 at every blend seam) takes in the mitre's creases, G0 by the mitre ruling: the case's continuity seams need the owner's word
|
|
1080-fillet-sloped-basin-1-mm-rim-r4-2-edges builds to the analytic volume (rel 6e-9), but the continuity check (g1 at every blend seam) takes in the mitre's creases, G0 by the mitre ruling: the case's continuity seams need the owner's word
|
|
1080-fillet-sloped-basin-1-mm-rim-r4-4-edges builds to the analytic volume (rel 3e-9), but the continuity check (g1 at every blend seam) takes in the mitre's creases, G0 by the mitre ruling: the case's continuity seams need the owner's word
|
|
1207-fillet-bar-top-edge-after-boss-arc-round-r0-5 SMLib's check refuses the round: internal coincident control points in its end rib on the boss, which starts where the round and the boss are tangent (the boss's intersection marched there in spans down to 6e-8 mm)
|
|
2893-chamfer-distance-and-angle-past-the-wall-refused refused for another reason: SMLib SM_ERR_INVALID_INPUT, not a check saying the angle runs past the wall
|
|
2893-chamfer-two-distances-elliptical-rim SMLib status 1001: the two arcs of the rim take their chamfer offsets each at its own midpoint, where the faces' angle differs (78.5 and 101.5 deg), and their chamfers do not meet at the tangent corners (held for the owner's ruling on unequal chamfers of a varying angle)
|
|
4782-fillet-bar-edge-wider-than-both-faces SMLib status 1001: a convex round past both its faces is not yet built by subtraction
|
|
5158-fillet-round-just-past-a-10mm-face SMLib status 1001: the round passes 5e-6 under the box's top back edge, inside the body's tolerance (1e-5), and subtracting its removal region maps that edge to two of the region's faces (SmTopologyIntersector); 10.0001-10.04 open
|
|
9-fillet-corner-curvature-with-reduce-fit not supported yet: solid.fillet builds corner g2 with the exact fit only
|
|
9-fillet-corner-curvature-with-taper-fit not supported yet: solid.fillet builds corner g2 with the exact fit only
|