Ladder 06/009 had no way to ask for one: "solid.thread has no runout (vanishing thread) length". With SMLib's smlib_screw_sweep_radial (replay e7acea1): - smlib: the FFI binding and Brep::screw_sweep_radial, the profile moved off the axis by a piecewise linear law of the turn; crate test: a tooth moved out 1 mm over three turns has A 2π (c turns + ∫ offset dt). - kernel: sweep_helix_radial, sharing sweep_helix's checks (helix_profile). - doc: `ease_in`, `ease_out` (a length, or ISO 3508's standard 2.5 P or short 1.25 P) fade the groove over that length, its section moving out of the material as it turns (outward for a shaft, inward for a nut). ease_in is at the end the thread starts from. The runout lies past the full-form length: beyond a square stop, before a shoulder up to its clearance; at a free end inside the face. Runouts longer than the thread are refused. No end gets one by default, so saved threads keep their geometry. The cut is the integral over the turn of the clipped section's 2π∫ r dA: engine test (2.5 P and 1.25 P between two collars) within the sweep's wall tolerance times the runouts' wall area (0.029 against a 0.036 mm³ bound), ladder 06/009 (004's shaft, a 2 P runout before the shoulder) graded in closed form (measured 1.7e-6 off). Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
24 lines
1.3 KiB
JSON
24 lines
1.3 KiB
JSON
{
|
|
"sources": [],
|
|
"what": "004's M10 thread run from the free top end, vanishing over a 3 mm (2 P) runout before the d16 shoulder",
|
|
"source": "analytic",
|
|
"method": "the shaft's lower end is a shoulder (the d16 collar lies past it, in the groove's way), so the groove (its runout included) stops with its widest part clear of it: its centre w = (P/4 + 2 (d/2 + 0.05P - r_root) tan30)/2 = 0.699551 mm above the shoulder (its half width at the tool's outer edge, 0.05 P past the crest), and the square stop inside material removes exactly as if the groove ended at its centre (see 003); the top end is free, the groove runs out into the air. The runout (ease_out, at the end away from `from`) moves the groove's section out of the shaft as it turns, linearly from h = d/2 - root + 0.05P at s = 10 + w to 0 at s + 3: the cut per radian is f(o) = int r w(r - o) dr from root + o to 5 (w the section's width at its own radius), the runout removes 2 pi (3/P) mean(f) (Simpson, exact on the cubic), the full-depth groove from s + 3 to the free top end 2 pi f(0) (35 - s - 3)/P (the overrun past the free end as in 001). V = pi 8^2 10 + pi 5^2 25 - both. Tolerance 0.01%: SMLib's exact radial screw sweep",
|
|
"body_count": 1,
|
|
"volume_mm3": 3673.442500807,
|
|
"bbox": {
|
|
"min": [
|
|
-8,
|
|
-8,
|
|
0
|
|
],
|
|
"max": [
|
|
8,
|
|
8,
|
|
35
|
|
]
|
|
},
|
|
"tolerance": {
|
|
"rel": 0.0001
|
|
}
|
|
}
|