* claim: #6211 Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> * Joints: a loop whose axes are a hair out of parallel still moves (#6211) Holes picked on parts are rarely exactly in line. A closed loop through axes a few hundredths of a microradian apart (a lever, link and a rod on a cylindrical axle) can't close exactly: it closes to nanometres, and the gap grows as it turns. The loop solver wanted 1e-7 mm, so it threw such a closure away (the loop stayed open, its parts at 0 dof) or stopped a drive or drag after a fraction of a degree. The conflict check is now 1e-4 mm / 1e-6 rad (it was below what its message can show), and joint.drive / motion and joint.reach close the loop at each step as at the start: to the tight tolerance where they get there, otherwise within the conflict check. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> --------- Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2473 lines
111 KiB
Rust
2473 lines
111 KiB
Rust
//! Joints between occurrences: joint origins (snap frames on component geometry, re-found on
|
||
//! every solve so they follow edits), joints (rigid, revolute, slider, cylindrical, pin-slot,
|
||
//! planar, ball, and relations that tie only part of a placement, `joints_relations.rs`) with
|
||
//! their motion values and limits, motion links (gears, racks and screws are
|
||
//! links whose ratio comes from radii or a pitch; a cam's follower follows a table worked out from
|
||
//! its profile, `joints_cam.rs`), and the solver that places occurrences from the joint graph.
|
||
//!
|
||
//! A joint makes B's joint frame coincide with A's frame moved by the joint's motion:
|
||
//! `T_B · F_b = T_A · F_a · M(q) · Flip · Tail(q)`, so `T_B = T_A · F_a · M(q) · Flip · Tail(q) · F_b⁻¹`
|
||
//! (`Tail` is a relation's tilt and turns after the mate; the identity for the others), where `T`
|
||
//! are occurrence world transforms, `F` the joint frames in each component's own frame, and `q`
|
||
//! the joint's values (angles in radians, distances in mm). The solver walks the graph from
|
||
//! grounded occurrences (and the root, which never moves). Joints that close a loop (a four-bar
|
||
//! linkage, a slider-crank) are met by moving the values of the other joints around the loop;
|
||
//! those that still disagree are reported.
|
||
|
||
use std::collections::{BTreeMap, BTreeSet, VecDeque};
|
||
|
||
use serde::{Deserialize, Serialize};
|
||
use solidcraft_geom::{Aabb3, Vec3};
|
||
|
||
use solidcraft_sketch::linalg;
|
||
|
||
use crate::{DocError, Document, IDENTITY, Mat, ModelState, Result, apply_point, apply_vector, mat_inverse, mat_mul};
|
||
|
||
/// Joints the solver (and the URDF export) reads at most.
|
||
pub const MAX_JOINTS: usize = 10_000;
|
||
|
||
/// Where a joint origin sits on a component's geometry (component coordinates).
|
||
#[derive(Clone, Debug, PartialEq, Serialize, Deserialize)]
|
||
#[serde(tag = "type", rename_all = "snake_case")]
|
||
pub enum Snap {
|
||
/// An explicit frame (origin, z axis, x axis).
|
||
Frame {
|
||
origin: Vec3,
|
||
z: Vec3,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
x: Option<Vec3>,
|
||
},
|
||
/// The centre of the planar face nearest `pick`, z along its outward normal. `face` is the
|
||
/// face's persistent name: when it names a planar face, that face's own plane and centre are
|
||
/// taken (the pick only tells the pieces of a split face apart).
|
||
FaceCenter {
|
||
pick: Vec3,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
face: Option<String>,
|
||
/// What turns the frame about z (default: any direction square to z).
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
x: Option<XRef>,
|
||
},
|
||
/// The centre of a circular end of the cylindrical face at `pick`, z along its axis
|
||
/// (pointing out of the face's end). `face` is the face's persistent name: when it names a
|
||
/// cylindrical face, that face's own axis, radius and extent are taken. `end` is the name of
|
||
/// the face across the rim at the chosen end (the plate's face a hole opens onto), so the
|
||
/// end stays the same when the design changes; without it (or when neither end has that
|
||
/// face any more), the end nearer `pick` along the axis.
|
||
CircleCenter {
|
||
pick: Vec3,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
face: Option<String>,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
end: Option<String>,
|
||
/// What turns the frame about z (default: any direction square to z).
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
x: Option<XRef>,
|
||
},
|
||
/// A point on an edge of a planar face: the edge's middle, or the corner where it meets the
|
||
/// edge `corner` names (`joints_edge.rs`). `edge` and `face` are the persistent names of the
|
||
/// edge and the face (found first); `pick` is a point on the edge as it was picked.
|
||
Edge {
|
||
pick: Vec3,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
edge: Option<String>,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
face: Option<String>,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
corner: Option<String>,
|
||
/// The frame's z when it isn't the face's normal (an edge or a corner picked as it is,
|
||
/// not on a face): the point still follows the edge, found by name.
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
axis: Option<EdgeAxis>,
|
||
},
|
||
/// A point, z along `z` (default +Z) and x toward `x` laid square to z (default: one chosen
|
||
/// from z alone).
|
||
Point {
|
||
point: Vec3,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
z: Option<Vec3>,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
x: Option<Vec3>,
|
||
},
|
||
}
|
||
|
||
/// The z of an edge origin that isn't its face's normal (component coordinates); its x follows
|
||
/// from z alone, as a point origin's does.
|
||
#[derive(Clone, Copy, Debug, PartialEq, Serialize, Deserialize)]
|
||
#[serde(rename_all = "snake_case")]
|
||
pub enum EdgeAxis {
|
||
/// Along a straight edge, the way this points: a hinge on the edge turns about it as it moves.
|
||
Along(Vec3),
|
||
/// This direction.
|
||
Fixed(Vec3),
|
||
}
|
||
|
||
impl EdgeAxis {
|
||
pub fn dir(self) -> Vec3 {
|
||
match self {
|
||
EdgeAxis::Along(d) | EdgeAxis::Fixed(d) => d,
|
||
}
|
||
}
|
||
}
|
||
|
||
/// What sets a joint origin's x axis (its turn about z): a direction, or a face found by its
|
||
/// persistent name, so a round origin keeps its turn when the design changes.
|
||
#[derive(Clone, Debug, PartialEq, Serialize, Deserialize)]
|
||
#[serde(untagged)]
|
||
pub enum XRef {
|
||
/// A direction (component coordinates); its part square to z is taken.
|
||
Dir(Vec3),
|
||
/// A face: a plane's outward normal, a cylinder's way from the origin to its axis (another
|
||
/// hole), any other face's way from the origin to the point of it nearest `pick` (component
|
||
/// coordinates; it also tells the pieces of a split face apart, default the origin).
|
||
Face {
|
||
face: String,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
pick: Option<Vec3>,
|
||
},
|
||
}
|
||
|
||
impl Snap {
|
||
/// The persistent face and edge names the snap refers to (its face, its end's, its x reference's;
|
||
/// an edge origin's edge, face and corner edge).
|
||
pub fn face_names(&self) -> Vec<&String> {
|
||
let mut out = Vec::new();
|
||
if let Snap::FaceCenter { face, x, .. } | Snap::CircleCenter { face, x, .. } = self {
|
||
out.extend(face.iter());
|
||
if let Some(XRef::Face { face, .. }) = x {
|
||
out.push(face);
|
||
}
|
||
}
|
||
if let Snap::CircleCenter { end: Some(end), .. } = self {
|
||
out.push(end);
|
||
}
|
||
if let Snap::Edge { edge, face, corner, .. } = self {
|
||
out.extend(edge.iter().chain(face.iter()).chain(corner.iter()));
|
||
}
|
||
out
|
||
}
|
||
|
||
/// [`Snap::face_names`], to rewrite them (a copied component's faces have new names).
|
||
pub fn face_names_mut(&mut self) -> Vec<&mut String> {
|
||
let mut out = Vec::new();
|
||
match self {
|
||
Snap::FaceCenter { face, x, .. } => {
|
||
out.extend(face.iter_mut());
|
||
if let Some(XRef::Face { face, .. }) = x {
|
||
out.push(face);
|
||
}
|
||
}
|
||
Snap::CircleCenter { face, end, x, .. } => {
|
||
out.extend(face.iter_mut());
|
||
out.extend(end.iter_mut());
|
||
if let Some(XRef::Face { face, .. }) = x {
|
||
out.push(face);
|
||
}
|
||
}
|
||
Snap::Edge { edge, face, corner, .. } => out.extend(edge.iter_mut().chain(face.iter_mut()).chain(corner.iter_mut())),
|
||
_ => {}
|
||
}
|
||
out
|
||
}
|
||
|
||
/// The direction a face or circle snap keeps as its frame's x (`XRef::Dir`), in the
|
||
/// component's coordinates; `None` for a face reference or none.
|
||
pub fn frame_x(&self) -> Option<Vec3> {
|
||
match self {
|
||
Snap::FaceCenter { x: Some(XRef::Dir(d)), .. } | Snap::CircleCenter { x: Some(XRef::Dir(d)), .. } => Some(*d),
|
||
_ => None,
|
||
}
|
||
}
|
||
|
||
/// A face or circle snap given no x reference keeps `x` (the frame's x as it is now): each
|
||
/// solve lays it onto the face, or square to the hole's axis, as the geometry is then, so a
|
||
/// part on a face that tilts keeps its turn about z. Without it (designs made before) x
|
||
/// follows from z alone, and turns through a right angle where z crosses 0.9 along the
|
||
/// component's X. A snap with a reference keeps it.
|
||
pub fn with_frame_x(mut self, x: Vec3) -> Snap {
|
||
if let Snap::FaceCenter { x: slot @ None, .. } | Snap::CircleCenter { x: slot @ None, .. } = &mut self {
|
||
*slot = Some(XRef::Dir(x));
|
||
}
|
||
self
|
||
}
|
||
|
||
/// Whether every point and direction in the snap is finite.
|
||
pub fn is_finite(&self) -> bool {
|
||
let x_ok = |x: &Option<XRef>| match x {
|
||
Some(XRef::Dir(d)) => d.is_finite(),
|
||
Some(XRef::Face { pick, .. }) => pick.is_none_or(|p| p.is_finite()),
|
||
None => true,
|
||
};
|
||
match self {
|
||
Snap::Frame { origin, z, x } => origin.is_finite() && z.is_finite() && x.is_none_or(|x| x.is_finite()),
|
||
Snap::FaceCenter { pick, x, .. } | Snap::CircleCenter { pick, x, .. } => pick.is_finite() && x_ok(x),
|
||
Snap::Point { point, z, x } => point.is_finite() && z.is_none_or(|z| z.is_finite()) && x.is_none_or(|x| x.is_finite()),
|
||
Snap::Edge { pick, axis, .. } => pick.is_finite() && axis.is_none_or(|a| a.dir().is_finite()),
|
||
}
|
||
}
|
||
}
|
||
|
||
/// A joint origin: a snap on an occurrence's component (occurrence 0 = the root design).
|
||
#[derive(Clone, Debug, PartialEq, Serialize, Deserialize)]
|
||
pub struct JointOrigin {
|
||
pub occurrence: u64,
|
||
pub snap: Snap,
|
||
}
|
||
|
||
/// A named joint origin (Joint Origin command), referenced by joints by name.
|
||
#[derive(Clone, Debug, PartialEq, Serialize, Deserialize)]
|
||
pub struct NamedOrigin {
|
||
pub name: String,
|
||
pub origin: JointOrigin,
|
||
}
|
||
|
||
#[derive(Clone, Copy, Debug, PartialEq, Eq, Serialize, Deserialize)]
|
||
#[serde(rename_all = "snake_case")]
|
||
pub enum JointKind {
|
||
Rigid,
|
||
Revolute,
|
||
Slider,
|
||
Cylindrical,
|
||
PinSlot,
|
||
Planar,
|
||
Ball,
|
||
/// B's z stays parallel to A's (against it unless flipped); B moves and turns about z freely.
|
||
Parallel,
|
||
/// B's z stays square to A's; B moves freely and turns about either z.
|
||
Perpendicular,
|
||
/// B's z stays at the joint's `angle` from mated (about their common x); B moves freely and
|
||
/// turns about either z.
|
||
Angle,
|
||
/// B's origin stays on A's xy plane (`offset` off it); B slides on it and turns any way.
|
||
PointOnPlane,
|
||
/// B's origin stays on A's z axis; B slides along it and turns any way.
|
||
PointOnLine,
|
||
/// B's z axis lies in A's xy plane (`offset` off it: a cylinder's radius makes it tangent);
|
||
/// B slides on the plane, turns about A's z and about its own axis.
|
||
LineOnPlane,
|
||
}
|
||
|
||
impl JointKind {
|
||
pub fn parse(s: &str) -> Option<JointKind> {
|
||
Some(match s.to_ascii_lowercase().replace([' ', '_', '-'], "").as_str() {
|
||
"rigid" => JointKind::Rigid,
|
||
"revolute" | "rotate" => JointKind::Revolute,
|
||
"slider" | "slide" => JointKind::Slider,
|
||
"cylindrical" => JointKind::Cylindrical,
|
||
"pinslot" => JointKind::PinSlot,
|
||
"planar" => JointKind::Planar,
|
||
"ball" => JointKind::Ball,
|
||
"parallel" => JointKind::Parallel,
|
||
"perpendicular" | "square" => JointKind::Perpendicular,
|
||
"angle" => JointKind::Angle,
|
||
"pointonplane" | "pointonface" => JointKind::PointOnPlane,
|
||
"pointonline" | "pointonaxis" => JointKind::PointOnLine,
|
||
"lineonplane" | "lineonface" => JointKind::LineOnPlane,
|
||
_ => return None,
|
||
})
|
||
}
|
||
/// Names of the joint's values, in order (angles in radians, distances in mm).
|
||
pub fn dofs(self) -> &'static [&'static str] {
|
||
match self {
|
||
JointKind::Rigid => &[],
|
||
JointKind::Revolute => &["angle"],
|
||
JointKind::Slider => &["distance"],
|
||
JointKind::Cylindrical => &["angle", "distance"],
|
||
JointKind::PinSlot => &["angle", "slide"],
|
||
JointKind::Planar => &["x", "y", "angle"],
|
||
JointKind::Ball => &["yaw", "pitch", "roll"],
|
||
JointKind::Parallel => &["x", "y", "z", "angle"],
|
||
JointKind::Perpendicular | JointKind::Angle => &["x", "y", "z", "turn", "spin"],
|
||
JointKind::PointOnPlane => &["x", "y", "yaw", "pitch", "roll"],
|
||
JointKind::PointOnLine => &["slide", "yaw", "pitch", "roll"],
|
||
JointKind::LineOnPlane => &["x", "y", "turn", "spin"],
|
||
}
|
||
}
|
||
pub fn is_angle(self, i: usize) -> bool {
|
||
matches!(self.dofs().get(i), Some(&("angle" | "yaw" | "pitch" | "roll" | "turn" | "spin")))
|
||
}
|
||
/// A relation that only ties some directions or points (parallel, on a plane…): made where
|
||
/// the parts are, its values start as the nearest that meet it, so B moves no more than it
|
||
/// must.
|
||
pub fn is_relation(self) -> bool {
|
||
matches!(
|
||
self,
|
||
JointKind::Parallel
|
||
| JointKind::Perpendicular
|
||
| JointKind::Angle
|
||
| JointKind::PointOnPlane
|
||
| JointKind::PointOnLine
|
||
| JointKind::LineOnPlane
|
||
)
|
||
}
|
||
}
|
||
|
||
/// A joint between two occurrences.
|
||
#[derive(Clone, Debug, PartialEq, Serialize, Deserialize)]
|
||
pub struct Joint {
|
||
pub id: u64,
|
||
pub name: String,
|
||
pub kind: JointKind,
|
||
pub a: JointOrigin,
|
||
pub b: JointOrigin,
|
||
/// Current values of the joint's degrees of freedom.
|
||
#[serde(default)]
|
||
pub values: Vec<f64>,
|
||
/// Per value: (min, max) limits.
|
||
#[serde(default)]
|
||
pub limits: Vec<Option<(f64, f64)>>,
|
||
/// Don't mate: B's z along A's instead of against it (by default the origins mate, as two
|
||
/// faces meeting).
|
||
#[serde(default, skip_serializing_if = "std::ops::Not::not")]
|
||
pub flip: bool,
|
||
/// Distance from A's frame to B's along z, and a turn about it (radians).
|
||
#[serde(default)]
|
||
pub offset: f64,
|
||
#[serde(default)]
|
||
pub angle: f64,
|
||
#[serde(default, skip_serializing_if = "std::ops::Not::not")]
|
||
pub suppressed: bool,
|
||
/// The expressions the offset, the angle and the values were typed as: they are worked out
|
||
/// again whenever the design changes, so a joint follows the parameters it is defined by.
|
||
#[serde(default, skip_serializing_if = "JointExprs::is_empty")]
|
||
pub exprs: JointExprs,
|
||
}
|
||
|
||
/// Expressions a joint's numbers follow (over the design's parameters): the offset (a length),
|
||
/// the angle and each value (angles or lengths as the joint's values are). A number typed in
|
||
/// place of one drops it.
|
||
#[derive(Clone, Debug, Default, PartialEq, Serialize, Deserialize)]
|
||
pub struct JointExprs {
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
pub offset: Option<String>,
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
pub angle: Option<String>,
|
||
/// By value index, as in `Joint::values`.
|
||
#[serde(default, skip_serializing_if = "Vec::is_empty")]
|
||
pub values: Vec<Option<String>>,
|
||
}
|
||
|
||
impl JointExprs {
|
||
pub fn is_empty(&self) -> bool {
|
||
self.offset.is_none() && self.angle.is_none() && self.values.iter().all(Option::is_none)
|
||
}
|
||
|
||
/// The expression value `i` follows.
|
||
pub fn value(&self, i: usize) -> Option<&str> {
|
||
self.values.get(i).and_then(Option::as_deref)
|
||
}
|
||
|
||
/// Value `i` follows `e` (or nothing).
|
||
pub fn set_value(&mut self, i: usize, e: Option<String>) {
|
||
if e.is_some() && self.values.len() <= i {
|
||
self.values.resize(i + 1, None);
|
||
}
|
||
if let Some(slot) = self.values.get_mut(i) {
|
||
*slot = e;
|
||
}
|
||
while self.values.last().is_some_and(Option::is_none) {
|
||
self.values.pop();
|
||
}
|
||
}
|
||
}
|
||
|
||
/// Largest offset or value an expression may give a joint (mm, or radians for an angle).
|
||
const MAX_EXPR_VALUE: f64 = 1e9;
|
||
|
||
/// A design's parameter values, worked out the first time an expression names one and kept for
|
||
/// the next: a pass over the joints works out every joint's expressions again, and each would
|
||
/// otherwise evaluate every parameter of the design anew.
|
||
pub struct Params<'a> {
|
||
doc: &'a Document,
|
||
vals: std::cell::OnceCell<BTreeMap<String, crate::expr::Value>>,
|
||
}
|
||
|
||
impl<'a> Params<'a> {
|
||
pub fn new(doc: &'a Document) -> Params<'a> {
|
||
Params { doc, vals: std::cell::OnceCell::new() }
|
||
}
|
||
|
||
/// What [`Document::eval`] gives for `e`.
|
||
pub fn eval(&self, e: &str, kind: crate::expr::Kind) -> Result<f64> {
|
||
crate::expr::eval_with(e, &|n| {
|
||
self.vals.get_or_init(|| self.doc.param_values().0).get(n).copied().ok_or_else(|| DocError::Expr(format!("unknown parameter `{n}`")))
|
||
})?
|
||
.to_kind(kind)
|
||
}
|
||
}
|
||
|
||
/// A joint's offset, angle and values worked out from its expressions (those without one keep
|
||
/// their numbers), or why one can't be: an unknown name, a wrong unit, or a number too large.
|
||
pub fn expressed(params: &Params, j: &Joint) -> Result<(f64, f64, Vec<f64>)> {
|
||
let eval = |e: &str, kind: crate::expr::Kind, what: &str| -> Result<f64> {
|
||
let v = params.eval(e, kind).map_err(|err| DocError::Invalid(format!("joint {}: {what} `{e}`: {err}", j.name)))?;
|
||
if v.is_finite() && v.abs() < MAX_EXPR_VALUE { Ok(v) } else { Err(DocError::Invalid(format!("joint {}: {what} `{e}` gives {v}", j.name))) }
|
||
};
|
||
let x = &j.exprs;
|
||
let offset = match &x.offset {
|
||
Some(e) => eval(e, crate::expr::Kind::Length, "offset")?,
|
||
None => j.offset,
|
||
};
|
||
let angle = match &x.angle {
|
||
Some(e) => eval(e, crate::expr::Kind::Angle, "angle")?,
|
||
None => j.angle,
|
||
};
|
||
let mut values = j.values.clone();
|
||
for (i, e) in x.values.iter().enumerate().take(j.kind.dofs().len()) {
|
||
let Some(e) = e else { continue };
|
||
let kind = if j.kind.is_angle(i) { crate::expr::Kind::Angle } else { crate::expr::Kind::Length };
|
||
let name = j.kind.dofs().get(i).copied().unwrap_or("value");
|
||
let v = eval(e, kind, name)?;
|
||
if values.len() <= i {
|
||
values.resize(i + 1, 0.0);
|
||
}
|
||
if let Some(slot) = values.get_mut(i) {
|
||
*slot = v;
|
||
}
|
||
}
|
||
Ok((offset, angle, values))
|
||
}
|
||
|
||
/// Values the loop solver leaves alone: those a motion link sets and those an expression does.
|
||
fn set_values(asm: &Assembly) -> BTreeSet<(u64, usize)> {
|
||
let mut set: BTreeSet<(u64, usize)> = asm.links.iter().map(|l| (l.b, l.ib)).collect();
|
||
for j in &asm.joints {
|
||
set.extend(j.exprs.values.iter().enumerate().filter(|(_, e)| e.is_some()).map(|(i, _)| (j.id, i)));
|
||
}
|
||
set
|
||
}
|
||
|
||
/// Value of joint `b` (index `ib`) = ratio · value of joint `a` (index `ia`) + offset, or for a
|
||
/// cam, its `lift` table at a's value + offset.
|
||
#[derive(Clone, Debug, PartialEq, Serialize, Deserialize)]
|
||
pub struct MotionLink {
|
||
pub a: u64,
|
||
#[serde(default)]
|
||
pub ia: usize,
|
||
pub b: u64,
|
||
#[serde(default)]
|
||
pub ib: usize,
|
||
pub ratio: f64,
|
||
#[serde(default)]
|
||
pub offset: f64,
|
||
/// Gears, a rack and pinion, a screw or a cam: what the ratio (or a cam's table) comes from.
|
||
/// It is worked out from it again whenever the design changes (`coupling_values`), so it
|
||
/// follows the radii, the pitch and the cam's profile; the last one worked out is kept in
|
||
/// `ratio` and `lift`.
|
||
#[serde(default, skip_serializing_if = "Option::is_none")]
|
||
pub coupling: Option<Coupling>,
|
||
/// A cam's follower values over one turn of a (`cam::CAM_SAMPLES` of them, in b's units, the
|
||
/// offset left out); empty for every other link.
|
||
#[serde(default, skip_serializing_if = "Vec::is_empty")]
|
||
pub lift: Vec<f64>,
|
||
}
|
||
|
||
impl MotionLink {
|
||
/// b's value for a's value `x` (before b's limits). A cam's table that is not whole (a
|
||
/// hand-edited file) gives no value, so b keeps where it is; a table on any other link is
|
||
/// not read.
|
||
pub fn follow(&self, x: f64) -> f64 {
|
||
match &self.coupling {
|
||
Some(Coupling::Cam(_)) if self.lift.len() == cam::CAM_SAMPLES => cam::lift_at(&self.lift, x) + self.offset,
|
||
Some(Coupling::Cam(_)) => f64::NAN,
|
||
_ => self.ratio * x + self.offset,
|
||
}
|
||
}
|
||
}
|
||
|
||
/// A length a coupling's ratio comes from: millimetres, an expression over the design's
|
||
/// parameters, or the radius of the round face picked on an occurrence (a circle-centre snap,
|
||
/// found again on every solve like a joint origin).
|
||
#[derive(Clone, Debug, PartialEq, Serialize, Deserialize)]
|
||
#[serde(untagged)]
|
||
pub enum Size {
|
||
Length(f64),
|
||
Expr(String),
|
||
Circle(JointOrigin),
|
||
}
|
||
|
||
/// The geometry a motion link's ratio comes from. `reverse` turns the follower the other way.
|
||
#[derive(Clone, Debug, PartialEq, Serialize, Deserialize)]
|
||
#[serde(tag = "type", rename_all = "snake_case")]
|
||
pub enum Coupling {
|
||
/// Two gears on revolute joints, `ra` on a's and `rb` on b's (pitch radii, or any two lengths
|
||
/// in their proportion such as tooth counts): b turns ra/rb as far as a, the other way round,
|
||
/// or the same way when one is an internal (ring) gear.
|
||
Gear {
|
||
ra: Size,
|
||
rb: Size,
|
||
#[serde(default, skip_serializing_if = "std::ops::Not::not")]
|
||
internal: bool,
|
||
#[serde(default, skip_serializing_if = "std::ops::Not::not")]
|
||
reverse: bool,
|
||
},
|
||
/// A pinion of pitch radius `radius` on a revolute joint and a rack on a slider: the rack
|
||
/// travels the radius times the pinion's turn in radians (either joint may drive).
|
||
RackPinion {
|
||
radius: Size,
|
||
#[serde(default, skip_serializing_if = "std::ops::Not::not")]
|
||
reverse: bool,
|
||
},
|
||
/// A screw: the travel advances `pitch` per turn (a cylindrical joint's angle and distance,
|
||
/// or a revolute joint and a slider). Right-handed unless reversed.
|
||
Screw {
|
||
pitch: Size,
|
||
#[serde(default, skip_serializing_if = "std::ops::Not::not")]
|
||
reverse: bool,
|
||
},
|
||
/// A cam on a revolute joint (a) and its follower (b, a slider or a revolute): b rides the
|
||
/// cam's profile (`joints_cam.rs`).
|
||
Cam(cam::Cam),
|
||
}
|
||
|
||
impl Coupling {
|
||
/// The lengths the ratio comes from: a's gear and b's, the pinion's radius, the pitch, or a
|
||
/// cam's roller radius.
|
||
pub fn sizes(&self) -> Vec<&Size> {
|
||
match self {
|
||
Coupling::Gear { ra, rb, .. } => vec![ra, rb],
|
||
Coupling::RackPinion { radius: s, .. } | Coupling::Screw { pitch: s, .. } => vec![s],
|
||
Coupling::Cam(c) => match &c.follower {
|
||
cam::Follower::Roller { radius } => vec![radius],
|
||
_ => Vec::new(),
|
||
},
|
||
}
|
||
}
|
||
|
||
pub fn sizes_mut(&mut self) -> Vec<&mut Size> {
|
||
match self {
|
||
Coupling::Gear { ra, rb, .. } => vec![ra, rb],
|
||
Coupling::RackPinion { radius: s, .. } | Coupling::Screw { pitch: s, .. } => vec![s],
|
||
Coupling::Cam(c) => match &mut c.follower {
|
||
cam::Follower::Roller { radius } => vec![radius],
|
||
_ => Vec::new(),
|
||
},
|
||
}
|
||
}
|
||
}
|
||
|
||
/// Largest length a coupling takes (mm).
|
||
const MAX_SIZE: f64 = 1e7;
|
||
|
||
/// A coupling length in millimetres: positive and finite.
|
||
fn size_of(doc: &Document, st: &ModelState, s: &Size) -> Result<f64> {
|
||
let v = match s {
|
||
Size::Length(v) => *v,
|
||
Size::Expr(e) => doc.eval(e, crate::expr::Kind::Length)?,
|
||
Size::Circle(o) => circle_at(doc, st, o)?.radius,
|
||
};
|
||
if v.is_finite() && v > 1e-9 && v <= MAX_SIZE {
|
||
Ok(v)
|
||
} else {
|
||
Err(DocError::Invalid(format!("a gear, rack, screw or roller needs a positive length, not {v}")))
|
||
}
|
||
}
|
||
|
||
/// The ratio a link's coupling gives it (b's value per a's, in radians and mm) and a cam's table
|
||
/// (`MotionLink::lift`; empty for the others), worked out from the geometry and parameters it is
|
||
/// defined by; `None` for a plain link.
|
||
pub fn coupling_values(doc: &Document, st: &ModelState, l: &MotionLink) -> Option<Result<(f64, Vec<f64>)>> {
|
||
l.coupling.as_ref().map(|c| match c {
|
||
Coupling::Cam(c) => cam::table(doc, st, l, c).map(|t| (1.0, t)),
|
||
c => coupled(doc, st, l, c).map(|r| (r, Vec::new())),
|
||
})
|
||
}
|
||
|
||
fn coupled(doc: &Document, st: &ModelState, l: &MotionLink, c: &Coupling) -> Result<f64> {
|
||
let angle = |id: u64, i: usize| doc.assembly.joints.iter().find(|j| j.id == id).is_some_and(|j| j.kind.is_angle(i));
|
||
let (turn_a, turn_b) = (angle(l.a, l.ia), angle(l.b, l.ib));
|
||
// Travel per radian, for a turn coupled to a travel either way round.
|
||
let travel = |k: f64| match (turn_a, turn_b) {
|
||
(true, false) => Ok(k),
|
||
(false, true) => Ok(1.0 / k),
|
||
_ => Err(DocError::Invalid("a rack or a screw couples a turn and a travel".into())),
|
||
};
|
||
let sign = |reverse: bool| if reverse { -1.0 } else { 1.0 };
|
||
match c {
|
||
Coupling::Gear { ra, rb, internal, reverse } => {
|
||
if !(turn_a && turn_b) {
|
||
return Err(DocError::Invalid("gears couple two turns".into()));
|
||
}
|
||
Ok(size_of(doc, st, ra)? / size_of(doc, st, rb)? * sign(!internal) * sign(*reverse))
|
||
}
|
||
Coupling::RackPinion { radius, reverse } => Ok(travel(size_of(doc, st, radius)?)? * sign(*reverse)),
|
||
Coupling::Screw { pitch, reverse } => Ok(travel(size_of(doc, st, pitch)? / std::f64::consts::TAU)? * sign(*reverse)),
|
||
// A cam's follower follows its table (`coupling_values`), not a ratio.
|
||
Coupling::Cam(_) => Ok(1.0),
|
||
}
|
||
}
|
||
|
||
/// Joints, joint origins and motion links of a design.
|
||
#[derive(Clone, Debug, Default, PartialEq, Serialize, Deserialize)]
|
||
pub struct Assembly {
|
||
#[serde(default, skip_serializing_if = "Vec::is_empty")]
|
||
pub joints: Vec<Joint>,
|
||
#[serde(default, skip_serializing_if = "Vec::is_empty")]
|
||
pub origins: Vec<NamedOrigin>,
|
||
#[serde(default, skip_serializing_if = "Vec::is_empty")]
|
||
pub links: Vec<MotionLink>,
|
||
#[serde(default, skip_serializing_if = "Vec::is_empty")]
|
||
pub contact_sets: Vec<crate::motion::ContactSet>,
|
||
/// Contact sets take effect.
|
||
#[serde(default, skip_serializing_if = "std::ops::Not::not")]
|
||
pub contact_enabled: bool,
|
||
/// Every occurrence is in contact with every other (Enable All Contact).
|
||
#[serde(default, skip_serializing_if = "std::ops::Not::not")]
|
||
pub contact_all: bool,
|
||
#[serde(default, skip_serializing_if = "Vec::is_empty")]
|
||
pub studies: Vec<crate::motion::MotionStudy>,
|
||
#[serde(default, skip_serializing_if = "Vec::is_empty")]
|
||
pub traces: Vec<crate::motion::MotionTrace>,
|
||
#[serde(default, skip_serializing_if = "Vec::is_empty")]
|
||
pub exploded: Vec<crate::motion::ExplodedView>,
|
||
}
|
||
|
||
impl Assembly {
|
||
/// Every expression the joints and motion links keep, with the joint (or the driven joint of
|
||
/// a link) and what it sets: `offset`, `angle`, a value's name, or a coupling's length.
|
||
pub fn exprs(&self) -> Vec<(u64, String, &str)> {
|
||
let mut out = Vec::new();
|
||
for j in &self.joints {
|
||
let x = &j.exprs;
|
||
out.extend(x.offset.as_deref().map(|e| (j.id, "offset".to_string(), e)));
|
||
out.extend(x.angle.as_deref().map(|e| (j.id, "angle".to_string(), e)));
|
||
for (i, e) in x.values.iter().enumerate() {
|
||
if let Some(e) = e {
|
||
out.push((j.id, j.kind.dofs().get(i).copied().unwrap_or("value").to_string(), e.as_str()));
|
||
}
|
||
}
|
||
}
|
||
for l in &self.links {
|
||
for s in l.coupling.as_ref().map(Coupling::sizes).unwrap_or_default() {
|
||
if let Size::Expr(e) = s {
|
||
out.push((l.b, "coupling".to_string(), e.as_str()));
|
||
}
|
||
}
|
||
}
|
||
for trace in &self.traces {
|
||
if let crate::motion::TraceMotion::Joint { joint, from, to, .. } = &trace.motion {
|
||
for (label, value) in [("from", from), ("to", to)] {
|
||
if let serde_json::Value::String(e) = value {
|
||
out.push((*joint, format!("trace {} {label}", trace.sketch), e.as_str()));
|
||
}
|
||
}
|
||
}
|
||
}
|
||
out
|
||
}
|
||
|
||
/// The expressions of `exprs`, to rewrite (a renamed parameter).
|
||
pub fn exprs_mut(&mut self) -> Vec<&mut String> {
|
||
let mut out = Vec::new();
|
||
for j in &mut self.joints {
|
||
let x = &mut j.exprs;
|
||
out.extend(x.offset.as_mut());
|
||
out.extend(x.angle.as_mut());
|
||
out.extend(x.values.iter_mut().flatten());
|
||
}
|
||
for l in &mut self.links {
|
||
for s in l.coupling.as_mut().map(Coupling::sizes_mut).unwrap_or_default() {
|
||
if let Size::Expr(e) = s {
|
||
out.push(e);
|
||
}
|
||
}
|
||
}
|
||
for trace in &mut self.traces {
|
||
if let crate::motion::TraceMotion::Joint { from, to, .. } = &mut trace.motion {
|
||
for value in [from, to] {
|
||
if let serde_json::Value::String(e) = value {
|
||
out.push(e);
|
||
}
|
||
}
|
||
}
|
||
}
|
||
out
|
||
}
|
||
|
||
pub fn is_empty(&self) -> bool {
|
||
self.joints.is_empty()
|
||
&& self.origins.is_empty()
|
||
&& self.links.is_empty()
|
||
&& self.contact_sets.is_empty()
|
||
&& !self.contact_enabled
|
||
&& !self.contact_all
|
||
&& self.studies.is_empty()
|
||
&& self.traces.is_empty()
|
||
&& self.exploded.is_empty()
|
||
}
|
||
}
|
||
|
||
/// A frame: origin and orthonormal axes, as a transform (local → parent).
|
||
fn frame(o: Vec3, z: Vec3, x: Option<Vec3>) -> Option<Mat> {
|
||
let z = z.normalized()?;
|
||
let x = x.and_then(|x| (x - z * x.dot(z)).normalized()).unwrap_or_else(|| z.any_perp());
|
||
let y = z.cross(x).normalized()?;
|
||
Some([[x.x, x.y, x.z, 0.0], [y.x, y.y, y.z, 0.0], [z.x, z.y, z.z, 0.0], [o.x, o.y, o.z, 1.0]])
|
||
}
|
||
|
||
fn rot_z(a: f64) -> Mat {
|
||
let (s, c) = a.sin_cos();
|
||
[[c, s, 0.0, 0.0], [-s, c, 0.0, 0.0], [0.0, 0.0, 1.0, 0.0], [0.0, 0.0, 0.0, 1.0]]
|
||
}
|
||
fn rot_x(a: f64) -> Mat {
|
||
let (s, c) = a.sin_cos();
|
||
[[1.0, 0.0, 0.0, 0.0], [0.0, c, s, 0.0], [0.0, -s, c, 0.0], [0.0, 0.0, 0.0, 1.0]]
|
||
}
|
||
fn rot_y(a: f64) -> Mat {
|
||
let (s, c) = a.sin_cos();
|
||
[[c, 0.0, -s, 0.0], [0.0, 1.0, 0.0, 0.0], [s, 0.0, c, 0.0], [0.0, 0.0, 0.0, 1.0]]
|
||
}
|
||
fn shift(x: f64, y: f64, z: f64) -> Mat {
|
||
let mut m = IDENTITY;
|
||
m[3] = [x, y, z, 1.0];
|
||
m
|
||
}
|
||
|
||
/// The joint's motion in A's frame for its values.
|
||
pub fn motion(kind: JointKind, q: &[f64]) -> Mat {
|
||
let v = |i: usize| q.get(i).copied().unwrap_or(0.0);
|
||
match kind {
|
||
JointKind::Rigid => IDENTITY,
|
||
JointKind::Revolute => rot_z(v(0)),
|
||
JointKind::Slider => shift(0.0, 0.0, v(0)),
|
||
JointKind::Cylindrical => mat_mul(&rot_z(v(0)), &shift(0.0, 0.0, v(1))),
|
||
JointKind::PinSlot => mat_mul(&shift(v(1), 0.0, 0.0), &rot_z(v(0))),
|
||
JointKind::Planar => mat_mul(&shift(v(0), v(1), 0.0), &rot_z(v(2))),
|
||
JointKind::Ball => mat_mul(&mat_mul(&rot_z(v(0)), &rot_y(v(1))), &rot_z(v(2))),
|
||
JointKind::Parallel => mat_mul(&shift(v(0), v(1), v(2)), &rot_z(v(3))),
|
||
JointKind::Perpendicular | JointKind::Angle => mat_mul(&shift(v(0), v(1), v(2)), &rot_z(v(3))),
|
||
// Their turn is about B's origin, after the offset (`tail`).
|
||
JointKind::PointOnPlane => shift(v(0), v(1), 0.0),
|
||
JointKind::PointOnLine => shift(0.0, 0.0, v(0)),
|
||
JointKind::LineOnPlane => mat_mul(&shift(v(0), v(1), 0.0), &rot_z(v(2))),
|
||
}
|
||
}
|
||
|
||
fn turn_zyx(yaw: f64, pitch: f64, roll: f64) -> Mat {
|
||
mat_mul(&mat_mul(&rot_z(yaw), &rot_y(pitch)), &rot_x(roll))
|
||
}
|
||
|
||
/// What follows the mate (`flip_of`) in a joint's link: for a relation that tilts B's z, the tilt
|
||
/// and B's turn about its own z (`spin`); for a point relation, B's turn about its origin (yaw,
|
||
/// pitch and roll about z, y and x: free of gimbal lock at the start, all 0); nothing for the
|
||
/// other joints.
|
||
fn tail(j: &Joint, q: &[f64]) -> Mat {
|
||
let v = |i: usize| q.get(i).copied().unwrap_or(0.0);
|
||
match j.kind {
|
||
JointKind::Perpendicular => mat_mul(&rot_x(std::f64::consts::FRAC_PI_2), &rot_z(v(4))),
|
||
JointKind::Angle => mat_mul(&rot_x(j.angle), &rot_z(v(4))),
|
||
JointKind::LineOnPlane => mat_mul(&rot_y(std::f64::consts::FRAC_PI_2), &rot_z(v(3))),
|
||
JointKind::PointOnPlane => turn_zyx(v(2), v(3), v(4)),
|
||
JointKind::PointOnLine => turn_zyx(v(1), v(2), v(3)),
|
||
_ => IDENTITY,
|
||
}
|
||
}
|
||
|
||
/// B's joint frame in A's for the joint's values: `M(q) · Flip · tail`.
|
||
fn link_of(j: &Joint, q: &[f64]) -> Mat {
|
||
mat_mul(&mat_mul(&motion(j.kind, q), &flip_of(j)), &tail(j, q))
|
||
}
|
||
|
||
/// Bodies of a component in the model (its own frame).
|
||
fn component_bodies<'a>(doc: &Document, st: &'a ModelState, component: u64) -> Vec<&'a crate::ModelBody> {
|
||
st.bodies.iter().filter(|b| doc.model_body_component(b) == component).collect()
|
||
}
|
||
|
||
/// The component an occurrence places (0 for the root).
|
||
fn component_of(doc: &Document, occ: u64) -> Result<u64> {
|
||
if occ == 0 {
|
||
return Ok(0);
|
||
}
|
||
doc.occurrences.iter().find(|o| o.id == occ).map(|o| o.component).ok_or_else(|| DocError::Unknown(format!("occurrence {occ}")))
|
||
}
|
||
|
||
/// A snap's pick point moved onto its named face of `component` (an error when the face is gone:
|
||
/// a joint must not quietly attach elsewhere).
|
||
fn named_pick(doc: &Document, st: &ModelState, component: u64, pick: Vec3, face: Option<&str>) -> Result<Vec3> {
|
||
match face {
|
||
Some(n) => face::named_face(doc, st, component, pick, n).map(|f| f.point),
|
||
None => Ok(pick),
|
||
}
|
||
}
|
||
|
||
/// The centre (the middle of its outline, `face::outline_centre`) and outward normal of the
|
||
/// planar face nearest `pick` (component coordinates; a body moved in from another component
|
||
/// placed by its offset, as a named face is).
|
||
fn nearest_plane(doc: &Document, st: &ModelState, o: &JointOrigin, pick: Vec3) -> Result<(Vec3, Vec3)> {
|
||
let comp = component_of(doc, o.occurrence)?;
|
||
let mut best: Option<(f64, &crate::ModelBody, solidcraft_kernel::FaceInfo, Vec3)> = None;
|
||
for b in component_bodies(doc, st, comp) {
|
||
let offset = doc.model_body_offset(b);
|
||
for f in b.joint_faces()?.iter() {
|
||
let Some(own) = f.plane_normal else { continue };
|
||
let (c, n) = match offset {
|
||
Some(m) => (apply_point(m, f.centroid), apply_vector(m, own)),
|
||
None => (f.centroid, own),
|
||
};
|
||
let d = (pick - c).dot(n).abs() + 1e-3 * (pick - c).len();
|
||
if best.as_ref().is_none_or(|(bd, ..)| d < *bd) {
|
||
best = Some((d, b, f.clone(), own));
|
||
}
|
||
}
|
||
}
|
||
let (_, b, f, n) = best.ok_or_else(|| DocError::Invalid("joint origin: no planar face there".into()))?;
|
||
// The face's middle: its outline's on a face with holes.
|
||
let c = face::outline_centre(&b.mesh(), f.index, f.centroid, n).unwrap_or(f.centroid);
|
||
Ok(match doc.model_body_offset(b) {
|
||
Some(m) => (apply_point(m, c), apply_vector(m, n)),
|
||
None => (c, n),
|
||
})
|
||
}
|
||
|
||
/// Resolve a joint origin to a frame in its component's coordinates.
|
||
pub fn resolve_origin(doc: &Document, st: &ModelState, o: &JointOrigin) -> Result<Mat> {
|
||
let bad = || DocError::Invalid("joint origin: degenerate frame".into());
|
||
match &o.snap {
|
||
Snap::Frame { origin, z, x } => frame(*origin, *z, *x).ok_or_else(bad),
|
||
Snap::Point { point, z, x } => frame(*point, z.unwrap_or(Vec3::Z), *x).ok_or_else(bad),
|
||
Snap::FaceCenter { pick, face, x } => {
|
||
// A named planar face gives its own centre and normal; another face (or none) the
|
||
// planar face nearest the point.
|
||
let comp = component_of(doc, o.occurrence)?;
|
||
let named = match face.as_deref() {
|
||
Some(n) => Some(face::named_face(doc, st, comp, *pick, n)?),
|
||
None => None,
|
||
};
|
||
let (c, n) = match named.as_ref().map(face::NamedFace::plane).transpose()?.flatten() {
|
||
Some(cn) => cn,
|
||
None => nearest_plane(doc, st, o, named.as_ref().map_or(*pick, |f| f.point))?,
|
||
};
|
||
frame(c, n, face::x_axis(doc, st, comp, x.as_ref(), c)?).ok_or_else(bad)
|
||
}
|
||
Snap::Edge { .. } => edge::edge_frame(doc, st, component_of(doc, o.occurrence)?, &o.snap),
|
||
Snap::CircleCenter { x, .. } => {
|
||
let r = round_of(doc, st, o)?;
|
||
frame(r.centre, r.z, face::x_axis(doc, st, component_of(doc, o.occurrence)?, x.as_ref(), r.centre)?).ok_or_else(bad)
|
||
}
|
||
}
|
||
}
|
||
|
||
/// A circle-centre snap's cylinder and the end it takes (component coordinates): through its
|
||
/// named face when it names a cylinder, else the cylindrical face at its pick and the end nearer
|
||
/// it, as older builds found them. Any other snap is refused.
|
||
fn round_of(doc: &Document, st: &ModelState, o: &JointOrigin) -> Result<face::Round> {
|
||
let Snap::CircleCenter { pick, face, end, .. } = &o.snap else { return Err(DocError::Invalid("pick a round face".into())) };
|
||
let comp = component_of(doc, o.occurrence)?;
|
||
if let Some(n) = face.as_deref()
|
||
&& let Some(r) = face::named_round(doc, st, comp, *pick, n, end.as_deref())?
|
||
{
|
||
return Ok(r);
|
||
}
|
||
let pick = named_pick(doc, st, comp, *pick, face.as_deref())?;
|
||
// A body moved in from another component: looked at in its own coordinates, its cylinder
|
||
// placed by its offset (as a named face is).
|
||
let cyl = component_bodies(doc, st, comp)
|
||
.into_iter()
|
||
.filter_map(|b| match doc.model_body_offset(b) {
|
||
Some(m) => solidcraft_kernel::cylinder_face_at(&b.body, apply_point(&mat_inverse(m)?, pick)).map(|c| face::placed(m, c)),
|
||
None => solidcraft_kernel::cylinder_face_at(&b.body, pick),
|
||
})
|
||
.min_by(|a, b| {
|
||
let off = |c: &solidcraft_kernel::CylinderFace| {
|
||
let v = pick - c.axis_point;
|
||
((v - c.axis * v.dot(c.axis)).len() - c.radius).abs()
|
||
};
|
||
off(a).total_cmp(&off(b))
|
||
})
|
||
.ok_or_else(|| DocError::Invalid("joint origin: no cylindrical face there".into()))?;
|
||
let s = (pick - cyl.axis_point).dot(cyl.axis);
|
||
let (at, dir) = if (s - cyl.start).abs() <= (cyl.end - s).abs() { (cyl.start, -1.0) } else { (cyl.end, 1.0) };
|
||
Ok(face::Round { cylinder: cyl, centre: cyl.axis_point + cyl.axis * at, z: cyl.axis * dir })
|
||
}
|
||
|
||
/// The cylindrical face of a circle-centre snap (component coordinates).
|
||
fn circle_at(doc: &Document, st: &ModelState, o: &JointOrigin) -> Result<solidcraft_kernel::CylinderFace> {
|
||
round_of(doc, st, o).map(|r| r.cylinder)
|
||
}
|
||
|
||
/// World transform of an occurrence (through its parents).
|
||
pub fn occurrence_world(doc: &Document, occ: u64) -> Mat {
|
||
let mut m = IDENTITY;
|
||
let mut cur = doc.occurrences.iter().find(|o| o.id == occ);
|
||
for _ in 0..1000 {
|
||
let Some(o) = cur else { break };
|
||
m = mat_mul(&o.transform, &m);
|
||
if o.parent == 0 {
|
||
break;
|
||
}
|
||
cur = doc.occurrence_of(o.parent);
|
||
}
|
||
m
|
||
}
|
||
|
||
/// Clamp values to the joint's limits.
|
||
pub fn clamp(j: &Joint, q: &mut [f64]) {
|
||
for (i, v) in q.iter_mut().enumerate() {
|
||
if let Some(Some((lo, hi))) = j.limits.get(i) {
|
||
*v = v.clamp(lo.min(*hi), hi.max(*lo));
|
||
}
|
||
}
|
||
}
|
||
|
||
/// Work requested after placing occurrences and checking their joint constraints.
|
||
#[derive(Clone, Copy, Debug, PartialEq, Eq)]
|
||
pub enum Analysis {
|
||
/// Placement, loop closure, conflicts and errors only; `Solution::dof` is empty.
|
||
Placement,
|
||
/// Also count each occurrence's remaining motion, including nearby singular poses.
|
||
DegreesOfFreedom,
|
||
}
|
||
|
||
/// The result of placing occurrences by their joints.
|
||
#[derive(Clone, Debug, Default, Serialize)]
|
||
pub struct Solution {
|
||
/// New world transforms of occurrences the joints place.
|
||
#[serde(skip)]
|
||
pub world: BTreeMap<u64, Mat>,
|
||
/// New values of the joints that moved to close loops (joint id → values).
|
||
#[serde(skip)]
|
||
pub values: BTreeMap<u64, Vec<f64>>,
|
||
/// Joints that disagree with the placement found through others: (joint id, name, why).
|
||
pub conflicts: Vec<(u64, String, String)>,
|
||
/// Joints that could not be applied (bad origin…): (joint id, name, why).
|
||
pub errors: Vec<(u64, String, String)>,
|
||
/// Remaining degrees of freedom per occurrence (6 = free, 0 = fixed): how many independent
|
||
/// values still move it, from the fixed occurrences, with loops kept closed and a value a
|
||
/// motion link sets moving with the values its link chain starts from (a driven gear has its
|
||
/// driving gear's one, a screw's travel its turn's). Empty for [`Analysis::Placement`].
|
||
pub dof: BTreeMap<u64, usize>,
|
||
/// Occurrences fixed in place (grounded, or the root's).
|
||
pub fixed: Vec<u64>,
|
||
}
|
||
|
||
/// Joint values by joint id.
|
||
type Values = BTreeMap<u64, Vec<f64>>;
|
||
|
||
/// How far two placements differ: (translation mm, rotation rad).
|
||
fn mismatch(a: &Mat, b: &Mat) -> (f64, f64) {
|
||
let t = Vec3::new(a[3][0] - b[3][0], a[3][1] - b[3][1], a[3][2] - b[3][2]).len();
|
||
// The turn between them from both its cosine and its sine: the cosine alone loses small
|
||
// angles to rounding.
|
||
let c = |i: usize, k: usize| (0..3).map(|n| a[i][n] * b[k][n]).sum::<f64>();
|
||
let sin2 = Vec3::new(c(1, 2) - c(2, 1), c(2, 0) - c(0, 2), c(0, 1) - c(1, 0)).len();
|
||
(t, sin2.atan2(c(0, 0) + c(1, 1) + c(2, 2) - 1.0))
|
||
}
|
||
|
||
/// Passes over the motion links at most: a chain of up to this many links carries its value
|
||
/// through, whatever order its links are stored in.
|
||
const MAX_LINK_PASSES: usize = 64;
|
||
|
||
/// Motion links, pass after pass until nothing changes (a chain stored from its end takes a pass
|
||
/// per link), each linked value within its joint's limits as it is set. The result is the same
|
||
/// whatever the values were before and however the links are stored, so applying them again
|
||
/// changes nothing (links that form a cycle stop after `MAX_LINK_PASSES`).
|
||
fn apply_links(asm: &Assembly, vals: &mut Values) {
|
||
let limits: BTreeMap<(u64, usize), (f64, f64)> = asm
|
||
.links
|
||
.iter()
|
||
.filter_map(|l| {
|
||
let (lo, hi) = asm.joints.iter().find(|j| j.id == l.b)?.limits.get(l.ib).copied().flatten()?;
|
||
Some(((l.b, l.ib), (lo.min(hi), hi.max(lo))))
|
||
})
|
||
.collect();
|
||
// The linked values, to see whether a pass changed any (several links writing one value
|
||
// change it within a pass, but settle from one pass to the next).
|
||
let linked = |vals: &Values| -> Vec<Option<f64>> { asm.links.iter().map(|l| vals.get(&l.b).and_then(|q| q.get(l.ib)).copied()).collect() };
|
||
for _ in 0..MAX_LINK_PASSES {
|
||
let before = linked(vals);
|
||
for l in &asm.links {
|
||
let Some(src) = vals.get(&l.a).and_then(|q| q.get(l.ia)).copied() else { continue };
|
||
let mut next = l.follow(src);
|
||
// A hand-edited table (or source) that gives no number leaves b where it is.
|
||
if !next.is_finite() {
|
||
continue;
|
||
}
|
||
if let Some((lo, hi)) = limits.get(&(l.b, l.ib)) {
|
||
next = next.max(*lo).min(*hi);
|
||
}
|
||
if let Some(v) = vals.get_mut(&l.b).and_then(|q| q.get_mut(l.ib)) {
|
||
*v = next;
|
||
}
|
||
}
|
||
if linked(vals) == before {
|
||
break;
|
||
}
|
||
}
|
||
}
|
||
|
||
/// Effective values of every joint after motion links and limits.
|
||
pub fn joint_values(asm: &Assembly) -> BTreeMap<u64, Vec<f64>> {
|
||
let mut vals: Values = asm
|
||
.joints
|
||
.iter()
|
||
.map(|j| {
|
||
let mut q = j.values.clone();
|
||
q.resize(j.kind.dofs().len(), 0.0);
|
||
(j.id, q)
|
||
})
|
||
.collect();
|
||
apply_links(asm, &mut vals);
|
||
for j in &asm.joints {
|
||
if let Some(q) = vals.get_mut(&j.id) {
|
||
clamp(j, q);
|
||
}
|
||
}
|
||
vals
|
||
}
|
||
|
||
/// The turn and offset from A's joint frame to B's: mated (B's z against A's, as faces meet)
|
||
/// unless flipped.
|
||
fn flip_of(j: &Joint) -> Mat {
|
||
// An angle relation's `angle` is its tilt (`tail`); a perpendicular one has none.
|
||
let turn = if matches!(j.kind, JointKind::Angle | JointKind::Perpendicular) { 0.0 } else { j.angle };
|
||
let mut m = rot_z(turn);
|
||
m[3][2] = j.offset;
|
||
if !j.flip { mat_mul(&m, &[[1.0, 0.0, 0.0, 0.0], [0.0, -1.0, 0.0, 0.0], [0.0, 0.0, -1.0, 0.0], [0.0, 0.0, 0.0, 1.0]]) } else { m }
|
||
}
|
||
|
||
/// Component-space frames stay fixed throughout one solve. Cache their inverses without
|
||
/// regrouping products: reversed joints still invert the value-dependent link as before.
|
||
struct JointFrames {
|
||
a: Mat,
|
||
b: Mat,
|
||
inverse_a: Option<Mat>,
|
||
inverse_b: Option<Mat>,
|
||
}
|
||
|
||
impl JointFrames {
|
||
fn new(a: Mat, b: Mat) -> Self {
|
||
Self { a, b, inverse_a: mat_inverse(&a), inverse_b: mat_inverse(&b) }
|
||
}
|
||
|
||
fn through(&self, joint: &Joint, values: &[f64], from_a: bool, t: &Mat) -> Option<Mat> {
|
||
let link = mat_mul(&link_of(joint, values), self.inverse_b.as_ref()?);
|
||
if from_a { Some(mat_mul(&mat_mul(t, &self.a), &link)) } else { Some(mat_mul(&mat_mul(t, &mat_inverse(&link)?), self.inverse_a.as_ref()?)) }
|
||
}
|
||
}
|
||
|
||
/// B's world transform from A's (or A's from B's, going the other way) for the joint's values.
|
||
fn through(j: &Joint, (fa, fb): &(Mat, Mat), q: &[f64], from_a: bool, t: &Mat) -> Option<Mat> {
|
||
JointFrames::new(*fa, *fb).through(j, q, from_a, t)
|
||
}
|
||
|
||
/// The spanning tree the solver places occurrences along, out from the fixed ones.
|
||
struct Tree<'a> {
|
||
joints: BTreeMap<u64, &'a Joint>,
|
||
/// Joint frames in component coordinates (A's, B's).
|
||
frames: BTreeMap<u64, JointFrames>,
|
||
fixed: BTreeMap<u64, Mat>,
|
||
/// Placed occurrence → (the occurrence it is placed from, the joint, from the joint's A side).
|
||
parent: BTreeMap<u64, (u64, u64, bool)>,
|
||
/// Placed occurrences in placement order.
|
||
order: Vec<u64>,
|
||
}
|
||
|
||
impl Tree<'_> {
|
||
fn step(&self, joint: u64, from_a: bool, t: &Mat, vals: &Values) -> Option<Mat> {
|
||
#[cfg(test)]
|
||
tests::PLACEMENT_STEPS.with(|steps| steps.set(steps.get() + 1));
|
||
let q = vals.get(&joint).map(Vec::as_slice).unwrap_or(&[]);
|
||
self.frames.get(&joint)?.through(self.joints.get(&joint)?, q, from_a, t)
|
||
}
|
||
|
||
/// Where every placed occurrence is for these values.
|
||
fn place(&self, vals: &Values) -> BTreeMap<u64, Mat> {
|
||
let mut placed = self.fixed.clone();
|
||
for occ in &self.order {
|
||
let Some(&(from, joint, from_a)) = self.parent.get(occ) else { continue };
|
||
if let Some(m) = placed.get(&from).and_then(|t| self.step(joint, from_a, t, vals)) {
|
||
placed.insert(*occ, m);
|
||
}
|
||
}
|
||
placed
|
||
}
|
||
|
||
/// The fixed occurrence an occurrence is placed from, and the tree joints from it up to that one.
|
||
fn path(&self, mut occ: u64) -> (u64, Vec<(u64, bool)>) {
|
||
let mut up = Vec::new();
|
||
while let Some(&(from, joint, from_a)) = self.parent.get(&occ) {
|
||
if up.len() > self.order.len() {
|
||
break;
|
||
}
|
||
up.push((joint, from_a));
|
||
occ = from;
|
||
}
|
||
(occ, up)
|
||
}
|
||
|
||
/// One occurrence's world placement for these values.
|
||
fn world(&self, occ: u64, vals: &Values) -> Option<Mat> {
|
||
let (root, up) = self.path(occ);
|
||
let mut t = *self.fixed.get(&root)?;
|
||
for (joint, from_a) in up.iter().rev() {
|
||
t = self.step(*joint, *from_a, &t, vals)?;
|
||
}
|
||
Some(t)
|
||
}
|
||
}
|
||
|
||
/// Storage shared by one residual callback's evaluations, scoped to its immutable tree.
|
||
/// Keep map nodes and path capacity, but invalidate every placement before reading new values.
|
||
struct PlacementWorkspace<'tree, 'doc> {
|
||
tree: &'tree Tree<'doc>,
|
||
placed: BTreeMap<u64, Option<Mat>>,
|
||
path: Vec<(u64, u64, bool)>,
|
||
}
|
||
|
||
impl<'tree, 'doc> PlacementWorkspace<'tree, 'doc> {
|
||
fn new(tree: &'tree Tree<'doc>) -> Self {
|
||
Self { tree, placed: BTreeMap::new(), path: Vec::new() }
|
||
}
|
||
|
||
fn at<'values>(&'values mut self, values: &'values Values) -> Placements<'values, 'tree, 'doc> {
|
||
for placed in self.placed.values_mut() {
|
||
*placed = None;
|
||
}
|
||
Placements { workspace: self, values }
|
||
}
|
||
}
|
||
|
||
/// Only this guard can read placements. Its values stay immutable until it is dropped;
|
||
/// obtaining the next guard clears validity while retaining the allocated storage.
|
||
struct Placements<'values, 'tree, 'doc> {
|
||
workspace: &'values mut PlacementWorkspace<'tree, 'doc>,
|
||
values: &'values Values,
|
||
}
|
||
|
||
impl Placements<'_, '_, '_> {
|
||
fn world(&mut self, mut occurrence: u64) -> Option<Mat> {
|
||
self.workspace.path.clear();
|
||
let mut t = loop {
|
||
if let Some(t) = self.workspace.placed.get(&occurrence).and_then(Option::as_ref).or_else(|| self.workspace.tree.fixed.get(&occurrence)) {
|
||
break *t;
|
||
}
|
||
if self.workspace.path.len() >= self.workspace.tree.order.len() {
|
||
return None;
|
||
}
|
||
let &(from, joint, from_a) = self.workspace.tree.parent.get(&occurrence)?;
|
||
self.workspace.path.push((occurrence, joint, from_a));
|
||
occurrence = from;
|
||
};
|
||
while let Some((occurrence, joint, from_a)) = self.workspace.path.pop() {
|
||
t = self.workspace.tree.step(joint, from_a, &t, self.values)?;
|
||
#[cfg(test)]
|
||
if !self.workspace.placed.contains_key(&occurrence) {
|
||
tests::PLACEMENT_INSERTS.with(|inserts| inserts.set(inserts.get() + 1));
|
||
}
|
||
self.workspace.placed.insert(occurrence, Some(t));
|
||
}
|
||
Some(t)
|
||
}
|
||
|
||
fn closure_gaps(&mut self, closing: &[u64], scale: f64, out: &mut Vec<f64>) -> Option<()> {
|
||
for id in closing {
|
||
let (joint, frames) = (self.workspace.tree.joints.get(id)?, self.workspace.tree.frames.get(id)?);
|
||
let tb = self.world(joint.b.occurrence)?;
|
||
let ta = self.world(joint.a.occurrence)?;
|
||
let want = self.workspace.tree.step(*id, true, &ta, self.values)?;
|
||
for p in [Vec3::ZERO, Vec3::X * scale, Vec3::Y * scale] {
|
||
let at = apply_point(&frames.b, p);
|
||
let d = apply_point(&want, at) - apply_point(&tb, at);
|
||
out.extend([d.x, d.y, d.z]);
|
||
}
|
||
}
|
||
Some(())
|
||
}
|
||
}
|
||
|
||
/// Values the loop solver moves at most in one group of loops, and loop-closing joints it takes
|
||
/// on at most: larger ones are only checked.
|
||
const MAX_LOOP_VALUES: usize = 64;
|
||
const MAX_LOOPS: usize = 100;
|
||
/// Loop-closing joints one solve takes on at most, over all its groups: a part placed by several
|
||
/// relations closes a loop with each one after the first, so a panel of parts has many small
|
||
/// groups.
|
||
const MAX_CLOSING: usize = 5_000;
|
||
/// Residual evaluations one solve may spend on all its loops.
|
||
const MAX_LOOP_WORK: usize = 200_000;
|
||
|
||
/// Held joint values by (joint, value index): the value each moves from.
|
||
pub type Held = BTreeMap<(u64, usize), f64>;
|
||
|
||
/// The values that set the `around` joints' values through motion links, followed back through
|
||
/// every link to them (several links may write one value; `apply_links`' order decides which
|
||
/// wins on the way) for as many links as `apply_links` passes: all the values reached, and those
|
||
/// that no link sets (the ones a solve can move).
|
||
fn link_chains(asm: &Assembly, tree: &Tree, around: &BTreeSet<u64>, linked: &BTreeSet<(u64, usize)>) -> (BTreeSet<(u64, usize)>, Vec<(u64, usize)>) {
|
||
let (mut feeds, mut starts) = (BTreeSet::new(), Vec::new());
|
||
let mut frontier: BTreeSet<(u64, usize)> =
|
||
around.iter().filter_map(|id| tree.joints.get(id)).flat_map(|j| (0..j.kind.dofs().len()).map(|i| (j.id, i))).collect();
|
||
let mut seen = frontier.clone();
|
||
for _ in 0..MAX_LINK_PASSES {
|
||
let next: BTreeSet<(u64, usize)> =
|
||
asm.links.iter().filter(|l| frontier.contains(&(l.b, l.ib))).map(|l| (l.a, l.ia)).filter(|v| !seen.contains(v)).collect();
|
||
if next.is_empty() {
|
||
break;
|
||
}
|
||
for &(id, i) in &next {
|
||
feeds.insert((id, i));
|
||
if !linked.contains(&(id, i)) && tree.joints.get(&id).is_some_and(|j| i < j.kind.dofs().len()) {
|
||
starts.push((id, i));
|
||
}
|
||
}
|
||
seen.extend(next.iter().copied());
|
||
frontier = next;
|
||
}
|
||
(feeds, starts)
|
||
}
|
||
|
||
/// The values that move each value a motion link sets: the values its link chain starts from,
|
||
/// which no link sets (none for a chain that comes back round on itself, which only a hand-edited
|
||
/// design has). A driven gear's turn is its driving gear's: one degree of freedom, not two.
|
||
fn link_sources(asm: &Assembly) -> BTreeMap<(u64, usize), BTreeSet<(u64, usize)>> {
|
||
let mut into: BTreeMap<(u64, usize), Vec<(u64, usize)>> = BTreeMap::new();
|
||
for l in &asm.links {
|
||
into.entry((l.b, l.ib)).or_default().push((l.a, l.ia));
|
||
}
|
||
let mut sources = BTreeMap::new();
|
||
if into.is_empty() {
|
||
return sources;
|
||
}
|
||
// A link from a value its joint doesn't have (a hand-edited design) moves nothing.
|
||
let real: BTreeSet<(u64, usize)> = asm.joints.iter().flat_map(|j| (0..j.kind.dofs().len()).map(|i| (j.id, i))).collect();
|
||
for &v in into.keys() {
|
||
// Back along the links, as far as a link chain carries a value (`MAX_LINK_PASSES`).
|
||
let (mut from, mut seen) = (BTreeSet::new(), BTreeSet::from([v]));
|
||
let mut frontier = vec![v];
|
||
for _ in 0..MAX_LINK_PASSES {
|
||
let mut next = Vec::new();
|
||
for w in frontier.iter().filter_map(|w| into.get(w)).flatten() {
|
||
if !seen.insert(*w) {
|
||
continue;
|
||
}
|
||
if into.contains_key(w) {
|
||
next.push(*w);
|
||
} else if real.contains(w) {
|
||
from.insert(*w);
|
||
}
|
||
}
|
||
if next.is_empty() {
|
||
break;
|
||
}
|
||
frontier = next;
|
||
}
|
||
sources.insert(v, from);
|
||
}
|
||
sources
|
||
}
|
||
|
||
/// The held values among `touches` that move: (joint, index, from, to), `from` within the
|
||
/// joint's limits. A suppressed joint still sets values through its motion links.
|
||
fn held_moves(asm: &Assembly, held: &Held, touches: &BTreeSet<(u64, usize)>, vals: &Values) -> Vec<(u64, usize, f64, f64)> {
|
||
let mut moves = Vec::new();
|
||
for ((id, i), from) in held.iter().filter(|(v, _)| touches.contains(v)) {
|
||
let (Some(j), Some(to)) = (asm.joints.iter().find(|j| j.id == *id), vals.get(id).and_then(|q| q.get(*i))) else { continue };
|
||
let from = match j.limits.get(*i).copied().flatten() {
|
||
Some((lo, hi)) => from.max(lo.min(hi)).min(hi.max(lo)),
|
||
None => *from,
|
||
};
|
||
if from != *to {
|
||
moves.push((*id, *i, from, *to));
|
||
}
|
||
}
|
||
moves
|
||
}
|
||
|
||
/// Close the loops, each group of loops that share joints on its own: see `close_group`.
|
||
/// Returns the moved joints' new stored values (and updates `vals`), and the closing joints of
|
||
/// the groups whose held values moved but which can't stay closed on the way (nothing in those
|
||
/// moves; a group that can't close without moving is left to the conflict check).
|
||
fn close_loops(tree: &Tree, closing: &[u64], asm: &Assembly, held: &Held, vals: &mut Values) -> (Values, BTreeSet<u64>) {
|
||
let (mut changed, mut stuck) = (BTreeMap::new(), BTreeSet::new());
|
||
if closing.len() > MAX_CLOSING {
|
||
return (Values::new(), stuck);
|
||
}
|
||
let linked = set_values(asm);
|
||
let groups = loop_groups(tree, closing, asm, &linked);
|
||
let spent = std::cell::Cell::new(0usize);
|
||
for (group, around, touches) in groups.iter().filter(|(c, _, _)| c.len() <= MAX_LOOPS) {
|
||
let moves = held_moves(asm, held, touches, vals);
|
||
match close_group(tree, group, around, &moves, asm, held, &linked, &spent, vals) {
|
||
Some(m) => changed.extend(m),
|
||
None if !moves.is_empty() => stuck.extend(group.iter().copied()),
|
||
None => {}
|
||
}
|
||
}
|
||
// The stored values with what each group moved (groups may move different values of one
|
||
// joint).
|
||
let mut moved = Values::new();
|
||
for ((id, i), v) in changed {
|
||
let Some(j) = tree.joints.get(&id) else { continue };
|
||
let q = moved.entry(id).or_insert_with(|| {
|
||
let mut q = j.values.clone();
|
||
q.resize(j.kind.dofs().len(), 0.0);
|
||
q
|
||
});
|
||
if let Some(slot) = q.get_mut(i) {
|
||
*slot = v;
|
||
}
|
||
}
|
||
(moved, stuck)
|
||
}
|
||
|
||
/// A group of loops solved together: its closing joints, the joints around them, and the values
|
||
/// it touches.
|
||
type Group = (Vec<u64>, BTreeSet<u64>, BTreeSet<(u64, usize)>);
|
||
|
||
/// The loops' groups. Each loop: its closing joint and the joints on the tree paths between its
|
||
/// sides; loops that share a value (of a joint, or one feeding them through links) are solved
|
||
/// together.
|
||
fn loop_groups(tree: &Tree, closing: &[u64], asm: &Assembly, linked: &BTreeSet<(u64, usize)>) -> Vec<Group> {
|
||
let mut groups: Vec<Group> = Vec::new();
|
||
for id in closing {
|
||
let Some(j) = tree.joints.get(id) else { continue };
|
||
// A joint between an occurrence and itself (only a hand-edited file has one) is only checked.
|
||
if j.a.occurrence == j.b.occurrence {
|
||
continue;
|
||
}
|
||
let side = |occ: u64| -> BTreeSet<u64> { tree.path(occ).1.iter().map(|(k, _)| *k).collect() };
|
||
let mut around: BTreeSet<u64> = side(j.a.occurrence).symmetric_difference(&side(j.b.occurrence)).copied().collect();
|
||
around.insert(*id);
|
||
// The values the loop depends on: its joints' and those its links read. Loops tie together
|
||
// through a shared value only (a rigid joint on both paths has none; two values of one
|
||
// joint can feed two independent loops).
|
||
let mut touches = link_chains(asm, tree, &around, linked).0;
|
||
touches.extend(around.iter().filter_map(|id| tree.joints.get(id)).flat_map(|j| (0..j.kind.dofs().len()).map(|i| (j.id, i))));
|
||
let mut members = vec![*id];
|
||
groups.retain(|(c, a, t)| {
|
||
if t.is_disjoint(&touches) {
|
||
return true;
|
||
}
|
||
members.extend(c.iter().copied());
|
||
around.extend(a.iter().copied());
|
||
touches.extend(t.iter().copied());
|
||
false
|
||
});
|
||
groups.push((members, around, touches));
|
||
}
|
||
groups
|
||
}
|
||
|
||
/// The values a solve of the loops `around` moves: every value of their joints but the `held`
|
||
/// ones and motion-link targets, and the values the targets' link chains start from.
|
||
fn unknowns(tree: &Tree, around: &BTreeSet<u64>, asm: &Assembly, linked: &BTreeSet<(u64, usize)>, held: &Held) -> Vec<(u64, usize)> {
|
||
let mut vars: Vec<(u64, usize)> = Vec::new();
|
||
for j in around.iter().filter_map(|id| tree.joints.get(id)) {
|
||
vars.extend((0..j.kind.dofs().len()).map(|i| (j.id, i)).filter(|v| !linked.contains(v) && !held.contains_key(v)));
|
||
}
|
||
for v in link_chains(asm, tree, around, linked).1 {
|
||
if !held.contains_key(&v) && !vars.contains(&v) {
|
||
vars.push(v);
|
||
}
|
||
}
|
||
vars
|
||
}
|
||
|
||
/// Each value's limits, or none.
|
||
fn limit_bounds(tree: &Tree, vars: &[(u64, usize)]) -> Vec<(f64, f64)> {
|
||
vars.iter()
|
||
.map(|(id, i)| match tree.joints.get(id).and_then(|j| j.limits.get(*i).copied().flatten()) {
|
||
Some((lo, hi)) => (lo.min(hi), hi.max(lo)),
|
||
None => (f64::NEG_INFINITY, f64::INFINITY),
|
||
})
|
||
.collect()
|
||
}
|
||
|
||
/// The loops' size: the diagonal of the box around their joints' A frames, 1 mm to 1 km. Points
|
||
/// that far apart weigh turns like moves.
|
||
fn loop_scale(tree: &Tree, around: &BTreeSet<u64>, vals: &Values) -> f64 {
|
||
let joints: Aabb3 = around
|
||
.iter()
|
||
.filter_map(|id| {
|
||
let (j, frames) = (tree.joints.get(id)?, tree.frames.get(id)?);
|
||
Some(apply_point(&mat_mul(&tree.world(j.a.occurrence, vals)?, &frames.a), Vec3::ZERO))
|
||
})
|
||
.collect();
|
||
if joints.is_empty() { 1.0 } else { joints.diagonal().clamp(1.0, 1e6) }
|
||
}
|
||
|
||
/// How far each closing joint is from meeting: three points of B's joint frame, `scale` apart,
|
||
/// where the joint wants them against where the tree puts them (appended to `out`).
|
||
fn closure_gaps(workspace: &mut PlacementWorkspace, closing: &[u64], vals: &Values, scale: f64, out: &mut Vec<f64>) -> Option<()> {
|
||
workspace.at(vals).closure_gaps(closing, scale, out)
|
||
}
|
||
|
||
/// How far a closing joint may be off before it is a conflict: its frames apart by more than
|
||
/// this many millimetres or turned by more than this many radians (a micrometre over a metre).
|
||
/// Holes picked on parts are rarely exactly in line: axes a few hundredths of a microradian
|
||
/// apart (#6211) are not a conflict, and the loop through them still moves.
|
||
const CONFLICT_MM: f64 = 1e-4;
|
||
const CONFLICT_RAD: f64 = 1e-6;
|
||
|
||
/// The largest gap (`closure_gaps`, for loops of size `scale`) that still passes the conflict
|
||
/// check, with room to spare.
|
||
fn loose_gap(scale: f64) -> f64 {
|
||
CONFLICT_MM.min(CONFLICT_RAD * scale) / 4.0
|
||
}
|
||
|
||
/// Close loops whose gaps `f` gives from `x`, and the tolerance to keep them closed to from here
|
||
/// on: `tol`, or, where they come no closer than that but within `loose`, a little more than they
|
||
/// do come. Faces modelled a few nanometres apart along parallel axes, or axes a hair out of
|
||
/// parallel, leave a gap no value of a planar loop takes out (the second one that grows as the
|
||
/// loop turns); the loop still moves, as closed as it comes. `None` when they can't close.
|
||
fn close_within(f: &mut dyn FnMut(&[f64]) -> Option<Vec<f64>>, x: &mut Vec<f64>, bounds: &[(f64, f64)], tol: f64, loose: f64) -> Option<f64> {
|
||
if least_squares(f, x, bounds, tol) {
|
||
return Some(tol);
|
||
}
|
||
let left = largest(&f(x)?);
|
||
(left <= loose).then(|| (4.0 * left).clamp(tol, loose.max(tol)))
|
||
}
|
||
|
||
/// Occurrences whose degrees of freedom are worked out through their loops, at most; the rest
|
||
/// keep the tree's count.
|
||
const MAX_DOF_OCCURRENCES: usize = 256;
|
||
|
||
/// How far `nearby_pose` moves each value: radians for an angle, a share of the loops' size for a
|
||
/// distance. Far enough for a part's motion that vanishes at a dead point to show in a rank, near
|
||
/// enough to stay on the mechanism's branch.
|
||
const NUDGE: f64 = 1e-3;
|
||
|
||
/// A pose of the loops near `vals`: each value they move nudged by an amount of its own within
|
||
/// its limits (so the nudge points in no special direction), then each group of loops closed
|
||
/// again. A group that can't close again, or only further away than a few nudges (on another
|
||
/// branch), keeps its values. It has a work budget of its own.
|
||
fn nearby_pose(tree: &Tree, groups: &[Group], asm: &Assembly, linked: &BTreeSet<(u64, usize)>, vals: &Values) -> Values {
|
||
let mut near = vals.clone();
|
||
let mut spent = 0usize;
|
||
for (closing, around, _) in groups {
|
||
let vars = unknowns(tree, around, asm, linked, &Held::new());
|
||
if vars.is_empty() || vars.len() > MAX_LOOP_VALUES {
|
||
continue;
|
||
}
|
||
let scale = loop_scale(tree, around, vals);
|
||
let step: Vec<f64> =
|
||
vars.iter().map(|(id, i)| NUDGE * if tree.joints.get(id).is_some_and(|j| j.kind.is_angle(*i)) { 1.0 } else { scale }).collect();
|
||
let bounds = limit_bounds(tree, &vars);
|
||
let x0: Vec<f64> = vars.iter().map(|(id, i)| near.get(id).and_then(|q| q.get(*i)).copied().unwrap_or(0.0)).collect();
|
||
let mut x: Vec<f64> = x0
|
||
.iter()
|
||
.zip(step.iter().zip(&bounds))
|
||
.enumerate()
|
||
.map(|(k, (v, (d, (lo, hi))))| {
|
||
// 0.5 to 1.5 nudges, alternately up and down.
|
||
let w = 0.5 + (k as f64 * 0.618_034).fract();
|
||
(v + d * if k % 2 == 0 { w } else { -w }).max(*lo).min(*hi)
|
||
})
|
||
.collect();
|
||
let mut workspace = PlacementWorkspace::new(tree);
|
||
let mut work = near.clone();
|
||
let mut gaps = |x: &[f64]| -> Option<Vec<f64>> {
|
||
spent += 1;
|
||
if spent > MAX_LOOP_WORK {
|
||
return None;
|
||
}
|
||
for ((id, i), v) in vars.iter().zip(x) {
|
||
if let Some(slot) = work.get_mut(id).and_then(|q| q.get_mut(*i)) {
|
||
*slot = *v;
|
||
}
|
||
}
|
||
apply_links(asm, &mut work);
|
||
let mut out = Vec::with_capacity(closing.len() * 9);
|
||
closure_gaps(&mut workspace, closing, &work, scale, &mut out)?;
|
||
out.iter().all(|v| v.is_finite()).then_some(out)
|
||
};
|
||
if close_within(&mut gaps, &mut x, &bounds, (1e-10 * scale).min(1e-7), loose_gap(scale)).is_some()
|
||
&& x.iter().zip(&x0).zip(&step).all(|((a, b), d)| (a - b).abs() <= 4.0 * d)
|
||
&& gaps(&x).is_some()
|
||
{
|
||
near = work;
|
||
}
|
||
}
|
||
near
|
||
}
|
||
|
||
/// The degrees of freedom of the occurrences loops constrain: how many independent ways each can
|
||
/// still move with every loop kept closed, the rank of its placement over the joint values once
|
||
/// the loops' closure is taken out (rank [J_loops; J_placement] - rank J_loops). An occurrence's
|
||
/// values are those on its tree path and the unknowns of the loops on that path. It is counted at
|
||
/// the pose and at a pose nearby, and the larger count stands: at a dead point of its loop (an
|
||
/// actuator in line with the path of its tip pin) a part's motion vanishes to first order, so the
|
||
/// pose alone counts 0. The tree's count stands where a loop group is over the solver's caps or
|
||
/// the work runs out.
|
||
fn loop_dof(tree: &Tree, closing: &[u64], asm: &Assembly, vals: &Values, dof: &mut BTreeMap<u64, usize>) {
|
||
if closing.len() > MAX_CLOSING {
|
||
return;
|
||
}
|
||
let linked = set_values(asm);
|
||
let mut groups = loop_groups(tree, closing, asm, &linked);
|
||
groups.retain(|(c, _, _)| c.len() <= MAX_LOOPS);
|
||
// The joints loops depend on: those around them, those whose values they read, and those a
|
||
// motion link carries any of these values into.
|
||
let mut relevant: BTreeSet<u64> = groups.iter().flat_map(|(_, a, t)| a.iter().copied().chain(t.iter().map(|(j, _)| *j))).collect();
|
||
for _ in 0..MAX_LINK_PASSES {
|
||
let more: Vec<u64> = asm.links.iter().filter(|l| relevant.contains(&l.a) && !relevant.contains(&l.b)).map(|l| l.b).collect();
|
||
if more.is_empty() {
|
||
break;
|
||
}
|
||
relevant.extend(more);
|
||
}
|
||
// The occurrences a loop may hold or move: placed by such a joint, or below one that is
|
||
// (worked out down the tree, parents first). The others keep the tree's count.
|
||
let mut candidates: BTreeSet<u64> = BTreeSet::new();
|
||
for occ in &tree.order {
|
||
if let Some(&(from, joint, _)) = tree.parent.get(occ)
|
||
&& (relevant.contains(&joint) || candidates.contains(&from))
|
||
{
|
||
candidates.insert(*occ);
|
||
}
|
||
}
|
||
let (mut spent, mut counted) = (0usize, 0usize);
|
||
// A pose nearby, when one differs.
|
||
let near = (!candidates.is_empty()).then(|| nearby_pose(tree, &groups, asm, &linked, vals)).filter(|n| n != vals);
|
||
for occ in tree.order.iter().filter(|o| candidates.contains(o)) {
|
||
let path: Vec<u64> = tree.path(*occ).1.iter().map(|(k, _)| *k).collect();
|
||
let (mut values, mut have): (Vec<(u64, usize)>, BTreeSet<(u64, usize)>) = (Vec::new(), BTreeSet::new());
|
||
let mut add = |values: &mut Vec<(u64, usize)>, v: (u64, usize)| {
|
||
if have.insert(v) {
|
||
values.push(v);
|
||
}
|
||
};
|
||
for j in path.iter().filter_map(|k| tree.joints.get(k)) {
|
||
for v in (0..j.kind.dofs().len()).map(|i| (j.id, i)).filter(|v| !linked.contains(v)) {
|
||
add(&mut values, v);
|
||
}
|
||
if values.len() > MAX_LOOP_VALUES {
|
||
break;
|
||
}
|
||
}
|
||
if values.len() > MAX_LOOP_VALUES {
|
||
continue;
|
||
}
|
||
// A value on the path a motion link sets moves with the values its link chain starts from.
|
||
let on_path: BTreeSet<u64> = path.iter().copied().collect();
|
||
for v in link_chains(asm, tree, &on_path, &linked).1 {
|
||
add(&mut values, v);
|
||
}
|
||
// The loops on the path, and every loop whose values those reach (a linked source may be
|
||
// held by a loop of its own), each once.
|
||
let (mut closers, mut around) = (Vec::new(), BTreeSet::new());
|
||
let mut taken: BTreeSet<usize> = BTreeSet::new();
|
||
loop {
|
||
let more: Vec<usize> = groups
|
||
.iter()
|
||
.enumerate()
|
||
.filter(|(g, _)| !taken.contains(g))
|
||
.filter(|(_, (_, a, t))| path.iter().any(|k| a.contains(k)) || t.iter().any(|v| values.contains(v)))
|
||
.map(|(g, _)| g)
|
||
.collect();
|
||
if more.is_empty() {
|
||
break;
|
||
}
|
||
for (c, a, _) in more.iter().filter_map(|g| groups.get(*g)) {
|
||
closers.extend(c.iter().copied());
|
||
around.extend(a.iter().copied());
|
||
for v in unknowns(tree, a, asm, &linked, &Held::new()) {
|
||
add(&mut values, v);
|
||
}
|
||
}
|
||
taken.extend(more);
|
||
}
|
||
// No loop reaches this occurrence's values (not even through a motion link it drives):
|
||
// the tree's count stands.
|
||
if taken.is_empty() {
|
||
continue;
|
||
}
|
||
counted += 1;
|
||
if counted > MAX_DOF_OCCURRENCES || spent > MAX_LOOP_WORK {
|
||
return;
|
||
}
|
||
if values.len() > MAX_LOOP_VALUES {
|
||
continue;
|
||
}
|
||
let scale = loop_scale(tree, &around, vals);
|
||
let (n, gaps) = (values.len(), closers.len() * 9);
|
||
// How many ways the occurrence moves at a pose, with the loops kept closed.
|
||
let mut free_at = |at: &Values| -> Option<usize> {
|
||
let mut workspace = PlacementWorkspace::new(tree);
|
||
let mut work = at.clone();
|
||
// The loops' gaps, then three points of the occurrence `scale` apart.
|
||
let mut f = |x: &[f64]| -> Option<Vec<f64>> {
|
||
spent += 1;
|
||
for ((id, i), v) in values.iter().zip(x) {
|
||
if let Some(slot) = work.get_mut(id).and_then(|q| q.get_mut(*i)) {
|
||
*slot = *v;
|
||
}
|
||
}
|
||
apply_links(asm, &mut work);
|
||
let mut out = Vec::with_capacity(closers.len() * 9 + 9);
|
||
let mut placed = workspace.at(&work);
|
||
placed.closure_gaps(&closers, scale, &mut out)?;
|
||
let t = placed.world(*occ)?;
|
||
for p in [Vec3::ZERO, Vec3::X * scale, Vec3::Y * scale] {
|
||
let q = apply_point(&t, p);
|
||
out.extend([q.x, q.y, q.z]);
|
||
}
|
||
out.iter().all(|v| v.is_finite()).then_some(out)
|
||
};
|
||
let x0: Vec<f64> = values.iter().map(|(id, i)| at.get(id).and_then(|q| q.get(*i)).copied().unwrap_or(0.0)).collect();
|
||
let jac = jacobian(&mut f, &x0, gaps + 9)?;
|
||
let rank = |rows: usize| {
|
||
let mut a = linalg::Mat::zeros(rows, n);
|
||
let mut big = 0.0f64;
|
||
for r in 0..rows {
|
||
for c in 0..n {
|
||
let v = jac.get(r * n + c).copied().unwrap_or(0.0);
|
||
big = big.max(v.abs());
|
||
a.set(r, c, v);
|
||
}
|
||
}
|
||
linalg::rref(&mut a, 1e-6 * big.max(1.0)).len()
|
||
};
|
||
Some(rank(gaps + 9).saturating_sub(rank(gaps)))
|
||
};
|
||
let here = free_at(vals);
|
||
let there = near.as_ref().and_then(&mut free_at);
|
||
let Some(free) = here.max(there) else { continue };
|
||
dof.insert(*occ, free.min(6));
|
||
}
|
||
}
|
||
|
||
/// Close one group of loops: move the values of the joints `around` them (all but the `held`
|
||
/// values, motion-link targets and rigid joints, within their limits; a linked value moves
|
||
/// through the start of its link chain) until every loop-closing joint meets. A loop open at the
|
||
/// start is closed first, from where it is. Then the held values `moves` go from the values they
|
||
/// are held from to their current ones in small steps, each solved from the last, so the mechanism
|
||
/// stays on its branch (an open four-bar does not flip crossed). Returns the values that changed
|
||
/// from what is stored, by (joint, index), and updates `vals` (empty when there is nothing to do
|
||
/// or the group is too big to solve), or `None` when the loops can't close, or can't stay closed
|
||
/// on the way.
|
||
fn close_group(
|
||
tree: &Tree,
|
||
closing: &[u64],
|
||
around: &BTreeSet<u64>,
|
||
moves: &[(u64, usize, f64, f64)],
|
||
asm: &Assembly,
|
||
held: &Held,
|
||
linked: &BTreeSet<(u64, usize)>,
|
||
spent: &std::cell::Cell<usize>,
|
||
vals: &mut Values,
|
||
) -> Option<BTreeMap<(u64, usize), f64>> {
|
||
let vars = unknowns(tree, around, asm, linked, held);
|
||
if vars.len() > MAX_LOOP_VALUES {
|
||
return Some(BTreeMap::new());
|
||
}
|
||
let bounds = limit_bounds(tree, &vars);
|
||
let scale = loop_scale(tree, around, vals);
|
||
// Closer than the conflict check needs: 1e-7 mm, and turns of 1e-10 rad across the loop.
|
||
let tol = (1e-10 * scale).min(1e-7);
|
||
// The values with the held ones `t` of the way along (and the unknowns at `x`).
|
||
let place = |work: &mut Values, x: &[f64], t: f64| {
|
||
for (id, i, from, to) in moves {
|
||
if let Some(slot) = work.get_mut(id).and_then(|q| q.get_mut(*i)) {
|
||
*slot = from + (to - from) * t;
|
||
}
|
||
}
|
||
for ((id, i), (v, (lo, hi))) in vars.iter().zip(x.iter().zip(&bounds)) {
|
||
if let Some(slot) = work.get_mut(id).and_then(|q| q.get_mut(*i)) {
|
||
*slot = v.max(*lo).min(*hi);
|
||
}
|
||
}
|
||
apply_links(asm, work);
|
||
};
|
||
let x0: Vec<f64> = vars.iter().map(|(id, i)| vals.get(id).and_then(|q| q.get(*i)).copied().unwrap_or(0.0)).collect();
|
||
// Steps that move no value around the loops (links included) more than 5 degrees or a
|
||
// twentieth of the loops' size.
|
||
// How many such steps apart two sets of values are, over the loops' values.
|
||
let stride = |a: &Values, b: &Values| -> f64 {
|
||
let mut most = 0.0f64;
|
||
for j in around.iter().filter_map(|id| tree.joints.get(id)) {
|
||
for i in 0..j.kind.dofs().len() {
|
||
let (Some(p), Some(q)) = (a.get(&j.id).and_then(|v| v.get(i)), b.get(&j.id).and_then(|v| v.get(i))) else { continue };
|
||
let step = if j.kind.is_angle(i) { 5f64.to_radians() } else { 0.05 * scale };
|
||
most = most.max((q - p).abs() / step);
|
||
}
|
||
}
|
||
most
|
||
};
|
||
let effective = |x: &[f64], t: f64| {
|
||
let mut v = vals.clone();
|
||
place(&mut v, x, t);
|
||
v
|
||
};
|
||
let mut first = 1.0f64;
|
||
if !moves.is_empty() {
|
||
first = first.min(1.0 / stride(&effective(&x0, 0.0), &effective(&x0, 1.0)));
|
||
}
|
||
let mut workspace = PlacementWorkspace::new(tree);
|
||
let mut work = vals.clone();
|
||
// How far each closing joint is from meeting with the held values `t` of the way along:
|
||
// three points of B's joint frame, where the joint wants them against where the tree puts them.
|
||
let mut gaps = |x: &[f64], t: f64| -> Option<Vec<f64>> {
|
||
spent.set(spent.get() + 1);
|
||
if spent.get() > MAX_LOOP_WORK {
|
||
return None;
|
||
}
|
||
place(&mut work, x, t);
|
||
let mut out = Vec::with_capacity(closing.len() * 9);
|
||
closure_gaps(&mut workspace, closing, &work, scale, &mut out)?;
|
||
out.iter().all(|v| v.is_finite()).then_some(out)
|
||
};
|
||
// Already closed, with no held value moving. (A moving one is followed all the way: a
|
||
// rocker driven a full turn ends where it started, but can't get there.)
|
||
if moves.is_empty() && gaps(&x0, 1.0).is_some_and(|r| largest(&r) <= tol) {
|
||
return Some(BTreeMap::new());
|
||
}
|
||
// A loop open at the start closes first. One that comes only to within the conflict check
|
||
// (`close_within`) moves on as closed as it is; with nothing held moving, one that started
|
||
// that close is left as it is.
|
||
let mut x = x0;
|
||
let start = largest(&gaps(&x, 0.0)?);
|
||
let loose = loose_gap(scale);
|
||
let tol = match close_within(&mut |x| gaps(x, 0.0), &mut x, &bounds, tol, loose)? {
|
||
t if t > tol && moves.is_empty() && start <= t => return Some(BTreeMap::new()),
|
||
t => t,
|
||
};
|
||
let (mut t, mut dt) = (if moves.is_empty() { 1.0 } else { 0.0 }, first);
|
||
let mut at = effective(&x, t);
|
||
while t < 1.0 {
|
||
if dt < first * 1e-4 {
|
||
return None;
|
||
}
|
||
let t1 = (t + dt).min(1.0);
|
||
let mut trial = x.clone();
|
||
// Each step as closed as the start, or within the conflict check where the loop's gap
|
||
// grows as it moves (axes a hair out of parallel, #6211).
|
||
if close_within(&mut |x| gaps(x, t1), &mut trial, &bounds, tol, loose).is_some() {
|
||
// A step that moved some loop value too far (through a link and a limit, or close to
|
||
// a dead point) is taken again in halves.
|
||
let next = effective(&trial, t1);
|
||
if stride(&at, &next) > 2.0 {
|
||
dt *= 0.5;
|
||
continue;
|
||
}
|
||
(x, t, dt, at) = (trial, t1, (dt * 2.0).min(first), next);
|
||
} else if spent.get() > MAX_LOOP_WORK {
|
||
return None;
|
||
} else {
|
||
dt *= 0.5;
|
||
}
|
||
}
|
||
if largest(&gaps(&x, 1.0)?) > tol.max(loose) {
|
||
return None;
|
||
}
|
||
// The values that changed from what is stored.
|
||
let moved = vars
|
||
.iter()
|
||
.zip(&x)
|
||
.filter(|((id, i), v)| tree.joints.get(id).is_some_and(|j| j.values.get(*i).is_none_or(|s| (s - *v).abs() > 1e-12)))
|
||
.map(|(var, v)| (*var, *v))
|
||
.collect();
|
||
*vals = work;
|
||
Some(moved)
|
||
}
|
||
|
||
fn largest(r: &[f64]) -> f64 {
|
||
r.iter().fold(0.0f64, |m, v| m.max(v.abs()))
|
||
}
|
||
|
||
/// Levenberg–Marquardt: move `x` (kept within `bounds`) until every value of `f` is within
|
||
/// `tol` of zero. False when it can't get there.
|
||
/// The Jacobian of `f` (`m` values) at `x` by central differences, row-major.
|
||
fn jacobian(f: &mut dyn FnMut(&[f64]) -> Option<Vec<f64>>, x: &[f64], m: usize) -> Option<Vec<f64>> {
|
||
const H: f64 = 1e-6;
|
||
let n = x.len();
|
||
let mut jac = vec![0.0; m * n];
|
||
for k in 0..n {
|
||
let (mut xp, mut xm) = (x.to_vec(), x.to_vec());
|
||
if let (Some(p), Some(q)) = (xp.get_mut(k), xm.get_mut(k)) {
|
||
*p += H;
|
||
*q -= H;
|
||
}
|
||
let (rp, rm) = (f(&xp)?, f(&xm)?);
|
||
for (i, (a, b)) in rp.iter().zip(&rm).enumerate().take(m) {
|
||
if let Some(slot) = jac.get_mut(i * n + k) {
|
||
*slot = (a - b) / (2.0 * H);
|
||
}
|
||
}
|
||
}
|
||
Some(jac)
|
||
}
|
||
|
||
fn least_squares(f: &mut dyn FnMut(&[f64]) -> Option<Vec<f64>>, x: &mut Vec<f64>, bounds: &[(f64, f64)], tol: f64) -> bool {
|
||
let n = x.len();
|
||
let norm = |r: &[f64]| r.iter().map(|v| v * v).sum::<f64>();
|
||
let Some(mut r) = f(x) else { return false };
|
||
if n == 0 {
|
||
return largest(&r) <= tol;
|
||
}
|
||
let mut lambda = 1e-3;
|
||
for _ in 0..50 {
|
||
if largest(&r) <= tol {
|
||
return true;
|
||
}
|
||
// The Jacobian by central differences, then the normal equations JᵀJ δ = −Jᵀr.
|
||
let m = r.len();
|
||
let Some(jac) = jacobian(f, x, m) else { return false };
|
||
let mut jtj = linalg::Mat::zeros(n, n);
|
||
let mut g = vec![0.0; n];
|
||
for (i, ri) in r.iter().enumerate() {
|
||
let row = jac.get(i * n..(i + 1) * n).unwrap_or(&[]);
|
||
for (p, a) in row.iter().enumerate().filter(|(_, a)| **a != 0.0) {
|
||
if let Some(gp) = g.get_mut(p) {
|
||
*gp -= a * ri;
|
||
}
|
||
for (q, b) in row.iter().enumerate().skip(p) {
|
||
jtj.add(p, q, a * b);
|
||
}
|
||
}
|
||
}
|
||
for p in 0..n {
|
||
for q in 0..p {
|
||
jtj.set(p, q, jtj.get(q, p));
|
||
}
|
||
}
|
||
let mut stepped = false;
|
||
while lambda < 1e12 {
|
||
let mut a = jtj.clone();
|
||
for p in 0..n {
|
||
a.add(p, p, lambda * (1.0 + jtj.get(p, p)));
|
||
}
|
||
if let Some(d) = linalg::solve(a, g.clone()) {
|
||
let next: Vec<f64> = x.iter().zip(&d).zip(bounds).map(|((v, dv), (lo, hi))| (v + dv).max(*lo).min(*hi)).collect();
|
||
if let Some(rn) = f(&next)
|
||
&& norm(&rn) < norm(&r)
|
||
{
|
||
*x = next;
|
||
r = rn;
|
||
lambda = (lambda / 3.0).max(1e-9);
|
||
stepped = true;
|
||
break;
|
||
}
|
||
}
|
||
lambda *= 4.0;
|
||
}
|
||
if !stepped {
|
||
return false;
|
||
}
|
||
}
|
||
largest(&r) <= tol
|
||
}
|
||
|
||
/// Place occurrences from the joint graph.
|
||
pub fn solve(doc: &Document, st: &ModelState) -> Solution {
|
||
solve_holding(doc, st, &BTreeMap::new())
|
||
}
|
||
|
||
/// Place occurrences from the joint graph. Joints that close loops are met by moving the values
|
||
/// of the other joints around the loop. The `held` values (the ones being driven) keep theirs,
|
||
/// moving there from the values given (where the loops last closed) so the others follow them.
|
||
pub fn solve_holding(doc: &Document, st: &ModelState, held: &Held) -> Solution {
|
||
solve_holding_with_analysis(doc, st, held, Analysis::DegreesOfFreedom)
|
||
}
|
||
|
||
/// Place occurrences and check constraints with the requested diagnostic work. Placement-only
|
||
/// solves still close and check every loop, respect held values and limits, and report errors;
|
||
/// they leave `Solution::dof` empty rather than returning the spanning tree's approximate count.
|
||
pub fn solve_holding_with_analysis(doc: &Document, st: &ModelState, held: &Held, analysis: Analysis) -> Solution {
|
||
let asm = &doc.assembly;
|
||
let mut sol = Solution::default();
|
||
let mut vals = joint_values(asm);
|
||
let Built { tree, mut placed, closing, mut dof } = build(doc, st, &vals, &mut sol);
|
||
let mut stuck = BTreeSet::new();
|
||
if !closing.is_empty() {
|
||
(sol.values, stuck) = close_loops(&tree, &closing, asm, held, &mut vals);
|
||
if !sol.values.is_empty() {
|
||
placed = tree.place(&vals);
|
||
}
|
||
}
|
||
for id in &closing {
|
||
let Some(j) = tree.joints.get(id) else { continue };
|
||
let (Some(ta), Some(tb)) = (placed.get(&j.a.occurrence), placed.get(&j.b.occurrence)) else { continue };
|
||
let (Some(want), Some(frames)) = (tree.step(*id, true, ta, &vals), tree.frames.get(id)) else { continue };
|
||
// Measured at the joint, where the loop solver closes it.
|
||
let (dt, da) = mismatch(&mat_mul(&want, &frames.b), &mat_mul(tb, &frames.b));
|
||
if dt > CONFLICT_MM || da > CONFLICT_RAD {
|
||
sol.conflicts.push((
|
||
j.id,
|
||
j.name.clone(),
|
||
format!("off by {dt:.4} mm and {:.3}° from the placement the other joints give", da.to_degrees()),
|
||
));
|
||
} else if stuck.contains(id) {
|
||
// It meets there, but the loop would have to come apart on the way (a rocker
|
||
// driven a full turn ends where it started).
|
||
sol.conflicts.push((j.id, j.name.clone(), "the loop can't stay closed on the way to these values".into()));
|
||
}
|
||
}
|
||
if analysis == Analysis::DegreesOfFreedom {
|
||
if !closing.is_empty() {
|
||
loop_dof(&tree, &closing, asm, &vals, &mut dof);
|
||
}
|
||
for o in &doc.occurrences {
|
||
dof.entry(o.id).or_insert(6);
|
||
}
|
||
} else {
|
||
dof.clear();
|
||
}
|
||
placed.remove(&0);
|
||
sol.world = placed;
|
||
sol.dof = dof;
|
||
sol
|
||
}
|
||
|
||
/// The joint graph laid out for a solve: the tree, where it places each occurrence for the
|
||
/// values it was built with, the joints that close loops, and each occurrence's degrees of
|
||
/// freedom along the tree.
|
||
struct Built<'a> {
|
||
tree: Tree<'a>,
|
||
placed: BTreeMap<u64, Mat>,
|
||
closing: Vec<u64>,
|
||
dof: BTreeMap<u64, usize>,
|
||
}
|
||
|
||
/// Lay out the joint graph: the spanning tree out from the fixed occurrences (the root, grounded
|
||
/// ones; with neither involved, the first joint's A side) and the joints left over, which close
|
||
/// loops. Joints whose origins can't be resolved go to `sol.errors`; `sol.fixed` is set.
|
||
fn build<'a>(doc: &'a Document, st: &ModelState, vals: &Values, sol: &mut Solution) -> Built<'a> {
|
||
let asm = &doc.assembly;
|
||
let joints: Vec<&Joint> = asm.joints.iter().filter(|j| !j.suppressed).take(MAX_JOINTS).collect();
|
||
// Joint frames in component coordinates (errors leave the joint out). An origin several joints
|
||
// share (a panel face every part sits on) is found once.
|
||
let mut frames: BTreeMap<u64, JointFrames> = BTreeMap::new();
|
||
let mut found: BTreeMap<(u64, String), std::result::Result<Mat, String>> = BTreeMap::new();
|
||
let mut resolve = |o: &JointOrigin| -> Result<Mat> {
|
||
let Ok(comp) = component_of(doc, o.occurrence) else { return resolve_origin(doc, st, o) };
|
||
found
|
||
.entry((comp, format!("{:?}", o.snap)))
|
||
.or_insert_with(|| resolve_origin(doc, st, o).map_err(|e| e.to_string()))
|
||
.clone()
|
||
.map_err(DocError::Invalid)
|
||
};
|
||
let params = Params::new(doc);
|
||
for j in &joints {
|
||
// A joint whose expressions can't be worked out (a parameter gone) is left out rather
|
||
// than placed by numbers that no longer say what it was defined by.
|
||
if !j.exprs.is_empty()
|
||
&& let Err(e) = expressed(¶ms, j)
|
||
{
|
||
sol.errors.push((j.id, j.name.clone(), e.to_string()));
|
||
continue;
|
||
}
|
||
match (resolve(&j.a), resolve(&j.b)) {
|
||
(Ok(fa), Ok(fb)) => {
|
||
frames.insert(j.id, JointFrames::new(fa, fb));
|
||
}
|
||
(Err(e), _) | (_, Err(e)) => sol.errors.push((j.id, j.name.clone(), e.to_string())),
|
||
}
|
||
}
|
||
// Fixed: the root, grounded occurrences; with neither involved, the first joint's A side.
|
||
let mut placed: BTreeMap<u64, Mat> = BTreeMap::new();
|
||
let mut dof: BTreeMap<u64, usize> = BTreeMap::new();
|
||
placed.insert(0, IDENTITY);
|
||
dof.insert(0, 0);
|
||
for o in doc.occurrences.iter().filter(|o| o.grounded) {
|
||
placed.insert(o.id, occurrence_world(doc, o.id));
|
||
dof.insert(o.id, 0);
|
||
}
|
||
let involved: BTreeSet<u64> = joints.iter().flat_map(|j| [j.a.occurrence, j.b.occurrence]).collect();
|
||
if !involved.iter().any(|o| placed.contains_key(o))
|
||
&& let Some(j) = joints.first()
|
||
{
|
||
placed.insert(j.a.occurrence, occurrence_world(doc, j.a.occurrence));
|
||
dof.insert(j.a.occurrence, 0);
|
||
}
|
||
sol.fixed = placed.keys().copied().collect();
|
||
let mut tree =
|
||
// Every joint's values are known, suppressed ones too (their motion links still set values).
|
||
Tree { joints: asm.joints.iter().map(|j| (j.id, j)).collect(), frames, fixed: placed.clone(), parent: BTreeMap::new(), order: Vec::new() };
|
||
let mut used: BTreeSet<u64> = BTreeSet::new();
|
||
let mut queue: VecDeque<u64> = placed.keys().copied().collect();
|
||
// An occurrence's degrees of freedom are the distinct values that move it: those of the
|
||
// joints on its path, a value a motion link sets standing for the values its link chain
|
||
// starts from (a driven gear turns with its driving gear's one value). Kept per occurrence as
|
||
// a count of the values no link reads or sets, which no other path value can repeat, and the
|
||
// set of the ones that may be repeated (links' sources).
|
||
let sources = link_sources(asm);
|
||
let shared: BTreeSet<(u64, usize)> = sources.values().flatten().copied().collect();
|
||
let mut moved_by: BTreeMap<u64, (usize, BTreeSet<(u64, usize)>)> = BTreeMap::new();
|
||
// The joints at each occurrence, in the joints' order (a large assembly is not walked joint by
|
||
// joint for every occurrence).
|
||
let mut at: BTreeMap<u64, Vec<&Joint>> = BTreeMap::new();
|
||
for j in joints.iter().copied() {
|
||
at.entry(j.a.occurrence).or_default().push(j);
|
||
if j.b.occurrence != j.a.occurrence {
|
||
at.entry(j.b.occurrence).or_default().push(j);
|
||
}
|
||
}
|
||
while let Some(occ) = queue.pop_front() {
|
||
let Some(t) = placed.get(&occ).copied() else { continue };
|
||
for j in at.get(&occ).map(Vec::as_slice).unwrap_or_default() {
|
||
if used.contains(&j.id) || !tree.frames.contains_key(&j.id) {
|
||
continue;
|
||
}
|
||
let (other, from_a) = if j.a.occurrence == occ {
|
||
(j.b.occurrence, true)
|
||
} else if j.b.occurrence == occ {
|
||
(j.a.occurrence, false)
|
||
} else {
|
||
continue;
|
||
};
|
||
if placed.contains_key(&other) {
|
||
continue;
|
||
}
|
||
let Some(m) = tree.step(j.id, from_a, &t, vals) else { continue };
|
||
used.insert(j.id);
|
||
placed.insert(other, m);
|
||
tree.parent.insert(other, (occ, j.id, from_a));
|
||
tree.order.push(other);
|
||
let (mut own, mut common) = moved_by.get(&occ).cloned().unwrap_or_default();
|
||
for v in (0..j.kind.dofs().len()).map(|i| (j.id, i)) {
|
||
match sources.get(&v) {
|
||
Some(from) => common.extend(from.iter().copied()),
|
||
None if shared.contains(&v) => {
|
||
common.insert(v);
|
||
}
|
||
None => own += 1,
|
||
}
|
||
}
|
||
dof.insert(other, own + common.len());
|
||
moved_by.insert(other, (own, common));
|
||
queue.push_back(other);
|
||
}
|
||
}
|
||
// Joints that close loops: the solve moves the loops' values to meet them, then checks they
|
||
// agree.
|
||
let closing: Vec<u64> = joints
|
||
.iter()
|
||
.filter(|j| !used.contains(&j.id) && tree.frames.contains_key(&j.id))
|
||
.filter(|j| placed.contains_key(&j.a.occurrence) && placed.contains_key(&j.b.occurrence))
|
||
.map(|j| j.id)
|
||
.collect();
|
||
Built { tree, placed, closing, dof }
|
||
}
|
||
|
||
impl Document {
|
||
/// Apply a solution: occurrence transforms (in their parents) for the occurrences it places,
|
||
/// and the values of the joints that moved to close loops. Returns true when something moved.
|
||
pub fn apply_joint_solution(&mut self, sol: &Solution) -> bool {
|
||
// Joints and occurrences are indexed once (the first of each id, as a search finds):
|
||
// searching them for each of a large design's thousands of values and occurrences took
|
||
// 20 ms on every change to the design.
|
||
let mut joint_at = std::collections::HashMap::new();
|
||
for (i, j) in self.assembly.joints.iter().enumerate() {
|
||
joint_at.entry(j.id).or_insert(i);
|
||
}
|
||
let mut changed = false;
|
||
for (id, q) in &sol.values {
|
||
if let Some(j) = joint_at.get(id).and_then(|&i| self.assembly.joints.get_mut(i)) {
|
||
j.values.clone_from(q);
|
||
changed = true;
|
||
}
|
||
}
|
||
let parents: BTreeMap<u64, u64> = self.occurrences.iter().map(|o| (o.id, o.parent)).collect();
|
||
let (mut occurrence_at, mut first_of) = (std::collections::HashMap::new(), std::collections::HashMap::new());
|
||
for (i, o) in self.occurrences.iter().enumerate() {
|
||
occurrence_at.entry(o.id).or_insert(i);
|
||
first_of.entry(o.component).or_insert(i);
|
||
}
|
||
for (occ, world) in &sol.world {
|
||
let parent = parents.get(occ).copied().unwrap_or(0);
|
||
// Through the transforms as this loop has left them, as `component_transform` reads.
|
||
let occurrences = &self.occurrences;
|
||
let pw = if parent == 0 {
|
||
IDENTITY
|
||
} else {
|
||
crate::assembly::transform_through(parent, |c| first_of.get(&c).and_then(|&i| occurrences.get(i)))
|
||
};
|
||
let Some(local) = mat_inverse(&pw).map(|inv| mat_mul(&inv, world)) else { continue };
|
||
if let Some(o) = occurrence_at.get(occ).and_then(|&i| self.occurrences.get_mut(i)) {
|
||
let (dt, da) = mismatch(&o.transform, &local);
|
||
if dt > 1e-9 || da > 1e-10 {
|
||
o.transform = local;
|
||
changed = true;
|
||
}
|
||
}
|
||
}
|
||
changed
|
||
}
|
||
|
||
/// A frame for an as-built joint: the world frame `w` seen from an occurrence.
|
||
pub fn frame_in_occurrence(&self, occ: u64, w: &Mat) -> Option<Snap> {
|
||
let t = if occ == 0 { IDENTITY } else { occurrence_world(self, occ) };
|
||
let local = mat_mul(&mat_inverse(&t)?, w);
|
||
let o = apply_point(&local, Vec3::ZERO);
|
||
let z = apply_vector(&local, Vec3::Z);
|
||
let x = apply_vector(&local, Vec3::X);
|
||
Some(Snap::Frame { origin: o, z, x: Some(x) })
|
||
}
|
||
|
||
/// A joint origin's frame in the world (for as-built joints and display).
|
||
pub fn origin_world(&self, st: &ModelState, o: &JointOrigin) -> Result<Mat> {
|
||
let f = resolve_origin(self, st, o)?;
|
||
let t = if o.occurrence == 0 { IDENTITY } else { occurrence_world(self, o.occurrence) };
|
||
Ok(mat_mul(&t, &f))
|
||
}
|
||
}
|
||
|
||
#[path = "joints_cam.rs"]
|
||
pub mod cam;
|
||
|
||
#[path = "joints_edge.rs"]
|
||
mod edge;
|
||
pub use edge::{edge_axis, edge_snap};
|
||
|
||
#[path = "joints_reach.rs"]
|
||
mod reach;
|
||
|
||
#[path = "joints_face.rs"]
|
||
mod face;
|
||
pub use face::{end_faces, face_name_at, named_face_spot, pin_end, round_end_at};
|
||
#[path = "joints_relations.rs"]
|
||
mod relations;
|
||
pub use reach::{REACH_TOL, Reach, Reached, reach};
|
||
pub use relations::relation_values;
|
||
|
||
/// The rest angle that turns B least as joint `j` is made, as B sits now: none or a half turn
|
||
/// about the joint's z. Origins whose x is chosen for them (a face, a circle, a point without
|
||
/// x) get opposite x when their z are opposite, so two faces that already meet would, at angle
|
||
/// 0, spin B a half turn about their shared normal.
|
||
pub fn least_turn_angle(doc: &Document, st: &ModelState, j: &Joint) -> f64 {
|
||
let (Ok(fa), Ok(fb)) = (resolve_origin(doc, st, &j.a), resolve_origin(doc, st, &j.b)) else { return 0.0 };
|
||
let (ta, tb) = (occurrence_world(doc, j.a.occurrence), occurrence_world(doc, j.b.occurrence));
|
||
let mut q = j.values.clone();
|
||
q.resize(j.kind.dofs().len(), 0.0);
|
||
clamp(j, &mut q);
|
||
let turn = |angle: f64| {
|
||
let k = Joint { angle, ..j.clone() };
|
||
through(&k, &(fa, fb), &q, true, &ta).map(|m| mismatch(&m, &tb).1)
|
||
};
|
||
match (turn(0.0), turn(std::f64::consts::PI)) {
|
||
(Some(none), Some(half)) if half + 1e-9 < none => std::f64::consts::PI,
|
||
_ => 0.0,
|
||
}
|
||
}
|
||
|
||
/// The frame matrix for an explicit origin / z / x (public for commands).
|
||
pub fn frame_of(o: Vec3, z: Vec3, x: Option<Vec3>) -> Option<Mat> {
|
||
frame(o, z, x)
|
||
}
|
||
|
||
#[cfg(test)]
|
||
mod tests {
|
||
use super::*;
|
||
|
||
thread_local! {
|
||
pub(super) static PLACEMENT_STEPS: std::cell::Cell<usize> = const { std::cell::Cell::new(0) };
|
||
pub(super) static PLACEMENT_INSERTS: std::cell::Cell<usize> = const { std::cell::Cell::new(0) };
|
||
}
|
||
|
||
pub(super) fn placement_tree(asm: &Assembly) -> Tree<'_> {
|
||
Tree {
|
||
joints: asm.joints.iter().map(|j| (j.id, j)).collect(),
|
||
frames: asm.joints.iter().map(|j| (j.id, JointFrames::new(mat_mul(&shift(3.0, 4.0, 5.0), &rot_y(0.3)), rot_x(-0.2)))).collect(),
|
||
fixed: BTreeMap::from([(0, IDENTITY)]),
|
||
parent: BTreeMap::from([(1, (0, 1, true)), (2, (1, 2, false)), (3, (2, 3, true)), (4, (1, 4, true)), (99, (0, 5, true))]),
|
||
order: vec![1, 2, 3, 4, 99],
|
||
}
|
||
}
|
||
|
||
/// Shared ancestors are evaluated once, without visiting an unrelated assembly branch.
|
||
/// The same arithmetic must be used after values change and on a reversed tree edge.
|
||
#[test]
|
||
fn residual_placements_reuse_ancestors_only_for_the_current_values() {
|
||
let asm = chain(6, 0.2);
|
||
let tree = placement_tree(&asm);
|
||
let mut values = joint_values(&asm);
|
||
let expected: BTreeMap<u64, Mat> = [1, 2, 3, 4].into_iter().map(|id| (id, tree.world(id, &values).unwrap())).collect();
|
||
let mut workspace = PlacementWorkspace::new(&tree);
|
||
PLACEMENT_STEPS.with(|steps| steps.set(0));
|
||
{
|
||
let mut placed = workspace.at(&values);
|
||
for id in [3, 4, 3, 2, 4] {
|
||
assert_eq!(placed.world(id), expected.get(&id).copied());
|
||
}
|
||
assert_eq!(placed.world(0), Some(IDENTITY));
|
||
assert_eq!(placed.world(1234), None);
|
||
}
|
||
assert_eq!(PLACEMENT_STEPS.with(|steps| steps.get()), 4, "one step per needed occurrence; no unrelated branch");
|
||
values.get_mut(&1).unwrap()[0] += 0.1;
|
||
apply_links(&asm, &mut values);
|
||
let changed = tree.world(3, &values).unwrap();
|
||
assert_ne!(Some(&changed), expected.get(&3));
|
||
let mut placed = workspace.at(&values);
|
||
assert_eq!(placed.world(3), Some(changed), "a new residual evaluation cannot reuse the previous values' placements");
|
||
}
|
||
|
||
/// Cached static inverses retain the original multiplication order for every joint kind,
|
||
/// flip and traversal direction. A non-invertible frame remains a failed step.
|
||
#[test]
|
||
fn prepared_joint_frames_match_fresh_inverses() {
|
||
fn reference(j: &Joint, fa: &Mat, fb: &Mat, q: &[f64], from_a: bool, t: &Mat) -> Option<Mat> {
|
||
let link = mat_mul(&link_of(j, q), &mat_inverse(fb)?);
|
||
if from_a { Some(mat_mul(&mat_mul(t, fa), &link)) } else { Some(mat_mul(&mat_mul(t, &mat_inverse(&link)?), &mat_inverse(fa)?)) }
|
||
}
|
||
let mut joint = chain(1, 0.0).joints.remove(0);
|
||
let fa = mat_mul(&shift(3.0, -7.0, 11.0), &rot_y(0.3));
|
||
let fb = mat_mul(&shift(-2.0, 5.0, 13.0), &rot_x(-0.2));
|
||
let t = mat_mul(&shift(17.0, 19.0, -23.0), &rot_z(0.7));
|
||
let singular = [[0.0; 4]; 4];
|
||
for (a, b) in [(fa, fb), (singular, fb), (fa, singular)] {
|
||
let frames = JointFrames::new(a, b);
|
||
for kind in [
|
||
JointKind::Rigid,
|
||
JointKind::Revolute,
|
||
JointKind::Slider,
|
||
JointKind::Cylindrical,
|
||
JointKind::PinSlot,
|
||
JointKind::Planar,
|
||
JointKind::Ball,
|
||
JointKind::Parallel,
|
||
JointKind::Perpendicular,
|
||
JointKind::Angle,
|
||
JointKind::PointOnPlane,
|
||
JointKind::PointOnLine,
|
||
JointKind::LineOnPlane,
|
||
] {
|
||
joint.kind = kind;
|
||
joint.offset = 2.7;
|
||
joint.angle = -0.41;
|
||
for flip in [false, true] {
|
||
joint.flip = flip;
|
||
for angle in [0.0, 1e-6, -0.37, std::f64::consts::PI] {
|
||
let q: Vec<f64> = (0..kind.dofs().len()).map(|i| angle * (i + 1) as f64).collect();
|
||
for forward in [false, true] {
|
||
assert_eq!(
|
||
frames.through(&joint, &q, forward, &t),
|
||
reference(&joint, &a, &b, &q, forward, &t),
|
||
"{kind:?}, {flip}, {angle}, {forward}"
|
||
);
|
||
}
|
||
}
|
||
}
|
||
}
|
||
}
|
||
}
|
||
|
||
/// The loop solver's residual entry point reuses shared ancestors for each perturbation;
|
||
/// row order, duplicate rows, append semantics and missing-origin failure stay unchanged.
|
||
#[test]
|
||
fn closure_residuals_reuse_shared_ancestors_for_each_perturbation() {
|
||
let mut asm = chain(6, 0.2);
|
||
asm.joints[5].a.occurrence = 3;
|
||
asm.joints[5].b.occurrence = 4;
|
||
let tree = placement_tree(&asm);
|
||
let mut workspace = PlacementWorkspace::new(&tree);
|
||
let mut cold = true;
|
||
for start in [0.2, 0.2 + 1e-6, 0.2 - 1e-6, 1.3] {
|
||
let mut values = joint_values(&asm);
|
||
values.get_mut(&1).unwrap()[0] = start;
|
||
apply_links(&asm, &mut values);
|
||
let mut expected = vec![42.0];
|
||
for id in [6, 6] {
|
||
let joint = tree.joints.get(&id).unwrap();
|
||
let frames = tree.frames.get(&id).unwrap();
|
||
let a = tree.world(joint.a.occurrence, &values).unwrap();
|
||
let b = tree.world(joint.b.occurrence, &values).unwrap();
|
||
let want = through(joint, &(frames.a, frames.b), values.get(&id).unwrap(), true, &a).unwrap();
|
||
for point in [Vec3::ZERO, Vec3::X * 37.0, Vec3::Y * 37.0] {
|
||
let at = apply_point(&frames.b, point);
|
||
let d = apply_point(&want, at) - apply_point(&b, at);
|
||
expected.extend([d.x, d.y, d.z]);
|
||
}
|
||
}
|
||
PLACEMENT_STEPS.with(|steps| steps.set(0));
|
||
PLACEMENT_INSERTS.with(|inserts| inserts.set(0));
|
||
let mut actual = vec![42.0];
|
||
assert_eq!(closure_gaps(&mut workspace, &[6, 6], &values, 37.0, &mut actual), Some(()));
|
||
assert_eq!(actual, expected);
|
||
assert_eq!(PLACEMENT_INSERTS.with(|inserts| inserts.get()), if cold { 4 } else { 0 }, "reuse cache storage between perturbations");
|
||
cold = false;
|
||
assert_eq!(PLACEMENT_STEPS.with(|steps| steps.get()), 6, "four tree placements and two closing-joint steps");
|
||
assert_eq!(closure_gaps(&mut workspace, &[u64::MAX], &values, 37.0, &mut actual), None);
|
||
assert_eq!(actual, expected, "an unresolved joint does not insert a zero residual");
|
||
}
|
||
}
|
||
|
||
/// The parameter values kept between expressions give what evaluating each expression on
|
||
/// its own gives, errors included.
|
||
#[test]
|
||
fn kept_parameters_evaluate_as_the_design_does() {
|
||
let mut doc = Document::new("p");
|
||
doc.set_param("W", "300 mm", None, None).unwrap();
|
||
doc.set_param("H", "W / 2", None, None).unwrap();
|
||
doc.set_param("A", "30 deg", None, None).unwrap();
|
||
let params = Params::new(&doc);
|
||
for (e, kind) in [
|
||
("W / 4", crate::expr::Kind::Length),
|
||
("H + 2 mm", crate::expr::Kind::Length),
|
||
("A * 2", crate::expr::Kind::Angle),
|
||
("12", crate::expr::Kind::Length),
|
||
] {
|
||
assert_eq!(params.eval(e, kind).unwrap(), doc.eval(e, kind).unwrap(), "{e}");
|
||
}
|
||
for (e, kind) in [("Q + 1", crate::expr::Kind::Length), ("A", crate::expr::Kind::Length)] {
|
||
assert_eq!(params.eval(e, kind).unwrap_err().to_string(), doc.eval(e, kind).unwrap_err().to_string(), "{e}");
|
||
}
|
||
}
|
||
|
||
fn close(a: &Mat, b: &Mat) -> bool {
|
||
let (t, r) = mismatch(a, b);
|
||
t < 1e-9 && r < 1e-9
|
||
}
|
||
|
||
/// Revolute joints 1…n (joint 1 at `start`, the others at 0) linked 1 → 2 → … → n with
|
||
/// ratio 2, the links stored from the end of the chain; joint 3 limited to ±50.
|
||
pub(super) fn chain(n: u64, start: f64) -> Assembly {
|
||
let origin = JointOrigin { occurrence: 0, snap: Snap::Point { point: Vec3::ZERO, z: None, x: None } };
|
||
let joints = (1..=n)
|
||
.map(|id| Joint {
|
||
id,
|
||
name: format!("J{id}"),
|
||
kind: JointKind::Revolute,
|
||
a: origin.clone(),
|
||
b: origin.clone(),
|
||
values: vec![if id == 1 { start } else { 0.0 }],
|
||
limits: vec![(id == 3).then_some((-50.0, 50.0))],
|
||
flip: false,
|
||
offset: 0.0,
|
||
angle: 0.0,
|
||
suppressed: false,
|
||
exprs: Default::default(),
|
||
})
|
||
.collect();
|
||
let links =
|
||
(1..n).rev().map(|a| MotionLink { a, ia: 0, b: a + 1, ib: 0, ratio: 2.0, offset: 0.0, coupling: None, lift: Vec::new() }).collect();
|
||
Assembly { joints, links, ..Assembly::default() }
|
||
}
|
||
|
||
/// A linked value moves with the free value its chain starts from, however the chain is
|
||
/// stored; a chain that comes back round on itself, or a link from a value its joint lacks
|
||
/// (hand-edited designs), moves it with nothing.
|
||
#[test]
|
||
fn linked_values_move_with_their_chains_start() {
|
||
let mut asm = chain(5, 0.0);
|
||
let sources = link_sources(&asm);
|
||
for b in 2..=5 {
|
||
assert_eq!(sources.get(&(b, 0)), Some(&BTreeSet::from([(1, 0)])), "J{b}: {sources:?}");
|
||
}
|
||
assert!(!sources.contains_key(&(1, 0)));
|
||
let link = |a: u64, ia: usize, b: u64| MotionLink { a, ia, b, ib: 0, ratio: 1.0, offset: 0.0, coupling: None, lift: Vec::new() };
|
||
asm.links.push(link(5, 0, 1));
|
||
assert!(link_sources(&asm).values().all(BTreeSet::is_empty), "{:?}", link_sources(&asm));
|
||
let mut asm = chain(2, 0.0);
|
||
asm.links = vec![link(1, 7, 2)];
|
||
assert_eq!(link_sources(&asm).get(&(2, 0)), Some(&BTreeSet::new()));
|
||
assert!(link_sources(&Assembly::default()).is_empty());
|
||
}
|
||
|
||
/// Links carry a value down a chain stored from its end, each linked value within its limits
|
||
/// as it is set, and applying them again changes nothing.
|
||
#[test]
|
||
fn links_settle_whatever_order_they_are_stored_in() {
|
||
let asm = chain(8, 10.0);
|
||
let vals = joint_values(&asm);
|
||
let at = |id: u64| vals.get(&id).and_then(|q| q.first()).copied().unwrap_or(f64::NAN);
|
||
// 10 → 20 → 40 (within joint 3's limit) → 80 → … → 1280.
|
||
assert_eq!((at(1), at(2), at(3), at(4), at(8)), (10.0, 20.0, 40.0, 80.0, 1280.0));
|
||
let asm = chain(8, 40.0);
|
||
let vals = joint_values(&asm);
|
||
let at = |id: u64| vals.get(&id).and_then(|q| q.first()).copied().unwrap_or(f64::NAN);
|
||
// Joint 3 would be 160: held at 50, and what follows it follows the 50.
|
||
assert_eq!((at(3), at(4), at(8)), (50.0, 100.0, 1600.0));
|
||
let mut again = vals.clone();
|
||
apply_links(&asm, &mut again);
|
||
assert_eq!(again, vals);
|
||
}
|
||
|
||
/// A coupling saves as its definition: sizes as numbers, expressions or picked faces, flags
|
||
/// only when set; a link without one (as every design before couplings has) reads as before.
|
||
#[test]
|
||
fn couplings_read_and_write_their_definition() {
|
||
let old: MotionLink = serde_json::from_str(r#"{"a": 1, "b": 2, "ratio": 2}"#).unwrap();
|
||
assert_eq!((old.coupling, old.offset, old.ia), (None, 0.0, 0));
|
||
let text = r#"{"a": 1, "b": 2, "ratio": -0.5, "coupling": {"type": "gear", "ra": 10, "rb": "r2 * 2",
|
||
"internal": true}}"#;
|
||
let l: MotionLink = serde_json::from_str(text).unwrap();
|
||
let Some(Coupling::Gear { ra, rb, internal, reverse }) = &l.coupling else { panic!("{l:?}") };
|
||
assert_eq!((ra, rb, *internal, *reverse), (&Size::Length(10.0), &Size::Expr("r2 * 2".into()), true, false));
|
||
let back = serde_json::to_value(&l).unwrap();
|
||
assert_eq!(back["coupling"], serde_json::json!({"type": "gear", "ra": 10.0, "rb": "r2 * 2", "internal": true}));
|
||
let picked: Size = serde_json::from_str(r#"{"occurrence": 3, "snap": {"type": "circle_center", "pick": [1, 0, 0]}}"#).unwrap();
|
||
assert!(matches!(picked, Size::Circle(JointOrigin { occurrence: 3, snap: Snap::CircleCenter { .. } })));
|
||
let screw: Coupling = serde_json::from_str(r#"{"type": "screw", "pitch": 1.5, "reverse": true}"#).unwrap();
|
||
assert_eq!(screw, Coupling::Screw { pitch: Size::Length(1.5), reverse: true });
|
||
}
|
||
|
||
/// Ratios from the sizes: gears turn by their radii (the other way unless internal), a rack
|
||
/// and a screw travel per radian whichever of the two joints drives.
|
||
#[test]
|
||
fn coupling_ratios_follow_their_sizes() {
|
||
let mut doc = Document { assembly: chain(3, 0.0), ..Document::default() };
|
||
if let Some(j) = doc.assembly.joints.get_mut(2) {
|
||
j.kind = JointKind::Slider;
|
||
}
|
||
let st = ModelState::default();
|
||
let ratio = |a: u64, b: u64, c: Coupling| {
|
||
let l = MotionLink { a, ia: 0, b, ib: 0, ratio: 0.0, offset: 0.0, coupling: Some(c), lift: Vec::new() };
|
||
coupling_values(&doc, &st, &l).map(|r| r.map(|(ratio, _)| ratio).map_err(|e| e.to_string()))
|
||
};
|
||
let len = Size::Length;
|
||
assert_eq!(ratio(1, 2, Coupling::Gear { ra: len(10.0), rb: len(40.0), internal: false, reverse: false }), Some(Ok(-0.25)));
|
||
assert_eq!(ratio(1, 2, Coupling::Gear { ra: len(10.0), rb: len(40.0), internal: true, reverse: false }), Some(Ok(0.25)));
|
||
assert_eq!(ratio(1, 3, Coupling::RackPinion { radius: len(8.0), reverse: false }), Some(Ok(8.0)));
|
||
assert_eq!(ratio(3, 1, Coupling::RackPinion { radius: len(8.0), reverse: true }), Some(Ok(-0.125)));
|
||
let screw = ratio(1, 3, Coupling::Screw { pitch: len(std::f64::consts::TAU), reverse: false });
|
||
assert_eq!(screw, Some(Ok(1.0)));
|
||
assert!(matches!(ratio(1, 2, Coupling::RackPinion { radius: len(8.0), reverse: false }), Some(Err(_))));
|
||
assert!(matches!(ratio(1, 3, Coupling::Gear { ra: len(1.0), rb: len(1.0), internal: false, reverse: false }), Some(Err(_))));
|
||
for bad in [0.0, -2.0, f64::NAN, f64::INFINITY, 1e300] {
|
||
assert!(matches!(ratio(1, 2, Coupling::Gear { ra: len(bad), rb: len(1.0), internal: false, reverse: false }), Some(Err(_))), "{bad}");
|
||
}
|
||
assert!(matches!(ratio(1, 2, Coupling::Gear { ra: Size::Expr("nope".into()), rb: len(1.0), internal: false, reverse: false }), Some(Err(_))));
|
||
}
|
||
|
||
#[test]
|
||
fn motions_compose() {
|
||
assert!(close(&motion(JointKind::Revolute, &[std::f64::consts::FRAC_PI_2]), &rot_z(std::f64::consts::FRAC_PI_2)));
|
||
let m = motion(JointKind::Cylindrical, &[0.0, 5.0]);
|
||
assert!((m[3][2] - 5.0).abs() < 1e-12);
|
||
let m = motion(JointKind::PinSlot, &[0.0, 3.0]);
|
||
assert!((m[3][0] - 3.0).abs() < 1e-12);
|
||
assert_eq!(JointKind::Ball.dofs().len(), 3);
|
||
assert!(JointKind::parse("Pin Slot").is_some() && JointKind::parse("nope").is_none());
|
||
let f = frame(Vec3::new(1.0, 2.0, 3.0), Vec3::Z, None).unwrap();
|
||
assert!(close(&mat_mul(&f, &mat_inverse(&f).unwrap()), &IDENTITY));
|
||
}
|
||
|
||
#[test]
|
||
fn mismatch_resolves_tiny_turns() {
|
||
let (_, a) = mismatch(&rot_z(1e-9), &IDENTITY);
|
||
assert!((a - 1e-9).abs() < 1e-15, "{a}");
|
||
let (_, a) = mismatch(&rot_z(3.0), &IDENTITY);
|
||
assert!((a - 3.0).abs() < 1e-12, "{a}");
|
||
}
|
||
|
||
/// Applying a solution stores each occurrence in its parent's frame as the loop has left it:
|
||
/// a component the same solution moves is read moved, through its first occurrence. Joint
|
||
/// values land on their joints; a value for a missing joint is skipped.
|
||
#[test]
|
||
fn a_solution_places_occurrences_in_their_moved_parents() {
|
||
let occurrence =
|
||
|id, component, parent| crate::Occurrence { id, component, parent, name: format!("O{id}"), transform: IDENTITY, grounded: false };
|
||
// Component 1 sits at the root twice (its first occurrence is the frame its children sit
|
||
// in), component 2 inside 1 and component 3 inside 2.
|
||
let mut doc = Document {
|
||
assembly: chain(2, 0.0),
|
||
occurrences: vec![occurrence(10, 1, 0), occurrence(11, 1, 0), occurrence(20, 2, 1), occurrence(30, 3, 2)],
|
||
..Document::default()
|
||
};
|
||
let w10 = mat_mul(&shift(3.0, 4.0, 5.0), &rot_y(0.3));
|
||
let w20 = mat_mul(&shift(-1.0, 2.0, 0.5), &rot_x(-0.2));
|
||
let w30 = mat_mul(&shift(0.0, 7.0, 1.0), &rot_y(1.1));
|
||
let world = BTreeMap::from([(10, w10), (20, w20), (30, w30)]);
|
||
let sol = Solution { world: world.clone(), values: BTreeMap::from([(2, vec![0.75]), (99, vec![1.0])]), ..Solution::default() };
|
||
assert!(doc.apply_joint_solution(&sol));
|
||
for (component, w) in [(1, w10), (2, w20), (3, w30)] {
|
||
assert!(close(&doc.component_transform(component), &w), "component {component}");
|
||
}
|
||
assert!(close(&doc.occurrences[1].transform, &IDENTITY), "only the occurrence the solution names moves");
|
||
let values: Vec<_> = doc.assembly.joints.iter().map(|j| j.values.clone()).collect();
|
||
assert_eq!(values, vec![vec![0.0], vec![0.75]]);
|
||
assert!(!doc.apply_joint_solution(&Solution { world, ..Solution::default() }), "applied twice, nothing moves");
|
||
}
|
||
}
|