Files
solidcraft/tests/kernel-cases/fillets/KNOWN_FAILING
T
jyvikoandClaude Opus 5.5 7953944175 Fillet rig: 1668's R7 past the inside corner is refused at 4 + 2 sqrt2
The round's centre (32 - r, 42 - r) leaves the hollow's corner (30, 40)
outside its circle, opening the wall, where sqrt2 (r - 2) = r: the case
expects the refusal naming 6.828. 2852's R30, refused naming 25.24, now
passes too: both come off the known-failing list.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 22:19:55 -04:00

24 lines
3.0 KiB
Plaintext

# The fillet cases that fail today, one a line: `<case> <why it fails today>`. Sorted. The fillet
# rig gate (.github/workflows/fillet-rig.yml) fails on a case that fails and is not listed here,
# and on a listed case that passes: a fix removes its line in the same pull request.
# Baseline: develop 242bbc89f with the SMLib fixes of 2026-10-29 (integration-overnight + b78bd4a), aarch64 Linux.
1080-fillet-equal-slope-basin-1-mm-rim-loop-4 not supported yet: a convex round past its face is not yet built by subtraction
1080-fillet-sloped-basin-0-5-mm-rim-r4-4-edges not supported yet: a convex round past its face is not yet built by subtraction
1080-fillet-sloped-basin-1-mm-rim-r4-2-edges not supported yet: a convex round past its face is not yet built by subtraction
1080-fillet-sloped-basin-1-mm-rim-r4-4-edges not supported yet: a convex round past its face is not yet built by subtraction
1207-fillet-bar-top-edge-after-boss-arc-round-r0-5 SMLib's check refuses the round: internal coincident control points in a B-spline curve (an internal pole)
190-fillet-disc-rim-past-its-2mm-wall SMLib status 1001: a convex round past its face is not yet built by subtraction
2893-chamfer-distance-and-angle-past-the-wall-refused refused for another reason: SMLib SM_ERR_INVALID_INPUT, not a check saying the angle runs past the wall
2893-chamfer-two-distances-elliptical-rim SMLib status 1001 on the elliptical rim's chamfer
2893-chamfer-two-distances-past-the-bottom SMLib status 1001: SmFilletNx1ClosedCorner cannot compute the closed rim's corner geometry, where the chamfer past the bottom rim should build the frustum
4782-fillet-bar-edge-wider-than-both-faces SMLib status 1001: a convex round past both its faces is not yet built by subtraction
5158-fillet-round-just-past-a-10mm-face SMLib status 1001: a convex round 0.01 past its face is not yet built by subtraction (10.0001-10.04 open)
9-fillet-corner-curvature-with-reduce-fit not supported yet: solid.fillet builds corner g2 with the exact fit only
9-fillet-corner-curvature-with-taper-fit not supported yet: solid.fillet builds corner g2 with the exact fit only
926-chamfer-top-edge-ending-on-boss-wall-above-it not supported yet: the chamfer is refused as larger than its faces where it ends on the boss's wall
cov-chamfer-concave-edge-through-up-down-joined-squares SMLib status 1001 on the concave chamfer's tangent chain
cov-chamfer-outer-corner-edge-of-a-shelled-box-with-a-lip SMLib's chamfer result is not a closed solid where it ends on the lip
cov-fillet-arc-edge-on-an-oblique-cut-of-a-bar SMLib's check refuses the round: internal coincident control points in a B-spline curve
every-block-cylinder-crease-top-edge-after-arc-round-r1 the r1 round's contact seam with the block's side face reads 60 degrees (the cylinder wall's normal) at its end on the crease (8.660, 5, 15.284): G0 where the round is built tangent
every-hole-top-rim-r12-past-plate-bottom SMLib status 1001: a convex round past its face on the tangent side is not yet built by subtraction