The thread forms (b4549d270) parse designations in thread_forms, whose refusal for a plain
M28 said "give it: M28x1" and, for M0 or M1e9, still offered a pitch. The hint the hole
command gave (the two coarsest ISO fine pitches that suit the diameter: M28x2 or M28x1.5) is
now thread_forms::no_coarse_pitch, used by both; a diameter no metric thread has is an
unknown metric thread. The test's "unknown thread" follows the forms' wording ("unknown
metric thread").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
1271 lines
70 KiB
Rust
1271 lines
70 KiB
Rust
//! Modelled threads: the ISO metric profile cut along a helix, inside and outside,
|
||
//! including fine pitches on large shafts and the sample flange.
|
||
|
||
use std::f64::consts::PI;
|
||
|
||
use serde_json::{Value, json};
|
||
use solidcraft_geom::Vec3;
|
||
|
||
use crate::Session;
|
||
|
||
fn run(s: &mut Session, id: &str, p: Value) -> Value {
|
||
match s.execute(id, &p) {
|
||
Ok(v) => v,
|
||
Err(e) => panic!("{id} {p}: {e}"),
|
||
}
|
||
}
|
||
|
||
/// Volume from the body's mesh: exact for the faceted threaded body, and quicker than a full
|
||
/// measurement of its thousands of faces.
|
||
fn volume(s: &mut Session, b: &str) -> f64 {
|
||
let st = s.model.state();
|
||
st.body(b).map(|mb| mb.body.mesh(&solidcraft_kernel::MeshTolerance::chord(1e-3)).unwrap().measure().volume).unwrap_or(0.0)
|
||
}
|
||
|
||
const SIZES: [(f64, f64); 9] = [(3.0, 0.5), (4.0, 0.7), (5.0, 0.8), (6.0, 1.0), (8.0, 1.25), (10.0, 1.5), (12.0, 1.75), (16.0, 2.0), (20.0, 2.5)];
|
||
|
||
fn assert_tapped_depth(state: &solidcraft_doc::ModelState, entry: Vec3, inward: Vec3, offset: f64, depth: f64) {
|
||
assert_eq!(state.threads.len(), 1);
|
||
let thread = &state.threads[0];
|
||
assert!(thread.internal);
|
||
let a = (thread.axis_point + thread.axis * thread.start - entry).dot(inward);
|
||
let b = (thread.axis_point + thread.axis * thread.end - entry).dot(inward);
|
||
assert!((a.min(b) - offset).abs() < 1e-6, "thread entry {} mm, expected {offset} mm", a.min(b));
|
||
assert!((a.max(b) - offset - depth).abs() < 1e-6, "thread end {} mm, expected {} mm", a.max(b), offset + depth);
|
||
}
|
||
|
||
#[test]
|
||
fn tapped_thread_depth_keeps_reference_edge_placement_after_reopen() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length":60,"width":60,"height":12}));
|
||
run(
|
||
&mut s,
|
||
"solid.hole",
|
||
json!({"position":[30,30,12],"thread":"M6","depth":8,"thread_depth":3,
|
||
"references":[{"edge":[0,25,12],"distance":"10 mm"},{"edge":[25,0,12],"distance":"12 mm"}]}),
|
||
);
|
||
let inward = Vec3::new(0.0, 0.0, -1.0);
|
||
let entry = Vec3::new(10.0, 12.0, 12.0);
|
||
assert_tapped_depth(&s.model.state(), entry, inward, 0.0, 3.0);
|
||
let reopened = Session::new(solidcraft_doc::Document::from_json(&s.doc.to_json()).unwrap());
|
||
assert_tapped_depth(&reopened.model.state(), entry, inward, 0.0, 3.0);
|
||
let solidcraft_doc::FeatureKind::Hole { references, thread_depth, .. } = &reopened.doc.features.last().unwrap().kind else {
|
||
panic!("expected a referenced tapped hole");
|
||
};
|
||
assert_eq!(references.len(), 2);
|
||
assert_eq!(thread_depth.as_ref().unwrap().to_string(), "3");
|
||
assert!(!reopened.model.state().bodies[0].body.contains(Vec3::new(10.0, 12.0, 10.0)));
|
||
}
|
||
|
||
#[test]
|
||
fn tapped_thread_depth_is_independent_through_preview_redefine_undo_and_reload() {
|
||
for (height, mut params, full) in
|
||
[(12.0, json!({"depth":8,"type":"drilled"}), 8.0), (12.0, json!({}), 12.0), (12.0, json!({"to":[30,30,5]}), 7.0)]
|
||
{
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length":60,"width":60,"height":height,"body_name":"Plate"}));
|
||
params["position"] = json!([30, 30, height]);
|
||
params["direction"] = json!([0, 0, -1]);
|
||
params["thread"] = json!("M6");
|
||
let hole = run(&mut s, "solid.hole", params.clone())["feature"].as_u64().unwrap();
|
||
let entry = Vec3::new(30.0, 30.0, height);
|
||
let inward = Vec3::new(0.0, 0.0, -1.0);
|
||
assert_tapped_depth(&s.model.state(), entry, inward, 0.0, full);
|
||
let before = s.doc.to_json();
|
||
let physical_volume = volume(&mut s, "Plate");
|
||
|
||
// Version 29 never saved this field: its default remains the full wall.
|
||
let mut legacy: Value = serde_json::from_str(&before).unwrap();
|
||
legacy["format"] = json!("solidcraft/29");
|
||
let reopened = Session::new(solidcraft_doc::Document::from_json(&legacy.to_string()).unwrap());
|
||
assert_tapped_depth(&reopened.model.state(), entry, inward, 0.0, full);
|
||
|
||
params["thread_depth"] = json!(4);
|
||
let redefine = json!({"feature":hole,"command":"solid.hole","params":params});
|
||
let preview = s.preview(&[("timeline.redefine".into(), redefine.clone())]).unwrap();
|
||
assert_tapped_depth(&preview.after, entry, inward, 0.0, 4.0);
|
||
assert_eq!(s.doc.to_json(), before, "preview must not change the design");
|
||
run(&mut s, "timeline.redefine", redefine);
|
||
assert_tapped_depth(&s.model.state(), entry, inward, 0.0, 4.0);
|
||
assert!((volume(&mut s, "Plate") - physical_volume).abs() < 1e-6, "thread depth must not change the drill geometry");
|
||
let saved = s.doc.to_json();
|
||
let reopened = Session::new(solidcraft_doc::Document::from_json(&saved).unwrap());
|
||
assert_tapped_depth(&reopened.model.state(), entry, inward, 0.0, 4.0);
|
||
run(&mut s, "edit.undo", json!({}));
|
||
assert_eq!(s.doc.to_json(), before);
|
||
assert_tapped_depth(&s.model.state(), entry, inward, 0.0, full);
|
||
}
|
||
}
|
||
|
||
#[test]
|
||
fn tapped_thread_depth_uses_the_cylinder_beyond_recesses_and_in_shallow_holes() {
|
||
for (height, mut params, offset, full) in [
|
||
(12.0, json!({"thread":"M6","type":"counterbore","cb_diameter":12,"cb_depth":5,"depth":9}), 5.0, 4.0),
|
||
(12.0, json!({"thread":"G 1/4","type":"counterbore","cb_diameter":20,"cb_depth":5,"depth":9}), 5.0, 4.0),
|
||
(12.0, json!({"thread":"1/4-20 UNC","type":"counterbore","cb_diameter":12,"cb_depth":5,"depth":9}), 5.0, 4.0),
|
||
(12.0, json!({"thread":"M6","type":"countersink","cs_diameter":11,"cs_angle":"90 deg","depth":9}), 3.0, 6.0),
|
||
(12.0, json!({"thread":"M36","type":"drilled","depth":3}), 0.0, 3.0),
|
||
(5.0, json!({"thread":"M36"}), 0.0, 5.0),
|
||
] {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length":60,"width":60,"height":height,"body_name":"Plate"}));
|
||
params["position"] = json!([30, 30, height]);
|
||
params["direction"] = json!([0, 0, -1]);
|
||
let hole = run(&mut s, "solid.hole", params.clone())["feature"].as_u64().unwrap();
|
||
let entry = Vec3::new(30.0, 30.0, height);
|
||
let inward = Vec3::new(0.0, 0.0, -1.0);
|
||
assert_tapped_depth(&s.model.state(), entry, inward, offset, full);
|
||
params["thread_depth"] = json!(2);
|
||
run(&mut s, "timeline.redefine", json!({"feature":hole,"command":"solid.hole","params":params}));
|
||
assert_tapped_depth(&s.model.state(), entry, inward, offset, 2.0);
|
||
}
|
||
}
|
||
|
||
#[test]
|
||
fn tapped_thread_depth_starts_at_the_entry_for_both_axis_directions() {
|
||
for (entry, inward) in [(Vec3::new(0.0, 10.0, 6.0), Vec3::new(1.0, 0.0, 0.0)), (Vec3::new(20.0, 10.0, 6.0), Vec3::new(-1.0, 0.0, 0.0))] {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length":20,"width":20,"height":12}));
|
||
run(
|
||
&mut s,
|
||
"solid.hole",
|
||
json!({"position":[entry.x,entry.y,entry.z],"direction":[inward.x,inward.y,inward.z],"thread":"M6","depth":8,"thread_depth":3}),
|
||
);
|
||
assert_tapped_depth(&s.model.state(), entry, inward, 0.0, 3.0);
|
||
}
|
||
}
|
||
|
||
#[test]
|
||
fn tapped_thread_depth_rejects_invalid_or_excessive_values_atomically() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length":20,"width":20,"height":10}));
|
||
let before = s.doc.to_json();
|
||
for depth in [json!(0), json!(-1), json!(20), json!(true), json!(""), json!("NaN mm"), json!("1e999 mm"), json!("3 deg")] {
|
||
let result = s.execute("solid.hole", &json!({"position":[10,10,10],"thread":"M6","depth":8,"thread_depth":depth}));
|
||
assert!(result.is_err(), "invalid thread depth {depth}: {result:?}");
|
||
assert_eq!(s.doc.to_json(), before);
|
||
assert!(s.model.state().threads.is_empty());
|
||
}
|
||
assert!(s.execute("solid.hole", &json!({"position":[10,10,10],"diameter":5,"thread_depth":3})).is_err());
|
||
assert_eq!(s.doc.to_json(), before);
|
||
}
|
||
|
||
/// Keep the original 48-station reproduction of the shell error even though new fine
|
||
/// threads now use more stations. The same cut polygons must rebuild as a closed solid.
|
||
#[test]
|
||
fn faceted_flange_thread_preserves_thin_crest_boundaries() {
|
||
use crate::geom::{Plane, Vec2, Vec3};
|
||
use crate::kernel;
|
||
|
||
let mut s = Session::default();
|
||
let sample = crate::sample::samples().into_iter().find(|s| s.name == "Bolted Flange").unwrap();
|
||
s.run_script(&(sample.script)()).unwrap();
|
||
let state = s.model.state();
|
||
let body = &state.body("Flange").unwrap().body;
|
||
let face = Vec3::new(-19.034766861657907, -11.03075929038123, 19.574640342897094);
|
||
let cylinder = kernel::cylinder_face_at(body, face).unwrap();
|
||
let pitch = 1.5;
|
||
let height = pitch * 3f64.sqrt() / 2.0;
|
||
let root = 22.0 - 5.0 * height / 8.0;
|
||
let outer = 22.0 + 0.05 * pitch;
|
||
let half_width = (pitch / 4.0 + 2.0 * (outer - root) * (PI / 6.0).tan()) / 2.0;
|
||
let section = [Vec2::new(root, -pitch / 8.0), Vec2::new(outer, -half_width), Vec2::new(outer, half_width), Vec2::new(root, pitch / 8.0)];
|
||
let (start, end) = (cylinder.start - pitch, cylinder.end + pitch);
|
||
let base = cylinder.axis_point + cylinder.axis * start;
|
||
let plane = Plane { origin: base, x: cylinder.axis.cross(Vec3::new(1.0, 0.0, 0.0)).normalized().unwrap(), y: *cylinder.axis };
|
||
let groove = kernel::sweep_helix_mesh(&plane, §ion, base, *cylinder.axis, pitch, (end - start) / pitch, 48).unwrap();
|
||
let cut = kernel::faceted_boolean(body, &groove, kernel::BoolOp::Cut, pitch * 0.005).unwrap().unwrap();
|
||
assert!(cut.validity().is_empty(), "{:?}", cut.validity());
|
||
let before = body.mesh(&solidcraft_kernel::MeshTolerance::chord(0.001)).unwrap().measure().volume;
|
||
let after = cut.mesh(&solidcraft_kernel::MeshTolerance::chord(0.001)).unwrap().measure().volume;
|
||
assert!(before - after > 700.0 && before - after < 1800.0, "removed {}", before - after);
|
||
}
|
||
|
||
#[test]
|
||
fn modelled_full_length_m44_flange_thread() {
|
||
let mut s = Session::default();
|
||
let sample = crate::sample::samples().into_iter().find(|s| s.name == "Bolted Flange").unwrap();
|
||
s.run_script(&(sample.script)()).unwrap();
|
||
let before = volume(&mut s, "Flange");
|
||
run(
|
||
&mut s,
|
||
"solid.thread",
|
||
json!({
|
||
"face": [-19.034766861657907, -11.03075929038123, 19.574640342897094],
|
||
"designation": "M44x1.5", "modeled": true
|
||
}),
|
||
);
|
||
let state = s.model.state();
|
||
let body = &state.body("Flange").unwrap().body;
|
||
assert!(body.validity().is_empty(), "{:?}", body.validity());
|
||
let removed = before - volume(&mut s, "Flange");
|
||
assert!(removed > 700.0 && removed < 1800.0, "a full-length helical cut removes material: {removed}");
|
||
}
|
||
|
||
#[test]
|
||
fn modelled_full_length_fine_threads_on_large_shafts() {
|
||
for (d, p, len) in [(44.0, 1.0, 5.0), (44.0, 1.5, 16.0), (100.0, 1.5, 6.0)] {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius":d / 2.0,"height":len,"body_name":"Shaft"}));
|
||
let before = volume(&mut s, "Shaft");
|
||
run(&mut s, "solid.thread", json!({"face":[d / 2.0,0,len / 2.0],"designation":format!("M{d}x{p}"),"modeled":true}));
|
||
let state = s.model.state();
|
||
let body = &state.body("Shaft").unwrap().body;
|
||
assert!(body.validity().is_empty(), "M{d}x{p}: {:?}", body.validity());
|
||
let root = d / 2.0 - 5.0 * p * 3f64.sqrt() / 16.0;
|
||
let want = per_turn(root, d / 2.0, |r| p / 4.0 + 2.0 * (r - root) * (PI / 6.0).tan()) * len / p;
|
||
let got = before - volume(&mut s, "Shaft");
|
||
assert!((got - want).abs() < want * 0.04, "M{d}x{p}: removed {got}, ISO profile {want}");
|
||
}
|
||
}
|
||
|
||
/// Issue 2705: an M14 over the top 10 mm of a 14.6 mm boss on a plate. A modelled thread never
|
||
/// changes the size of the shaft it is on (#1018, #2853): it is refused with the size to make
|
||
/// the shaft, and the part is unchanged (tests/kernel-cases/threads/2705).
|
||
#[test]
|
||
fn an_m14_thread_on_a_14_6_mm_boss_is_refused_with_the_size_to_make_it() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"corner": [-10, -10, 0], "length": 20, "width": 20, "height": 4, "body_name": "Part"}));
|
||
run(&mut s, "solid.cylinder", json!({"radius": 7.3, "height": 15, "base": [0, 0, 4], "operation": "join", "targets": ["Part"]}));
|
||
let before = volume(&mut s, "Part");
|
||
let thread = json!({"face": [7.3, 0, 17], "designation": "M14", "length": 10, "modeled": true});
|
||
let e = s.execute("solid.thread", &thread).err().map(|e| e.to_string()).unwrap_or_default();
|
||
assert!(e.contains("this 14.6 mm shaft is too thick for a modelled M14 thread; make the shaft 14 mm for M14"), "{e}");
|
||
assert!((volume(&mut s, "Part") - before).abs() < 1e-9);
|
||
}
|
||
|
||
/// A shaft thinner than the thread's minor diameter is refused, and so is a thread on a shaft
|
||
/// far thicker than it.
|
||
#[test]
|
||
fn a_shaft_far_off_the_threads_size_is_refused() {
|
||
let refused = |s: &mut Session, body: &str, p: Value| {
|
||
let before = volume(s, body);
|
||
let e = s.execute("solid.thread", &p).err().map(|e| e.to_string()).unwrap_or_default();
|
||
assert!((volume(s, body) - before).abs() < 1e-9, "{p}: {e}");
|
||
e
|
||
};
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 2.4, "height": 10, "body_name": "Shaft"}));
|
||
let e = refused(&mut s, "Shaft", json!({"face": [2.4, 0, 5], "designation": "M6", "modeled": true}));
|
||
assert!(e.contains("does not fit a 4.80 mm shaft") || e.contains("too thin"), "{e}");
|
||
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 4, "height": 10, "body_name": "Shaft"}));
|
||
let e = refused(&mut s, "Shaft", json!({"face": [4, 0, 5], "designation": "M6"}));
|
||
assert!(e.contains("an M6 thread does not fit a 8.00 mm shaft"), "{e}");
|
||
|
||
let e = refused(&mut s, "Shaft", json!({"face": [4, 0, 5], "designation": "M6", "modeled": true}));
|
||
assert!(e.contains("an M6 thread does not fit a 8.00 mm shaft"), "{e}");
|
||
}
|
||
|
||
#[test]
|
||
fn a_thread_without_a_coarse_pitch_suggests_explicit_pitches() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 14, "height": 10, "body_name": "Shaft"}));
|
||
let saved = s.doc.to_json();
|
||
for designation in ["M28", "m28", " M28 "] {
|
||
let e = s.execute("solid.thread", &json!({"face": [14, 0, 5], "designation": designation})).unwrap_err().to_string();
|
||
assert!(e.contains("has no coarse ISO pitch") && e.contains("M28x2") && e.contains("M28x1.5"), "{e}");
|
||
assert_eq!(s.doc.to_json(), saved);
|
||
}
|
||
for designation in ["MNaN", "Minf", "M-28", "M0", "M1e9", "M1e999", "M28x", "M28xNaN"] {
|
||
let e = s.execute("solid.thread", &json!({"face": [14, 0, 5], "designation": designation})).unwrap_err().to_string();
|
||
// Each thread form names itself in its refusal: `unknown metric thread`.
|
||
assert!(e.contains("unknown metric thread"), "{designation}: {e}");
|
||
assert_eq!(s.doc.to_json(), saved);
|
||
}
|
||
run(&mut s, "solid.thread", json!({"face": [14, 0, 5], "designation": "M28x2"}));
|
||
}
|
||
|
||
#[test]
|
||
fn automatic_sizing_past_the_coarse_range_suggests_a_size_with_its_pitch() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 37.5, "height": 10, "body_name": "Shaft"}));
|
||
let saved = s.doc.to_json();
|
||
let e = s.execute("solid.thread", &json!({"face": [37.5, 0, 5]})).unwrap_err().to_string();
|
||
assert!(e.contains("beyond the coarse thread range (up to M56)") && e.contains("M75x3 or M75x2"), "{e}");
|
||
assert_eq!(s.doc.to_json(), saved);
|
||
run(&mut s, "solid.thread", json!({"face": [37.5, 0, 5], "designation": "M75x2"}));
|
||
}
|
||
|
||
#[test]
|
||
fn a_threaded_hole_without_a_coarse_pitch_suggests_explicit_pitches() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length": 40, "width": 40, "height": 10}));
|
||
let saved = s.doc.to_json();
|
||
let e = s.execute("solid.hole", &json!({"position": [20, 20, 10], "thread": "M28"})).unwrap_err().to_string();
|
||
assert!(e.contains("has no coarse ISO pitch") && e.contains("M28x2") && e.contains("M28x1.5"), "{e}");
|
||
assert_eq!(s.doc.to_json(), saved);
|
||
}
|
||
|
||
#[test]
|
||
fn non_finite_thread_designations_are_refused_without_changing_the_design() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius":4,"height":10}));
|
||
let saved = s.doc.to_json();
|
||
for designation in ["Minfx1", "M8xinf", "MNaNx1", "M8xNaN", "M1e999x1"] {
|
||
let result = s.execute("solid.thread", &json!({"face":[4,0,2],"designation":designation}));
|
||
assert!(result.is_err(), "{designation}: {result:?}");
|
||
assert_eq!(s.doc.to_json(), saved);
|
||
}
|
||
}
|
||
|
||
/// ∫ 2π r · width(r) dr over [a, b]: the volume one turn of the groove takes out (a screw
|
||
/// motion of a section in an axial plane sweeps 2π∫r dA per turn).
|
||
fn per_turn(a: f64, b: f64, width: impl Fn(f64) -> f64) -> f64 {
|
||
let n = 400;
|
||
(0..n).map(|i| a + (b - a) * (i as f64 + 0.5) / n as f64).map(|r| 2.0 * PI * r * width(r) * (b - a) / n as f64).sum()
|
||
}
|
||
|
||
#[test]
|
||
fn modelled_external_threads_m3_to_m20() {
|
||
let h = |p: f64| p * 3f64.sqrt() / 2.0;
|
||
let slope = (PI / 6.0).tan();
|
||
for (d, p) in SIZES {
|
||
let mut s = Session::default();
|
||
let len = 4.0 * p;
|
||
run(&mut s, "solid.cylinder", json!({"radius": d / 2.0, "height": len + 2.0, "body_name": "Shaft"}));
|
||
let before = volume(&mut s, "Shaft");
|
||
let th = run(&mut s, "solid.thread", json!({"face": [d / 2.0, 0, 1], "length": len, "modeled": true}));
|
||
assert!(th["thread"].is_null(), "a modelled thread is real geometry, not an annotation: {th}");
|
||
let r_root = d / 2.0 - 5.0 * h(p) / 8.0;
|
||
let want = per_turn(r_root, d / 2.0, |r| p / 4.0 + 2.0 * (r - r_root) * slope) * len / p;
|
||
let got = before - volume(&mut s, "Shaft");
|
||
assert!((got - want).abs() < want * 0.03, "M{d}: removed {got}, ISO profile {want}");
|
||
}
|
||
}
|
||
|
||
#[test]
|
||
fn modelled_internal_threads_m3_to_m20() {
|
||
let h = |p: f64| p * 3f64.sqrt() / 2.0;
|
||
let slope = (PI / 6.0).tan();
|
||
for (d, p) in SIZES {
|
||
let mut s = Session::default();
|
||
let len = 4.0 * p;
|
||
let d1 = d - 2.0 * 5.0 * h(p) / 8.0;
|
||
run(&mut s, "solid.box", json!({"corner": [-d, -d, 0], "length": 2.0 * d, "width": 2.0 * d, "height": len, "body_name": "Nut"}));
|
||
run(&mut s, "solid.cylinder", json!({"base": [0, 0, -1], "radius": d1 / 2.0, "height": len + 2.0, "body_name": "Bore"}));
|
||
run(&mut s, "solid.combine", json!({"target": "Nut", "tools": ["Bore"], "operation": "cut"}));
|
||
let before = volume(&mut s, "Nut");
|
||
let th = run(&mut s, "solid.thread", json!({"face": [d1 / 2.0, 0, len / 2.0], "modeled": true}));
|
||
assert!(th["thread"].is_null(), "{th}");
|
||
// Bolt-shaped space: P/8 flat at the major diameter, widening towards the bore.
|
||
let want = per_turn(d1 / 2.0, d / 2.0, |r| p / 8.0 + 2.0 * (d / 2.0 - r) * slope) * len / p;
|
||
let got = before - volume(&mut s, "Nut");
|
||
assert!((got - want).abs() < want * 0.03, "M{d}: removed {got}, ISO profile {want}");
|
||
}
|
||
}
|
||
|
||
/// Issue 995: an M5 modelled thread in a 5 mm hole cut nothing (the groove lay in the hole, from
|
||
/// the minor diameter out to the 5 mm major one) and only left the wall faceted. A modelled thread
|
||
/// that would cut next to nothing is refused, with the drill to use and the size that fits;
|
||
/// a cosmetic one is still only a note.
|
||
#[test]
|
||
fn a_modelled_thread_that_would_cut_nothing_is_refused() {
|
||
let mut s = hex_nut(5.0);
|
||
let before = volume(&mut s, "Nut");
|
||
let e = s.execute("solid.thread", &json!({"face": [2.5, 0, 2], "designation": "M5", "modeled": true})).err().map(|e| e.to_string());
|
||
let e = e.unwrap_or_default();
|
||
assert!(e.contains("this 5 mm hole") && e.contains("drill 4.2 mm for M5") && e.contains("thread this hole M6"), "{e}");
|
||
assert!((volume(&mut s, "Nut") - before).abs() < 1e-9);
|
||
run(&mut s, "solid.thread", json!({"face": [2.5, 0, 2], "designation": "M5"}));
|
||
|
||
// A shaft no thicker than the thread's root (17.29 mm for M20) is refused the same way.
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 8.6, "height": 10, "body_name": "Shaft"}));
|
||
let e = s.execute("solid.thread", &json!({"face": [8.6, 0, 5], "designation": "M20", "modeled": true})).err().map(|e| e.to_string());
|
||
let e = e.unwrap_or_default();
|
||
assert!(e.contains("this 17.2 mm shaft") && e.contains("make the shaft 20 mm for M20") && e.contains("thread this shaft M18"), "{e}");
|
||
}
|
||
|
||
/// Issue 2688: an M8 modelled thread in a 6 mm hole (narrower than its 6.65 mm minor diameter)
|
||
/// was refused as "the face is too far from the thread's diameter". It says what is wrong and
|
||
/// what to drill, as a hole that is too wide does; and the same for a shaft that is too thick.
|
||
#[test]
|
||
fn a_hole_too_narrow_or_a_shaft_too_thick_says_which_and_what_fits() {
|
||
let mut s = hex_nut(6.0);
|
||
let before = volume(&mut s, "Nut");
|
||
let e = s.execute("solid.thread", &json!({"face": [3.0, 0, 2], "designation": "M8", "modeled": true})).err().map(|e| e.to_string());
|
||
let e = e.unwrap_or_default();
|
||
assert!(e.contains("this 6 mm hole is too narrow for a modelled M8 thread") && e.contains("drill 6.8 mm for M8"), "{e}");
|
||
assert!(!e.contains("too far"), "{e}");
|
||
assert!((volume(&mut s, "Nut") - before).abs() < 1e-9);
|
||
|
||
let mut s = Session::default();
|
||
// 9 mm is close enough to M8 to be offered it, too thick to cut it.
|
||
run(&mut s, "solid.cylinder", json!({"radius": 4.5, "height": 10, "body_name": "Shaft"}));
|
||
let e = s.execute("solid.thread", &json!({"face": [4.5, 0, 5], "designation": "M8", "modeled": true})).err().map(|e| e.to_string());
|
||
let e = e.unwrap_or_default();
|
||
assert!(e.contains("this 9 mm shaft is too thick for a modelled M8 thread") && e.contains("make the shaft 8 mm for M8"), "{e}");
|
||
}
|
||
|
||
/// The limit is a quarter of the basic depth 5H/8: a hole up to 4.78 mm for M5 (4.86 mm for
|
||
/// M5x0.5) still takes a modelled thread, a wider one is refused with that pitch's drill.
|
||
#[test]
|
||
fn the_cut_nothing_limit_holds_for_coarse_and_fine_pitch() {
|
||
for (m, hole, refused) in [
|
||
("M5", 4.5, None),
|
||
("M5", 4.75, None),
|
||
("M5", 4.8, Some("drill 4.2 mm for M5, or thread this hole M6")),
|
||
("M5x0.5", 4.5, None),
|
||
("M5x0.5", 4.85, None),
|
||
("M5x0.5", 4.9, Some("drill 4.5 mm for M5x0.5, or thread this hole M6")),
|
||
("M5x0.5", 5.0, Some("drill 4.5 mm for M5x0.5, or thread this hole M6")),
|
||
] {
|
||
let mut s = hex_nut(hole);
|
||
let before = volume(&mut s, "Nut");
|
||
let made = s.execute("solid.thread", &json!({"face": [hole / 2.0, 0, 2], "designation": m, "modeled": true}));
|
||
let cut = before - volume(&mut s, "Nut");
|
||
match (refused, made) {
|
||
(None, Ok(_)) => assert!(cut > 0.05, "{m} in {hole} mm: removed {cut}"),
|
||
(Some(want), Err(e)) => {
|
||
let e = e.to_string();
|
||
assert!(e.contains(&format!("this {hole} mm hole")) && e.contains(want), "{m} in {hole} mm: {e}");
|
||
assert!(cut.abs() < 1e-9, "{m} in {hole} mm: removed {cut}");
|
||
}
|
||
(want, got) => panic!("{m} in {hole} mm: want refused {want:?}, got {:?}", got.map(|_| ())),
|
||
}
|
||
}
|
||
}
|
||
|
||
/// A 4 mm hex nut (inscribed radius 5) with a plain hole of this diameter through it.
|
||
fn hex_nut(hole: f64) -> Session {
|
||
let mut s = Session::default();
|
||
for (id, p) in [
|
||
("sketch.create", json!({"plane": "XY"})),
|
||
("sketch.polygon.inscribed", json!({"center": [0, 0], "radius": 5, "sides": 6})),
|
||
("sketch.finish", json!({})),
|
||
("solid.extrude", json!({"distance": 4, "body_name": "Nut"})),
|
||
("solid.hole", json!({"position": [0, 0, 4], "diameter": hole})),
|
||
] {
|
||
run(&mut s, id, p);
|
||
}
|
||
s
|
||
}
|
||
|
||
/// Issue 602: rounding the edges of a hex boss on a threaded shaft froze the app. The thread's
|
||
/// thousands of facets were healed pair by pair, once per feature after it, and the fillet's
|
||
/// preview then compared each of them with the whole old body. With SMLib the thread is exact (a
|
||
/// few dozen faces). The 4 mm thread starts at the shaft's free bottom end: the hex's corners
|
||
/// (2.31 mm out, past the M5 root at 2.07 mm) stand in the groove's way at the top end.
|
||
#[test]
|
||
fn fillet_beside_a_modelled_thread_finishes() {
|
||
let mut s = Session::default();
|
||
for (id, p) in [
|
||
("sketch.create", json!({"plane": "XY"})),
|
||
("sketch.circle.center", json!({"center": [0, 0], "diameter": 5})),
|
||
("sketch.finish", json!({})),
|
||
("solid.extrude", json!({"distance": 10, "body_name": "Screw"})),
|
||
("sketch.create", json!({"plane": {"face": [0, 0, 10]}})),
|
||
("sketch.polygon.circumscribed", json!({"center": [0, 0], "radius": 2, "sides": 6})),
|
||
("sketch.finish", json!({})),
|
||
("solid.extrude", json!({"distance": 3, "profiles": [{"point": [0, 0]}], "operation": "join", "targets": ["Screw"]})),
|
||
("solid.thread", json!({"face": [2.5, 0, 5], "designation": "M5", "length": 4, "modeled": true})),
|
||
] {
|
||
run(&mut s, id, p);
|
||
}
|
||
let volume_before = volume(&mut s, "Screw");
|
||
let top: Vec<Value> = (0..6)
|
||
.map(|i| {
|
||
let a = (30.0 + 60.0 * i as f64).to_radians();
|
||
json!([2.0 * a.cos(), 2.0 * a.sin(), 13])
|
||
})
|
||
.collect();
|
||
let started = std::time::Instant::now();
|
||
run(&mut s, "solid.fillet", json!({"edges": top, "radius": 0.3}));
|
||
assert!(started.elapsed().as_secs() < 30, "the fillet took {:?}", started.elapsed());
|
||
let volume_after = volume(&mut s, "Screw");
|
||
assert!(volume_after < volume_before && volume_after > volume_before * 0.99, "{volume_before} -> {volume_after}");
|
||
}
|
||
|
||
/// The SMLib volume of a body (exact surfaces), for closed-form checks.
|
||
fn exact_volume(s: &Session, b: &str) -> f64 {
|
||
let st = s.model.state();
|
||
st.body(b).map(|mb| solidcraft_kernel::measure(&mb.body).unwrap().volume).unwrap_or(0.0)
|
||
}
|
||
|
||
/// One turn of the ISO 68-1 external groove inside a shaft of radius `rs` (its section clipped at
|
||
/// the surface): 2π∫ r g(r) dr from the root, g = P/4 + 2 (r - root) tan 30°.
|
||
fn ext_turn(d: f64, p: f64, rs: f64) -> f64 {
|
||
let root = d / 2.0 - 5.0 * p * 3f64.sqrt() / 16.0;
|
||
let (a, b) = (p / 4.0 - 2.0 * root * (PI / 6.0).tan(), 2.0 * (PI / 6.0).tan());
|
||
let f = |r: f64| a * r * r / 2.0 + b * r * r * r / 3.0;
|
||
2.0 * PI * (f(rs) - f(root))
|
||
}
|
||
|
||
/// The groove's half width at its widest: for an external thread at the tool's outer edge,
|
||
/// 0.05 P past the crest (the section reaches past the surface so the cut leaves no skin).
|
||
fn ext_half_width(d: f64, p: f64) -> f64 {
|
||
let root = d / 2.0 - 5.0 * p * 3f64.sqrt() / 16.0;
|
||
(p / 4.0 + 2.0 * (d / 2.0 + 0.05 * p - root) * (PI / 6.0).tan()) / 2.0
|
||
}
|
||
|
||
/// A d10 shaft (z 10..35) on a d16 collar (z 0..10), as ladder 06/004.
|
||
fn shaft_on_collar() -> Session {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 8, "height": 10, "body_name": "Part"}));
|
||
run(&mut s, "solid.cylinder", json!({"base": [0, 0, 10], "radius": 5, "height": 25, "operation": "join", "targets": ["Part"]}));
|
||
s
|
||
}
|
||
|
||
/// Rig 602, ladder 06/004: a thread on a shaft ran a pitch past both ends of its face, into the
|
||
/// collar below as into the air above. At a shoulder it stops with its widest part clear of it:
|
||
/// the collar keeps its whole π 8² 10, and the groove takes (25 - w)/P turns, w its half width
|
||
/// (a square stop inside material takes exactly its length over P, the section being symmetric).
|
||
#[test]
|
||
fn a_thread_stops_clear_of_a_shoulder() {
|
||
let mut s = shaft_on_collar();
|
||
run(&mut s, "solid.thread", json!({"face": [5, 0, 25], "designation": "M10", "modeled": true}));
|
||
let (p, w) = (1.5, ext_half_width(10.0, 1.5));
|
||
let want = PI * 64.0 * 10.0 + PI * 25.0 * 25.0 - (25.0 - w) / p * ext_turn(10.0, p, 5.0);
|
||
let got = exact_volume(&s, "Part");
|
||
assert!((got - want).abs() < want * 2e-4, "{got} vs {want}");
|
||
}
|
||
|
||
/// A d10 boss (z t..t+16) on a plate t thick, threaded M10: the plate's top is the shoulder.
|
||
/// The groove, with or without its runout, stays on the boss: the plate keeps all of itself
|
||
/// (what lies below z = t after the boss is cut away), and without a runout the boss loses
|
||
/// (16 - w)/P turns, as at a collar. The owner's bug: built as the app builds it (a rounded
|
||
/// plate, a circle sketched on its top face and extruded with Join), a plate thinner than 1.5 P
|
||
/// had no material where the free-end test looked (1 to 1.5 pitches past the face), so its top
|
||
/// was taken for a free end and the overrun cut a pitch into it.
|
||
#[test]
|
||
fn a_thread_on_a_boss_never_cuts_into_the_plate_below() {
|
||
let boss = |t: f64, extra: Value| {
|
||
let mut s = Session::default();
|
||
run(&mut s, "sketch.create", json!({"plane": "XY"}));
|
||
run(&mut s, "sketch.rectangle.rounded", json!({"p0": [-20, -20], "p1": [20, 20], "radius": 5}));
|
||
run(&mut s, "sketch.finish", json!({}));
|
||
run(&mut s, "solid.extrude", json!({"distance": t}));
|
||
run(&mut s, "sketch.create", json!({"plane": {"face": [0, 0, t]}}));
|
||
run(&mut s, "sketch.circle.center", json!({"center": [0, 0], "radius": 5}));
|
||
run(&mut s, "sketch.finish", json!({}));
|
||
run(&mut s, "solid.extrude", json!({"distance": 16, "operation": "join"}));
|
||
assert_eq!(s.model.state().bodies.len(), 1);
|
||
let mut p = json!({"face": [5, 0, t + 8.0], "modeled": true});
|
||
if let (Some(p), Value::Object(e)) = (p.as_object_mut(), extra) {
|
||
p.extend(e);
|
||
}
|
||
run(&mut s, "solid.thread", p);
|
||
s
|
||
};
|
||
let plate_left = |mut s: Session, t: f64| {
|
||
run(
|
||
&mut s,
|
||
"solid.box",
|
||
json!({"corner": [-30, -30, t], "length": 60, "width": 60, "height": 30, "body_name": "Above", "operation": "new_body"}),
|
||
);
|
||
run(&mut s, "solid.combine", json!({"target": "Body1", "tools": ["Above"], "operation": "cut"}));
|
||
exact_volume(&s, "Body1")
|
||
};
|
||
let plate = |t: f64| (40.0 * 40.0 - (4.0 - PI) * 25.0) * t;
|
||
let (p, w) = (1.5, ext_half_width(10.0, 1.5));
|
||
for t in [6.0, 1.0] {
|
||
let s = boss(t, json!({}));
|
||
let want = plate(t) + PI * 25.0 * 16.0 - (16.0 - w) / p * ext_turn(10.0, p, 5.0);
|
||
let got = exact_volume(&s, "Body1");
|
||
assert!((got - want).abs() < want * 2e-4, "plate {t}: {got} vs {want}");
|
||
let left = plate_left(s, t);
|
||
assert!((left - plate(t)).abs() < 1e-6 * plate(t), "plate {t}: lost {} mm³", plate(t) - left);
|
||
}
|
||
for extra in [json!({"ease_out": "standard"}), json!({"ease_out": "short", "tip": "both"})] {
|
||
let s = boss(1.0, extra.clone());
|
||
assert!(s.model.state().body("Body1").unwrap().body.validity().is_empty(), "{extra}");
|
||
let left = plate_left(s, 1.0);
|
||
assert!((left - plate(1.0)).abs() < 1e-6 * plate(1.0), "{extra}: the plate below the boss lost {} mm³", plate(1.0) - left);
|
||
}
|
||
}
|
||
|
||
/// Rig 602: "from the end nearest the pick" took the head end for a pick a little above the
|
||
/// middle. A thread of limited length starts at the face's only free end, wherever it is picked.
|
||
#[test]
|
||
fn a_thread_of_some_length_starts_at_the_only_free_end() {
|
||
let mut s = shaft_on_collar();
|
||
let th = run(&mut s, "solid.thread", json!({"face": [5, 0, 15], "designation": "M10", "length": 6}));
|
||
let (a, b) = (th["thread"]["start"].as_f64().unwrap(), th["thread"]["end"].as_f64().unwrap());
|
||
// The axis points up (+z) from the shaft's own axis point; the free end is the top, z = 35.
|
||
let k = th["thread"]["axis"][2].as_f64().unwrap();
|
||
let z = |t: f64| th["thread"]["axis_point"][2].as_f64().unwrap() + k * t;
|
||
let (z0, z1) = (z(a).min(z(b)), z(a).max(z(b)));
|
||
assert!((z0 - 29.0).abs() < 1e-6 && (z1 - 35.0).abs() < 1e-6, "{th}");
|
||
}
|
||
|
||
/// Ladder 06/003: a pick in the middle of a face whose two ends are both free was a coin toss
|
||
/// (it fell to whichever end rounding favoured). It is refused, naming `from`; with `from` it runs
|
||
/// from that end, and a square stop inside the face takes exactly length / P turns.
|
||
#[test]
|
||
fn a_mid_face_pick_between_two_free_ends_needs_from() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 5, "height": 30, "body_name": "Part"}));
|
||
let e = s.execute("solid.thread", &json!({"face": [5, 0, 15], "designation": "M10", "length": 15, "modeled": true}));
|
||
let e = e.err().map(|e| e.to_string()).unwrap_or_default();
|
||
assert!(e.contains("both ends of the face are free") && e.contains("`from`"), "{e}");
|
||
run(&mut s, "solid.thread", json!({"face": [5, 0, 15], "designation": "M10", "length": 15, "from": [0, 0, 30], "modeled": true}));
|
||
let want = PI * 25.0 * 30.0 - 10.0 * ext_turn(10.0, 1.5, 5.0);
|
||
let got = exact_volume(&s, "Part");
|
||
assert!((got - want).abs() < want * 2e-4, "{got} vs {want}");
|
||
// The groove is all in the top half: just under the surface, the bottom 15 mm (less the
|
||
// stop's half width) is whole and the top has the groove's turns.
|
||
let st = s.model.state();
|
||
let body = &st.body("Part").unwrap().body;
|
||
let ring = |z: f64| (0..36).map(|i| (i as f64 * 10.0).to_radians()).map(move |a| Vec3::new(4.9 * a.cos(), 4.9 * a.sin(), z));
|
||
let rings = |z0: f64, z1: f64| (0..=40).map(move |i| z0 + (z1 - z0) * i as f64 / 40.0).flat_map(ring);
|
||
assert!(rings(0.5, 14.0).all(|q| body.contains(q)), "the bottom half is cut");
|
||
assert!(rings(16.0, 29.5).filter(|q| !body.contains(*q)).count() > 100, "the top half is not threaded");
|
||
}
|
||
|
||
/// Up to a plane, or to a point's place along the axis, from the end given.
|
||
#[test]
|
||
fn a_thread_runs_up_to_a_plane_or_a_point() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 4, "height": 20, "body_name": "Shaft"}));
|
||
let z = |th: &Value| {
|
||
let t = &th["thread"];
|
||
let at = |u: &str| t["axis_point"][2].as_f64().unwrap() + t["axis"][2].as_f64().unwrap() * t[u].as_f64().unwrap();
|
||
let (a, b) = (at("start"), at("end"));
|
||
(a.min(b), a.max(b))
|
||
};
|
||
let th = run(&mut s, "solid.thread", json!({"face": [4, 0, 10], "up_to": {"origin": [0, 0, 12], "normal": [0, 0, 1]}, "from": [0, 0, 0]}));
|
||
let (z0, z1) = z(&th);
|
||
assert!(z0.abs() < 1e-6 && (z1 - 12.0).abs() < 1e-6, "{th}");
|
||
let th = run(&mut s, "solid.thread", json!({"face": [4, 0, 10], "extent": "up_to", "up_to": [4, 0, 5], "from": [0, 0, 20]}));
|
||
let (z0, z1) = z(&th);
|
||
assert!((z0 - 5.0).abs() < 1e-6 && (z1 - 20.0).abs() < 1e-6, "{th}");
|
||
// An extent that contradicts the values given is refused.
|
||
let e = s.execute("solid.thread", &json!({"face": [4, 0, 10], "extent": "full", "length": 5})).err().map(|e| e.to_string());
|
||
assert!(e.unwrap_or_default().contains("extent: full"));
|
||
}
|
||
|
||
/// A blind tapped hole: the thread runs out of the entry and stops clear of the bottom, the
|
||
/// groove taking (depth - w)/P turns of 2π∫ r g(r) dr over the wall, w its widest half width (at
|
||
/// the tool's inner edge, 0.1 P inside the minor diameter).
|
||
#[test]
|
||
fn a_blind_tapped_hole_stops_clear_of_its_bottom() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"corner": [-10, -10, 0], "length": 20, "width": 20, "height": 20, "body_name": "Block"}));
|
||
run(&mut s, "solid.hole", json!({"position": [0, 0, 20], "diameter": 8.5, "depth": 12}));
|
||
let before = exact_volume(&s, "Block");
|
||
run(&mut s, "solid.thread", json!({"face": [4.25, 0, 14], "designation": "M10", "modeled": true}));
|
||
let (d, p, rh) = (10.0, 1.5, 4.25);
|
||
let t = (PI / 6.0).tan();
|
||
let minor = d / 2.0 - 5.0 * p * 3f64.sqrt() / 16.0;
|
||
let w = (p / 8.0 + 2.0 * (d / 2.0 - (minor - 0.1 * p)) * t) / 2.0;
|
||
// g(r) = P/8 + 2 (d/2 - r) tan 30°, over the wall r 4.25..5.
|
||
let f = |r: f64| (p / 8.0 + d * t) * r * r / 2.0 - 2.0 * t * r * r * r / 3.0;
|
||
let turn = 2.0 * PI * (f(d / 2.0) - f(rh));
|
||
let want = before - (12.0 - w) / p * turn;
|
||
let got = exact_volume(&s, "Block");
|
||
assert!((got - want).abs() < before * 1e-4, "{got} vs {want}");
|
||
}
|
||
|
||
/// A form's groove width at radius r between its root and crest: the pitch less the tooth, the
|
||
/// tooth `flat` wide at the crest radius `crest` and widening by tan a + tan b per unit of depth.
|
||
fn form_turn(p: f64, flat: f64, crest: f64, a: f64, b: f64, r0: f64, r1: f64, internal: bool) -> f64 {
|
||
let t = a.to_radians().tan() + b.to_radians().tan();
|
||
let n = 2000;
|
||
let w = |r: f64| p - flat - (if internal { r - crest } else { crest - r }) * t;
|
||
(0..n).map(|i| r0 + (r1 - r0) * (i as f64 + 0.5) / n as f64).map(|r| 2.0 * PI * r * w(r) * (r1 - r0) / n as f64).sum()
|
||
}
|
||
|
||
/// Every standard form cut into a shaft of its major diameter over six turns, right- and
|
||
/// left-handed: the groove takes 2π∫ r w(r) dr per turn (Pappus on the section, screw motion),
|
||
/// w from the standard's profile, from its external minor diameter to the shaft's surface.
|
||
#[test]
|
||
fn every_form_cuts_its_standard_profile() {
|
||
let inch = 25.4;
|
||
// (form, designation, d, P, crest flat, flanks, external minor radius)
|
||
let tr_ac = 0.25;
|
||
let acme_a = 0.020 * inch;
|
||
let t3 = 3f64.to_radians().tan() + 30f64.to_radians().tan();
|
||
let t7 = 7f64.to_radians().tan() + 1.0;
|
||
let cases = [
|
||
("trapezoidal", "Tr20x4", 20.0, 4.0, 2.0 * (1.0 - 15f64.to_radians().tan()), (15.0, 15.0), 10.0 - 2.0 - tr_ac),
|
||
(
|
||
"acme",
|
||
"3/4-6 ACME",
|
||
0.75 * inch,
|
||
inch / 6.0,
|
||
inch / 12.0 * (1.0 - 14.5f64.to_radians().tan()),
|
||
(14.5, 14.5),
|
||
0.375 * inch - inch / 12.0 - acme_a / 2.0,
|
||
),
|
||
("buttress", "S20x4", 20.0, 4.0, (4.0 - 3.0 * t3) / 2.0, (3.0, 30.0), 10.0 - 0.86777 * 4.0),
|
||
(
|
||
"buttress_asme",
|
||
"1.5-8 BUTT",
|
||
1.5 * inch,
|
||
inch / 8.0,
|
||
(inch / 8.0 - 0.6 * inch / 8.0 * t7) / 2.0,
|
||
(7.0, 45.0),
|
||
0.75 * inch - 0.6 * inch / 8.0,
|
||
),
|
||
];
|
||
for (form, designation, d, p, flat, (a, b), r3) in cases {
|
||
let mut volumes = Vec::new();
|
||
for hand in ["right", "left"] {
|
||
let mut s = Session::default();
|
||
let len = 6.0 * p;
|
||
run(&mut s, "solid.cylinder", json!({"radius": d / 2.0, "height": len, "body_name": "Shaft"}));
|
||
let before = exact_volume(&s, "Shaft");
|
||
let th = run(
|
||
&mut s,
|
||
"solid.thread",
|
||
json!({"face": [d / 2.0, 0, len / 2.0], "form": form, "designation": designation, "hand": hand, "modeled": true}),
|
||
);
|
||
assert!(th["thread"].is_null(), "{th}");
|
||
let st = s.model.state();
|
||
assert!(st.body("Shaft").unwrap().body.validity().is_empty(), "{designation} {hand}");
|
||
let want = 6.0 * form_turn(p, flat, d / 2.0, a, b, r3, d / 2.0, false);
|
||
let got = before - exact_volume(&s, "Shaft");
|
||
assert!((got - want).abs() < want * 1e-4, "{designation} {hand}: removed {got}, the standard's profile {want}");
|
||
volumes.push(got);
|
||
}
|
||
assert!((volumes[0] - volumes[1]).abs() < volumes[0] * 1e-5, "{designation}: right {} left {}", volumes[0], volumes[1]);
|
||
}
|
||
}
|
||
|
||
/// A left-handed groove turns the other way: on the helix z = P θ / 2π (right-handed) the shaft
|
||
/// is cut once a turn, on z = -P θ / 2π it is cut all along. Both: a right- and a left-handed
|
||
/// groove, crossing.
|
||
#[test]
|
||
fn a_left_handed_thread_turns_the_other_way() {
|
||
let (d, p, len) = (10.0, 1.5, 9.0);
|
||
let r = (d / 2.0 + d / 2.0 - 5.0 * p * 3f64.sqrt() / 16.0) / 2.0;
|
||
let on = |s: &Session, sign: f64| -> usize {
|
||
let st = s.model.state();
|
||
let body = &st.body("Shaft").unwrap().body;
|
||
// Along each helix sense from every groove point on the z = 4.5 circle, count how often
|
||
// the line stays in the groove: a groove lies on one of them.
|
||
(0..36)
|
||
.filter(|i| {
|
||
let a0 = *i as f64 * 10f64.to_radians();
|
||
let z0 = 4.5;
|
||
let probe = |a: f64| Vec3::new(r * (a0 + a).cos(), r * (a0 + a).sin(), z0 + sign * p * a / std::f64::consts::TAU);
|
||
!body.contains(probe(0.0)) && (1..12).all(|k| !body.contains(probe(k as f64 * 0.5)))
|
||
})
|
||
.count()
|
||
};
|
||
let mut volumes = Vec::new();
|
||
for hand in ["right", "left", "both"] {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": d / 2.0, "height": len, "body_name": "Shaft"}));
|
||
let before = exact_volume(&s, "Shaft");
|
||
run(&mut s, "solid.thread", json!({"face": [5, 0, 4.5], "designation": "M10", "hand": hand, "modeled": true}));
|
||
assert!(s.model.state().body("Shaft").unwrap().body.validity().is_empty(), "{hand}");
|
||
let (right, left) = (on(&s, 1.0), on(&s, -1.0));
|
||
match hand {
|
||
"right" => assert!(right > 0 && left == 0, "right: {right} {left}"),
|
||
"left" => assert!(left > 0 && right == 0, "left: {right} {left}"),
|
||
_ => assert!(left > 0 && right > 0, "both: {right} {left}"),
|
||
}
|
||
volumes.push(before - exact_volume(&s, "Shaft"));
|
||
}
|
||
let want = 6.0 * ext_turn(d, p, d / 2.0);
|
||
assert!((volumes[0] - want).abs() < want * 1e-4 && (volumes[1] - want).abs() < want * 1e-4, "{volumes:?} vs {want}");
|
||
// Crossing, the two grooves share some of their volume.
|
||
assert!(volumes[2] > want * 1.2 && volumes[2] < 2.0 * want, "{volumes:?}");
|
||
}
|
||
|
||
/// A left-hand thread and tapped hole saved by v0.24.0 (format 39, `handedness: "left"`) open
|
||
/// left-handed; a tapped hole takes `hand` like a thread, never `both`, and only with a thread.
|
||
#[test]
|
||
fn a_format_39_left_hand_thread_and_tapped_hole_open_left_handed() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length": 60, "width": 60, "height": 12, "body_name": "Plate"}));
|
||
run(&mut s, "solid.hole", json!({"position": [20, 30, 12], "thread": "M6", "depth": 8, "hand": "left"}));
|
||
run(&mut s, "solid.cylinder", json!({"radius": 5, "height": 9, "base": [80, 0, 0], "body_name": "Shaft", "operation": "new"}));
|
||
run(&mut s, "solid.thread", json!({"face": [85, 0, 4.5], "designation": "M10", "hand": "left"}));
|
||
let hands = |s: &Session| -> Vec<solidcraft_doc::thread_forms::ThreadHand> { s.model.state().threads.iter().map(|t| t.hand).collect() };
|
||
let left = solidcraft_doc::thread_forms::ThreadHand::Left;
|
||
assert_eq!(hands(&s), [left, left]);
|
||
// What format 39 wrote: the direction as `handedness`, no pending changes.
|
||
let mut v: Value = serde_json::from_str(&s.doc.to_json()).unwrap();
|
||
v["format"] = json!("solidcraft/39");
|
||
v.as_object_mut().unwrap().remove("format_pending");
|
||
for f in v["features"].as_array_mut().unwrap() {
|
||
if let Some(h) = f.as_object_mut().unwrap().remove("hand") {
|
||
f["handedness"] = h;
|
||
}
|
||
}
|
||
let reopened = Session::new(solidcraft_doc::Document::from_json(&v.to_string()).unwrap());
|
||
assert_eq!(hands(&reopened), [left, left]);
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length": 60, "width": 60, "height": 12}));
|
||
for (params, why) in [
|
||
(json!({"position": [20, 30, 12], "thread": "M6", "depth": 8, "hand": "both"}), "unknown hand"),
|
||
(json!({"position": [20, 30, 12], "depth": 8, "hand": "left"}), "needs `thread`"),
|
||
] {
|
||
let err = s.execute("solid.hole", ¶ms).unwrap_err().to_string();
|
||
assert!(err.contains(why), "{err}");
|
||
}
|
||
}
|
||
|
||
/// A trapezoidal nut: the groove from the drilled minor diameter D1 = d - P out to the
|
||
/// internal root D4 = d + 2 ac (ISO 2904), 2π∫ r w(r) dr per turn.
|
||
#[test]
|
||
fn an_internal_trapezoidal_thread_cuts_out_to_its_root() {
|
||
let (d, p, ac) = (20.0, 4.0, 0.25);
|
||
let d1 = d - p;
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"corner": [-20, -20, 0], "length": 40, "width": 40, "height": 6.0 * p, "body_name": "Nut"}));
|
||
run(&mut s, "solid.cylinder", json!({"base": [0, 0, -1], "radius": d1 / 2.0, "height": 6.0 * p + 2.0, "body_name": "Bore"}));
|
||
run(&mut s, "solid.combine", json!({"target": "Nut", "tools": ["Bore"], "operation": "cut"}));
|
||
let before = exact_volume(&s, "Nut");
|
||
run(&mut s, "solid.thread", json!({"face": [d1 / 2.0, 0, 3.0 * p], "designation": "Tr20x4", "modeled": true}));
|
||
let flat = p / 2.0 * (1.0 - 15f64.to_radians().tan());
|
||
let want = 6.0 * form_turn(p, flat, d1 / 2.0, 15.0, 15.0, d1 / 2.0, d / 2.0 + ac, true);
|
||
let got = before - exact_volume(&s, "Nut");
|
||
assert!((got - want).abs() < want * 1e-4, "{got} vs {want}");
|
||
}
|
||
|
||
/// No current standard defines a square thread: it is refused, saying what to use.
|
||
#[test]
|
||
fn a_square_thread_is_refused() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 10, "height": 20}));
|
||
let e = s.execute("solid.thread", &json!({"face": [10, 0, 10], "form": "square", "designation": "20x4"})).err().map(|e| e.to_string());
|
||
assert!(e.unwrap_or_default().contains("no current standard defines a square thread"));
|
||
}
|
||
|
||
/// Ladder 06/008: n starts are n grooves of lead n P, each a turn's n-th further round: over the
|
||
/// same length they take n x L/(nP) turns, the volume of one start of that pitch, and do not
|
||
/// meet. A designation that gives the lead gives the starts.
|
||
#[test]
|
||
fn a_multi_start_thread_takes_the_volume_of_one_start() {
|
||
let (d, p, len) = (10.0, 1.5, 30.0);
|
||
let want = len / p * ext_turn(d, p, d / 2.0);
|
||
for (starts, designation) in [(2, "M10"), (3, "M10"), (1, "M10xPh3P1.5")] {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 5, "height": len, "body_name": "Shaft"}));
|
||
let before = exact_volume(&s, "Shaft");
|
||
run(&mut s, "solid.thread", json!({"face": [5, 0, 15], "designation": designation, "starts": starts, "modeled": true}));
|
||
let st = s.model.state();
|
||
assert!(st.body("Shaft").unwrap().body.validity().is_empty(), "{designation} x{starts}");
|
||
let got = before - exact_volume(&s, "Shaft");
|
||
assert!((got - want).abs() < want * 1e-4, "{designation} x{starts}: removed {got}, one start {want}");
|
||
}
|
||
// The cosmetic thread says it: two starts, lead 3.
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 20, "height": 40}));
|
||
let th = run(&mut s, "solid.thread", json!({"face": [20, 0, 20], "designation": "Tr40x14(P7)"}));
|
||
assert_eq!(th["thread"]["designation"], "Tr40x14(P7)", "{th}");
|
||
assert_eq!(th["thread"]["starts"], 2, "{th}");
|
||
let e = s.execute("solid.thread", &json!({"face": [20, 0, 20], "designation": "Tr40x14(P7)", "starts": 3})).err().map(|e| e.to_string());
|
||
assert!(e.unwrap_or_default().contains("has 2 start(s), not 3"));
|
||
}
|
||
|
||
/// The stock's volume after a modelled M10 thread, over sections z0..z1 whose outer radius is
|
||
/// `rmax(z)`: 2π∫∫ r m(r) dr dz, m the material fraction per pitch (1 under the root, 1 - w/P
|
||
/// in the groove's band). The groove's screw motion holds every meridian half-plane alike, and
|
||
/// an axisymmetric cut after it (a chamfer) only lowers rmax.
|
||
fn m10_stock(z0: f64, z1: f64, rmax: impl Fn(f64) -> f64) -> f64 {
|
||
let (d, p) = (10.0, 1.5);
|
||
let root = d / 2.0 - 5.0 * p * 3f64.sqrt() / 16.0;
|
||
let t = (PI / 6.0).tan();
|
||
// ∫_0^R r m(r) dr in closed form: R²/2 to the root, then m = a + b r (1 - (P/4 + 2 (r - root)
|
||
// tan 30°)/P) beyond it.
|
||
let ring = |rr: f64| {
|
||
let inner = rr.min(root);
|
||
let mut v = inner * inner / 2.0;
|
||
if rr > root {
|
||
let (a, b) = (1.0 - 0.25 + 2.0 * root * t / p, -2.0 * t / p);
|
||
let f = |r: f64| a * r * r / 2.0 + b * r * r * r / 3.0;
|
||
v += f(rr) - f(root);
|
||
}
|
||
v
|
||
};
|
||
let n = 20000;
|
||
(0..n).map(|i| z0 + (z1 - z0) * (i as f64 + 0.5) / n as f64).map(|z| 2.0 * PI * ring(rmax(z)) * (z1 - z0) / n as f64).sum()
|
||
}
|
||
|
||
/// ISO 4753's chamfered end on both free ends of an M10 stud: a 45° cone down to the external
|
||
/// minor diameter d3 (ISO 724), cut after the groove; the volume as the stock's chamfered section
|
||
/// with the thread's material fraction (as ladder 06/006). d3 lies below the modelled root, so
|
||
/// each end face is the whole disk of d3, with the cone a whole ring around it, not pinched
|
||
/// where the groove reaches the end.
|
||
#[test]
|
||
fn a_chamfered_tip_tapers_the_last_teeth() {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 5, "height": 30, "body_name": "Stud"}));
|
||
run(&mut s, "solid.thread", json!({"face": [5, 0, 15], "designation": "M10", "tip": "both", "modeled": true}));
|
||
let st = s.model.state();
|
||
let stud = &st.body("Stud").unwrap().body;
|
||
assert!(stud.validity().is_empty());
|
||
let rf = 5.0 - 17.0 / 24.0 * 1.5 * 3f64.sqrt() / 2.0;
|
||
let ends: Vec<f64> =
|
||
stud.faces(1e-4).unwrap().into_iter().filter(|f| f.plane_normal.is_some_and(|n| n.z.abs() > 0.999)).map(|f| f.area).collect();
|
||
assert_eq!(ends.len(), 2);
|
||
for a in ends {
|
||
assert!((a - PI * rf * rf).abs() < 1e-3 * a, "each end is a whole disk of d3: {a} vs {}", PI * rf * rf);
|
||
}
|
||
let want = m10_stock(0.0, 30.0, |z| 5f64.min(rf + z).min(rf + 30.0 - z));
|
||
let got = exact_volume(&s, "Stud");
|
||
assert!((got - want).abs() < want * 1e-4, "{got} vs {want}");
|
||
// 30° to the axis and 0.5 mm deep, at the one free end of a shaft on a collar.
|
||
let mut s = shaft_on_collar();
|
||
run(
|
||
&mut s,
|
||
"solid.thread",
|
||
json!({"face": [5, 0, 25], "designation": "M10", "tip": "both", "chamfer_angle": "30 deg", "chamfer_depth": 0.5, "modeled": true}),
|
||
);
|
||
let w = ext_half_width(10.0, 1.5);
|
||
let rf = 4.5;
|
||
let slope = 30f64.to_radians().tan();
|
||
let want = PI * 64.0 * 10.0 + PI * 25.0 * w + m10_stock(10.0 + w, 35.0, |z| 5f64.min(rf + (35.0 - z) * slope));
|
||
let got = exact_volume(&s, "Part");
|
||
assert!((got - want).abs() < want * 1e-4, "{got} vs {want}");
|
||
// Internal threads take a countersink instead.
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"corner": [-10, -10, 0], "length": 20, "width": 20, "height": 10, "body_name": "Nut"}));
|
||
run(&mut s, "solid.hole", json!({"position": [0, 0, 10], "diameter": 8.5}));
|
||
let e =
|
||
s.execute("solid.thread", &json!({"face": [4.25, 0, 5], "designation": "M10", "tip": "both", "modeled": true})).err().map(|e| e.to_string());
|
||
assert!(e.unwrap_or_default().contains("countersink"));
|
||
// ISO 4753 is for ISO metric threads: another form names its chamfer depth.
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 10, "height": 40, "body_name": "Screw"}));
|
||
let e = s
|
||
.execute("solid.thread", &json!({"face": [10, 0, 20], "designation": "Tr20x4", "tip": "both", "modeled": true}))
|
||
.err()
|
||
.map(|e| e.to_string());
|
||
assert!(e.unwrap_or_default().contains("chamfer depth"));
|
||
run(&mut s, "solid.thread", json!({"face": [10, 0, 20], "designation": "Tr20x4", "tip": "both", "chamfer_depth": 2.5, "modeled": true}));
|
||
assert!(s.model.state().body("Screw").unwrap().body.validity().is_empty());
|
||
}
|
||
|
||
/// `tip: start` chamfers only the end the thread starts from: on a stud started from its top, the
|
||
/// top is chamfered down to d3 and the bottom stays as cut. A start against a shoulder is no free
|
||
/// end and is refused; `both` there chamfers the one free end.
|
||
#[test]
|
||
fn a_tip_at_the_start_chamfers_only_that_end() {
|
||
let rf = 5.0 - 17.0 / 24.0 * 1.5 * 3f64.sqrt() / 2.0;
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 5, "height": 30, "body_name": "Stud"}));
|
||
run(&mut s, "solid.thread", json!({"face": [5, 0, 15], "designation": "M10", "tip": "start", "from": [5, 0, 30], "modeled": true}));
|
||
assert!(s.model.state().body("Stud").unwrap().body.validity().is_empty());
|
||
let want = m10_stock(0.0, 30.0, |z| 5f64.min(rf + 30.0 - z));
|
||
let got = exact_volume(&s, "Stud");
|
||
assert!((got - want).abs() < want * 1e-4, "{got} vs {want}");
|
||
let mut s = shaft_on_collar();
|
||
let e = s.execute("solid.thread", &json!({"face": [5, 0, 25], "designation": "M10", "tip": "start", "from": [5, 0, 10], "modeled": true}));
|
||
assert!(e.err().map(|e| e.to_string()).unwrap_or_default().contains("not a free end"));
|
||
run(&mut s, "solid.thread", json!({"face": [5, 0, 25], "designation": "M10", "tip": "both", "from": [5, 0, 10], "modeled": true}));
|
||
let e = s.execute("solid.thread", &json!({"face": [5, 0, 25], "designation": "M10", "tip": "chamfer", "modeled": true}));
|
||
assert!(e.err().map(|e| e.to_string()).unwrap_or_default().contains("now `both`"));
|
||
}
|
||
|
||
/// M10's groove section moved `d` out from the axis, clipped at the shaft's radius 5: the cut per
|
||
/// radian of turn, ∫ r w(r - d) dr from its moved root out to 5 (w the section's own width at
|
||
/// its radius, P/4 + 2 (ρ - root) tan 30°). A cubic in d until the root reaches the surface.
|
||
fn m10_cut_per_radian(d: f64) -> f64 {
|
||
let p = 1.5;
|
||
let root = 5.0 - 5.0 * p * 3f64.sqrt() / 16.0;
|
||
let q1 = 2.0 * (PI / 6.0).tan();
|
||
let q0 = p / 4.0 - q1 * root - q1 * d;
|
||
let a = root + d;
|
||
if a >= 5.0 {
|
||
return 0.0;
|
||
}
|
||
let f = |r: f64| q0 * r * r / 2.0 + q1 * r * r * r / 3.0;
|
||
f(5.0) - f(a)
|
||
}
|
||
|
||
/// The mean cut per radian over a runout whose offset runs linearly 0..h: Simpson on the cubic up
|
||
/// to where the root leaves the shaft (exact), nothing beyond.
|
||
fn m10_runout_mean(h: f64) -> f64 {
|
||
let p = 1.5;
|
||
let top = 5.0 * p * 3f64.sqrt() / 16.0;
|
||
let n = 64;
|
||
let step = top / n as f64;
|
||
let simpson: f64 = (0..n)
|
||
.map(|i| {
|
||
let (a, b) = (i as f64 * step, (i + 1) as f64 * step);
|
||
(m10_cut_per_radian(a) + 4.0 * m10_cut_per_radian((a + b) / 2.0) + m10_cut_per_radian(b)) * step / 6.0
|
||
})
|
||
.sum();
|
||
simpson / h
|
||
}
|
||
|
||
/// ISO 3508 runouts on a shaft between two collars: the thread starts at the lower collar and
|
||
/// its inner end fades out over 1.25 P (short) or 2.5 P (standard) before the upper one, its
|
||
/// section moving out past the surface as it turns, reaching nothing where its section clears the
|
||
/// collar. The cut is the integral over the turn of the clipped section's 2π∫ r dA (Pappus with
|
||
/// the section moving): full turns at f(0), the runout at the mean of f over the offsets it
|
||
/// passes. A fade shorter than a turn is cut too; the start never fades (`ease_in` is refused).
|
||
#[test]
|
||
fn a_runout_fades_the_groove_out_before_the_shoulder() {
|
||
let (p, w) = (1.5, ext_half_width(10.0, 1.5));
|
||
let root = 5.0 - 5.0 * p * 3f64.sqrt() / 16.0;
|
||
let h = 5.0 - root + 0.05 * p;
|
||
let turns = (35.0 - 10.0 - 2.0 * w) / p;
|
||
for (ease, r_out) in [(json!("short"), 1.25), (json!("standard"), 2.5), (json!("1 mm"), 1.0 / 1.5)] {
|
||
let mut s = shaft_on_collar();
|
||
run(&mut s, "solid.cylinder", json!({"base": [0, 0, 35], "radius": 8, "height": 10, "operation": "join", "targets": ["Part"]}));
|
||
let before = exact_volume(&s, "Part");
|
||
run(&mut s, "solid.thread", json!({"face": [5, 0, 20], "designation": "M10", "ease_out": ease, "from": [0, 0, 10], "modeled": true}));
|
||
assert!(s.model.state().body("Part").unwrap().body.validity().is_empty(), "{ease}");
|
||
let want = 2.0 * PI * (m10_cut_per_radian(0.0) * (turns - r_out) + r_out * m10_runout_mean(h));
|
||
let got = before - exact_volume(&s, "Part");
|
||
// Where the section moves, the sweep's walls lie within its tolerance (1e-4 P) of the
|
||
// true surfaces, not on them: up to that times the walls (about 64 mm² a turn) of the
|
||
// runout and of a turn more. Measured: 0.018 (short), 0.012 (standard), 0.011 mm³ (1
|
||
// mm), not growing with the runout's length; full-depth turns are exact radially.
|
||
let bound = 1e-4 * p * 64.0 * (r_out + 1.0);
|
||
assert!((got - want).abs() < bound, "{ease}: {got} vs {want}");
|
||
}
|
||
// Longer runouts than the thread are refused, and so is a runout at the start.
|
||
let mut s = shaft_on_collar();
|
||
let e = s.execute("solid.thread", &json!({"face": [5, 0, 20], "designation": "M10", "ease_out": 30, "modeled": true}));
|
||
assert!(e.err().map(|e| e.to_string()).unwrap_or_default().contains("longer than the thread"));
|
||
let e = s.execute("solid.thread", &json!({"face": [5, 0, 20], "designation": "M10", "ease_in": "standard", "modeled": true}));
|
||
assert!(e.err().map(|e| e.to_string()).unwrap_or_default().contains("`ease_in` is gone"));
|
||
}
|
||
|
||
/// A modelled M10 thread's flanks are several B-spline faces per turn (spans of one sweep); where
|
||
/// two of them meet with one tangent plane and one curvature the join is left out of the shaded
|
||
/// view (still pickable and in the wireframe), so the flank reads as one surface. The normal angle across each join is measured
|
||
/// independently (`seam_diagnostics`, projecting stations onto both surfaces).
|
||
#[test]
|
||
fn a_modelled_threads_flank_joins_are_not_drawn() {
|
||
use solidcraft_geom::brep::Surface;
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 5.0, "height": 12, "body_name": "Shaft"}));
|
||
run(&mut s, "solid.thread", json!({"face": [5.0, 0, 6.0], "designation": "M10x1.5", "modeled": true}));
|
||
let st = s.model.state();
|
||
let body = &st.body("Shaft").unwrap().body;
|
||
let mesh = body.mesh(&solidcraft_kernel::MeshTolerance::chord(0.01)).unwrap();
|
||
let record = body.record();
|
||
let free_form = |f: u32| {
|
||
record
|
||
.faces
|
||
.get(f as usize)
|
||
.is_some_and(|f| f.nurbs.is_none() && matches!(f.surface, Surface::Spline { .. } | Surface::RationalSpline { .. }))
|
||
};
|
||
let tolerances = solidcraft_kernel::ContinuityTolerances { gap_mm: 1e-3, angle_deg: 0.5, curvature_per_mm: 1.0, ..Default::default() };
|
||
let report = solidcraft_kernel::seam_diagnostics(body, &[], 33, tolerances).unwrap();
|
||
let mut flank_joins = 0;
|
||
let mut worst: f64 = 0.0;
|
||
for seam in &report.seams {
|
||
let e = seam.edge;
|
||
let uses = &record.edges[e].uses;
|
||
if uses.len() != 2 || !uses.iter().all(|u| free_form(u.face)) {
|
||
continue;
|
||
}
|
||
let angle = seam.normal_angle_deg.value;
|
||
if angle < 0.5 {
|
||
flank_joins += 1;
|
||
worst = worst.max(angle);
|
||
assert!(mesh.smooth_edges[e] && !mesh.shaded_edge_visible(e), "join {e} at {angle} deg is drawn");
|
||
assert!(mesh.edge_visible(e) && mesh.edge_pickable(e), "join {e} stays in the wireframe and pickable");
|
||
} else {
|
||
assert!(mesh.shaded_edge_visible(e), "crease {e} at {angle} deg is hidden");
|
||
}
|
||
}
|
||
// SMLib's flank pieces meet with normals about 1.5e-6 degrees apart (measured).
|
||
assert!(flank_joins >= 32 && worst < 1e-4, "{flank_joins} flank joins, the worst {worst} deg apart");
|
||
}
|
||
|
||
/// A pipe thread's profile for [`pipe_material`]: (flank half angle, thread height h, flat at crest
|
||
/// and root), each per the pitch: ISO 228-1/7-1 55° h 0.640327 P of H 0.960491 P (parallel) or
|
||
/// 0.960237 P (taper), ASME B1.20.1 60° h 0.8 P of H 0.866025 P.
|
||
fn pipe_profile(form: &str) -> (f64, f64, f64) {
|
||
let (a, big_h, h) = match form {
|
||
"bspp" | "rp" => (27.5f64, 0.960491, 0.640327),
|
||
"bspt" => (27.5, 0.960237, 0.640327),
|
||
_ => (30.0, 0.866025, 0.8),
|
||
};
|
||
(a.to_radians(), h, (big_h - h) * a.to_radians().tan())
|
||
}
|
||
|
||
/// The material a pipe thread leaves, over z0..z1, as 2π∫∫ r m dr dz with m the material
|
||
/// fraction per pitch at height y over the external thread's root, 1 - (P - flat - 2 y tan a)/P
|
||
/// (the tooth's width over the pitch), its major radius `crest(z)` (a taper's grows 1/32 per mm)
|
||
/// and the stock between `inner` and `outer`. External: full material under the root, the
|
||
/// envelope's cone taking all above the crest. Internal: the nut's teeth, crest at crest(z) - h,
|
||
/// nothing inside that (the tap's minor cone).
|
||
fn pipe_material(form: &str, p: f64, internal: bool, (z0, z1): (f64, f64), inner: f64, outer: f64, crest: impl Fn(f64) -> f64) -> f64 {
|
||
let (a, h, flat) = pipe_profile(form);
|
||
let (h, flat) = (h * p, flat * p);
|
||
let tooth = |y: f64| ((p - flat) * p.recip() - 2.0 * y * a.tan() / p).clamp(0.0, 1.0);
|
||
let (nz, nr) = (4000, 400);
|
||
let mut v = 0.0;
|
||
for i in 0..nz {
|
||
let z = z0 + (z1 - z0) * (i as f64 + 0.5) / nz as f64;
|
||
let rc = crest(z);
|
||
let (root, top) = if internal { (rc, rc - h) } else { (rc - h, rc) };
|
||
let mut ring = 0.0;
|
||
// Exactly the full annuli, the band in fine steps.
|
||
let (b0, b1) = (root.min(top).clamp(inner, outer), root.max(top).clamp(inner, outer));
|
||
if internal {
|
||
ring += (outer * outer - b1 * b1) / 2.0;
|
||
} else {
|
||
ring += (b0 * b0 - inner * inner) / 2.0;
|
||
}
|
||
for j in 0..nr {
|
||
let r = b0 + (b1 - b0) * (j as f64 + 0.5) / nr as f64;
|
||
let y = if internal { root - r } else { r - root };
|
||
ring += r * tooth(y) * (b1 - b0) / nr as f64;
|
||
}
|
||
v += 2.0 * PI * ring * (z1 - z0) / nz as f64;
|
||
}
|
||
v
|
||
}
|
||
|
||
/// ISO 7-1 and ASME B1.20.1 taper threads, ISO 228-1 parallel: an R 1/2 and a 1/2-14 NPT on pipe
|
||
/// stubs of their pipes' outside diameters (21.3 mm, 0.840 in), an Rc 1/2 through a plate and a
|
||
/// G 1/2, each cut from the top across the whole face (a free end past each end, so every
|
||
/// meridian half-plane averages the same profile). The taper puts the external thread's gauge
|
||
/// diameter its gauge length in from the small end (R 1/2: 20.955 at 8.2 mm; NPT: E1 + h at L1)
|
||
/// and the internal one's at its face.
|
||
#[test]
|
||
fn pipe_threads_cut_their_standard_profiles_and_tapers() {
|
||
let inch = 25.4;
|
||
// (designation, form, internal, stock radius, crest radius at z for a 12 mm stock threaded from z = 12)
|
||
let r_half: f64 = 20.955 / 2.0 - 8.2 / 32.0;
|
||
let npt_half: f64 = ((0.75843 + 0.32 / 16.0) + 0.8 / 14.0) * inch / 2.0 - 0.32 * inch / 32.0;
|
||
// ISO 7-1's Rp, parallel and internal, in a hole drilled to its minor diameter.
|
||
let rp_minor = 20.955 / 2.0 - 0.640327 * inch / 14.0;
|
||
let cases: [(&str, &str, bool, f64, Box<dyn Fn(f64) -> f64>); 5] = [
|
||
("R 1/2", "bspt", false, 10.65, Box::new(move |z| r_half + (12.0 - z) / 32.0)),
|
||
("1/2-14 NPT", "npt", false, 0.42 * inch, Box::new(move |z| npt_half + (12.0 - z) / 32.0)),
|
||
("G 1/2", "bspp", false, 20.955 / 2.0, Box::new(|_| 20.955 / 2.0)),
|
||
("Rc 1/2", "bspt", true, 9.2, Box::new(|z| 20.955 / 2.0 - (12.0 - z) / 32.0)),
|
||
("Rp 1/2", "rp", true, rp_minor + 1e-4, Box::new(|_| 20.955 / 2.0)),
|
||
];
|
||
for (designation, form, internal, rs, crest) in cases {
|
||
let stock = || {
|
||
let mut s = Session::default();
|
||
if internal {
|
||
run(&mut s, "solid.box", json!({"corner": [-20, -20, 0], "length": 40, "width": 40, "height": 12, "body_name": "Part"}));
|
||
run(&mut s, "solid.cylinder", json!({"base": [0, 0, -1], "radius": rs, "height": 14, "body_name": "Bore"}));
|
||
run(&mut s, "solid.combine", json!({"target": "Part", "tools": ["Bore"], "operation": "cut"}));
|
||
} else {
|
||
run(&mut s, "solid.cylinder", json!({"radius": rs, "height": 12, "body_name": "Part"}));
|
||
}
|
||
s
|
||
};
|
||
let face = [rs, 0.0, 6.0];
|
||
let (mut s, mut cosmetic) = (stock(), stock());
|
||
let out = run(&mut cosmetic, "solid.thread", json!({"face": face, "designation": designation, "from": [rs, 0, 12], "length": 12}));
|
||
assert_eq!(out["thread"]["designation"], json!(designation));
|
||
run(&mut s, "solid.thread", json!({"face": face, "designation": designation, "modeled": true, "from": [rs, 0, 12], "length": 12}));
|
||
let st = s.model.state();
|
||
assert!(st.body("Part").unwrap().body.validity().is_empty(), "{designation}");
|
||
let p = inch / 14.0;
|
||
let got = exact_volume(&s, "Part");
|
||
let (want, stock) = if internal {
|
||
let plate = 40.0 * 40.0 * 12.0;
|
||
let hole = PI * rs * rs * 12.0;
|
||
(plate - hole - (PI * (30.0 * 30.0 - rs * rs) * 12.0 - pipe_material(form, p, true, (0.0, 12.0), rs, 30.0, &crest)), plate - hole)
|
||
} else {
|
||
(pipe_material(form, p, false, (0.0, 12.0), 0.0, rs, &crest), PI * rs * rs * 12.0)
|
||
};
|
||
// A parallel thread's meridians are alike exactly. A taper's section moves off the axis
|
||
// as it turns, so the meridians differ; the averaged profile met the cut within 0.12 % of
|
||
// the removed volume here (R 1/2 0.06 %, NPT 0.12 %).
|
||
let tol = if matches!(form, "bspp" | "rp") { 1e-5 } else { 2e-3 };
|
||
assert!((got - want).abs() < (stock - want).abs() * tol, "{designation}: {got} vs {want} (stock {stock})");
|
||
}
|
||
}
|
||
|
||
/// A taper pipe thread's rules: it starts at a free end (not at a shoulder), ISO 7-1 names the
|
||
/// internal taper Rc and the external R (and Rp is internal only), a pipe thread has one start and
|
||
/// turns one way, and its chamfered tip is cut from the small end's major diameter.
|
||
#[test]
|
||
fn a_taper_pipe_thread_starts_at_a_free_end_and_is_named_for_its_side() {
|
||
let part = || {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.cylinder", json!({"radius": 16, "height": 10, "body_name": "Part"}));
|
||
run(&mut s, "solid.cylinder", json!({"base": [0, 0, 10], "radius": 10.65, "height": 25, "operation": "join", "targets": ["Part"]}));
|
||
s
|
||
};
|
||
let mut s = part();
|
||
let err = |s: &mut Session, p: Value| s.execute("solid.thread", &p).err().map(|e| e.to_string()).unwrap_or_default();
|
||
let e = err(&mut s, json!({"face": [10.65, 0, 20], "designation": "R 1/2", "modeled": true, "from": [10.65, 0, 10]}));
|
||
assert!(e.contains("starts at a free end"), "{e}");
|
||
let e = err(&mut s, json!({"face": [10.65, 0, 20], "designation": "Rc 1/2", "modeled": true, "from": [10.65, 0, 35]}));
|
||
assert!(e.contains("an external taper thread is R"), "{e}");
|
||
let e = err(&mut s, json!({"face": [10.65, 0, 20], "designation": "R 1/2", "starts": 2, "modeled": true}));
|
||
assert!(e.contains("one start"), "{e}");
|
||
let e = err(&mut s, json!({"face": [10.65, 0, 20], "designation": "R 1/2", "hand": "both", "modeled": true, "from": [10.65, 0, 35]}));
|
||
assert!(e.contains("turns one way"), "{e}");
|
||
let e = err(&mut s, json!({"face": [10.65, 0, 20], "designation": "Rp 1/2", "modeled": true, "from": [10.65, 0, 35]}));
|
||
assert!(e.contains("Rp is an internal thread"), "{e}");
|
||
// ISO 4753's chamfered end is metric: a pipe thread gives its depth.
|
||
let e = err(&mut s, json!({"face": [10.65, 0, 20], "designation": "R 1/2", "tip": "start", "modeled": true, "from": [10.65, 0, 35]}));
|
||
assert!(e.contains("chamfer depth"), "{e}");
|
||
// From the free end it runs ISO 7-1's useful thread, 13.2 mm for R 1/2.
|
||
let out = run(&mut s, "solid.thread", json!({"face": [10.65, 0, 20], "designation": "R 1/2", "from": [10.65, 0, 35]}));
|
||
let t = &out["thread"];
|
||
assert!((t["end"].as_f64().unwrap() - t["start"].as_f64().unwrap() - 13.2).abs() < 1e-9, "{t}");
|
||
let mut plain = part();
|
||
run(&mut plain, "solid.thread", json!({"face": [10.65, 0, 20], "designation": "R 1/2", "modeled": true, "from": [10.65, 0, 35]}));
|
||
assert!(plain.model.state().body("Part").unwrap().body.validity().is_empty());
|
||
// The chamfered tip of a taper thread: the cone reaches the small end's major diameter less
|
||
// the depth, and cuts the first teeth.
|
||
let p = 25.4 / 14.0;
|
||
run(
|
||
&mut s,
|
||
"solid.thread",
|
||
json!({"face": [10.65, 0, 20], "designation": "R 1/2", "modeled": true, "from": [10.65, 0, 35], "tip": "start", "chamfer_depth": 0.640327 * p}),
|
||
);
|
||
assert!(s.model.state().body("Part").unwrap().body.validity().is_empty());
|
||
let (chamfered, threaded) = (exact_volume(&s, "Part"), exact_volume(&plain, "Part"));
|
||
assert!(chamfered < threaded - 1e-3, "the tip cuts the first teeth: {chamfered} vs {threaded}");
|
||
}
|
||
|
||
/// A tapped hole's thread cut into its wall (`modeled`), as the thread feature cuts one: an M8
|
||
/// blind hole whose groove stops clear of the drill point's bottom, or fades out before it
|
||
/// (`ease_out`, ISO 3508), which leaves more of the wall than the full form there; an Rc 1/2
|
||
/// through a plate, drilled with the tap maker's drill and cut to its taper; each a valid body
|
||
/// that reopens the same. An Rc size with no tabulated drill is refused.
|
||
#[test]
|
||
fn a_modelled_tapped_hole_stops_clear_of_its_bottom_or_fades_out_before_it() {
|
||
let blind = |extra: Value| {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length":30,"width":30,"height":20,"body_name":"Plate"}));
|
||
let mut p = json!({"position":[15,15,20],"direction":[0,0,-1],"thread":"M8","depth":14,"type":"drilled"});
|
||
for (k, v) in extra.as_object().unwrap() {
|
||
p[k] = v.clone();
|
||
}
|
||
run(&mut s, "solid.hole", p);
|
||
assert!(s.model.state().body("Plate").unwrap().body.validity().is_empty(), "{extra}");
|
||
s
|
||
};
|
||
let (drilled, square, fade) = (blind(json!({})), blind(json!({"modeled":true})), blind(json!({"modeled":true,"ease_out":"standard"})));
|
||
let (v0, v1, v2) = (exact_volume(&drilled, "Plate"), exact_volume(&square, "Plate"), exact_volume(&fade, "Plate"));
|
||
assert!(v1 < v2 && v2 < v0, "drilled {v0}, square {v1}, fade {v2}");
|
||
// The groove never reaches the drill point: the bottom's cone is the drilled one.
|
||
assert!(square.model.state().threads.is_empty(), "a modelled thread is cut, not listed");
|
||
let reopened = Session::new(solidcraft_doc::Document::from_json(&fade.doc.to_json()).unwrap());
|
||
assert!((exact_volume(&reopened, "Plate") - v2).abs() < 1e-6);
|
||
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length":40,"width":40,"height":12,"body_name":"Plate"}));
|
||
let out = run(&mut s, "solid.hole", json!({"position":[20,20,12],"direction":[0,0,-1],"thread":"Rc 1/2"}));
|
||
let drilled = exact_volume(&s, "Plate");
|
||
// The tap maker's drill for a straight Rc 1/2 hole (Yamawa YEU23 p.709).
|
||
let drill: f64 = 17.6;
|
||
assert!((drilled - (40.0 * 40.0 * 12.0 - PI * (drill / 2.0).powi(2) * 12.0)).abs() < 1e-3, "{drilled}");
|
||
let id = out["feature"].as_u64().unwrap();
|
||
let redefine = json!({"position":[20,20,12],"direction":[0,0,-1],"thread":"Rc 1/2","modeled":true});
|
||
run(&mut s, "timeline.redefine", json!({"feature":id,"command":"solid.hole","params":redefine}));
|
||
assert!(s.model.state().body("Plate").unwrap().body.validity().is_empty());
|
||
assert!(exact_volume(&s, "Plate") < drilled - 1.0);
|
||
|
||
let err = |p: Value| Session::default().execute("solid.hole", &p).err().map(|e| e.to_string()).unwrap_or_default();
|
||
assert!(err(json!({"position":[0,0,0],"diameter":5,"modeled":true})).contains("`modeled` needs `thread`"));
|
||
assert!(err(json!({"position":[0,0,0],"thread":"M8","ease_out":"standard"})).contains("modelled thread"));
|
||
assert!(err(json!({"position":[0,0,0],"thread":"Rc 5"})).contains("no tap drill is tabulated"));
|
||
// Another drill than the tap maker's (M8: 6.8 mm): from the minor diameter to 5% over it.
|
||
let drill = |d: f64| {
|
||
let mut s = Session::default();
|
||
run(&mut s, "solid.box", json!({"length":30,"width":30,"height":20,"body_name":"Plate"}));
|
||
s.execute("solid.hole", &json!({"position":[15,15,20],"thread":"M8","diameter":d})).err().map(|e| e.to_string()).unwrap_or_default()
|
||
};
|
||
let e = drill(7.5);
|
||
assert!(e.contains("from 6.647 to 7.14 mm") && e.contains("too little of the thread"), "{e}");
|
||
assert!(drill(6.5).contains("the tap cannot cut"));
|
||
assert!(drill(7.1).is_empty() && drill(6.7).is_empty(), "inside the range");
|
||
}
|