Files
solidcraft/tests/kernel-cases/fillets/KNOWN_FAILING
T
jyvikoandClaude Opus 5.5 f3b77d71b3 Tests: expectations for the SMLib fixes of 2026-10-29
With SMLib integration-overnight + b78bd4a (the fixes of 2026-10-29), three
expectations that held a refusal now build, each checked against its exact answer:

- rig fillets/1207-fillet-box-end-edge-into-unblended-round (was ...-refused): the end
  face's top edge of a cube rounded r3 along its top back edge, rounded r1 alone
  (tangent chain off), builds. Its round runs on along y through the r3 round's end
  until that surface drops below it at y = 17 + sqrt(5): V = 8000 - 20 (9 - 9 pi/4)
  - 17 (1 - pi/4) - 0.218236 = 7957.505202 (the last term the section under the round,
  integrated exactly); SMLib gives 7957.505245.
- blend_smlib smooth_edges_and_unfinished_tangent_chains_are_refused_saying_why: the
  same cube builds, at that volume.
- modify_history_tests::smlib::draft_tilts_a_side_and_keeps_its_name: the rod's side,
  a cylinder along the pull, drafts 5 deg to a frustum, radius 5 at the neutral plane
  and 5 - 10 tan 5 deg at the top, at its exact volume.

tests/kernel-cases/fillets/KNOWN_FAILING drops 1557-fillet-vertical-corners-after-
bottom-rounds, which passes now; the other eight still fail, so the gate holds
(81 pass, 8 known failing, no regression).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 19:03:36 -04:00

13 lines
1.4 KiB
Plaintext

# The fillet cases that fail today, one a line: `<case> <why it fails today>`. Sorted. The fillet
# rig gate (.github/workflows/fillet-rig.yml) fails on a case that fails and is not listed here,
# and on a listed case that passes: a fix removes its line in the same pull request.
# Baseline: develop 242bbc89f with the SMLib fixes of 2026-10-29 (integration-overnight + b78bd4a), aarch64 Linux.
1207-fillet-bar-top-edge-after-boss-arc-round-r0-5 SMLib's check refuses the round: internal coincident control points in a B-spline curve (an internal pole)
4782-fillet-bar-edge-wider-than-both-faces SMLib status 1001: a convex round past both its faces is not yet built by subtraction
4782-fillet-two-end-verticals-past-a-full-round SMLib's result is not a closed solid, where a refusal naming 7.5 mm (fillet_max for the exact fit) is right
5158-fillet-round-just-past-a-10mm-face SMLib status 1001: a convex round 0.01 past its face is not yet built by subtraction (10.0001-10.04 open)
9-fillet-corner-curvature-with-reduce-fit not supported yet: solid.fillet builds corner g2 with the exact fit only
9-fillet-corner-curvature-with-taper-fit not supported yet: solid.fillet builds corner g2 with the exact fit only
9-fillet-corner-r1-curvature-default-setback continuity g1: the g2 corner patch seams G1 at the corner point, not G2
9-fillet-corner-r5-curvature-default-setback continuity g1: the g2 corner patch seams G1 at the corner point, not G2