Commit Graph
146 Commits
Author SHA1 Message Date
jyvikoandClaude Opus 5.5 ffd3d5fb18 Kernel rig: construction cases, an axis on a straight box edge, and a circular edge refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 5c0db8e825 Kernel rig: the construction area, with what reruns it
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 70f695c6ba Kernel rig: grade construction geometry and the numbers a command replies with
A case's construction field names construction points, axes and planes with the point, line or
plane each must be, and results reads values out of the commands' own replies by JSON pointer.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 b8c6bb9214 Kernel rig: thicken a sheet into a slab and a tube, trim by a plane and by a circle, and refuse a stray keep_with
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 75353cb042 Kernel rig: extend, extrude, loft, patch, revolve, stitch and sweep surfaces, a normal case and an edge case each, with their exact areas and surface kinds
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 3d080e96a3 Kernel rig: fairing leaves a flat patch flat and a face with no free control rows as it was; zero strength is refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 f861f44e1d Kernel rig: a matched sheet meets its target's edge at the order asked, flat where both are flat, and a solid is refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 425c8ed421 Kernel rig: a blend between coplanar sheets is flat, a step blend meets both sheets at the order asked, and unchained edges are refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 680f2ee5cb Kernel rig: boundary surfaces through a square, a triangle and a network of four lines have their exact areas; five curves are refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 7ac95e47e8 Kernel rig: a reversed normal sends a later thicken to the other side, and a solid is refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 b2cc77094c Kernel rig: unstitch takes a box and a cylinder apart into their faces, or one face out, and refuses a single face
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 a01d82f304 Kernel rig: untrim removes holes from a sheet, a cylinder sheet and a solid's face, and refuses a face with none
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 476b04ed33 Kernel rig: ruled strips along a normal, at 45 degrees and tangent are the exact plane, cone and flat ring, and a closed chain mitres into a frame
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 657c5af579 Kernel rig: surfaces area; an offset plane, cylinder and sphere land exactly where the distance puts them, and faces across a sharp edge part
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 5ba60bd9d3 Kernel rig: plastic cases, bosses, lips and grooves, rests, a snap fit edge case and the plastic rules, each with its answer
A new plastic area with its KNOWN_FAILING (empty: every case passes) and the
sources whose change reruns it; the README lists the area and the new files and
results fields.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 67dd8892f1 Kernel rig: bend table cases, JSON and CSV rows with angles, radii and K-factor allowances, and an unknown format refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 c114e6c35b Kernel rig: flat DXF cases, outline, cut and bend line lengths, an ellipse exact and as arcs, and no sheet refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 fce8e4a262 Kernel rig: perforation cases, square and staggered fields counted hole by hole, a field kept clear of a bend zone, and a pitch refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 c60bcb55e1 Kernel rig: path flange cases, a Z section, one line at 45 degrees down, and a path straight on refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 2edf649528 Kernel rig: hem cases, closed on a top and a bottom edge, open and flipped, on a flange, and one too short
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 acd7bb066d Kernel rig: the boundary-fill crescent ends at the cusps, x = 5
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 815711421e Kernel rig: second cases for draft (two adjacent faces), rib (in plane), press pull (an edge), split face (sketch and tool face) and sketch projection (a face loop and a silhouette)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 4e7810659b Kernel rig: frames area, frame member and inserted profile cases with their exact sections, placements and a too-thick wall refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 1e9cefe1e8 Kernel rig: web cases, two gussets in a channel's corners and two walls grown along the sketch normal
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 f0eac58a2c Kernel rig: align cases, face onto face as a move, a side face turned onto a top face, and a face onto an offset plane along its normal
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 a5513a4e17 Kernel rig: boundary fill cases, the lens and the crescent of two cylinders, and a point outside every tool refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 be4f15db63 Kernel rig: bounding solid cases, two boxes with a margin and a sphere's exact box
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 cf58e37359 Kernel rig: replace face cases, a top moved onto a plane and a lower step raised to the higher top (fails today: SMLib offset of faces refuses closing the step wall)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 e1724be629 Kernel rig: pattern on path cases, bosses along a line, bodies turning with an arc's tangent, and instances past the path's end refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 af8f28e343 Kernel rig: scale cases, a cube doubled about its corner, a sphere scaled into an ellipsoid of the same volume, and a zero factor refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 585789c606 Kernel rig: cone cases, a frustum on X and a full cone of negative height with their exact volume, area and centroid, and a zero height refused; a new solids area
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 6701b1c5e0 Docs: how the kernel rig picks its areas, how a new area joins, and the coverage check
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 d671bbbc12 Kernel rig: every registry command has a case or an exemption (kernel-cases --coverage)
cargo xtask kernel-cases --coverage lists every built registry command that no recipe.json under
tests/kernel-cases runs and fails unless tests/kernel-cases/EXEMPT lists it. EXEMPT holds 252
commands with no geometry to grade and, under [to cover], 133 geometry commands still waiting for
a case; a listed command a case now uses, or one the registry no longer has, fails the check, so
the to-cover section only shrinks. The gate's build job runs it.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 b67e93211d Kernel rig: an area's PATHS names only its own files, never the shared core
The booleans area also reruns on sketch projection from the model. The selection self-test
fails on an area glob that matches a file PATHS-ALL already covers, so a whole-crate glob
cannot creep in.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 02e1f18412 Kernel rig: each area runs only when the files its PATHS lists change, every area on the shared core
A plan job (scripts/ci/kernel_rig_plan.py, with its self-test) maps a pull request's changed files
to the areas: tests/kernel-cases/<area>/PATHS for each area, tests/kernel-cases/PATHS-ALL for the
shared core, the ladder whenever any area runs. Areas come from the folders, so a new one needs no
workflow edit. Pushes, merge groups, the release gate and runs by hand run every area. The
kernel-rig check counts a skipped build or shard as passed only when the plan selected none.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 e711777699 Docs: the kernel rig gate, updating a known-failing list, re-recording the ladder golden
tests/kernel-cases/README.md describes the kernel rig gate for every area, how a pull request
updates its area's KNOWN_FAILING, and the ladder's --gate and --record. The tests skill and
CONTRIBUTING say which pull requests run the native and reference tests, and what the
release gate runs.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 b4fcd59100 Kernel rig: every area and the ladder as a parallel gate on pull requests that touch the kernel
kernel-rig.yml builds solidcraft-cli once (release, SMLib prebuilt; sccache on a sticky disk
that only pushes to main and develop commit) and hands it, with the rig's runner, to a matrix
of eleven shards: the ten areas of tests/kernel-cases/, each against its KNOWN_FAILING, and
the ladder against its golden. One path filter covers the kernel surface; drafts skip; a new
push cancels a pull request's old run; merge groups always run it, and the release gate calls
it. The areas other than fillets get a KNOWN_FAILING with only its header, to be seeded from
develop after the SMLib pin bump.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 9008d13f31 Surface Extrude: a symmetric distance is the total, as for a solid extrude
A symmetric surface.extrude given no convention now splits its distance
evenly around the start plane (10 mm: 5 mm each side), the way
solid.extrude reads it, instead of going the distance each way. Both
commands take their default from one function, which a session setting
(surface_extrude_symmetric_per_side) can turn back to the per-side
reading for surface extrudes. timeline.edit and timeline.redefine give a
one-sided surface extrude made symmetric the same default.

Saved designs are unchanged: every surface extrude saved its convention
(legacy_per_side), and one saved before the marker existed reads per side
as it always did. The help of both commands says how the distance is
read. The 3830 kernel case, recorded with the per-side reading, now says
so explicitly.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 19:09:59 -04:00
jyvikoandClaude Opus 5.5 f3b77d71b3 Tests: expectations for the SMLib fixes of 2026-10-29
With SMLib integration-overnight + b78bd4a (the fixes of 2026-10-29), three
expectations that held a refusal now build, each checked against its exact answer:

- rig fillets/1207-fillet-box-end-edge-into-unblended-round (was ...-refused): the end
  face's top edge of a cube rounded r3 along its top back edge, rounded r1 alone
  (tangent chain off), builds. Its round runs on along y through the r3 round's end
  until that surface drops below it at y = 17 + sqrt(5): V = 8000 - 20 (9 - 9 pi/4)
  - 17 (1 - pi/4) - 0.218236 = 7957.505202 (the last term the section under the round,
  integrated exactly); SMLib gives 7957.505245.
- blend_smlib smooth_edges_and_unfinished_tangent_chains_are_refused_saying_why: the
  same cube builds, at that volume.
- modify_history_tests::smlib::draft_tilts_a_side_and_keeps_its_name: the rod's side,
  a cylinder along the pull, drafts 5 deg to a frustum, radius 5 at the neutral plane
  and 5 - 10 tan 5 deg at the top, at its exact volume.

tests/kernel-cases/fillets/KNOWN_FAILING drops 1557-fillet-vertical-corners-after-
bottom-rounds, which passes now; the other eight still fail, so the gate holds
(81 pass, 8 known failing, no regression).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 19:03:36 -04:00
jyvikoandClaude Opus 5.5 242bbc89f0 Fillet rig: the known-failing list follows the SMLib 7e917f0 pin
Ten cases the pin fixed leave the list (the 1207 corner patch and its together cases, 1390,
4782 reduce-fit, 896). 1557 joins it with its cause: since bodies are read back from their
records (#8625) its bottom rounds come back as SmCylinder where SMLib's blend made SmCone(0),
and the corner-ball trace starts 2.78e-4 off; its fix is in progress.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 07:14:45 -04:00
jyvikoandClaude Opus 5.5 102cde292c Kernel rig: patched holes graded by their continuity, at clashing corners and in one sheet
Four continuity cases for the patch fill. A hole in one smooth sheet (a cubic Bezier profile
extruded, a square trimmed out) patched g2 and g3: every seam reaches the order, corners
included, since round the hole there is one surface. The hole a three-round corner's blend
face leaves, patched g2 and g3: exactly g1 over each whole seam, since at the hole's corners
the rounds meet each other G1 (their curvatures differ by 1/4 or 1/8 per mm) and a patch smooth
there has one curvature; the middle of each seam reaches the order (kernel test).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 00:30:03 -04:00
jyvikoandClaude Opus 5.5 517fc01dcf Fillet rig: a regression gate on every pull request that touches fillet code
cargo xtask kernel-cases --known-failing FILE grades a set against its
baseline: it fails on a case that fails and is not listed (a regression)
and on a listed case that passes (fixed: its line goes, so the list only
shrinks). The Fillet rig workflow runs the fillet set that way on pull
requests touching the blend, fillet, corner and continuity kernel files,
crates/smlib, eval*.rs, engine features.rs or the cases: one release
build of solidcraft-cli on a Blacksmith runner, SMLib prebuilt, sccache
on a sticky disk that main and develop commit.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 21:23:24 -04:00
jyvikoandClaude Opus 5.5 52339b7ec3 Kernel rig: fillet cases for the open fillet issues, each with its exact answer
New: an r5 curvature corner at a box corner (its patch must seam G2), an
edge running tangentially into a round left out (refused: continues
tangentially), a convex r10.01 round 0.01 past a 10 mm face (built by
subtraction: V = 7139.875, A = 2585.140). The bar and boss arc rounded
together say their crease (15.6 deg r2, 13.1 deg r1); 1390 expects SMLib's
unsupported-corner refusal, the honest reason today; past a full round
the exact fit's refusal names the largest radius that fits, 7.5 mm.

KNOWN_FAILING lists the 18 of 89 fillet cases failing today, each with
its cause.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 21:23:24 -04:00
jyvikoandClaude Opus 5.5 39bf63b16a Kernel rig: designed continuity cases, G0 to G4, that prove the measurement
A new `continuity` area: seams whose order is certain by construction, each graded
`exact` (reads its order and not the next) at picked edges with Continuity Analysis's
default stations and tolerances: a box's crease (g0), a chamfer in place of a round (g0),
an r5 round on planes (g1), and a profile closed by a g1, g2, g3 or g4 blend curve between
lines, extruded (g1 … g4). `continuity.edges` may now be a list of points, picked as
`inspect.continuity` picks them, and `continuity.exact` asks for the order and no more.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 21:22:17 -04:00
jyvikoandClaude Opus 5.5 c37b0d2f02 Kernel rig: a case's expected continuity order at its blend seams
expected.json may give `continuity: {order: g0…g4, edges?: "blend" | "corner"}`: the
seams of each round, chamfer face or corner patch with the faces either side of the edge it
replaced, and of each corner patch with its rounds, are measured as Continuity Analysis
measures them (seam_diagnostics at its default 33 stations and default tolerances), and the
case fails naming the worst seam, its faces, the order it reaches and the next order's worst
value. The seams come from the faces' persistent names (doc::naming::blend_seams). The older
`{near, within_mm, …}` form is kept.

Every fillet-area case with a body gets its order: constant rounds and rolling corners g1,
curvature rounds g2, chamfers g0, the corner: g2 patch g2 at its seams.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 21:22:17 -04:00
jyvikoandClaude Opus 5.5 cfaf4ab557 Kernel rig: the reason each refused sheet-metal, sweep, crash and ladder case must be refused for
Ten `refused` cases outside the fillets had no `refusal` since #8445 made one required. Each
was run; its refusal is the right answer for the reason its method gives, and that reason is
now its `refusal`.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 16:59:05 -04:00
jyvikoandClaude Opus 5.5 97721ad05f Fillet setbacks not past where the rounds meet are refused naming the least; the rig grades a refusal by its reason
A corner setback must reach past where the corner's rounds' contact lines
meet without one (smlib_blend_setback); short of it SMLib failed with its
own status (1001). The kernel now refuses it before SMLib runs, for the
rolling-ball corner (fillet_setback) and the curvature corner
(fillet_g2_corners) alike, naming the least: on each face at a corner of
planar faces and straight edges the two rails, r tan(psi/2) from their
edges, cross (d2 + d1 cos alpha) / sin alpha along an edge (r on faces
square to each other). Other corners stay SMLib's to refuse.

The rig's `refused` cases now name the reason (`refusal`, a part of the
message, required), so a failure for another reason no longer passes; a
`solid_or_refused` case may name one. Fillets: the setback cases and
783, 3435 pass; 1390, 896, 4782 past-a-full-round and the no-tangent-chain
case are refused for an unclear reason and fail.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 15:13:23 -04:00
jyvikoandClaude Opus 5.5 762262953f kernel rig: the owner's fillet failures of 2026-10-28 as fillet cases, with the option combinations
22 hand-written cases in tests/kernel-cases/fillets:
- 1207-fillet-bar-top-edge-and-boss-arc-together (r2, r1, fit reduce,
  fit taper, curvature corners): a bar's top edge and the partial base
  arc of a boss standing out over the bar's side rounded together. The
  rounds' volumes away from the corner, the corner patch within (2r)^3.
  SMLib's 3x2 mixed corner fails here (1001) until the fork's fix.
- 1207-fillet-bar-top-edge-after-boss-arc-round (r2, r0.5, no tangent
  chain): the edge rounded after the arc; r0.5 fails SMLib's check.
- 9-fillet-corner-*: setbacks not past the radius refused (rolling and
  curvature corners), the curvature corner at r1, and the curvature
  corner with reduce and taper fits (not supported yet).
- 4782-fillet-*: full rounds (two end verticals at half the width, exact,
  reduce, taper), a round at half the wall, radii past the full round
  (refused; reduce gives the full round) and a round wider than both
  faces (built by subtraction).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 15:13:23 -04:00
jyvikoandClaude Opus 5.5 05f1c6b9ac Tapped holes: the tap maker's drill for every form, and a drill of the user's within 5%
Every tapped hole now drills the tap maker's tabulated drill. ISO metric takes Yamawa YEU23's
drill size column for cutting taps (printed p.704, M coarse; pp.704 to 706, MF fine): M8 drills
6.8 mm and M12 10.3 mm, where the major less the pitch gave 6.75 and 10.25. A custom metric size
the table lacks keeps the major less the pitch. UNC/UNF (Guhring), G, Rp, Rc and NPT (Yamawa)
were tabulated already. The Thread command's suggested hole for a metric size follows.

The Hole dialog's Tap drill diameter is now a field, the tap maker's drill by default, and the
command's `diameter` with a thread is checked the same way: a drill is accepted from the
internal thread's standard minor diameter (or the tap maker's drill where that lies below it:
Rp, Rc, NPT) to 5% over the tap maker's drill. Outside that the command names the range and
why. The field's tooltip gives the drill, the minor diameter and the range. Presets keep a
chosen drill.

A saved design keeps the diameter it stored, so it builds as before, and editing such a hole
keeps its drill: no preference and no format change. Scripts that give a thread without a
diameter drill the new default; ladder 05/007, 11/003 and rig case threads/2115 follow
analytically, and their golden entries are re-measured from runs (tier 05 re-sorted by time).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 72e0e00940 Ladder 06/017: the golden entry from a run of the case
Ladder 06/017's golden entry was edited by hand when the chamfered tip moved to ISO 724's d3.
Re-measured by running the case (solidcraft-cli kernel-cases on SMLib): its counts, area and
volume are the ones written by hand; its time is the run's. The tier's order by time holds.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00