A square cut is the slanted plane's ordinary crossing; the cam's half turn is the quarter turn's
contact at a symmetric angle; the r15 slab stands inside the same coincidence tolerance as the r10;
the 90 degree unfold and the 40 degree flange repeat the 72 degree and 20 degree cases' formulas.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The sloped-basin chamfers and rounds at 0.5 mm rims repeat the 1 mm rim's regimes; two of the
three knife-edge chamfer tips, the r1 and box r3 curvature corners, the r1 tangent corner, the
1 mm pocket-rim and hole-rim chamfers short of the floor and the r1 together-round each repeat a kept case's regime
and grades. #854 moves to 851-chamfer-arc-top-edge-9-5, and the cases that cited a dropped one
cite the kept one or state its formula.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The ring cut frame's and the up-down join's shells build now, and so do the up-down join's and
modern-plastic's chamfers (SMLib smlib-blend-refusals). #616's lid in the corpus still fails
SMLib's loop check, the shelled box shelled again at an inner wall is unchanged, and the
oblique cut of a cylinder's fillet still fails SmSurfOfRevolution's Test #7: 3 actions of 7.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib keeps the skirt top's offset where its loops wind the other way under the opening, the
cavity's floor (the owner's ruling of 2026-10-31: build it; a lip thinner than the wall is no
break-through).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's inset now keeps only the regions that are cavity, not the one the offsets close where
they overlap (between the two faces of #545's 0.5 floor, round the up-down join's two empty
octants). The frame's core under the recess is hollowed to a sealed void, so the case says two
shells and its closed form, 21044 mm³.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's merge now intersects the offsets of an edge's faces where they could not be mated along
it (the hole's offset poking out through the half-round side's; tangency-labs/solidcore#1795):
one closed valid solid with the one face open, as the owner ruled.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib now offsets a vertex where four faces meet (two walls and two facets at the floor's
corners, four facets at the drain) to two vertices joined by a new edge (tangency-labs/smlib
branch smlib-shells). Both volumes match their closed forms. The pocket's lining, hanging from
the top's rim round the pocket, stands apart from the slab's outer walls with the cavity rising
between them to the open top: the case says two shells in the one body.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
926 (the chamfer ending on the boss's wall), the oblique cut's r0.1
round, the every-block r1 round (its seam with the cylinder is no
contact seam, after the blend_seams fix), the up-down squares' concave
chamfers and the shelled box's lip chamfer build with SMLib branch
smlib-blend-refusals (f8650b8 and later). 1207 r0.5 passes SMLib's check
on its rails now and stays listed for the next cause: its end rib on the
boss, which starts where the round and the boss are tangent.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's ruling: a round or chamfer that runs past an outer edge of its face into open air
builds, tangent where it has room and cut by the face beyond where it runs out. SMLib's branch
smlib-blends-past-rims builds them by the rig's analytic answers. Off the known-failing list:
the disc's rim past its 2 mm wall (190), the hole's top rim R12 past the plate's bottom, the
chamfer past the cylinder's bottom (2893), each closing on the wall continued as itself, and
926's chamfer ending on the boss's wall, which now builds to its answer too.
The sloped basins' R4 rim rounds (1080, mitred rounds built together where one overflows) build
to their analytic volumes (to 6e-9), and stay listed with that reason: their continuity check
(g1 at every blend seam) takes in the mitres' creases, G0 by the mitre ruling.
2893-chamfer-two-distances-elliptical-rim is graded as a solid (the owner: it builds) and stays
listed, waiting on the ruling on unequal chamfers along a rim whose angle varies.
5158-fillet-round-just-past-a-10mm-face stays listed with its cause found: the round passes
5e-6 under the box's top back edge, inside the body's tolerance.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A projected spline edge of several Bezier spans came into the sketch as one
curve per span (#1508), so a G2 round's bottom edge was 16 curves and a path
naming the corner named one span of it (#3604). The kernel now reads such an
edge (a spline, or an elliptical arc of several spans) as the one clamped
B-spline it is over the edge's interval, its knots and weights its own, and
the sketch takes it as one control spline whose ends sit on the edge's
vertices. Planar regions still read edges span by span. The 3604 case builds
with its original path and leaves KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A face tool cut with that face's surface alone, so a face of a surface body made of spans joined
tangent (a fit-point spline extruded, #3830) cut nothing where its span ends inside the body.
Split Body by a face of a surface body now takes the faces joined to it tangentially (the exact
check Extend uses, within the one angle for smooth) and slices with them as they are, through
SMLib's slice by a sheet (smlib_split_body_by_sheet, tangency-labs/smlib 7a01f1b), its sides those
of the picked face. A sheet that only nicks the body cuts nothing, as before; a lone face, or a
face of a solid, still cuts with its surface extended.
3830 comes off the booleans list. Its answer counted the two halves of the cup and not the surface
that cut it, which stays as a body of its own (4879 removes its surface for that reason): three
bodies, the volume unchanged.
Needs SMLib 7a01f1b pinned (SMLIB_REV, prebuilt; its SMLIB_ABI_VERSION 6, which crates/smlib now expects) to link.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A surface body of more than one face (a fit-point spline's spans extruded, #3830) was refused.
Each face with a picked edge is now extended alone by SMLib's extension of its surface, and the
faces are sewn back together, each the face it was. A side that lengthens onto a face meeting it
tangent takes that face along, past its edge continuing the picked one; across a crease the
neighbour grows only when its edge is picked too, otherwise the extension is refused. Faces whose
lengthened sides no longer meet are refused. Up to a target keeps the pieces every grown face
lies in.
3830's extensions now build; its split still fails (the tool point picks one span, and a face
tool cuts with that face's surface alone), so it stays on the list with that reason.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Develop 38fd4a4f6's Reference tests fail 34, 35, 77, 78 and 81 (STEP export finds fillet edges
4.6e-5 to 6.1e-5 off their surfaces against 2e-5), 37 (the apex blend 0.193 off), 80 (the
taper-to-fit area) and 83 (thicken status 1001). Each expected.json names its cause in
known_failure, which the oracle already reads: a known failure that passes fails the job.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Develop 38fd4a4f6 (CI run 41157648345, after the SMLib eaa998a pin) fails 10 cargo tests; each
is listed with the cause its failure message gives. Seven are SMLib refusals or results off
their derived volumes (fillet, chamfer and shell), the cli action matrix and naming corpus
among them; the two corner_g2 tests are the fitted G2 corner patch bulging past the box, which
the explicit G2 corner fixes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
`cargo xtask known-failing --junit PATH` reads nextest's junit (a file, or every .xml under a
directory, so all of a run's junit artifacts at once) and fails on a test that failed and the
list does not name, and on a listed test that passed (FIXED: take its line off, as the kernel
rig's gate does). A listed test that did not run is neither, since a pull request tests only the
packages it touches. The list has the rig's KNOWN_FAILING format (`<test> <cause>`, sorted, the
rig's own parser), with `<test>` nextest's `<binary id>::<test name>`; `cargo xtask lists`
checks it is sorted. The list starts empty.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The round's centre (32 - r, 42 - r) leaves the hollow's corner (30, 40)
outside its circle, opening the wall, where sqrt2 (r - 2) = r: the case
expects the refusal naming 6.828. 2852's R30, refused naming 25.24, now
passes too: both come off the known-failing list.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The gate on aarch64 Linux reports 16 fillet cases FIXED with the pinned SMLib: the sloped and
equal-slope basin rim chamfers and rounds past their rims (1080-*, 5835-*), the pocket rim
chamfer past the floor, and the three pocket rim rounds now mitred at the pocket's corners
(every-pocket-*). No other area's gate reports a case fixed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
1080-fillet-sloped-basin-1-mm-rim-r0-5-4-edges asked G1 at every blend seam. Its front wall
leans 19 over 20 and the others 10 over 20, so at each rim corner the two mitred rounds meet the
sloped corner edge at different heights (0.155625 and 0.276393 below the top): the deeper round
runs on past the corner edge and is cut by the plane of the other's wall, a crease by
construction, the gap below the shallower round filled on that plane. The check now measures
the rounds' contact seams, on the top and on each wall, where the rounds are tangent. The
volume is unchanged.
With SMLib smlib-batch-4-mitre (1c15364): the case passes (V 144530.427946 against
144530.427909, 15 faces, sound); before it, only the four corner creases failed the check.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's trim took a fillet meeting its face at more than 78 degrees for one with no side
(smlib-batch-4-rulings 971e567); the chord of the knife edge's 0.5 chamfer meets the flat face at
81 degrees. The case comes off the known-failing list.
Needs SMLIB_REV at that SMLib once it is pushed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib (smlib-batch-4-rulings 0e83cca, SMLIB_ABI_VERSION 5) rounds the edges whose rounds overflow
their faces first and then what is left of the others; smlib_blend_dropping says which picks'
edges the overflow removed whole. The smlib crate binds it (Brep::blend_dropping), the kernel
returns those picks (fillet_removing), and a fillet notes them as its warning: "the edge at
(0, 0, 10) was removed by the larger round, so it is not rounded" (a 50 x 50 x 20 block, R21 on
its bottom front edge with the front left upright: the block is R21's alone, in closed form).
Ruling d8: [21, 5, 5] on a 20 cube builds as R21 alone (6107.529370); the test is no longer
ignored. R25 with R2 at a corner (blend_corner) builds the same way, R25's alone in closed form,
where it was refused. The rig's 1080 notched block outline at R8 builds now and comes off the
known-failing list.
Needs SMLIB_REV at that SMLib once it is pushed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With SMLib's smooth limit at half a degree (422e6f1) the 1 degree crease rounds R2 and R20
(the test is no longer ignored), and with a cusp's chamfer the ball of radius d (d231547) the
The 0.5 one stays, for its own cause (the chamfer face left apart from the body). Two corner
cases the same SMLib (replay/1.0.1 and those commits) builds come off too.
Needs SMLIB_REV at that SMLib once it is pushed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
smlib_chamfer turns the distance into a ball radius d sqrt((1 - c)/(1 + c)), c the faces'
binormals' dot (capi chamfer_radius); at #851's cusp the binormals agree, the radius is 0 and
the call is SM_ERR_INVALID_INPUT before the fillet executive runs (gdb: chamfer_edges sees
radius 0; the dump's why is empty). SolidCraft hands every chamfer to SMLib, so the
ball-contact chord (the ball of radius d: 3.822 wide at d = 2, 159.2365 removed) is SMLib's to
build.
Ruling d4 (2026-10-30).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Design preference surface_extrude_symmetric_per_side, which gave new
symmetric surface extrudes their distance on each side, is removed with
its Surfaces section, its session field and its labels. A symmetric
surface.extrude given no convention splits the total around the start
plane, as solid.extrude does; timeline.edit and timeline.redefine give a
one-sided extrude made symmetric the same. default_extrude_convention,
which only existed to read the preference, goes too.
An explicit `convention: legacy_per_side` and the marker saved designs
carry are unchanged. A saved preferences file that carries the key loads
as before (the prefs test now covers both removed keys).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's bar running tangent into a cylinder rounds its concave arc and
its top edge both together and one after the other in either order, at
r 1 to 7. Two more peg cases come off the fillets known-failing list.
The ladder's shelled dome ring now has 9 edges, not 7: each of its two
cylinder walls is one full-turn face with its seam edge (one wall face per
extruded circle), where it was two halves. Faces, vertices, area and volume
are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NvoxKQ2rEZvcXNQnhE3Sgs
Tests that asserted an older design rebuilds as the build that saved it made it
now assert what still holds: it opens, is upgraded, evaluates, round trips and
names alike every time, and a feature that lost a reference asks for it again.
- naming corpus: two builds still name every face and edge alike and find the
same faces with their stored names; a stored name that finds nothing must
leave its feature failed (it asks to reselect), never a feature that builds.
A sketch's face is found by its name as the sketch finds it.
- design corpus: the volumes, areas and bounds the saving builds recorded are
no longer compared; a corpus design may fail only by a request to reselect,
and undo leaves the features that failed on opening failed.
- fixed robustness seeds: no panic, valid bodies and volumes moving the right
way; a step the kernel refuses is not a bug.
- a format 28 design's pieces and a format 13 design's extra bodies: marked as
they open and named alike, without promising the numbers or names saved.
- action matrix baseline: the two corpus designs whose fillets, chamfer and
offset face held names saved before format 14 re-recorded.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>