Commit Graph
3176 Commits
Author SHA1 Message Date
Brennen HerbruckandClaude Sonnet 5.5 22fdb52498 kernel-cases: tessellation case from #466, skipped sources for sheet-metal, sweeps and tessellation
A revolved cone tip with an exact volume and area; auto-reports without
a design are listed in the skipped.json files.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 9c9ec27c3b kernel-cases: fillets cases from #1008, #1191, #3276 and #3753
A tray with seven rounded edges, both rim rounds of a tube, a chamfer on
a joined L-shaped body, and a circular pattern of a chamfered hole, each
with an analytic volume.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 8764a76ff8 kernel-cases: threads cases from #1995 and #3368 (finely faceted booleans), skipped #987 #3130 #3824
An M8x1 thread in a 7 mm hole, and three booleans of finely faceted
prisms (1000 and 1200 flat faces) with planar and curved partners, each
with a closed-form volume. Three auto-reports without geometry are
listed in skipped.json.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 c24b066d25 kernel-cases: an outcome for geometry with no single manifold answer
`"outcome": "solid_or_refused"` takes a clean refusal, or else grades the result as usual. Two
bodies that touch along a circle only (#168, #3841) have no one-solid union: a refusal or the two
bodies left apart are both right; fusing them is wrong. The two cases said opposite things
(two bodies, a refusal) and now agree.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 678a70da2c kernel-cases: shells as a graded count, no SMLib verdict where it can't take the record, $OUT
- `"shells": N` in expected.json grades the total number of shells: a body with a sealed void
  holds two, and some joins keep several lumps in one body. Those cases (#3175, #3455, #3526,
  #3730) are graded on validity again instead of being marked not valid.
- When SMLib's record conversion says "not supported yet" (revolved surfaces, traced intersection
  curves), its check gives no verdict. That's shown but not graded, since it isn't a fault of the
  body. solidcraft_kernel::SmlibCheck carries the three outcomes.
- `$OUT` in a recipe is a scratch directory outside the repository, for files a case writes. The
  two STEP-export crash cases write there instead of /tmp.
- cargo xtask kernel-cases --results FILE keeps every result as JSON.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 75aa8acb6c kernel-cases: sweeps skipped sources (72)
Every other sweep, loft, revolve, pipe, coil and rib issue and PR, one line each: auto-filed reports that carry only command parameters, reports cut off in the source, UI and dialog items, feature requests, and failures that belong to import, shell, fillets, booleans or tessellation.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 434a68bbc2 kernel-cases: sweeps coil and surface cases from #793-#4056
Coils split and trimmed by a plane, cut with a negative pitch, joined flush round a cylinder, intersected with a cylinder, cut as a thread groove into a bore, and placed with a square wire outside the diameter (screw-motion Pappus); surface revolve, sweep and loft sheets with areas worked out by integration, and a rail-guided surface loft in either section order.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 5f131cb888 kernel-cases: sweeps closed, twisted and joined sweeps from #561-#3897, ribs, tripod pipes
End faces of a loft, a sweep and a coil extruded, closed twisted sweeps round a torus, a twisted square cut through a tube, a ring swept along a short arc and joined to a collar, two overlapping swept arc walls, a rib grown along the sketch normal, and three pipes meeting at a point.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 a9002968f0 kernel-cases: sweeps sweep and pipe cases from #96-#3505 (end scale, rails, corners, closed paths)
End scale, parallel orientation and guide rails on straight paths (frustums and a sheared cylinder), a rectangle swept round a mitred corner, a profile mid-line on a closed rounded rectangle, second sweeps from a plane along a closed circle, hollow and cutting pipes, and a flat wall of a swept corner extruded.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 5e71db6628 kernel-cases: sweeps revolve cases from #2183-#4008 (refusals, flush ends, dome seam, primitives)
Refusals for a profile across the axis and an axis outside the sketch plane, a construction axis picked by name, a cone left by a revolve cut, revolve joins and cuts whose end faces lie in a face of the target, a dome cut by a ball on its seam, a horn-torus turn, and half-disc revolves with a refused hostile sweep scale.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 b60debec11 kernel-cases: sweeps revolve cases from #450-#2947 (faces, axis, cuts, seams)
Spherical shell sketched off the origin, adjacent profiles on the axis, whole planar faces of full and partial turns and a face pick on a fresh revolve, a half slot turned about its centreline (alone and as a cut), a torus cut by an overlapping ring, and a 300 degree revolve crossed by a plate.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 ec154f5421 kernel-cases: booleans cases from items another area had skipped (#451, #1107, #1140, #2928, #3850/#3741, #1984, #3573)
Added: 451 (block inside / crossing a hollow spherical-shell tool), 1107 (hollow hub joined
with nine blades), 1140 (spiral hollow lofted tube cut in half and joined), 2928 (cap-touching
lips with 0.0001 mm offset walls), 3850 with 3741 (cross cut touching a round side, and the
hole after it), 1984 (near-coaxial pin and rivet overlaps). #3573 is now a source of
shell/3576. Their lines are gone from the skipped files; #2259, #3518 and #3602 stay skipped
with corrected reasons.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 85f7200bbf kernel-cases: sweeps lofted tubes, blades and windows from #968-#2992
Hollow elbows lofted along a bend (Pappus), hollow bands halved and joined, a flange touching the end of a bent tapered loft, tapered and twisted lofted blades patterned round a disk, and a loft joined into a window that it overhangs, alone and mirrored on a hollow case.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 bec9db59e6 kernel-cases: sweeps loft cases from #96-#3936 (shallow cuts, cones, comb, rails)
A shallow loft cut from a slab top face, a loft cut whose sections touch the block sides given in either order, circles lofted into a cone on a turned-over plane, a loft guided by a rail, a circle lofted to a comb outline, a square lofted to a circle, and a circle-to-rectangle loft joined to a cylinder.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 739524a173 kernel-cases: sweeps lofts from #271-#3412 (zig-zag pairing, ring sections, flush joins and cuts)
Ruled lofts of zig-zag outlines worked out with the prismatoid formula, rotated rectangle sections turning through half a turn (Pappus), ring sections with round and rectangular holes, a cone loft meeting a cylinder wall near its top, a loft standing on a box face, a loft cut limited by targets, and a refusal for sections in one plane.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 ead88e582b kernel-cases: threads cases from modelled-thread reports (2 of 2), skipped sources
The rest of the thread cases (holes at the nominal size, shafts and holes
off the thread's size, the crash and sketch-attachment repros) and the
triage of the sources that are not kernel geometry.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 04135da965 kernel-cases: threads cases from modelled-thread reports (1 of 2)
External and internal modelled threads, tapped holes and threads beside
other features, each graded against the ISO 68-1 groove volume (Pappus)
and the part's own closed-form volume.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
jyvikoandClaude Opus 5.5 62124a7117 kernel: spline edges on part of their curve load as that piece
SMLib bounds an intersection edge on a piece of its spline (seed 32 intersect:
a block and a cylinder, the top disc's edges), and the truck decode refused
such an edge ("not supported yet: a spline or intersection edge on part of its
curve"), since truck bounds an edge by its curve's whole range.

bspline::segment cuts a B-spline to a sub-interval of its domain exactly:
Boehm insertion of both ends until each has multiplicity p, then the knots and
control points between them, clamped on the interval. The same points at the
same parameters, so the edge keeps its interval and the record its numbers.
load_edge_curve loads a spline or rational spline edge on part of its curve as
that piece; an intersection edge on part of its curve is still refused. Our
own records (interval = the curve's range) load as before.

Tests: segments of a rational cubic with a double knot, inside a span, across
knots, from or to a domain end, match the whole curve within 1e-12; both
spline kinds load on a piece with that range and the same points, and beyond
the domain are refused; SMLib's block ∩ cylinder decodes (it was refused) with
π r² h within 1e-3.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
2026-10-27 02:28:45 -04:00
jyvikoandClaude Opus 5.5 62142ef38e brep: a revolution of a closed profile is periodic along it
The adapter loads an analytic torus as truck's revolution of the whole profile
circle, a rational quadratic closed on itself, so an SMLib torus is one face
bounded by its two seam circles, each used both ways. The display evaluator's
domain gave a revolution a period around its axis only: projected along the
profile the loop jumped from one end of the knot interval to the other at its
start vertex, the plan failed ("boundary crosses itself") and the body fell
back to truck's mesher, which meshes a sphere bounded by its seam alone as
nothing (seed 60 union, a torus beside a sphere: 925.0 of 990.7 mm³).

tess::uv::closed_curve detects a closed profile the way closed does a closed
spline surface (clamped knots, first and last control point and weight the
same within 1e-9 of the polygon's extent; the shared checks are factored out),
the domain then has period = the profile's knot interval along it, and
EvalSurface::wrap/derivs wrap that parameter back into the interval, so the
plan's projection, unwrapping and both evaluators treat it as periodic. A
cylinder's or cone's line profile is unchanged.

Tests: a revolved whole circle, either parameter order, has both periods and
evaluates a period away as inside; SMLib's torus, alone and beside a sphere,
decodes without meshing to orient it, plans every face and measures within
1e-3 of 2π²Rr² (+ 4/3 πr³). With the closed profile undone the torus plan
fails as above.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
2026-10-27 02:28:45 -04:00
jyvikoandClaude Opus 5.5 ce201eea1b kernel: SMLib spheres cut by a boolean decode oriented and meshed
Results of SMLib booleans on its own spheres came back wrong through
body_from_smlib (side-by-side runner: seed 13 cut −1611.9, seed 61 cut −252.4
against SMLib's 4056.9, seeds 46/61 union 80 % short). The schema 4 records were
right (check_geometry passes, outer loops counter-clockwise, shells out of the
material); three things on the truck side were not:

- Body::new orients a solid by the volume of truck's coarse mesh, and truck's
  mesher meshes a sphere bounded by its seam alone as nothing: the rest of the
  body set the sign and turned it inside out. A foreign record is oriented by
  its shells, so body_from_smlib now builds the body with Body::oriented
  (revolved faces turned as before, orientation kept, nothing meshed).
- rephase_revolved turns each revolved face so it sits around angle π. A face
  that uses its seam both ways goes all the way round; turning its surface ran
  the wrap through the face's hole, the display plan failed and the sphere
  meshed as nothing. Such faces now keep their wrap on their seam (truck's own
  primitives have none: their round faces are split).
- The display plan opened only a loop of one seam used both ways. A sphere face
  whose meridian a trim splits uses each piece both ways, turning back at each
  pole, and projected onto one parameter line ("boundary crosses itself"), so
  the whole body fell back to truck's mesher and lost its sphere faces. A loop
  through both poles that turns straight back at one now has its run between
  the poles moved one period along, whichever way keeps it within one period
  with a positive area (poles split as the planner splits them); the routing
  check finds such loops too.

Test: SMLib's sphere less a box cap beside its seam, across it (seam split) and
a bar bored into its side away from the seam decode without meshing to orient,
oriented as recorded, every face meshed, within 1e-3 of the exact volume.
Before, the decode meshed the body to orient it; with only the plan's pole
handling undone the −x cap measures 50.3 of 469.1 mm³, with only the
rephase undone the bored ball 252.4 of 4059.5.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 5a6a91ebbd kernel-cases: fillets skipped sources (287)
Every other fillet, chamfer and blend issue and PR, one line each: auto-filed reports from private designs (picks and error only), sketch fillets and chamfers, UI, previews and navigation, feature and fit-option requests, reference cases that already exist in tests/oracle, surface modelling, and failures that belong to booleans, shell, import, tessellation, sheet-metal or threads.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 3dc7f90e63 kernel-cases: fillets correct the union volume quoted in 1262
The graded volume was right; the derivation text quoted the union as 46476.5 instead of 45571.7.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 d235bd7a0e kernel-cases: fillets pattern and G2 cases from #193, #219, #862, #1488, #2341, #2708, #2811
Copies of filleted and chamfered features (a pasted block, a pattern of pockets with corner rounds, a pattern of chamfered bosses), a grille of rib roots, a join that needs a boolean retry followed by a fillet, and curvature-continuous fillets worked out from the documented quintic section.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 cc3f8b1788 kernel-cases: fillets outline and corner cases from #237, #334, #485, #556, #851, #1207, #1213, #1262, #1557, #1667, #2498
Rounds along curved outlines, with the removed volume worked out by Pappus or by integration: merged cylinders, a D prism, a rounded rectangle with 0.02 mm end edges, a long box beside quarter turns, vertical corners after bottom rounds, a bent tube end, a boss's bottom arc, bars running into a boss, an edge ending on a curved wall, and the knife-edge arc corner.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 18af04b919 kernel-cases: fillets refusal, fit and straight-edge cases from #190, #199, #324, #896, #1668, #2752, #2852, #3369, #3435, #4141, #4143
Rounds with their own right answers: a radius larger than the ring it runs along (refused), a pick on a smooth seam (refused), a far edge pick (refused), a round that uses up an end face or a wall, a round over a hole, rounds on both sides of a thin wall and concentric with an inner one, a round on a sphere's flat cut, an edge ending on a tangent seam, and rims on B-spline ramps.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 aefca34522 kernel-cases: fillets chamfer cases from #814, #1080, #1390, #1986, #2672, #2719, #2797, #2907, #3655, #3779, #3868, #4055, #4101
Chamfers on boxes, plates, discs and sectors with closed-form volumes: all twelve edges in the order that was refused, a concave chamfer that adds material, a chamfer next to square openings and one that runs into them, a hole rim tangent to the bottom face, a hex hole's corner bevels, a one-pick chain on a large part, a bottom loop as wide as the corner round, two distances on a circular rim, the end outlines of a rounded prism, a chamfer over a joined pin, and the equal chamfer of a slanted plug. Spline-sided pillar (invariants only) for chamfer and fillet.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 6a9b8fd740 kernel-cases: booleans from #3404-#4124 (28 cases, 76 skipped)
Cases: mirror of a cut under a wall (#4011), coplanar intersect (#3671), multi-lump
intersect (#3526), split along a face plane (#3447), 64-peg join (#3455), boss on a rod
(#3485), collinear cylinders and pin in a bore (#3497), swept G2 cut (#3604), spokes
tangent to a hub (#3612), sphere and pyramid (#3633), column in a channel (#3665),
extrude to a point on an edge (#3729), emboss on a cylinder (#3782), circle-only join
(#3841), ring on a perforated plate (#3887), symmetric revolve cut (#4008), walls round a
floor (#4058), slab beside a bore (#4095), and others. The rest are skipped with a reason
in skipped-c.json.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 0ae42f4111 kernel-cases: sheet-metal skipped sources (87)
Every other sheet-metal-keyword issue and PR, one line each: UI, docs, file
format, naming and attachments, DXF output, feature requests, user designs
with no repro, and failures that belong to booleans, fillets, shell, sweeps
or threads.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 676670ba80 kernel-cases: sheet-metal tray and unfold cases from #349, #405, #436, #514, #723, #1797, #3417
Trays at 72 degrees and with four angles and heights, a tray shrunk by a
parameter and unfolded, an L bracket unfolded and refolded, opposite flanges
at 105 and 120 degrees, torn corners folded, and a rhombus whose square
reliefs would overlap.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 474f608536 kernel-cases: sheet-metal convert and unfolded tray cases from #479, #488, #723, #725, #839, #1092, #1285, #1481
Unfolded trays graded by the flat size W + 2(H - BD): torn, round and square
relieved corners, per-feature reliefs, rounded plate corners; a shelled tray
and a bracket converted at their bends; an L converted to the rule's radius.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 943a7d66b4 kernel-cases: sheet-metal flange and cut-out cases from #416, #529, #570, #601, #634, #659, #702, #978
A flange beside the leg of an L, along what a cut-out leaves of an edge,
beside a ledge as tall as its setback, a return on a flange's far edge, a
round hole, a slanted slot and an ellipse across a bend, a hundred slots with
four folds, and the refusal of rule values sheet.flange would ignore.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 b13155cbbf kernel-cases: sheet-metal cut-out, flange and refusal cases from #296, #1095, #1280, #1295, #1311, #1979, #3078, #3234, #3324, #3353
Cut-outs folded and refolded, a hole square to a 45 degree flange, a slot
that parts a flange from its base, an inside flange on a plate turned
62 degrees, cuts after cuts, a hole beside two adjacent flanges and a flange
on a flange's side edge; refusals for a flange on a bend line and a flat
pattern after a fillet; a mirrored sheet body that must stay sheet metal.
Volumes by hand (K = 0.5 folds: flat area * t; otherwise bend volumes).

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 a11a736ce8 kernel-cases: sheet-metal convert and hole cases from #774, #1040, #1092, #3316, #541, #542, #560, #955
Plates converted to sheet metal (holes, long thin strips, engraving, a
channel with modelled bends, position kept) and holes and cut-outs
through or into a sheet; volumes by hand from the plate and the holes.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 3c465e6801 kernel-cases: sheet-metal fold cases from #262, #264, #638, #639, #685
Folds of tabs and plates, graded by closed form: a fold keeps the blank's
flat length, so V = flat area * t + theta * w * t^2 * (1/2 - K). Tabs
on one line (#264, #638), a tab on an L's inside edge (#639), a fold just
inside a tab root and a refusal at the root (#262), a fixed point on the
top face of a large plate (#685).

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 611567c63c kernel-cases: booleans from #2896-#3383 (11 cases) and the skipped list
Cases for the near-contact gap join, a countersunk hole beside a distant
body, a perforated plate under a ring, a sealed void, a rim and tooth join,
a frustum cut, a line-to-line pin, a flush notch, spoke patterns and a join
into a rotated occurrence. The rest of the bundle is in skipped-b.json with
one line each.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 6cf966bd50 kernel-cases: booleans from #2564-#2896 (11 cases)
Hand-derived cases for tapered and collinear extrudes, pattern and mirror
copies keeping their targets, a cut up to a face, a prism joined to a
round-cornered slab, a clip round a small hole, and near-contact joins.

2564, 2583, 2601, 2754, 2755 (pattern, mirror), 2801, 2810, 2826, 2580,
2896 (overlap)

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 48db4fa2cf kernel-cases: booleans from #13-#2534, first half (30 cases, 73 skipped)
Spheres cut twice (#1717), box/cylinder intersect (#1647), crossing cylinders
moved far (#1649), coaxial cut from a thin disc (#500), coincident cylinder
walls (#114, #2008, #1910, #1865), rim touching a coin (#168), holes along
walls and beside rounds (#559, #562, #1279, #1355, #2055), tangent holes
(#307), blind cut in a cylinder (#308), through-all cut (#423), shallow cuts
(#1858), skin left by a short cut (#1730), delete face (#1927), collinear
extrude sides (#1949), hidden bodies (#2464), mirror and patterns (#2003,
#2524, #2076), tapered extrudes (#831), text cut (#1195), split (#13).
Every other item in the bundle is in skipped-a.json with its reason.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 035aa6512e kernel-cases: tessellation skipped sources (253)
Every other tessellation-keyword issue and PR, with one line each:
rendering and GPU drawing, UI, performance, display-plan plumbing, and
failures that belong to booleans, fillets, threads, import, shell,
sheet metal or crashes.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Sonnet 5.5 8ff1b2a650 kernel-cases: tessellation cases from #311-#2712 (14 cases)
311 ramp cut across a round blank, 784/811 filleted and drilled bodies
for STL export, 818 blind hole in a filleted ring, 819/921 pocket that
splits a wall seam, 1263 concave arc with a knife-edge tip, 1615/1653
crossed lofted tubes, 1648/1850 sphere touching a box edge, 1666/1670
two twisted lofts, 1753 bowl rim cut by a cylinder, 1813/2712 lens face
thinner than the tolerance, 2069 notched ring moved far away, 2528
slot joined with an overlapping cylinder.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 02712a003a kernel-cases: crashes and hangs from the #140-#4149 reports (9 cases, 45 skipped)
140 join with a pad hanging past the edge, 1219 bore fillet then grooves,
1985/2243 STEP export of two enclosures, 3540 cut with a coincident cylinder
face, 3685/1559 delete a fillet face, 4092 loft + ribs + pad union (two
recipes), 2992 disk and 36 twisted loft blades. Everything else is skipped
with a reason (private designs, other areas, UI, perf only).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 0eae22a5e6 kernel-cases: import from #1721-#4006 (19 cases, 59 skipped)
STEP: 3730 void shell flag, 3098 tiny-knot B-spline edges, 2043 opposing
surface sense, 3208 extruded ellipse over its seam, 3352 vertex off its
curve, 3963 closed spline edge, 4005/4006 near-degenerate cones, 3871
cone point, 3880 seam cylinder and dome, 1721 closed B-spline tube.
IGES: 3806 revolved arc cap, 3845 trim gaps, 3359/3913 reversed trim
pieces, 3886 tiny knot span, 3912 reversed hole trim, 3972 two boxes.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 771a48e4ff kernel-cases: shell and offset from #12-#4144 (21 cases, 59 skipped)
4009 closed shell, 4010 shell open at a hole wall, 2531 point pick after an edit,
3468/3898 offset next to a fillet, 12 split face piece, 566 swept bar, 745/3893
freeform boss (two variants), 3103 tapered cylinder, 3669/2990 loft, 3283/3650
and 2939 curved offsets, 3506 and 1972 split then shell, 3576, 391, 1494, 1525.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 c3a0b09519 kernel-cases: the no-keyword kernel items, #25-#4148 (4 cases, 98 skipped)
Cases: #3702 (a board in the cavity of a case with a filleted rim, cut leaves the case
unchanged) and #258 (STEP cone to a point, with and without an apex vertex, and the 0.5 mm
pin). Everything else in the bundle is skipped with a reason in skipped-other.json.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
bherbruckandClaude Opus 5.5 7bb74d1c6b kernel-cases: an smlib feature for the CLI, and no grading of a kernel the build isn't running
- solidcraft-cli and solidcraft-engine forward an `smlib` feature to solidcraft-kernel/smlib, so
  `cargo build -p solidcraft-cli --features smlib` gives the rig SMLib's check.
- solidcraft_kernel::boolean_kernel() says which kernel this process runs booleans on.
  `default` until the SMLib switch (SOLIDCRAFT_BOOLEANS=smlib) lands and answers there. An smlib
  run on a build without the switch reports "not supported yet" instead of grading the default
  kernel under SMLib's name.
- An area may keep its skipped list in parts (skipped-<part>.json).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:45 -04:00
Brennen HerbruckandClaude Opus 5.5 a7c0109eab kernel: boolean runner grades the seeds against a reference volume
Rows without an analytic volume (the fuzz seeds) get one from the
primitives' definitions, by no kernel: along each vertical line both
operands are exact z intervals, combined exactly, integrated over a grid
whose cell edges include every straight face, with the half-resolution
grid bounding what error is left. Each kernel's volume is graded against
it (within 1e-3 relative or 3x that bound), in the JSON per row and in the
report's summary.

On 64 seeds truck is right on all 192 rows. SMLib's own measure is wrong on
13, all with cylinders or spheres, although truck's measure of the same
exported bodies is right on every one of them; 5 give no closed solid.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:44 -04:00
bherbruckandClaude Opus 5.5 732fd2ace2 kernel-cases: a regression rig that grades each kernel against the case's own answer
Every geometry case the old kernel got wrong becomes tests/kernel-cases/<area>/<id>/: an
engine script or oracle recipe, and expected.json with the right answer, from analysis or a
hand calculation, or else the invariants. Never a kernel's output.

- solidcraft-cli kernel-cases <dir>...: runs a case and grades it. The checks are the outcome
  (succeeds, or refuses cleanly), the body count, and one closed shell per body that passes the
  record's structure and geometry checks and, with SMLib built, SMLib's check(All). Counts,
  volume, area, centroid and box are graded where the case gives them. Each run is pass, fail,
  not supported yet or crash.
- cargo xtask kernel-cases [--kernel default|smlib|both]: one process per case, so a native crash
  or a hang (--timeout) is that case's result. It writes docs/kernel-cases.md: coverage per area
  and source, results per kernel, and the sources looked at and skipped (<area>/skipped.json).
- solidcraft_kernel::validity and smlib_built, which the rig's checks use.

tests/kernel-cases/README.md gives the format.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:44 -04:00
jyvikoandClaude Opus 5.5 79ae117dd9 kernel: boolean runner measures SMLib's results again on truck
When SMLib's volume of a boolean result differs from truck's, the report could
not tell a wrong body from a wrong SMLib measure. The runner now measures the
result it exports back to truck as well, keeps that volume in the JSON, and
shows it in the export column wherever it leaves SMLib's own measure or SMLib
could not measure the body at all.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
2026-10-27 02:28:44 -04:00
jyvikoandClaude Opus 5.5 ac6ddbdbec kernel: boolean runner times both kernels and runs the cut sequence
The side-by-side runner now reports how long each boolean takes on truck and
on SMLib (the call alone), and apart from that the SMLib side's conversions:
the operands' truck→SMLib import and the result's SMLib→truck export, which
the app pays while truck still holds the bodies. The report gains a times
summary (median, worst, total), solid counts, the analytic volume of each named
case's union, intersection and cut, and how many results land on it.

It also runs the "each cut gets slower" case from TASK_kernel-smlib-booleans as
a named sequence: a 63.6 × 31.7 × 9.5 block, a Ø20 × 10 boss joined on top, a
slot front to back, a Ø6 cross hole through the boss and a slot that splits
the block, each step on the previous result. SMLib keeps its own results from
step to step (only the tools come from truck), in a child process like the
cases, and every step's volume is checked against its closed form.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
2026-10-27 02:28:44 -04:00
jyvikoandClaude Opus 5.5 2196129f16 kernel: side-by-side boolean runner calls SMLib's boolean
The smlib_booleans example answered "not supported yet" for every SMLib case.
Now it runs solidcraft_smlib::Brep::boolean on the tagged operands (cut maps
to Subtract, None is an empty result), reads the result's history from the
tags, and measures its volume with mass_properties at MEASURE_ACCURACY, so the
report compares truck and SMLib on real results.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
2026-10-27 02:28:44 -04:00
jyvikoandClaude Opus 5.5 19cf3d94ac brep: orientation, not position, tells a face's outer loop
truck lists some planar faces' hole loops before the outer loop, so the
rule that loops[0] is the outer loop never held for truck's records; moving
it in the adapter would renumber those faces' edges, which history and
names stand on. The outer loop is the one that runs counter-clockwise about
the natural normal (what check_geometry checks); the order is the
producer's, and SMLib's import puts the outer loop first, as SMLib needs.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
2026-10-27 02:28:44 -04:00