Every tapped hole now drills the tap maker's tabulated drill. ISO metric takes Yamawa YEU23's
drill size column for cutting taps (printed p.704, M coarse; pp.704 to 706, MF fine): M8 drills
6.8 mm and M12 10.3 mm, where the major less the pitch gave 6.75 and 10.25. A custom metric size
the table lacks keeps the major less the pitch. UNC/UNF (Guhring), G, Rp, Rc and NPT (Yamawa)
were tabulated already. The Thread command's suggested hole for a metric size follows.
The Hole dialog's Tap drill diameter is now a field, the tap maker's drill by default, and the
command's `diameter` with a thread is checked the same way: a drill is accepted from the
internal thread's standard minor diameter (or the tap maker's drill where that lies below it:
Rp, Rc, NPT) to 5% over the tap maker's drill. Outside that the command names the range and
why. The field's tooltip gives the drill, the minor diameter and the range. Presets keep a
chosen drill.
A saved design keeps the diameter it stored, so it builds as before, and editing such a hole
keeps its drill: no preference and no format change. Scripts that give a thread without a
diameter drill the new default; ladder 05/007, 11/003 and rig case threads/2115 follow
analytically, and their golden entries are re-measured from runs (tier 05 re-sorted by time).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
The Rc and NPT drills were rounded to a drill series from a third-party reproduction of DIN 345
and a fractional/letter inch series cited from memory. They now come from the same tap maker's
catalogue the G and Rp drills do: Yamawa YEU23, printed p.709 (Rc, the maximum straight bored
hole with non-full threads, Rc 1/16 to 4) and p.710 (NPT, the maximum straight bored hole, 1/16
to 3). A size its tables lack (Rc 5 and 6, NPT 3 1/2 to 12) is refused as a tapped hole, naming
the range. The dialog's tooltip keeps the standard's minor diameter where the thread ends.
Rc 1/2 drills 17.6 mm (minor 17.807), 1/2 NPT 17.60 mm (minor 17.473).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
An Rc or NPT hole was drilled to the exact minor diameter where the thread ends, a size no shop
stocks. It now takes the largest stocked drill not larger than that: metric drills of the DIN 345
series for Rc (to 100 mm), letter and fractional inch drills by 64ths (to 1 1/2 in, ASME B94.11M)
for NPT; past the series it is bored to the exact value. The Hole dialog's drill shows the inch
size for NPT, and its tooltip the exact standard value. Rc 1/2: 17.807 mm, drilled 17.75 mm;
1/2 NPT: 17.473 mm, drilled 11/16 in (17.4625 mm).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
The thread dialog offers the pipe threads: G (ISO 228-1), Rp (ISO 7-1), R and Rc (ISO 7-1) and
NPT (ASME B1.20.1). Their sizes are listed by designation without a pitch, one start and a hand
of right or left; a size picked for a hole the dialog sized Rc stays Rc.
Rp, ISO 7-1's parallel internal thread an R screws into, is a form of its own (`rp`): the
parallel profile (H = 0.960491 P) at ISO 7-1's gauge diameters, refused on a shaft. Its cut
meets the analytic material of its profile within 1e-5, as G does.
A taper thread takes a chamfered tip: each end's cone is measured from the major diameter the
taper has at that end. Pipe threads are not ISO metric, so they give chamfer_depth.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>