* Delete: the check in a rolled-back history builds the history once when nothing breaks (#9917)
With the history rolled back, the check before a delete (which features
the delete would break) built the whole history twice, before and after
the change, with the marker removed. On a large design each build ran
every boolean after the marker: deleting twelve splines took half a
minute on the window thread. Only a feature that fails after the change
can be newly broken, so the history after it is built first, and when
nothing fails there the history before it isn't built at all.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Delete: test that the check in a rolled-back history still reports what breaks (#9917)
Deleting a hole in the plate changes the plate and every cut after the
marker and breaks none of them: the check reports nothing. Deleting a
side of the outline breaks the plate, and the check still says so, with
a cache too small to keep a state.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
joint.create's flip text and the assemblies guide said two origins at one
point with the same z stay as they are; a point origin without x takes its
x from z, so a part turned about z turns back. Say so, and point to giving
x on both origins or joint.as_built.
edit.checkpoint and edit.restore_checkpoint now say that restoring or
forgetting uses the checkpoint (and later ones) up and that only the last
16 are kept, and the "no checkpoint N" error says why. The editing and
mechanisms skills no longer read as if a checkpoint can be restored twice.
Co-authored-by: thocsmith <193096300+thocsmith@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #8100
* History: say why an edited feature behind the marker changes nothing (#8100)
Editing a feature that sits after the history marker (double-clicking its
greyed-out item) rolls back to it, previews the change, and on OK puts the
marker back where it was: the feature stays rolled back, so nothing in the
view changes and nothing says why. That is the silent "pattern of a cut
does nothing" in #8100 (the reporter's design has its pattern behind the
marker; on main the pattern itself builds fine once rolled forward).
- timeline.redefine replies `rolled_back` and, when true, a `note`; it also
carries the feature's `warning` (for a rolled-back feature, the one its
constructor met building it at its place).
- The window shows that note in the status line after such an edit.
- A rolled-back item's tooltip in both History layouts says it is after
the history marker and not built.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Pending locale: Arabic, Hebrew, Japanese, Vietnamese and Chinese for the rolled-back notes
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #8306
* Timeline: joints in feature folders (#8306)
timeline.group and timeline.move_to_group take joints as well as features, so
hundreds of joints fold into one folder tile. A closed folder shows one tile
whatever it holds; opening it shows its features and joints in both the bottom
and left History. Suppress, delete and ungroup on a folder reach its joints too
(one undo step), deleting a joint removes it from its folder, and an unknown
joint id or name is an error. Saved with the design; designs without joint
folders read and write as before.
* claim: #3693
* Fix timeline playback to show each rebuilt feature
* Move History playback into the Inspect ribbon
* Refuse Play History up front when playback couldn't run
Starting Play and the per-frame check that stops it were looking at
different app state, so Play could be accepted during an apply, a delete
check or queued history work and then stop silently on the next frame.
Both now use one playback_blocked check.
The UI also reads the engine's PlaybackAction as the typed enum instead of
matching strings, so a bad reply is an error rather than a quiet toggle.
* Put Play History in the History controls
History now shows five controls in transport order: start, previous,
play, next, end. Play runs timeline.play, so it turns into Stop while
playback runs, same as the ribbon button and the shortcut.
It's on by default (#3688, #3740, #4216). Anyone who wants the old four
controls back can right-click them and pick Hide Play Button, or clear
history_play_button under Preferences > Interface. In a named vertical
History too narrow for five buttons beside its grip, Play is left to the
ribbon rather than overlapping the grip.
* Draw the History Play button as a plain play/pause glyph
The Play button in the History controls now uses the same drawn glyphs as
its neighbours: a filled triangle, and two bars while History plays. The
triangle is bigger than the step arrows so it doesn't read as Forward.
The ribbon command keeps its timeline_play and timeline_stop icons.
* Keep the playback changes clear of PRs queued ahead
Several PRs in the merge queue touch the same lines, so this moves ours
aside without changing behaviour:
- history_play_button and its reset-test row sit with the other History
preferences, not beside view_confirm_corner (#7248 adds status_bar there).
- History keeps main's history_transport_width() for four controls (#6430
and #7459 call it); the Play button's count uses history_controls_width.
- A new or opened document stops playback after dim_view::cancel(), clear
of the line #7819 adds after reset_chat.
- The Play/Stop label swap moves from interactive_command_info, which #7906
rewrites, into the ribbon's command_info.
* Stop playback after the command completes, clear of #6433#6433 rewrites the session.execute line in execute_command, and our playback check sat right under it, so the queue couldn't merge the two. Checking the revision after command_completed does the same job a couple of lines later.
---------
Co-authored-by: cfaulkingham <colin.faulkingham@gmail.com>
* claim: #6651
* test(#6651): a list parameter of the wrong type is refused
A list parameter such as a cut's `targets` or an export's `bodies` loses entries without an error: a value of the wrong type reads as an empty list, which most commands take to mean "every body". The regression test drives the engine the way a user does: two bodies, a box cut that crosses both and is meant for one of them, and a `targets` of the wrong type. The command must refuse it and leave the design as it was.
* fix(#6651): a list parameter refuses a wrong type instead of losing entries
A list parameter of the wrong type was read as an empty list, and an empty
list means "every body" to most commands: a cut meant for one body cut every
body it touched and the command reported success.
A wrong type is now an error that names the parameter, the offending entry
index and the value it got. A list longer than 10000 entries is an error
instead of being cut short. `null` stays absent, as the schema contract says,
and a plain string is still a list of one. The 80 call sites now propagate the
error instead of losing entries; the commands that take feature keys, which
may be named or numbered, read them with their own reader.
* claim: #5694
* Redefine: the reply reports the features it rebuilt (#5694)
timeline.redefine builds the edited feature and the features after it in its trial session;
the session's own evaluation then only takes those results from what the trial kept, so the
reply reported that second evaluation and read as "nothing was rebuilt" although the geometry
changed. Report the trial's rebuild, plus anything the session still had to compute itself, as
timeline.edit reports the same change; `restored` keeps counting only genuine reuse of earlier
results.
Tests: redefining_reports_the_features_it_rebuilt fails before the change with
{"feature": 2, "recomputed": 0, "restored": 2} and passes after it;
redefining_computes_the_later_features_once still guards the single computation (the reply
doubles if the kept results are lost).
* claim: #7253
* Sketch: deleting a dimension in a rolled-back history no longer rebuilds the features after the marker (#7253)
The check before a delete evaluated the whole history twice when the
timeline was rolled back. Removing a sketch constraint changes the later
features' cache keys, so on a long history Delete on a dimension took
minutes. When the design differs only in sketch constraints (and model
parameters nothing uses any more) and each changed sketch solves to the
same geometry, profiles and ends, the features after the marker see the
same inputs: compare the live models only. Anything else still gets the
full check, so the report is unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6380
* Cylinder: place by distances from reference edges, like Hole (#6380)
A Cylinder standing on a flat face can take up to two straight edges of
that face as references, each with the distance of its base centre from
the edge's line, measured in the face's plane, as a Single hole does
(#37). `solid.cylinder` takes them as `references: [{edge, distance}]`
with a numeric `base`; the edges are found again by their persistent
names, else their points, so the cylinder follows them when the part
changes, and each distance is a parameter (an input of Inspect Feature).
A cylinder without references stays at its base, as before.
In the Cylinder window, started on a picked face, Reference 1 and 2 take
the edges, each with its Distance measured from the pick, so it works
with the mouse alone; the canvas shows each distance with a box to type
it in, and Edit Feature picks the edges again.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Cylinder: Edit Feature shows each reference edge input once (#6380)
A face selected when Edit Feature opened the window had already added
the reference inputs; the edit added them a second time.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Cylinder references: the measured-once cost test's cylinder has none (#6380)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Cylinder: pick the face it stands on in its window, then the edges (#6380)
The Cylinder window took its place only from a face selected before it
opened, so started first it stood at the origin and offered no reference
edges. It now has a Face input before Reference 1 and 2, as the Hole
window does: start Cylinder, click the face, click the edges, OK.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Glossary: reference edge, and "Reference" among the words with more than one meaning (#6380)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Cylinder edge references: the Cone dialog (#6250) gets the references field too
The Cone primitive landed on main after this branch began; its dialog initialisers lacked
the `refs` field the Primitive kind gained here. The dense form check for Cylinder fills only
its fields: its face and reference edges place it, which the reference tests cover.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Cylinder: declare references in its contract; reference-placed cylinders are not placement-independent
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #7077
* Repeat Last Command in command search, with a key you can change (#7077)
Shift+R already started the last tool or dialog again (#3045), but it was a
key the app kept for itself: command search could not find it and Keyboard
Shortcuts could not change it. It is now the command edit.repeat, with
Shift+R as its default key. A call through the engine is refused, because
only the app has a tool to start.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Locales: Arabic and Hebrew for the new strings
ar and he are complete catalogs on main now (#3458): every new message
needs them. The pending-messages test compares right-to-left messages in
display order once #7532 lands (#7527).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Locales: Vietnamese for the new strings
Vietnamese became a complete catalog on main (#5823), so every new English
message needs it too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #7219
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* History: delete a folder with its features, and suppress a whole folder (#7219)
`timeline.delete` and `timeline.suppress` take `groups: [timeline folder ids]`:
every feature in those folders and their nested folders, in one undo step.
A delete takes the folders themselves too; `timeline.ungroup` still keeps the
features. The History on the left offers Suppress/Unsuppress Selected Folders
and Delete Folders and Features… (asking first, like Delete Selected
Features…, when something outside needs them); a folder whose features are
all suppressed is drawn faint.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* History folder actions: Arabic, Hebrew and Vietnamese strings (complete catalogs)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
timeline.redefine evaluated every later feature in its trial session, then again in the session:
the evaluation cache keeps only the last few states of a design with large bodies, so the trial's
results were gone by then. The trial keeps them in the session's kept results (or its own), and
the session's evaluation takes them from there. EvalCache::with_budget gives tests a small cache.
* claim: #6724
* Extrude: the picked region is the one extruded again (#6724)
Since #5530 (#5302) every index or point pick grew to the whole drawn
profile that reference geometry cuts, so a lens or crescent clicked in
Extrude, where the face's projected outline cuts a circle, extruded the
whole circle while the dialog highlighted and counted one region.
Dialogs now send exact_regions: true with their profile picks, and the
command keeps each pick to the region it names. Picks without the flag
(scripts, agents, the CLI) still take the whole drawn profile (#5302).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #2175
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Body rename: an imported assembly's other bodies keep their names and components (#2175)
An Import keeps its body names by the file's body index, and builds no body for the
file's later instances of a repeated part (`skip`). Renaming a body stored the names by
the body's place in the model instead, so every name after the first skipped instance
landed one slot early (and the new name could land on a skipped slot). The rename looked
right until the design was rebuilt; then those bodies took other names, dropped out of
their components and showed up loose in the import's top component.
`Feature::body_name_slots` maps the bodies a feature builds to their stored slots, and
`Feature::pin_body_names` stores current names through it. The rename, the pinning of
later features' names (rename and suppress) and `Document::body_rename_from` use them.
Fixes#2175
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6186
* Timeline: a reorder evaluates the design once, from the cache it already has (#6186)
timeline.reorder checked the move on a copy of the model, then dropped it,
so setting the reordered design evaluated the moved part of the timeline
again; reorder_many (and moving features into a group) checked on an empty
model, recomputing the whole design even for a move near the end. The
check now starts from the session's own model, and the session keeps the
model it was checked on.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Marker is Copy: drop the clone
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #4094
* Sheet metal: Path Flange, a chain of bends on an existing sheet edge (#4094)
Path Flange (`sheet.path_flange`): sketch an open chain of lines across a sheet edge, pick the
edge and one line; each line becomes a flange as long as the line and each corner a bend, one
feature and one body. The edge flange takes further bends (`then`), each on the far edge of the
one before, and the Flange dialog shows them as rows with a bin each.
* claim: #5962
* Timeline: reorder anyway (allow_errors) and report the features the move breaks (#5962)
timeline.reorder and timeline.reorder_many refuse a move after which a
feature that worked would fail. Sometimes breaking a later feature is the
point: an agent restructuring a design wants the move made, then the list
of what broke so it can repair those features next.
Both take allow_errors (default false: refused as before). With it the
move is made and the reply lists broken: [{feature, error}] (empty when
nothing broke); one undo puts the order back. timeline.reorder_many also
takes active, as timeline.reorder does.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Undo: what is hidden lives in the snapshot, so hiding is a step (#2219)
`Session::execute` records a step only when the document `Arc` changes, and what is
hidden lives in `Session::visibility` — saved with the design, but outside the
document. `browser.visibility` was also declared `.noundo()`, and `Snapshot` had no
field for it, so even a recorded step could not put a hidden body back: undo went to
the command before the hide and left it hidden (#2219).
`Snapshot` and `Checkpoint` now carry the `Visibility`, `go_to` restores it, and
`Session::execute` treats a visibility change as a change of its own. That change is
display-only, so it refreshes the view with a revision bump (`refresh_display`)
instead of evaluating a model a hide does not touch.
The command also takes `folder: "all"` (every body, sketch, construction item, origin
item and joint, plus the browser folders and occurrence hides) so Show All can be one
step, and asking for the state an item already has no longer reorders the hidden
lists: a redundant hide is not a step and leaves no unsaved changes.
* Show/Hide: the menus run browser.visibility, so the history has it (#2219)
The hide and show actions wrote `session.visibility` directly instead of running the
command: the body and face menus (`ui.hide` / `ui.show`), the `V` key
(`context_menu::toggle_visibility`), the browser rows' eyes, the Origin rows and
`ui.originAll` / `ui.originPart`. The engine could record a step and there was
nothing to record — which is why the release still answered "nothing to undo" after
hiding from the Browser.
They all run `browser.visibility` now (the repo rule that the UI acts through
commands), and `ui.showAll` is that one `folder: "all"` call, so Show All is one undo
step rather than three. `docs/occurrence-workflows.md` says what visibility does in
the history.
A Single hole can take up to two straight edges of its face as references,
each with the distance of the hole's centre from that edge's line, measured
in the face's plane. `solid.hole` takes them as `references: [{edge, distance}]`;
the edges are found again by their persistent names, else their points, so
the hole follows them when the part changes, and each distance is a
parameter. A bad reference (no edge there, a curved edge, one square to the
face, parallel edges, a negative distance, a centre off the face) is refused.
In the Hole dialog, Reference 1 and 2 follow the face, each with its Distance
row; the canvas shows each distance as a dimension from its edge to the hole,
with a box just past the edge to type it in. Picking an edge measures its
distance (and its box takes the keyboard), typing one moves the hole, and
moving the hole measures them again. Edit Feature picks the edges again with
their distances.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #4302
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Timeline: suppressing a feature keeps later features' body names (#4302)
Bodies numbered by the counter (`BodyN`) take the next free number on every
recompute, so suppressing a feature that made one moved every later counted
body down one (`Body2` became `Body1`) and broke what named it, such as a
Move of `Body2`. timeline.suppress now stores the current names of later
features' counted bodies in their `body_names` first, as body.rename already
does for a renamed counted body (#1109). Engine only: no evaluation or
design-format change.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Timeline: a body made while a feature is suppressed keeps its name (#4302)
Suppressing a feature freed its counted name (`Body1`), so a body made
meanwhile took it and became `Body3` once the feature was back. Suppress
now also stores the suppressed feature's own counted names, and the
evaluator adds the names stored on earlier suppressed features to the
state's `reserved_body_names` (the names a rename freed, #4957), which the
`BodyN` counter passes by. They are taken from the design before each
feature is computed and are part of the state digest, so a cached result
is only reused when they match.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #4100
* Deleting an inserted file removes its components, placements and joints (#4100)
A STEP or mesh file inserted into a design makes a component tree. Deleting
its feature left that tree behind: the components, their occurrences, the
rigid joints that hold them and the bodies' component assignments. A later
body that took an imported body's name was then placed in the stale component.
Document::remove_component_tree removes a component subtree and everything
that refers to it: the features made inside it, its occurrences, the joints
on them with their motion links, joint origins, contact set members, motion
study keys and exploded moves, body component and offset entries, standard
part and link records, and configuration columns. Deleting an inserted
file's feature and component.delete both use it; component.delete now also
removes joints left pointing at a deleted occurrence. The body transfer
refusal moves with it, unchanged.
* Only an inserted file's feature takes its component tree when deleted
Mark the feature a STEP, IGES or mesh insert makes (`inserted`), and remove
the component tree on delete only for those and for a linked design's
feature. Deleting a copied component's independent base deletes just that
feature, as before. Older designs get the mark as they open (pending format
change), except copied components' independent bases.
* claim: #3471
* Delete in a rolled-back history warns about the features after the marker (#3471)
With the timeline rolled back, the checks a delete runs first (the
confirmation's "these features will fail", timeline.dependents and
selection.delete's would_fail) compared models evaluated only up to the
marker. Features after it, broken by the delete, were not listed, so their
error marks turned up only once the timeline moved to the end.
newly_broken_in_history evaluates both sides over the whole history when
either has a marker (on copies; the model and document are unchanged) and is
used by the delete's report and by timeline.dependents.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #4003
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Frames: the profile library (#4003)
The first slice of frames and weldments: the cross-sections structural members
will be made of, each SolidCraft's own parametric definition built in code
(no vendor or standard size tables are shipped).
- solidcraft_doc::frame: bar, round bar, rectangular and round tube, angle,
channel, I-beam and a generic T-slot extrusion as exact line/arc regions,
with defaults worked out from the profile's size, refusals that name the
dimension that does not fit, anchors and placement, and exact section
properties (area, centroid, Ixx/Iyy/Ixy by Green's theorem).
- frame.profile.list, frame.profile.properties (with mass per metre for a
density) and frame.profile.insert (draws a profile into a sketch, locked by
default, at a point, anchor and angle).
- Tests against hand-computed values (rectangles, circles, composite
rectangles by the parallel-axis theorem, fillet spandrels), hostile input,
extrusion volume, undo; catalog entries in every locale; docs/frames.md;
ROADMAP M15.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Frames: drop the built-in T-slot profile (#4003)
Aluminium extrusions and other vendor sections come from the user's own
sketch (drawn or inserted from the vendor's DXF), so the library keeps the
plain steel shapes only.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Frames: members along frame sketch lines (#4003)
frame.member lays one body per straight line of a frame sketch (2D lines or
3D sketch lines), its cross-section square to the line from end to end:
- profile: a built-in profile, or profile_sketch, a sketch whose material
(nested loops alternating, so two circles make a tube) is the section in
its own x and y around its origin; profiles picks override it.
- anchor (origin, centre, centroid or a bounding-box corner or edge middle),
angle (an angle expression, so a parameter), mirror.
- Orientation: the profile's y as near world up as the line allows, x
square to both; a vertical member's x is world X (frame::member_axes).
- Members follow sketch and parameter edits, undo as one step, save and
reopen (format: pending/frame-members.rs), and are named after the profile
(Rect Tube 40x40x3, (2)…), numbering on past names already taken.
Tests against hand-computed volumes and bounding boxes (rectangle, 3D
tower lines, parameter edit, sketch tube profile and picks, anchor/angle/
mirror), refusals, undo/redo and reopen; walk fixtures and goldens; docs.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Frames: fixes from the adversarial review (#4003)
- Default member lines are what was drawn: projected and other linked curves
and 3D wires (a face sketch's edges) and lines of no length are left out.
- A profile sketch's material starts from its drawn profiles, as
solid.extrude's "all" does, so a section sketched on a face works; the
even-odd test uses outlines and boxes worked out once, capped at 256.
- Member names are pinned to their lines (`names`, by line id; `body_name`
is the base): deleting or adding a line, or deleting another feature, no
longer renames other members, and frame.member stores every name it gives.
body.rename renames a member on its line (also for later member features);
a copy whose body_names were set still names its members by position.
- Built-in profile dimensions are expressions (ProfileSpec): they follow
parameters, bare numbers take the design's units, and they are feature
inputs. frame.profile.properties/insert read them the same way.
- Default root/toe radii shrink to the room a thick section leaves; radii
given are checked by name; a radius must be 0 or at least 0.01 mm; error
messages report the wall or flange value given, not twice it.
- A line within 1e-6 rad of vertical orients as vertical, so rounding never
turns a post a quarter turn.
- A 2D frame sketch in a differently placed component is mapped into the
member's frame, and member features recompute when placements change.
- Caps before lookups for a design's `lines`; a line listed twice is
refused; a 3D wire that runs back on itself is not a line.
Regression tests for each, from the review's scenarios.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Frames: the Frame Member dialog on the ribbon (#4003)
- Frame Member (MODEL > Create) opens a dialog: the frame sketch's lines
picked in the view (or All Lines), a built-in profile and its dimensions or
a section picked in another sketch, anchor, angle, mirror and name, with a
live preview. Edit Feature reopens it filled in.
- Lines picked in the view keep their sketch (a SKETCH_LINES input picks
ExternalSketchCurve): line ids are each sketch's own, so two 3D sketches
both have a `w2`, and the members went on the newer sketch's lines.
- timeline.redefine takes frame.member. Members keep their names through an
edit unless it gives them a new body_name; frame.member takes `names`.
- A member whose section is a whole profile sketch keeps it when edited
(the dialog shows the sketch instead of picking every region, which would
fill a tube's hole).
- An original frame_member icon, open for review, on the ribbon, timeline
and browser.
- The angle profile is listed as L-Angle, and web and flange as Web/Flange
thickness, so they translate apart from the existing Angle, Web and Flange;
the dialog's labels are in en, ja and zh. en-GB no longer repeats the frame
command labels it spells the same.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #4353
* Renaming a plane keeps its projections, canvases and hidden state (#4353)
timeline.rename only renamed the feature in other features' references. A sketch's
projection of a construction plane, a canvas placed on it and the hidden list keep it
by name too, so they lost it: the sketch warned that the plane no longer exists, the
canvas left the view and a hidden plane showed again. Document::rename_feature_keys
renames it in sketch links and canvases, as rename_body_keys does for bodies; the
selection follows in the command, and the hidden list in Session::refresh_from, so a
hidden plane stays hidden through undo and redo too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
timeline.rollback / timeline.roll_to read a negative position as 0, so
an agent passing -1 for "one step back" rolled the whole timeline back
and every body disappeared, with no error. A negative position is now
refused. The two commands shared one function that refused in
roll_to's name; each now refuses in its own.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Dropping a feature just behind the history marker now rolls it back, and
dropping it just before the marker makes it active again, in both the
bottom strip and the left panel. timeline.reorder and timeline.move_many
take an optional `active` param that sets the marker in the same command,
so the move is one undo step and one recompute. A position on the wrong
side of the marker for the requested `active` is refused.
Drop feedback:
- bottom strip: the drop line sits centred between two features (it
used to touch the previous one) and shows at the first position
(it used to be drawn outside the strip there)
- left panel: a drop slot below the marker when it is at the end
- no drop line when the marker is dragged back to where it is
- a dragged feature is outlined in the drop line's green
- grab cursor on the marker, grabbing cursor while dragging the marker
or a feature
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #3567
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019Yz6dHZiXcgTgrxjVNC6hx
* Edit Offset Plane: keep a face base, refuse a plane on itself (#3567)
Reopening an Offset Plane built on a face looked the face up at the
plane's origin, which can lie off the face, so the Plane input came up
empty. Look it up at the point picked on the face. A redefine that
builds a feature on itself is refused with a plain message instead of
failing with "plane offsets nested too deeply".
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019Yz6dHZiXcgTgrxjVNC6hx
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #2678
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* WIP: timeline.dependents shares the evaluation cache (#2678)
The check before a delete evaluated the edited design on a fresh model:
it recomputed the whole timeline and left nothing for the delete. It now
evaluates on a copy of the session's model. Adds Ahead::replies for
running such checks off the window thread (the UI part is still to come).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Delete: check what a delete breaks off the window thread (#2678)
Both checks a delete makes first (timeline.dependents for the timeline's
Delete, the selection.delete dry run for Delete on the selection) evaluate
the history after the deleted feature, on the window thread. A part with a
slow feature froze the window for as long as everything after it took
(5.9 s in the report). They now compute off the window thread like undo and
the history marker: within the app's 150 ms wait they carry on at once,
otherwise the window says it computes and the delete (or the confirmation)
follows when the report is in. A design changed meanwhile is checked again;
a second Delete meanwhile is left out.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* ci: run the checks again (the run for 3b94e8e0 was cancelled when the PR left draft)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* feat(geom): surfaces through curve networks, and spline spaces to build them
Adds spline_space (clamped B-spline spaces, Hermite interpolation, exact
embedding by Bézier degree elevation and knot insertion, a monotone cubic
for reparameterising) and network (loft, Coons and Gordon surfaces through
curves in one or two directions, with G1/G2 cross-boundary conditions
against a neighbouring face). Part of #763.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* feat(kernel): boundary surfaces from sketch curves, 3D curves and edges
kernel::boundary_network turns sketch chains, 3D sketch polylines and edge chains
into network curves, gives G1 frames of the faces along open edges
(EdgeFaces), builds the B-spline face (sides split at chain vertices so a
join shares the body's edges) and joins it into a surface body by stitching.
G2 is refused for now (not supported yet). Part of #763.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* fix(kernel): second derivatives of B-spline surfaces in the vendored truck-geometry
BSplineSurface::uuder and vvder multiplied the second differences by p
instead of p·(p − 1), as BSplineCurve::der2 does, so every surface of
degree p ≥ 3 (NURBS too, through its homogeneous surface) reported
1/(p − 1) of its second derivative: a cubic surface's curvature read as
half. This is why a G2 boundary surface on a cylinder measured half the
curvature it carries (#763). New tests hold both to finite differences
for degrees 2 to 5.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* feat(kernel): G2 boundary surfaces against a body's face
The network always carried the face's curvature across a G2 edge; the
refusal came from measuring it with truck's halved surface second
derivatives (fixed in the previous commit). EdgeFaces now reads the
face's second fundamental form from the exact second derivatives
instead of differencing the normal. A new test holds the curvature
across a cylinder's edge to the cylinder's within 0.1%, also with a
sheared far curve; G3 is refused (a network holds up to G2).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* test(kernel): a boundary patch with straight corners measures its own area
A stadium's arcs meet its lines at 180°, so the Coons patch is singular
at its corners. From such a corner the reference mesher's boundary walk
ran onto the B-spline's extrapolation past its domain (a planar spline
passes through every point of its plane there), and the face measured
289 mm² for its 158.5 (#763). The vendored mesher's bounded projection
(nearest_projection, #2043) keeps the walk on the domain; this holds it
there, by the faces, the measuring mesh and the display mesh. The
display path (#1653) was never affected.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* feat(geom,kernel): three-sided boundary surfaces (one side collapsed to a point)
A network curve may be a PointCurve: the apex where the two sides beside
it meet. The curves through it cross it at the point itself, its row of
the net collapses there, and the kernel's face leaves that side out of
its loop (three edges, one vertex at the apex). One point per patch, as
a side; refused elsewhere, when it moves, or with a continuity
condition. Tests: a triangle and a quarter disc filled flat with their
analytic areas (40 mm², 25π), by geom and by the kernel's faces and
meshes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* feat(doc): boundary surfaces through curve networks and loops of three or four
FeatureKind::SurfaceNetwork saves a network as `u` and `v` curves, each
a sketch chain (planar or 3D), a chain of a body's edges with an
optional G1/G2 continuity, or a point (the apex of a three-sided
patch), and an `operation` that can join the surface into the body of
its edges. A SurfaceBoundary of three or four sketch curves, refused
until now, builds as the flat Coons patch of its loop (three collapse
the side opposite the first curve). The format change is one pending
file; feature-walk goldens record the new variant's sketches, bodies
and points.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* feat(engine): surface.boundary through loops of three or four and curve networks
The command keeps its loop form (two to four curves of one sketch; three
and four now build the flat patch of the loop, crown refused there) and
gains a network form: `u` and `v`, each curve a sketch curve id, a
{sketch?, curves} chain (planar or 3D), a {body, edges, continuity?}
edge chain (g1/g2 with the face beside it) or a {point} for a
three-sided patch, with `operation` new or join. Edits may move between
the two forms (timeline.redefine accepts the command now that it has a
dialog).
Tests: analytic areas of loop patches and of a hyperbolic paraboloid
bounded by four 3D lines (every mesh vertex on z = xy/10), a loft
across two sketches, G1 and G2 measured across a cylinder's edge with
inspect.continuity (angle < 0.1°; curvature jump 1e-16 with G2 against
0.027 with G1), 26 hostile networks refused without panicking, and u/v
added to hostile_params_never_panic.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* feat(ui): Boundary Surface dialog
Curves and Cross curves take sketch curves and edges (picks that meet
end to end in one sketch or body are one chain); Continuity and
Operation (New Body or Join). Two to four sketch curves of one sketch
with nothing across are the loop patch; anything else is a network.
Edit Feature brings either back (per-side orders, crown and stations
the dialog does not show are kept). Strings in en, ja and zh.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* docs: ROADMAP M8 and the bridge patch's notes for boundary networks (#763)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* test(oracle): a boundary surface through a loop, thickened (#763)
Case 83: four sketch curves (a square's three sides and a half circle
for its top) make one boundary surface, thickened 2 mm; analytic values
from tools/oracle-analytic/cases_surfaces.py (V = 2A, area 2A + 2P,
centroid by moments). Recipes gain boundary_surface, thicken and remove.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* refactor: boundary surfaces, review cleanups
Project onto the face once per derivative evaluation (the frame is
passed to natural() and reused by scale()), keep each track's
finite-difference step instead of rescanning its table, export the
kernel's edge-pick and chain caps and the default station count for
the engine, doc and dialog to share, map TooLarge spline errors to
KernelError::TooLarge, reuse the engine's operation parser, and skip
the dialog's sketch lookup when the picks are no loop.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
A field the definition doesn't have is refused with the fields it does have, instead of reporting success and changing nothing (#1491).
Co-Authored-By: Erikas <erkexzcx@users.noreply.github.com>
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
A symmetric solid extrude of 10 mm is now 10 mm thick, 5 mm each side of the sketch plane, and switching from One Side to Symmetric keeps the thickness entered. Under format 21 the extent records its convention; designs saved without it keep the per-side reading, so their geometry and parameters don't change. Fixes#1236.
Co-authored-by: Karl-VonRichter <Karl-VonRichter@users.noreply.github.com>
render.settings.set saves validated named render setups (camera, output size, exposure, environment) as one undo step, and render.settings.get reads them back without applying a camera. When validated render settings are the only change, the engine keeps the evaluated model instead of rebuilding it. Setups are saved under design format 21; format-20 designs read as having none. Fixes#658; refs #620.
Contributed by @0xlillith.
Co-authored-by: lillith <35337584+0xlillith@users.noreply.github.com>
Adds sheet.perforate: round holes on a staggered or square grid over the flat sheet, kept clear of edges, cut-outs and bend zones. The holes go to the flat pattern, the DXF and the measured volume rather than the B-rep, so a panel can carry many thousands of them.
Fixes#928. Extrude To / From Object and Revolve To Object now resolve their target in the feature's own component frame, so a face in another component whose occurrence is moved is found where it is shown instead of the extrude stopping at a flat plane through the picked point. The point is named after the nearest face, a named point keeps its named face when another component touches it there, and such features re-evaluate when a placement changes, so they follow the target when it moves later.
Co-authored-by: SychPL <SychPL@users.noreply.github.com>
Fillet gets a Curvature (G2) radius type (type: "curvature", alias "g2"): a quintic blend whose size is the equivalent circular setback, for convex and concave straight edges between planar faces with a perpendicular planar end face at each end. Unsupported cases are refused rather than falling back to a circular fillet, and a blend that would cross a loop in its end face is refused. Persisted as a fillet style under format 19; labels in en/de/ja/ko/zh.
Co-authored-by: midasdf <midasdf@users.noreply.github.com>
The feature history can sit in a panel on the left, with folders that hold one unbroken run of features, drag and drop as one undo step, and a resizable divider. Timeline folders save under format 17.
Convert to Sheet Metal now takes a solid or a shelled body by its bend edges (`bends`): the faces reached from the fixed face across those edges become the sheet, keeping the part's envelope, with the flat pattern by the rule's K-factor and radius. Other edges between sheet faces are cut open. The result works with edge flanges, cuts, Unfold/Refold, the flat pattern and DXF. A conversion without `bends` is the plate conversion as before. The optional `bends` field is noted under format 17. Fixes#647.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
One edge flange feature gave all its flanges one height and one angle. A
part whose flanges lean differently took one feature per angle, and
flanges of separate features don't close toward each other, so its
corners stayed open.
- sheet.flange (edge): an entry of `edges` is a point [x, y, z] as before,
or {point, angle?, height?} whose angle and height (expressions, checked
like the feature's) replace the feature's for that edge. Bad input is
refused with the edge named. Before, the object form was read for its
point and the rest was ignored without a word.
- The feature stores its edges as FlangeEdge. An edge without values of
its own is written as the plain point it always was, so designs without
them are read and written as before; an unknown key in an edge is
refused, not dropped.
- The edges' values are feature inputs of their own (Edge angle, Edge
height, after the feature's), so parameters, renames and
parameters.change reach them. timeline.edit names the edges again when
it changes them, so each value stays with its edge.
- SheetBody::add_flanges_each trims every edge by its own setback and
adds the flanges. The corners between them close as between equal
flanges: the closing already works from the two flanges it joins (each
one's fold and leg), so the flat pattern follows by hand from the
angles, the heights and the rule (the tests derive it).
- The Flange dialog shows a row per picked edge with an angle and a
height box (empty: the dialog's value) once more than one edge is
picked, and brings them back on Edit Feature.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>