Commit Graph
635 Commits
Author SHA1 Message Date
jyvikoandClaude Opus 5.5 5c45570c91 Kernel rig: rustfmt; measured values in results are decimals, within tolerance; the ladder records 06/023 passing
The single results form compares a whole number exactly (a count). The construction and inspect
cases gave positions and volumes as whole numbers, which the form they were written for compared
within tolerance; they are decimals now. The NPT groove fix makes ladder 06/023 pass: its golden
entry is the passing run (51 faces, 8226.4042 mm3).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 6af622978a Threads: a taper thread's groove follows its crest cone across the section, so no sliver of the flanks is left
The groove's section was cut square a fixed margin past the crest. The crest cone changes 1 in 32
along the axis across the section's own width, so for NPT (margin 0.015 mm against a 0.028 mm
rise) the section's deeper corner stopped under the cone and each tooth kept a sliver of its
flank: 0.94 mm3 too much on a 1/2-14 NPT. The section's edge now follows the cone at the same
margin.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 21:08:31 -04:00
jyvikoandClaude Opus 5.5 7664925fbf Sketch: Project onto Surface keeps the side the projection meets first, in one curve
SMLib's parallel projection (CreateParallelProjectionCurves) gives every curve where the
projecting lines cross the face: a line projected down onto a ball came back as its top and its
bottom, each split at the pole, and the link's first wire was half the bottom. A projection onto
a surface is where those lines first hit it (owner's decision, as mainstream CAD does): a curve
is now kept only when the first hit on the body's mesh along the line through its middle is the
curve itself (within 4 chord tolerances), and the pieces that meet end to end are joined in
whatever order and direction they come, a piece run the other way exactly (its knots and
control points reversed; a line's, circle's or ellipse's parameter mirrored). The ball's top
is then one wire from x = -10 to 10.

three_d_sketch_curves now expects that exact curve: one wire, its ends at (±10, 0, √300), every
point of its exact curves on the sphere of radius 20 in y = 0 over the top, to the projection's
own tolerance (a millionth of the body's size), and sweeps_and_pipes_follow_3d_sketch_curves
pipes along the whole joined top. Both pass on the pinned SMLib (90aabff): the pieces lie 9.1e-6
off the sphere against a 4e-5 tolerance and meet at the pole within 4.7e-8 rad, since the fork's
8d95600 keeps the pole's exact tangent in StepBackFromSingularity.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 19:40:02 -04:00
jyvikoandClaude Opus 5.5 ac70662d63 Sweeps: a path through a drawn 3D arc follows the arc, not a spline through its three points
path_points took any wire with three or more fit points as a fitted spline, and a 3D arc keeps
its start, through and end points as its fit: the pipe along a quarter arc of radius 20 ran
along the cubic through those three points and came out 388.06 mm³, not π·2²·10π = 394.78.
A wire with its exact arc (Wire::arc) now goes to the kernel as that circle, from its start
counter-clockwise about its normal through its sweep (kernel::curve_path of the record circle).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 19:39:40 -04:00
jyvikoandClaude Opus 5.5 b2c5b1f5e9 Designs before format 14: a split's pieces take the names its later features use them by
Builds before format 14 named the pieces a cut splits a body into in truck's shell order, and
the later features of such a design name the piece they work on by that name. SMLib orders the
pieces otherwise, so split-body-pieces' fillet and chamfer landed on the wrong piece, its
reference "no longer exists" (design_corpus body_names_saved_before_exact_history_keep_their_pieces,
old_designs_open_and_evaluate_as_saved). For a feature saved so (`shell_piece_order`), each
name its pieces are known by goes to the piece the points the later features naming it picked
lie on; a name no later feature uses keeps SMLib's order, and so do all of them where the picks
do not tell the pieces apart. docs/compatibility.md says so.

That makes the feature's result depend on features after it, which neither its fingerprint nor
its cache key cover: a script replays the design one feature at a time, so the split was
evaluated before the fillet and chamfer existed, kept SMLib's order, and was reused once they
came (script_roundtrip corpus_designs_replay_from_their_scripts: 'Body1 (1)' 4765.663706234679
opened against 4765.663706134907 replayed). The state now keeps a digest of the picks it named
the pieces by (`ModelState::legacy_picks`), and every reuse (the last results, the cache, the
kept, rolled-back and primed results) takes a state for such a feature only while the design's
later features pick the same, so the replay names the pieces again as the file does when it
opens. A saved model's states carry no lineage and are taken as saved.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 12:16:22 -04:00
jyvikoandClaude Opus 5.5 426a505a87 Display meshes: tests count the planner's grids; a mesh's outline is one line per straight edge
The display mesh is the tessellation planner's (8b6bfc48c: the mesher plans a schema 4
record), which grids a planar face with no side longer than a fifth of the body's extent
(docs/capabilities.md, "Display meshes"); truck's mesher gave a box face two triangles. The
tests that counted truck's mesh now count the planner's, worked out by hand from that rule:
- a 10 x 20 x 30 box (37.4 mm diagonal): edges in 2, 3 and 5 pieces, faces of 2 x 3, 2 x 5
  and 3 x 5 cells, 124 triangles; welded, the box lattice's 3 x 4 x 6 nodes less the
  1 x 2 x 4 inside it, 64 positions (obj_export_is_welded_and_keeps_names);
- a 20 x 15 x 10 box: 4 x 3, 4 x 2 and 3 x 2 cells, 104 triangles (an_opacity_class_change...);
- a 20 x 20 x 10 box saved as a mesh: its edges in 4 and 2 pieces, 40 segments per box
  (imported_mesh_edges_draw_in_each_style...);
- the cylinder's top cap is under a third of its triangles (select_other_over_a_dense_cluster...).

An imported mesh's outline was one line per crease side, so a box exported at that spacing
showed each edge in pieces: a click on a 10 mm edge measured 5 mm, or hit the node between
two pieces (measure_imported_stl_edges_and_vertices..., mesh_outline_hover_cache...). Outline
sides that run straight on through a vertex no other outline side meets are now one line, as
the CAD model's edge was.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 12:16:22 -04:00
jyvikoandClaude Opus 5.5 983b1ca8f0 Sketch projection: a projected face's curves meet at the face's vertices
A face's edges are projected exactly: lines, and arcs read off SMLib's NURBS within the
planar-edge tolerance (Body::planar_edges). An SMLib shell's offset corner is a NURBS whose
arc came out with its centre 2e-6 mm off and its ends up to 6e-7 mm from the lines they meet,
beyond the link's merge tolerance (1e-7): the inner loop of the sensor enclosure's case top
projected as sixteen loose curves, the offset of one found no chain to follow, and the Lid lip
extrude found no profile l13..a16 (the five acceptance scenarios, action_matrix
an_axis_through_a_corner_round_that_a_parameter_moves). Each edge's pieces now end on the
edge's vertices where they lie within the edge's and the reading's tolerance of them (the
vertex is the point both edges share), and an arc whose ends moved takes the centre nearest
its own that is equally far from both, so the sketch keeps both ends on its circle.
Body::planar_edges_tolerance names the reading tolerance planar_edges uses.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 12:16:22 -04:00
jyvikoandClaude Opus 5.5 5547cd98ad Blends: a picked edge is named as the blend takes it, the rim and not the seam
A chamfer picked at (10, 0, 20) on a cylinder's top rim lies on the vertex where SMLib's
cylinder has its seam. The blend takes the rim there (blend_smlib::resolve: a seam or a smooth
join loses a tie), but the name stored with the feature came from the nearest mesh edge, the
seam (`F2:side:c1`). Once the stem grew, the name found the seam and SMLib refused the chamfer
(join_extrude_from_a_chamfered_top_face). edge_names_for names the edge each pick takes as a
blend takes it (kernel::blend_edges), the nearest edge only where that finds none.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 12:05:37 -04:00
jyvikoandClaude Opus 5.5 5cc0d5e9c4 Threads: a metric size without a coarse pitch suggests its fine pitches again
The thread forms (b4549d270) parse designations in thread_forms, whose refusal for a plain
M28 said "give it: M28x1" and, for M0 or M1e9, still offered a pitch. The hint the hole
command gave (the two coarsest ISO fine pitches that suit the diameter: M28x2 or M28x1.5) is
now thread_forms::no_coarse_pitch, used by both; a diameter no metric thread has is an
unknown metric thread. The test's "unknown thread" follows the forms' wording ("unknown
metric thread").

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 12:05:37 -04:00
jyvikoandClaude Opus 5.5 60f33f6fc6 Feature walks: Repair Part has its fixture, its gap an input and its body renamed with the rest
#8676 added FeatureKind::Repair without a fixture, so
feature_walk_tests::the_record_covers_every_variant failed. The fixture sets
every field (body, gap, patch_holes); the records, written with
FEATURE_WALK_BLESS=1, show its one input (Gap, a length) and that copying with
bodies renamed rewrites its body.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 07:14:45 -04:00
jyvikoandClaude Opus 5.5 0ec97c5708 Blends: tangent propagation off blends the picked edges alone; a refusal says how to change it
The Fillet and Chamfer features already blend each picked edge's tangent chain
by default (tangent_chain, true unless saved false), as mainstream CAD's
tangent propagation does; the kernel blends exactly the edges it is given.
#8678 refused, before SMLib, every edge that runs on tangentially into one left
out, which also refused blends SMLib builds (a round ending on the round its
edge runs into: blend_corner's a_round_next_to_a_round_of_another_radius, the
same feature with propagation off). Now:
- propagation off: only the picked edges are blended; where SMLib cannot end
  the blend at such a continuation, its refusal names the edge it runs into
  and that propagation (tangent_chain: true) blends the chain as one;
- propagation on, where the chain cannot be built (an r3 round carried on
  round an r2 round's end arc), the refusal says the chain was blended and
  that with propagation off only the picked edges are.
A smooth edge is still refused before SMLib. No default changes: the feature's
default was propagation on already.

The kernel tests that stand for a Fillet feature (curvecorner's sequential
rounds, issue 2422) take each pick's tangent chain, as the feature does by
default.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 07:14:45 -04:00
jyvikoandClaude Opus 5.5 f351f42df6 Repair Part: the repair runs once, as the feature evaluates
The command worked the repair out itself for its reply and the feature worked it out again
when it evaluated. The evaluation now keeps the kernel's report on the feature's result (as
an import keeps its import report, cached with it), and the command's reply is built from
that: one repair per call, and a part with nothing to repair fails the evaluation, which
leaves the design unchanged.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 00:29:59 -04:00
jyvikoandClaude Opus 5.5 7c8132e2d6 Repair Part (body.repair, #8371): rebuild refused faces, sew gaps, patch holes
A new undoable feature (`repair`, one pending format file) and command with input and
output schemas. In order:

- A cylinder, cone, sphere or torus face SMLib refuses on its own is rebuilt on a NURBS
  form of its surface laid on arcs from where the face starts
  (`form::surface_on_own_arcs`), with SMLib's own trims: the import's quarter-grid form of
  a face round most of a turn closes on itself, which SmTorus::IsNurbSurfaceTorus does not
  recognise. Geometry unchanged.
- Free edges that pair up within `gap` are sewn by SMLib's stitch; GlueEdgesGeneral gives
  each glued edge its own tolerance (at least twice its gap), the body's and the other
  edges' stay. The result is checked against the input's own SMLib check, the
  tolerance-bound tests (#5, #6, #59, #82) exempt.
- Loops of free edges left are holes: offered as surface.patch, and with patch_holes made
  (flat only when the loop is planar and every face around it is a plane, else G1) and
  sewn in.

The reply reports what changed face by face; nothing to do is refused with why.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-29 00:29:59 -04:00
jyvikoandClaude Opus 5.5 5d25684a13 sheet tests: the flat pattern as SMLib's exact 2D boolean makes it
Three expectations encoded the old truck planar booleans' incidental output;
each is replaced by the exact answer:

- a_base_trimmed_for_a_flange_keeps_its_arcs: the flat outline has 10 edges,
  not 12. The flange's bend zone and panel meet in line, and the union of
  the two is one line along each side (a region's boundary has no vertex in
  the middle of a straight run). Lengths and areas are unchanged and still
  checked to 1e-9.
- a_base_trimmed_through_a_free_form_curve_follows_it_with_arcs, renamed
  ..._keeps_it_exact: the trim cuts the parabola exactly, so the base keeps
  one conic and three lines instead of tangent arcs within 0.001 mm. The
  strip (183.564 = ∫ y from 197 to 200, or 600) and the bend's length
  (62.364) are now checked to 1e-6 and 1e-9 instead of 0.22 and 2e-3; the
  chorded comparison stays.
- pockets_with_free_form_outlines_are_machined_beside_free_form_cut_outs:
  the machining record holds the pocket's four exact conics in their order,
  started at another of them; the check is for the same closed loop, not
  the same first segment.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 22:12:07 -04:00
jyvikoandClaude Opus 5.5 068c6a6dcb Shell certificate tests: the saved strips are saved data, not rebuilt pieces
Two tests rebuilt the old kernel's raw strips (a shell's wall split along its
opening, a stepped tab's -x wall split by the Join and the Cut) with today's
kernel and took the saved piece's name and projection from them. SMLib leaves
those walls one face, so there is no strip to rebuild: the tests now say so (the
wall is one face) and give the saved link as what an older file holds, its piece
name and its rectangle (y 10..20 x z 0..20 on the -x wall, the same 4-line
projection the strip had), and keep every check of what the model does with it.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 22:11:55 -04:00
jyvikoandClaude Opus 5.5 c37b0d2f02 Kernel rig: a case's expected continuity order at its blend seams
expected.json may give `continuity: {order: g0…g4, edges?: "blend" | "corner"}`: the
seams of each round, chamfer face or corner patch with the faces either side of the edge it
replaced, and of each corner patch with its rounds, are measured as Continuity Analysis
measures them (seam_diagnostics at its default 33 stations and default tolerances), and the
case fails naming the worst seam, its faces, the order it reaches and the next order's worst
value. The seams come from the faces' persistent names (doc::naming::blend_seams). The older
`{near, within_mm, …}` form is kept.

Every fillet-area case with a body gets its order: constant rounds and rolling corners g1,
curvature rounds g2, chamfers g0, the corner: g2 patch g2 at its seams.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 21:22:17 -04:00
jyvikoandClaude Opus 5.5 c070f044ab STEP import: a torus face round most of its tube is formed within one turn of it
A torus face covering most of its tube off the tube's quarter lines (an
exhaust collector's bend: 326° of the tube from −113.8°) needed a fifth
quarter along the tube, which STEP counts from the outer equator: its form
ran past a full turn of the tube and SMLib refused the solid. #8496 turns
frames about the axis only, and the torus label had no tube reference.

The torus label gets a tube start (`tube_start`, radians; 0 and left out
of the record by default, so older records mean what they did): v counts
from there, in every evaluator, form, pcurve, iso curve, tessellation,
placement, SSI and SMLib transfer. A spilling torus face's tube start moves
to where its tube begins, or a turn before where it ends, whichever puts
its tube circles on the grid of a round face they are about the axis of
(a pipe's cylinder meeting the bend); circles round the tube are labelled
from the tube start (brep::form::on_tube), so their forms and pcurves lie
on the face's quarter grid exactly. The saved-format change is one file,
crates/doc/src/format/pending/torus-tube-start.rs.

Engine assembly: COLLECTOR_EXHAUST_VER_1 now comes in as a closed solid
(refused 3 -> 2); Poppy Humanoid unchanged (4).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 21:22:11 -04:00
jyvikoandClaude Opus 5.5 920acc5279 STEP import: the feature's warning says in words what became of the parts
The kernel's import warnings get a structure (ImportReport: the file's parts, how many came
in as solids, and each warning's kind, part, faces and count; the reads' notes are typed as
repairs or faces left out). The Import feature's result carries it (and the model cache keeps
it), and the timeline tooltip and the status line after an import word it from the catalogs:
"Imported 40 of 43 parts as solids. 1 part couldn't be made into a solid and is shown as a
mesh. 3 faces couldn't be repaired and are missing." with what may help. Entity numbers and
the kernel's wording stay in Copy Warning Message, which now lists every warning.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 15:58:06 -04:00
jyvikoandClaude Opus 5.5 c33bae8701 Section cap: only closed bodies take part in the crossing count
An open body (a surface body, a mesh that does not close) has no inside: its faces counted
with the rest took the cap from the closed body it lay in or behind. The body's closedness,
which the kernel knows (`ModelBody::is_closed`: no shell left open, a mesh body every side of
which two triangles share), goes with it to the renderer (`SceneMesh`, `PlannedBody`,
`InstancedMesh`, a block's closed runs, the loose open triangles), and the count draws closed
bodies only.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5Lzv2n8fyKqD61NCHSF
2026-10-28 15:43:35 -04:00
jyvikoandClaude Opus 5.5 912bccef65 Isocurve Analysis: faces on one surface share their lines
The held parameter was spaced over each face's own trimmed (u, v) box, so the pieces of a
face split by a boss showed different lines that missed each other at the split. The lines
now sit on a ladder of the surface: a bounded parameter's range in count + 1 steps, a linear
one (a plane's, a cylinder's or cone's axis) at a round world spacing from the world origin.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-28 15:02:54 -04:00
jyvikoandClaude Opus 5.5 cb8712aa09 Continuity: one table of orders G0-G4, and one check of what each construction builds
The kernel's Continuity moves out of bridge.rs into continuity_order.rs and gains G4. One
table holds each order's command word (g0-g4), its code (G0-G4, for tips and messages) and
the message ids of its label and hover text. Construction says which orders the patch,
bridge, network, match and sketch blend curve build today; Continuity::built_by is the one
refusal every command and kernel entry point uses. A design may now save g4 (format note).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 21:15:20 -04:00
jyvikoandClaude Opus 5.5 be859aa0d4 Isocurve Analysis draws each face's exact iso curves, cut to its trims (Refs #770)
The analysis sliced the display mesh with planes: faceted, approximate, and
broken at triangle seams and trims; the window drew it as a 2D overlay without
depth while the tool was active. Now one kernel routine (kernel::iso) clips a
surface's u = const or v = const line to a face's pcurve loops; the curve through
a point (sketch projection) and the analysis grid (count each way, evenly across
the face's extent) both use it. The loop polygon follows the loop's order (a
pcurve the loop runs against is walked backwards), which the inside test got
wrong before, and closes over vertex-loop poles.

ModelBody caches the lines per face, count and display quality. The session
keeps the picked faces as view state (inspect.isocurve add/clear, hostile counts
refused); the viewport, ui.render and snapshots draw them depth tested in the
accent colour. Curvature combs on faces follow the same exact lines.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 21:15:14 -04:00
jyvikoandClaude Opus 5.5 87e7fe472b Tapped holes: a preference keeps metric's major-less-pitch drill
New metric tapped holes drill the tap maker's drill (M8 6.8 mm). The Design preference "Metric
tapped holes drill the major diameter less the pitch" (`metric_tap_drill_major_less_pitch`, off
by default) gives them the drill every metric size took before (M8 6.75 mm): the Hole dialog
shows and sends it, and `solid.hole` given a thread and no `diameter` drills it, through the
session as `auto_project` is (kept when a design is opened or started, and across tabs). Unified,
pipe and taper sizes keep their tabulated drills; a given diameter is unchanged. Saved designs
keep the drill they stored either way.

Labels in en, ar, he, ja, zh, de and ko.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 05f1c6b9ac Tapped holes: the tap maker's drill for every form, and a drill of the user's within 5%
Every tapped hole now drills the tap maker's tabulated drill. ISO metric takes Yamawa YEU23's
drill size column for cutting taps (printed p.704, M coarse; pp.704 to 706, MF fine): M8 drills
6.8 mm and M12 10.3 mm, where the major less the pitch gave 6.75 and 10.25. A custom metric size
the table lacks keeps the major less the pitch. UNC/UNF (Guhring), G, Rp, Rc and NPT (Yamawa)
were tabulated already. The Thread command's suggested hole for a metric size follows.

The Hole dialog's Tap drill diameter is now a field, the tap maker's drill by default, and the
command's `diameter` with a thread is checked the same way: a drill is accepted from the
internal thread's standard minor diameter (or the tap maker's drill where that lies below it:
Rp, Rc, NPT) to 5% over the tap maker's drill. Outside that the command names the range and
why. The field's tooltip gives the drill, the minor diameter and the range. Presets keep a
chosen drill.

A saved design keeps the diameter it stored, so it builds as before, and editing such a hole
keeps its drill: no preference and no format change. Scripts that give a thread without a
diameter drill the new default; ladder 05/007, 11/003 and rig case threads/2115 follow
analytically, and their golden entries are re-measured from runs (tier 05 re-sorted by time).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 e7994d48cc Tapped holes: Rc and NPT take the tap maker's tabulated drill
The Rc and NPT drills were rounded to a drill series from a third-party reproduction of DIN 345
and a fractional/letter inch series cited from memory. They now come from the same tap maker's
catalogue the G and Rp drills do: Yamawa YEU23, printed p.709 (Rc, the maximum straight bored
hole with non-full threads, Rc 1/16 to 4) and p.710 (NPT, the maximum straight bored hole, 1/16
to 3). A size its tables lack (Rc 5 and 6, NPT 3 1/2 to 12) is refused as a tapped hole, naming
the range. The dialog's tooltip keeps the standard's minor diameter where the thread ends.
Rc 1/2 drills 17.6 mm (minor 17.807), 1/2 NPT 17.60 mm (minor 17.473).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 b6c3b32a98 Tapped holes: an Rc or NPT hole takes the stocked drill under its standard minor
An Rc or NPT hole was drilled to the exact minor diameter where the thread ends, a size no shop
stocks. It now takes the largest stocked drill not larger than that: metric drills of the DIN 345
series for Rc (to 100 mm), letter and fractional inch drills by 64ths (to 1 1/2 in, ASME B94.11M)
for NPT; past the series it is bored to the exact value. The Hole dialog's drill shows the inch
size for NPT, and its tooltip the exact standard value. Rc 1/2: 17.807 mm, drilled 17.75 mm;
1/2 NPT: 17.473 mm, drilled 11/16 in (17.4625 mm).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 9717fab2f3 Tapped holes: Rc and NPT, and a modelled thread with the thread's End
The tapped-hole catalogue takes ISO 7-1's Rc and ASME B1.20.1's NPT internal taper threads,
every size of the tables a modelled thread cuts. Their drill is the internal minor diameter where
the thread ends (the reference plane's minor at the face less the 1 in 16 taper over the useful
or effective thread length), derived from the standards rather than a tap maker's table. An
external R is still no hole's.

A tapped hole's options mirror the thread's: `modeled` cuts its thread into the wall, from the
entry, by the same cut as `solid.thread` (now one function both call), and `ease_out` fades its
inner end out before the bottom (ISO 3508); without it the groove stops square at the thread
depth, clear of a blind hole's bottom. The Hole dialog's Tapped rows add Rc and NPT, Modeled
and the End choice (Square, Fade, Fade Length). The format notes in pending/thread-ends.rs and
pending/pipe-threads.rs record the new keys and sizes.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 80e47130b9 Thread: the pipe forms in the dialog, ISO 7-1's Rp, a chamfered tip on a taper thread
The thread dialog offers the pipe threads: G (ISO 228-1), Rp (ISO 7-1), R and Rc (ISO 7-1) and
NPT (ASME B1.20.1). Their sizes are listed by designation without a pitch, one start and a hand
of right or left; a size picked for a hole the dialog sized Rc stays Rc.

Rp, ISO 7-1's parallel internal thread an R screws into, is a form of its own (`rp`): the
parallel profile (H = 0.960491 P) at ISO 7-1's gauge diameters, refused on a shaft. Its cut
meets the analytic material of its profile within 1e-5, as G does.

A taper thread takes a chamfered tip: each end's cone is measured from the major diameter the
taper has at that end. Pipe threads are not ISO metric, so they give chamfer_depth.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 5fe141c0f9 Thread: the start never fades; ease_in is gone
A thread's start runs off its free end, plain or chamfered; only its inner end fades out
(ease_out) or stops square. The `ease_in` field, the command parameter (refused now, naming
ease_out), the dialog's Ease In row and their docs are removed; `pending/thread-ends.rs`
drops a saved `ease_in` as the design opens. The runout test covers the short, standard and a
sub-turn fade at the inner end.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 361b35afee Thread: a shoulder thinner than the overrun's reach is still a shoulder
The free-end test looked for material 1 to 1.5 pitches past the face's end, beyond the first
pitch so that a chamfer the groove runs out through counts as free. A plate thinner than that
(a boss on a 1 mm plate under M10) had none there, so its top was taken for a free end and
the groove's one-pitch overrun cut into the plate (15 mm³ of a 1 mm plate).

An end is now closed when, over the overrun's whole reach, material lies outside the face's
cylinder (inside it, for a hole) at the radii the groove cuts beyond the face: a shoulder,
plate, head or blind bottom, however thin, steps out past the face, while a chamfer, neck,
countersink or counterbore steps the other way. The band test beyond the first pitch stays
for a cylinder that goes on past a split.

The regression test builds the boss as the app does (a rounded plate, a circle sketched on its
top face, extruded with Join) on 6 and 1 mm plates.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 75deb73aa7 Thread: ISO 228-1, ISO 7-1 and NPT pipe threads, taper threads by a radial law
Three forms: `bspp` (G, ISO 228-1, 55° parallel), `bspt` (R external, Rc internal, ISO 7-1,
55° taper 1 in 16) and `npt` (ASME B1.20.1, 60° taper 1 in 16). Their sizes are tabulated
from the public sources: ISO 7-1:1978 Table 1 (its gauge-plane diameters are the G sizes)
and NBS Handbook H28 (1957) Table VII.2; tests check every row against the standards' own
relations.

A taper thread starts at its free end with its standard diameter there (external: the gauge
diameter its gauge length in, internal: at the face). Its groove is the screw sweep with the
section moved 1/32 of the axial travel off the axis (the radial law the runouts use, added to
it), its section reaching just past the crest, and the material beyond the major cone (or
inside the minor cone) is cut with it, as a die or tap cuts the crests. An external one runs
its standard length by default.

The volumes are checked against the profile's material fraction integrated over the tapered
radii: G 1/2 to 2e-6, R 1/2, Rc 1/2 and 1/2-14 NPT within 0.2 % of the cut.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 2c4212c042 Thread: the chamfered tip at the start or at both ends
`tip` was none|chamfer, chamfer cutting every free end. It is now none|start|both: `start`
chamfers the end the thread starts from, refused when that end is not free (a shoulder, or a
stop inside the face), and `both` every free end as `chamfer` did. The dialog's Tip pick offers
None, Start and Both; `tip: chamfer` in a command names its replacements.

The thread's end options (runouts, tip, chamfer angle and depth) came without a format
change file; `pending/thread-ends.rs` records them and rewrites a saved `tip: chamfer` to
`both`.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 a30a85698f Thread: the chamfered tip reaches ISO 724's external minor diameter
ISO 4753's chamfered end bounds the end's diameter by the minor diameter. The default took the
modelled root (the basic d1) for it, so the cone's small circle lay on the root cylinder and
the chamfer ring pinched to nothing wherever the groove reached the end. The default is now
the external minor diameter d3 = d - 1.226869 P of ISO 724, below d1: the cone crosses the
root, each end is a whole disk of d3 inside a whole conical ring. ISO 4753 is for ISO metric
threads; the other forms, whose root is already their design minor, give chamfer_depth.

Ladder 06/017's analytic volume follows (1945.354522563); its golden entry re-measured.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 13:02:32 -04:00
jyvikoandClaude Opus 5.5 d8282b3361 doc, engine: corner: g2 sets each corner back for its G2 patch
FeatureKind::Fillet with corner G2 is kernel::fillet_g2_corners, its setbacks
the corners' distances (the rest 1.5 r); setbacks now go with either corner.
The engine's corner test builds the G2 corner, default and set back 7, one
closed solid of 10 faces within 0.1% of the ball corner's volume.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 12:24:10 -04:00
jyvikoandClaude Opus 5.5 9cd655259d Profiler: commands, feature evaluation, io; diagnostics.profile; CLI --profile
- Session::execute is a command span; Model::evaluate and each feature computed
  (by its type) are spans; io's import, export and design read/write too; the
  STEP reader's topology, pcurves and solid record.
- diagnostics.profile (contract + output schema): report, start/stop, reset,
  Chrome trace file.
- A STEP/IGES import's reply carries its own profile while recording.
- Every app compiles the profiler in by default (feature `profile`);
  SOLIDCRAFT_PROFILE=1 starts it.
- solidcraft-cli run/eval/bench-open --profile print the table on stderr,
  --profile-out writes the trace; run --profile works on designs and STEP files.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 11:40:49 -04:00
jyvikoandClaude Opus 5.5 d13300b0a1 cargo fmt: the format-40 change and the rebase's export list
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:33:33 -04:00
jyvikoandClaude Opus 5.5 8aea8e5a82 Format 40: a thread's hand on tapped holes too; v0.24.0's handedness opens as hand
v0.24.0 (format 39) saved a left-hand Thread or tapped Hole as `handedness: "left"`; this
branch replaced main's handedness (#4414) with the thread's `hand`, and features don't refuse
unknown fields, so such a design opened right-handed without a word. The pending format change
thread-hand.rs renames `handedness` to `hand` on Hole and Thread features (a `right` is
dropped, anything else refused).

Tapped holes take `hand` again, right or left (never both, and only with `thread`): the Hole
feature saves it, its thread is cut and annotated that way, solid.hole takes `hand?`, the hole
dialog's tapped rows have the thread dialog's Hand choice (without Both), editing a hole keeps
it, and hole presets save it under v0.24.0's `thread_options.handedness` key, so presets saved
by v0.24.0 recall it.

Test: a format-39 design with a left-hand thread and tapped hole opens left-handed; a hole's
`hand` refuses both and needs a thread.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 562a5bd337 Formatting: rustfmt over the rebased branch
cargo fmt --all, nothing else: code from the branch's commits and from the rebase's
resolutions that was not yet in rustfmt's layout.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HoZgkCdAVrscuw2kjQTWDs
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 5fc160732e Main's new callers of the placing calls that now return their error
Code main added since the last rebase reads the placed model, a camera or a scene
as values; on this branch they return Result. Picks and the edit dialogs read the
session's placed model through open_meshing::session_world, as the others do; the
revolve and circular-pattern axes, the model axis of a command and the warming of a
computed edit pass the error on; tests unwrap. A test meshing bodies uses
Body::mesh, the one mesher.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HoZgkCdAVrscuw2kjQTWDs
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 6b9f5e0e49 thread: main's screw direction (#4414) out; the thread's hand is the one direction
The reworked thread has its own direction, `hand: right|left|both`, on SMLib's
exact screw sweep. Main's #4414 added a second one, `handedness: right|left`, on
Hole and Thread, for the faceted groove this branch replaces. It is taken out: the
field, its pending format change (never released), the hole dialog's direction row,
its hole-preset option, its strings and its tests, which measured the faceted
groove. A tapped hole is right-handed, as before #4414.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HoZgkCdAVrscuw2kjQTWDs
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 a57ce13e70 thread: a shaft thicker than a modelled thread is refused, never turned down
A modelled thread never changes the size of the shaft it is on (#1018, #2853): a
shaft thicker than the thread is refused with the size to make it, as
tests/kernel-cases/threads/2705 expects ("this 14.6 mm shaft is too thick for a
modelled M14 thread; make the shaft 14 mm for M14"). This takes out the turn-down
of #4256: `thread_turn`, the fit that let a thicker shaft through, and its tests;
the 9 mm shaft refusing an M8 and the preview's M6 refusal on an 8 mm shaft are
back as they were before it.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HoZgkCdAVrscuw2kjQTWDs
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 cfc393d68f Main's new callers of the placing calls that now return their error
The branch's placement change (placing the model returns its error) made
world_state, home_camera, bounds, open_sketch_plane, the scene builders,
to_local and auto_operation return a Result. Main added callers of them
since the branch left it; they now take the error as the branch's own
callers do:

- engine: commands pass it on (`?`); helpers answering yes/no or "found"
  (snap points, a face's normal, the DXF export check) answer no for a
  model that cannot be placed. Frames keep the session for main's lazy body
  frames (#6356) beside the placed model the picks are on; a library apply
  maps its targets on that placed model. Before an extract or a link is
  replaced, the placed model is taken or the command fails.
- ui: panels, picks, dialogs and previews read the placed model through
  open_meshing::session_world (none when it cannot be placed: the viewport
  says why); Home and Fit frame nothing then.
- cli: the usage table is main's, with kernel-cases in it (a resolution of
  the rig's commit had kept the branch's whole file).
- tests read the Results with unwrap, and main's tests of Body::tessellate
  mesh through Body::mesh. Main's test of saved boolean retries goes (the
  branch saves none), as does the thread half of its dialog rendering test
  (the branch's thread dialog has its own); the tapped hole half stays.
- What no caller uses after the merge goes: a mesh body's span, the metric
  thread refusal text, and the revolve's targets-as-shown model (main used
  it for the coplanar run-on the branch removed). Main's SolidWorks Y-up
  test reads the exporting system's name (the branch's STEP header has no
  preprocessor or description fields).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 d63aa814f4 threads: main's tapped-hole sizes and shaft turn-down on the reworked thread
Main gave the Thread feature two things the branch's thread rework (forms,
hands, starts, extents, runouts, tips on ThreadAsk) was written without:

- Tapped holes take catalogue sizes (ISO metric and the catalogued UNC/UNF,
  G and Rp sizes): `ThreadAsk::tapped` reads the designation from the tapped
  catalogue, names the thread as the catalogue does, and fits a size that is
  not metric to the hole drilled for it (its tap drill). The hole feature
  asks for its thread this way.
- A modelled external thread on a shaft thicker than it turns the shaft down
  to its major diameter first (#4256): main's `thread_turn` makes the ring,
  the shaft is cut by it, and the grooves and a chamfered tip are cut at the
  turned radius. Such a shaft fits the thread.

ThreadInfo keeps the radius of the face it is on, which main's cosmetic
thread display draws at (0 in a state saved without it).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 9138e87040 Rebase onto main: what the merged code needs to build together
The branch rebased onto main keeps each of its commits; where both sides
changed the same code, these are the pieces neither side's commit had.

- Cargo: one [features] table in the CLI's manifest (two met in the merge).
- geom: a NURBS surface's `closed` set once in a placed copy (both sides
  added it).
- kernel: the whole-face extrude tools (#2040) work around truck's boolean
  on truck types, which left the workspace with the SMLib kernel; the
  module, its tests and the doc crate's tool and tests go. The display
  planner's flat fill (tess/fallback.rs) has no caller with the schema 4
  mesher, and the tessellator's seam and uv modules are the branch's. A
  body's boundary tolerance from a STEP file belongs to the truck body the
  schema 4 record replaced: `with_boundary_tol` goes. `unmeshed_faces`
  counts the coarse mesh as the branch does. A loft's section re-split
  passes the lead's perimeter shares to main's `resample` (a circle breaks
  there when the matched corners do not go round in order). Main's tests of
  the mesh-based measure (the SMLib kernel measures exactly) and of the
  IGES preprocessor name (no such field on the branch's import record) go.
- doc: a feature result carries no boolean diagnostics on the branch, so
  the model cache neither writes nor reads them, and a pattern copy's miss
  test runs the intersect as it is. A placed body's worker result is a
  Result: a body taken from the previous placement is Ok. A thread's
  clipboard remap takes main's arguments, the tapped catalogue names a
  metric size by ThreadForm::Metric, and main's tests unwrap the placing
  calls that return their error.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 c854239d18 doc, engine: solid.fillet setbacks: [{vertex, distance}]
FeatureKind::Fillet gains setbacks (serde default: none, omitted when empty),
each a corner vertex and a length expression; a fillet with setbacks is
evaluated by kernel::fillet_setback. Constant-radius exact fillets with
rolling corners only (refused otherwise, in the command and in evaluation).
One distance per corner: SMLib keeps one setback per corner, not per edge.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 fdede5a0ae Thread work in rustfmt's layout
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 d433ce2c9f Thread runouts: the groove fades out instead of stopping square
Ladder 06/009 had no way to ask for one: "solid.thread has no runout (vanishing thread)
length". With SMLib's smlib_screw_sweep_radial (replay e7acea1):

- smlib: the FFI binding and Brep::screw_sweep_radial, the profile moved off the axis by a
  piecewise linear law of the turn; crate test: a tooth moved out 1 mm over three turns has
  A 2π (c turns + ∫ offset dt).
- kernel: sweep_helix_radial, sharing sweep_helix's checks (helix_profile).
- doc: `ease_in`, `ease_out` (a length, or ISO 3508's standard 2.5 P or short 1.25 P) fade the
  groove over that length, its section moving out of the material as it turns (outward for a
  shaft, inward for a nut). ease_in is at the end the thread starts from. The runout lies past
  the full-form length: beyond a square stop, before a shoulder up to its clearance; at a free
  end inside the face. Runouts longer than the thread are refused. No end gets one by default,
  so saved threads keep their geometry.

The cut is the integral over the turn of the clipped section's 2π∫ r dA: engine test (2.5 P
and 1.25 P between two collars) within the sweep's wall tolerance times the runouts' wall area
(0.029 against a 0.036 mm³ bound), ladder 06/009 (004's shaft, a 2 P runout before the
shoulder) graded in closed form (measured 1.7e-6 off).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 7bfc184e8e A modelled thread's chamfered tip (ISO 4753)
`tip: chamfer` cuts ISO 4753's chamfered end at each free end a modelled external thread
reaches, after the groove, so the last teeth taper into the cone instead of ending in a
ragged first turn: the material outside a cone `chamfer_angle` to the axis (default 45°)
reaching d_f = d - 2 `chamfer_depth` at the face's end (default the external minor diameter,
the largest the standard allows), a revolved ring cut by one boolean per end. Past the end the
ring keeps to the radii the groove's overrun already cuts. An internal thread is refused (its
entry takes the hole's countersink), as is a tip with no free end or on a cosmetic thread.

The cone is axisymmetric and cut after the screw-symmetric groove, so the volume is the stock's
chamfered section with the thread's material fraction: engine test (both ends 45°, and 30°
x 0.5 mm at a shaft's one free end above a collar) within 1e-4, ladder 06/017 (measured
2.4e-7 off).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 3287bcba9e Threads with several starts
Ladder 06/008 had no way to ask for one: "solid.thread has no start count". `starts: n` (1 to
8) cuts n grooves of lead n x P, the j-th a j/n turn round from the first (the same helix j
pitches along), in one boolean with their union. A designation that gives the lead
(M16xPh3P1.5, Tr40x14(P7)) gives the starts, and a `starts` that disagrees is refused. The
helix's self-clearance check and the turn limit use the lead.

Over the same length n grooves of lead nP take the volume of one start of pitch P: engine test
(2 and 3 starts, M10xPh3P1.5) within 1e-4 of the closed form, ladder 06/008 graded as 001
(measured 3.5e-7 off).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:53 -04:00
jyvikoandClaude Opus 5.5 b4549d2700 Threads in the standard forms, right- or left-handed or both
Only the ISO metric 60° thread existed. Forms now (crates/doc/src/thread_forms.rs, values and
sources in docs/threads.md): ISO metric (ISO 68-1), trapezoidal (ISO 2904 design profile, ISO
2902 sizes), general purpose Acme (ASME B1.5), metric buttress 3°/30° (DIN 513), buttress inch
7°/45° (ASME B1.9 basic profile). Each has its groove as a straight-flanked polygon, its standard
sizes (none for ASME buttress), its designations (M10, M16xPh3P1.5, Tr40x14(P7), S20x4,
1/2-10 ACME, 2.5-8 BUTT) and the size that fits a face. The square thread is refused: no current
standard defines it.

`hand: right | left | both`: a left-handed groove is the screw motion about the reversed axis
rising along it; both cuts the two grooves, crossing, in one boolean. `steep_flank` turns a
buttress. The design diameters are checked against the published tables (ISO 2904/DIN 103,
DIN 513 via IS 4696-3); every form's cut against 2π∫ r w(r) dr per turn to 1e-4 in engine tests
and to 1e-4 in ladder 06/011 to 016 (they measure within 5e-7).

FeatureKind::Thread holds every option the command has (form, hand, starts, ease_in, ease_out,
tip, chamfer_angle, chamfer_depth, steep_flank, all defaulted so saved threads load unchanged);
starts, runouts and the chamfered tip are refused as not built yet. suggested_thread_in takes the
form.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-27 02:28:52 -04:00