Commit Graph
962 Commits
Author SHA1 Message Date
Homero Thompson 4ced1d7bcf Viewport: the grid fades with the distance instead of cutting off (#4214) (#4629)
* claim: #4214

* Viewport: the grid fades with the distance instead of cutting off (#4214)

The ground grid stopped at a fixed distance from the view, so its edge showed
as a cut across the picture. It now fades out with the distance from the
middle of the view, and it is gone before either of the two lines that used to
cut it: its own edge, and the picture's far plane.

Each grid line is drawn in pieces, and each piece is as faint as the fade
makes it at the distance where it lies. The 'under' batch is drawn by the
overlay pipeline with alpha blending, so the colour's alpha reaches the
frame.

* The headless grid fades with the distance too (#4214)

The headless path (solidcraft-cli snapshot, the home-page thumbnail, the MCP
screenshot) drew the grid from the engine's palette, where a line had no
alpha: the grid still ended in a cut, and at a low camera angle the cut was
in the picture.

A SceneLine now carries an alpha, the CPU rasterizer blends with it and the
GPU capture passes it on, so the engine's grid can fade. The fade itself
moves to the engine, next to the grid's other geometry, and both paths use
it: the headless grid now reaches as far on the ground as the view is wide
(the ground stretches as it is seen at a slant) and dissolves into the
distance instead of ending in a line.

* Fix the headless/viewport grid fade divergence (#4214)

The engine stretched the grid's size with the slant of the plane it is seen at, the viewport stretched it only on the ground, so on a sketch's plane the picture's grid reached further than the window's (153.42 mm against 120.00 mm). Both now share one grid_ext, which the picture and the window draw the same grid from.

* The grid fades out before the picture's far plane cuts the ground (#4214)

The window's grid faded against a far plane of its own: the scene's radius
clipped by the projection's camera (260 mm away at 400 mm of distance), while
the picture itself cuts the ground at the far plane of its own projection
(223.7 mm at the same distance, because the projection frames the scene's
bounds and not its radius). The grid was still a third of its strength where
the picture cut the ground, so the cut showed as a straight line across the
view.

The fade now ends at the far plane the picture's projection uses, and the
grid is gone before that plane cuts the ground.

The test that watched the fade now measures the ink of each row of the
picture, and checks that the grid is already gone in the ten rows above the
row where the far plane cuts the ground: the point it compared before lay
beyond that plane, where both renders draw nothing at all, so the comparison
was always true.
2026-10-26 07:59:56 +00:00
raykholo c8314687fc Construction points and axes: Browser rows, and pickable in the view and dialogs (#4312) (#4320) 2026-10-26 04:50:46 +00:00
raykholo 878339cac8 Sketch patterns: count, spacing, and angle follow parameters (#5231) (#5332) 2026-10-26 04:31:55 +00:00
bherbruckandClaude Opus 5.5 348bbc1dfa fix(joints): edge and corner picks follow the part when it changes (#6942)
The Joint dialog kept a round edge (a hole's rim), a straight edge and a
corner as plain points where they were picked. When the part got thicker,
a hole moved or the part got longer, the origin stayed where it was and
the jointed part overlapped the other one. An edit that left the picked
spot where it was (lengthening an arm away from the jointed hole) looked
fine, which hid it. Faces and hole walls were already found by name.

The dialog now sends a round edge as its circle's centre with its z, and a
straight edge or corner as an edge pick with its z. The engine keeps them
by name (the round end by its wall and the face across its rim, the edge
and corner by their edge and face names), with the frame the pick showed;
where it can't (no planar face beside the edge, no names), it keeps the
point as before. Edge origins get an optional axis (along the edge, or a
fixed direction) so a hinge on an edge keeps turning about it.

Tests: every joint type and as-built, for each way the dialog picks an
origin, with the arm made thicker, its hole moved and the arm lengthened,
inside one design and through Update Links.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-26 04:05:26 +00:00
262f5c61c0 Move, Align and previews on placed components (#4455)
* Move and Align on placed components: picks and vectors where they are shown

A body in a component placed away from its own frame (an imported part
set upright) moved the wrong way: Move's vector, axis and pivot were
taken in the root's frame, so moving the upright plate up moved it along
its own frame's z. They now turn with the frame of the bodies moved.

Align mapped each pick into the frame of the body under it, so aligning
two separately placed parts mixed two frames (the plate landed at right
angles), and its snap points were never mapped at all. Align now finds
its picks, face normals and snaps where the view shows them and takes
both ends into the moved bodies' frame.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Preview: a feature's tool is drawn where its component is shown

Extrude, revolve and the primitives preview their tool on its own. That
preview was built in the model's frame, so on a component placed away
from it (an imported part set upright, edited with its component
active) the tool showed at right angles to the picked face, though the
feature itself came out right.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Follow main's lazy body frames and first-part grounding in the placed-component work

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
2026-10-26 03:28:14 +00:00
816bcf10de Every new command comes with input and output schemas (#2829) (#4035)
* Every new command comes with input and output schemas

A test fails for a command without a contract or an output type, unless it is a planned!
placeholder or listed in schema/unconverted.txt, which holds the 400 commands that predate
the rule and only shrinks: the test also fails when a listed command has its schemas, when
the list names a command that doesn't exist, or when it isn't sorted.

`checked!` now takes only the command's id and checks the contract that id publishes
(`run_checked_as`), so the contract enforced is always the one described. Another test runs
every command that has a contract in strict with an unknown key, so a contract is never
published without `checked!`, under the command's own id, enforcing it.

A new book page, Command schemas, explains how to write a contract and a reply type, the
tests to add, the shared field types and how to add one, with a checklist; the failure
messages point to it. "Adding a command", CONTRIBUTING.md and AGENTS.md now include the
schemas, and the MCP tool description and docs/mcp.md no longer list the converted commands.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* List the commands added on main since: view.layout, view.history_layout, view.normal_to

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Command schemas guide: what participants and targets do, checking the evaluation, warning-free replies

- `participants` changes the result for some features and nothing for others; where it and
  another key override each other, or where it has no effect, say so in that key's
  description or in the summary.
- The example primitive's `targets` default to every body in the feature's component, not the
  bodies it meets; they're ignored when `participants` lists bodies.
- Check what each value does where the feature is evaluated, not only how the handler reads it.
- A reply test runs every form in Warn and checks for no `param_warnings` (Strict for a reply
  that isn't an object).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* List the 43 commands added on main since: frame, component, render and others

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* List the 11 commands added on main since: browser folding, standard views, parameter sweep, path flange

browser.collapse_all, browser.expand_all, inspect.parameter_sweep, sheet.path_flange and the
seven view.* standard views (back, bottom, front, isometric, left, right, top) landed on main
without schemas; the gate flags them, as intended. 457 commands listed.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Schema rule warns instead of failing for now

A command without input and output schemas prints a warning listing it
(test output and a CI annotation). SCHEMA_RULE_STRICT in coverage_tests.rs
(or SOLIDCRAFT_SCHEMA_RULE_STRICT=1) makes it fail again. Docs say "should,
and will become required".

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
2026-10-26 01:43:02 +00:00
leValdemar19andClaude Opus 5.5 b94692497e Sketch Dimension: arc length from an arc and its end point (#754) (#4245)
* claim: #754

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27

* Sketch Dimension: arc length from an arc and its end point (#754)

The arc-length dimension existed (sketch.dimension type arc_length) but
the Dimension tool could only give an arc its radius. An arc and one of
its own end points, in either order, now dimension the arc's length:
click the arc, then its end. The pair was refused before ("cannot
dimension that combination"), so no existing result changes. A point
where the arc's end is (a coincident line end) counts as that end.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 22:17:01 +00:00
ChrisNo a3890b3bd5 Open a linked part from its assembly Browser row (#2348) (#2349)
* claim: #2348

* Open linked designs from assembly browser

* claim: #2348

* Test linked design action with multiple components selected

* Fix linked design lookup in browser storage and translate its menu action

* Add Turn Up Axis to complete UI catalogs

* Keep browser DXF download after linked-design checks
2026-10-25 21:15:48 +00:00
59cad5f0bb Colored components (feature request #2507) (#2877)
* feat: add colored components inspection toggle

* feat: persist component colors and add cycling controls

* feat: assign component colors in creation order

* fix: update component color menu integration and translations

* fix: proper description for pending format change.

* fix: deleted duplicated format change description from docs/pending.

* Compare the component colour counter in the features-only check

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Vadim Kalinsky <vadim@kalinsky.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 21:11:03 +00:00
DuBearteandClaude Opus 5.5 0752d8d79c Extrude: a profile drawn twice is cut once, not as two coincident tools (#5543) (#5789)
* claim: #5543

* Extrude: a profile drawn twice is cut once, not as two coincident tools (#5543)

A circle drawn twice at one place is two profiles of one region. Extruded
together they were two coincident tools: a cut through a 121-hole grid with
four such circles retried the boolean with the tool nudged (four times) and
took 25 s instead of 0.5 s.

merge_regions, which every extrude, revolve and surface feature runs on the
regions it builds from, now leaves out a region whose boundary repeats an
earlier one (within 1e-7 of its size; corners and segment middles on the
other loop both ways, holes alike). The selection itself keeps its
multiplicities, as profile_refs' tests require.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 21:10:02 +00:00
raykholo 0344a41dc4 Open and insert a DXF outside a sketch (#2052) (#4635) 2026-10-25 21:03:31 +00:00
dba8108369 Timeline: a reorder evaluates the design once, from the cache it already has (#6186) (#6187)
* claim: #6186

* Timeline: a reorder evaluates the design once, from the cache it already has (#6186)

timeline.reorder checked the move on a copy of the model, then dropped it,
so setting the reordered design evaluated the moved part of the timeline
again; reorder_many (and moving features into a group) checked on an empty
model, recomputing the whole design even for a move near the end. The
check now starts from the session's own model, and the session keeps the
model it was checked on.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Marker is Copy: drop the clone

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
2026-10-25 20:55:52 +00:00
f512d4a004 Move: placements of one part moved together each go the way asked (#4768) (#4849)
* Move: placements of one part moved together each go the way asked (#4768)

A part placed more than once (an imported assembly's corners, screws or
fan blades) is one body in its component. Moving several of its
placements together moved that body once per placement listed, each
placement turning the move its own way, so the copies flew apart.

When solid.move names one part through two or more placements, it now
moves those placements in the world, as occurrence.move does with space
world: a placement held by a rigid group (an imported assembly) moves with
the outermost placement holding it, one inside another being moved isn't
moved again, and root-component bodies listed are moved as bodies, all in
one undo step. Other moves are unchanged, and so is a move with copy.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Free the grounded first part before the placement-move tests move it

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
2026-10-25 20:28:06 +00:00
NOWN-DEVandClaude Opus 5.5 826244bb28 Text parameters: a sketch text's words built from them follow every change (#727) (#6364)
* Test: a text's words follow its text parameters, and so does its cut

A sketch text whose words are an expression of text parameters (`Label + '-L'`): a parameter edit
and a configuration row that sets the parameter relabel the text, the text's cut follows, and the
expression is saved with the design.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc

* Text parameters: a sketch text's words built from them follow every change

A design's parameters are numbers; a text's words (a part label, a size code) could only be typed.
Text parameters hold words: `parameters.add` or `parameters.change` with `unit: "text"` (the
expression is the text, quotes optional), and `sketch.text` and `sketch.edit_text` take
`text_expression` (quoted texts and text parameters joined by `+`, `Label + '-L'`) instead of
`text`. The text is laid out anew from its expression on every evaluation, so a parameter edit,
a configuration row or a script relabels it and the features built on it (a cut, an emboss)
follow in the same rebuild. The design file keeps the text parameters and each text's expression
(one pending format change); a configuration table's parameter column can be a text parameter;
the Parameters dialog lists them under the unit `text`.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc

* Text parameters: the joints' same-but-features check compares the text parameters

The joints are solved once per change unless the design differs only in its features
(same_but_features, #6372), which names every Document field. The text parameters are a
field of their own and change what a text's words evaluate to, so two designs that differ
in them are not the same but for their features.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 20:24:23 +00:00
ab7602fd0e Project: don't lay a second copy over geometry the sketch already shows (#4929)
* Project: don't lay a second copy over geometry the sketch already shows

A sketch on a face already holds the face's border, linked. Projecting that face
again, or one of the border's edges, added a second set of curves and points over
the first: on a rounded corner that shows as extra points and lines. Project now
skips a reference whose curves are all linked into the sketch already (lines,
circles, arcs), reports it as `already_projected`, and refuses a pick of nothing
new so it adds no undo step. Points on their own (the origin, a vertex) still
project.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Projecting the face a sketch already shows adds no second copy in the face scenario

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
2026-10-25 20:13:46 +00:00
HiroKenEzandClaude Opus 5.5 b1d4293cf0 One set of X, Y and Z colours for the origin axes, view triad and Move gizmo (#976) (#4430)
* claim: #976

* One set of X, Y and Z colours for every axis (#976)

The origin axes, the navigation cube's triad, 3D sketch triads and joint
origins drew `axis_x/y/z` (255,0,0 / 0,255,0 / 2,2,248), the view triad and
the headless picture drew `triad` (220,60,60 / 60,170,60 / 60,100,230) and
the Move gizmo drew `gizmo` (225,70,60 / 80,190,80 / 70,130,240). The
`triad` and `gizmo` tokens are gone: every axis reads `axis_x/y/z`, now the
view triad's values (the engine's `view::colors::AXIS_*`, so headless
pictures are unchanged, and the set the red-green table was measured for).
Older theme files' `triad` and `gizmo` lists still read and set the axes.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 19:59:36 +00:00
99d5b43024 Doc: the names of split faces no longer grow with every split (#5860) (#6045)
* claim: #5860

* Doc: stop the names of split faces from growing with every split

* Joints: the long-piece-name test takes the longest name a piece now gets

Split-face names are bounded at 512 bytes since #5860, so the test cannot
build one over 512; it takes the longest the history gives.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 19:58:56 +00:00
3e6c039985 Fix/recovery metadata bounds (#5578)
* test: cover malformed and unbounded recovery metadata

Add regression tests for oversized JSON, mismatched entry IDs, and
non-regular recovery metadata. These expose failures in the baseline
recovery reader before the implementation fix.

Signed-off-by: Taha Zarif <tahazarif380@gmail.com>

* fix: bound recovery metadata reads and validate entry identity

Reject oversized and non-regular recovery metadata before reading it,
and bound the read if a file grows after inspection. Require each JSON
entry ID to match its filename for orphan listing and recovery loading,
preventing unrelated save paths from being attached to a recovered design.

Signed-off-by: Taha Zarif <tahazarif380@gmail.com>

* Format recovery.rs

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Signed-off-by: Taha Zarif <tahazarif380@gmail.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 18:49:55 +00:00
JK3D cbcf1fe716 component.list: group bodies, features and occurrences once (#6394) (#6395)
* claim: #6394

* perf: group bodies, features and occurrences once in component.list

component.list searched every body, every feature (three times) and every occurrence (twice)
for each component, so its cost grew with components times contents. Bodies, features,
occurrences and children are now grouped by component once, keeping their order, and each
component reads its own groups. The output is unchanged.

The new test lists nested components and checks each gets only its own bodies, features,
sketches, occurrences and children, in timeline order.
2026-10-25 18:42:06 +00:00
raykholo e21760e46d Sketch Move with a rotation swaps or drops horizontal and vertical constraints (#4645) (#4651) 2026-10-25 18:35:15 +00:00
raykholo df01e59716 Sketch: an x distance beside a y distance on the same points isn't refused (#4352) (#4387) 2026-10-25 18:27:40 +00:00
3045d0787e Dialog curve picks keep their sketch (#4057) (#4081)
* Dialog curve picks keep their sketch (#3726)

* Format

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Format

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Adapt context-menu test to Sel::SketchCurve's sketch field

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Path Flange picks keep their sketch too

Path Flange (#4096) landed after this PR and still looked its path up in the newest sketch with those ids.

---------

Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 18:20:03 +00:00
dudedagger42andClaude Opus 5.5 ceed604498 Mesh export: a quality choice, so small round features get enough sides (#4747) (#4773)
Every STL, OBJ and 3MF export meshed each body with a chord tolerance of
2e-4 of its size, with no way to ask for finer: a 3 mm hole in a 200 mm
part came out with about 14 sides. file.export and file.save_mesh take
`quality`: standard (as before, the default), fine (5e-5) or finest
(1e-5), and Save As Mesh has a Quality row, remembered like its format.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 17:42:51 +00:00
44bd29acc3 Hole: refuse a position that isn't on the face (#5024) (#5029)
* claim: #5024

* Hole: refuse a position that isn't on a face (#5024)

`solid.hole` took any `position` and drilled from the nearest face, so a
point 1 mm past a box's side was accepted and cut a hole across the edge.

A position given as a point (numbers or length expressions) must now lie on
a face of a body, within the same tolerance the plastic features use for
their placement (the check is shared with them). Holes at sketch points are
unchanged.

* Hole: a position over the mouth of a bore or opening of a planar face is on that face (#5024)

A counterbore is centred on an existing bore, in the plane of the face round it.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>

---------

Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-25 17:42:15 +00:00
HiroKenEzandClaude Opus 5.5 aa8e8cf69c Update Links: show which linked design it reads, off the window thread (#5329) (#5512)
* claim: #5329

* Update Links: show which linked design it reads, off the window thread (#5329)

Update Links read and rebuilt every linked design on the window thread, so the
window froze, with nothing on screen, until it finished. From the toolbar it now
runs as a file operation: off the window thread, with the overlay naming the
linked design being read (cover (2 of 3)), its rebuild step and progress, and
Cancel. The assembly stays as it was until the update is in, and it lands as one
undo step. The command reports each design through doc::progress::item.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 17:41:27 +00:00
raykholo c3dd40405d Measure: open surface bodies report no volume or mass (#4257) (#4268) 2026-10-25 17:21:39 +00:00
Ahmad Khan 0f90fb7e8d Edge flange: material outside and tangent bend positions (#5941) (#6060)
* claim: #5938

* Edge flange: height measured from the outer sharp, the inner sharp or the bend tangent (#5938)

An edge flange feature takes height_from (outer, inner or tangent) in sheet.flange and Height From in the Flange dialog, saved only when it is not the outer sharp. A height shorter than the bend takes is refused with the smallest height that fits.

* Edge flange: material outside and tangent bend positions (#5941)

An edge flange's position can now be material_outside (the inner virtual sharp on the edge) or tangent (the bend's outer face tangent to the edge's face), in sheet.flange and the Flange dialog. The bend starting at the edge was already the outside position, which now also answers to bend_outside.
2026-10-25 16:25:18 +00:00
amolinari-autotex 52e5bc114e Display cosmetic internal and external threads (#2367) (#2868)
* claim: #2367

* feat: distinguish cosmetic threads in shaded views

* test: keep cosmetic thread coverage compatible with current sections and assemblies
2026-10-25 14:53:24 +00:00
bherbruckandClaude Opus 5.5 093571cfe4 Connect AI apps at start-up, with a preference to turn it off (#6388)
At launch the app adds the solidcraft entry to each installed AI client off the window thread,
names newly connected clients once, and refreshes a stale path. Settings > Assistant has
"Make SolidCraft available to AI apps on this computer" (on by default); off removes the entries it
added. Entries the user changed are left alone; automation runs never touch the files.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 13:51:55 +00:00
a1b9ca13e3 Edit Feature: a primitive in a moved component keeps its placement (#2926) (#5989)
* claim: #2926

* Edit Feature: a primitive in a moved component keeps its placement (#2926)

Edit Feature passes a primitive's placement (corner, base, axis, center)
through as saved, in its component's frame, as timeline.inspect reports it.
timeline.redefine read it as a world point and mapped it through the
component's placement, so in a turned component the edit moved the
primitive: in the Hinge Assembly, Leaf B's rod flipped and the revolute
joint put the leaf on the other side.

A placement equal to the saved one now stays as saved; a new one is still
mapped from the world.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01TBKuBKHW3LfC7CMW1HYpwL

* Move the #2926 tests up in frames_tests.rs

They sat at the end of the file, where main has since added the #6000
test; moving them avoids the merge conflict.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: sascha2101 <221609842+sascha2101@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 13:00:40 +00:00
bherbruckandClaude Opus 5.5 dfde1e032d mcp setup: add SolidCraft to the AI clients on this computer; plain mcp finds a late app (#6379)
solidcraft-cli mcp setup (alias install) and Help > Connect AI assistants edit each installed
client's own configuration in place, with this program's absolute path: OpenCode, Claude Desktop,
Claude Code, Cursor, Codex, Gemini CLI, Copilot CLI, Windsurf, Zed and VS Code. Only the solidcraft
entries change; a stale path is refreshed and an entry the user changed is left alone.

Plain mcp keeps looking for the app while its headless session has no work, and says on every
tool result that it is headless when the app was not found.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 11:57:51 +00:00
Ahmad Khan 5a5a98ee80 Sheet metal: Path Flange, a chain of bends on an existing sheet edge (#4094) (#4096)
* claim: #4094

* Sheet metal: Path Flange, a chain of bends on an existing sheet edge (#4094)

Path Flange (`sheet.path_flange`): sketch an open chain of lines across a sheet edge, pick the
edge and one line; each line becomes a flange as long as the line and each corner a bend, one
feature and one body. The edge flange takes further bends (`then`), each on the far edge of the
one before, and the Flange dialog shows them as rows with a bin each.
2026-10-25 11:33:42 +00:00
Colin Faulkingham 0312808b92 DXF: reject non-BMP text instead of replacing it (#5056) (#5709)
* claim: #5056

* fix: reject unsupported Unicode in DXF text (#5056)

* fix: adapt new DXF callers to fallible writer (#5056)
2026-10-25 11:01:32 +00:00
Jesper We bbc3aa4301 Offset Plane: through a point (#3765)
* claim: Offset Plane through a point

* Offset Plane: through a point instead of at a distance
2026-10-25 06:02:14 +00:00
Jesper We 611d4eb6b8 Crash reports: a repeated panic that ends the app is counted, not reported as an unclean exit (#6051) (#6052)
* claim: #6051

* Crash reports: a repeated panic that ends the app is counted, not reported as an unclean exit (#6051)
2026-10-25 06:00:57 +00:00
Ahmad Khanandbegsaquib 919f54a23e Sheet metal: bend angles as the included (press-brake) angle, set per rule (#4968) (#6040)
* claim: #4968

* Sheet metal rules: bend angles as the included angle (#4968)

A sheet metal rule's angle_display (bend, the default, or included) sets
how the DXF bend notes read each bend: a 58° bend is B1 UP 122° R1 under
an included rule. The bend table always gives included_angle_deg beside
angle_deg (CSV and JSON). Set in sheet.manage_rules and the Sheet Metal
Rules dialog, listed by sheet.rules; the flange angle stays the bend angle.

* Bend table: the included angle as the CSV's last column, so the columns before it keep their places (#4968)

A test also covers a body whose base flange names its rule, which keeps that rule's notes whichever rule is active, and a bend down.

* Sheet Metal Rules: Angle Display reads Bend or Included, so the choice fits its box (#4968)

The rule editor's row contract lists the new row and the key the dialog sends.

---------

Co-authored-by: begsaquib <saquibbeg4444@gmail.com>
2026-10-25 05:11:13 +00:00
1d0e371e64 Preserve lid edge references after parameter changes (#5580) (#5658)
* claim: #5580

* fix: follow named lid edges after parameter changes (#5580)

* fix: initialize viewport test frame tints

* Drop duplicate tint fields in gpu view tests (main already has them)

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 05:04:24 +00:00
Matt Van Horn 43565cd33b Snap drawing to where two sketch curves cross (#4967) (#5342)
While drawing, the pointer snaps to the crossing of two lines, circles or
arcs and keeps the new point on both curves. Shift still prefers a midpoint.
2026-10-25 04:50:20 +00:00
rbousigues88andClaude Sonnet 5.5 157c0d68d0 Sketch Dimension: point/circle to circle or arc edge (#4064) (#4065)
* Sketch Dimension: point or circle to the edge of a circle or arc (#4064)

Adds PointCircleDistance and CircleCircleDistance (edge-based, like #1863):
solver, constructive seed, drawing, command wiring, tests, UI scenarios and docs.
Saved designs gain two constraint kinds, in one pending format file.

Fixes #4064.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>

* Sketch Dimension scenario: pick the circle at its top edge (#4064)

The bottom edge sits under the Dimension tool's status hint in the scenario window, so the second click never reached the tool.

Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
2026-10-25 04:29:28 +00:00
raykholo cc1e654690 Warn when a design is open elsewhere or changed on disk (#5467) (#5468)
* claim: #5467

* Warn when a design is open elsewhere or changed on disk (#5467)

The desktop app keeps a lock file next to each open design
(.~<file>.lock: computer, user, version, opened and refreshed times),
refreshes it every minute and removes it on close; a lock not
refreshed for three minutes is stale and ignored. Opening a design
that another SolidCraft has open asks: Open Read-Only, Open Anyway or
Cancel. A read-only design saves only to another file.

A design remembers its file's size and modification time when it is
opened or saved. Save over a file another program or computer changed
since asks: Save a Copy (the default), Overwrite or Cancel.

Programmatic calls never ask: doc.open reports open_elsewhere and takes
read_only, and file.save over a changed file returns an error until it
is given overwrite: true. ui.documents answers both questions.
2026-10-25 03:34:20 +00:00
raykholo 7af97e3729 Editing an Extrude or Revolve shows its sketch (#5336) (#5443)
* claim: #5336

* Editing an Extrude or Revolve shows its sketch (#5336)

A finished sketch is hidden once a feature uses it, and it stayed hidden
while that feature's dialog was open for editing, so no other profiles
could be picked. The session now holds the sketch of the feature being
edited; the edit dialog sets it while it is open and clears it however
it closes, and that sketch is drawn without changing stored visibility.
2026-10-25 03:26:36 +00:00
amolinari-autotex face5e2d31 Hole: independent tapping depth and recessed drill points (#4486)
* feat(hole): checkpoint independent tapped thread depth

* test(hole): cover independent tapped thread depth boundaries

* fix(doc): bind tapped depth to the useful cylindrical wall

* feat(hole): dimension independent thread depth in the section editor

* fix(hole): preserve custom tapping controls after main integration

* feat: add recessed-hole drill points and order depth dimensions

* fix(hole): match the current preferences and UI kit

* fix(hole): verify reference placement with independent tapping depth
2026-10-25 02:31:24 +00:00
rvmzym5xv8-starandClaude Opus 5.5 abc39685b1 Parameters: name the limit an out-of-range number or over-long expression broke (#5906)
Part of #4712.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 02:30:04 +00:00
Colin Faulkingham f93913b3d3 Sketch: accept curve snaps for Midpoint Line (#5981) (#6041)
* claim: #5981

* fix(sketch): resolve midpoint line snaps (#5981)
2026-10-25 02:29:47 +00:00
ivisafandClaude Opus 5.5 765c5fd143 Pictures drawn off the window thread finish before the process exits (#6062) (#6063)
A Home picture still being drawn by the detached saved-thumbnail thread
could be on the GPU as the process exited, and the process died with
SIGSEGV inside the graphics driver. capture::close stops new pictures
and waits for those in flight (the app calls it in on_exit), and
dropping SolveApp waits for the Home picture threads it started.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 02:29:40 +00:00
Colin Faulkingham 6494f8fe18 AutoConstrain: dimension construction geometry (#6173) (#6185)
* claim: #6173

* fix(sketch): dimension construction curves in AutoConstrain
2026-10-25 02:29:37 +00:00
selune 1623034973 Render: gate bundled studio-data tests in isolated engine builds (#5493) (#6202)
* claim: post-merge Render review corrections (#5493)

* fix(render): gate bundled studio tests in isolated engine builds (#5493)

Addresses jyviko review comments on #5494: compile the two positive payload-dependent regressions only with bundled-render-library. Keep all assertions and the explicit feature-absent refusals. Reproduced 5 pass / 2 fail before the fix; isolated default, CPU without pack, and CPU with pack tests plus strict scoped Clippy and repository checks pass. No production or CI configuration changes.
2026-10-25 02:29:34 +00:00
NOWN-DEVandClaude Opus 5.5 74004841b4 Sketch text: a text on a path follows the path in the same evaluation (#6215)
* Test: a text on a path follows the path when a parameter moves it

A construction line placed by a dimension that reads a parameter, and a text laid along it: after
the parameter changes the line has moved and the text has not. It follows one evaluation late.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc

* Sketch text: a text on a path follows the path in the same evaluation

Problem: texts are laid out with the sketch's links, before the sketch is solved. A solve that
moves the curve a text runs along (a path placed by a parameter) left the text where the path had
been before the change, so it followed one evaluation late.

Solution: after a solve that keeps the sketch's orientation, every text that runs along a curve
of its sketch is laid out again along that curve as the solve left it; a text that no longer lays
out adds its warning.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 02:29:31 +00:00
NOWN-DEVandClaude Opus 5.5 be08517de2 Construction: a plane on a sheet's flat face follows the face (#6217)
* Test: an offset plane on a sheet flange's face follows the flange

An offset plane on the inner face of an edge flange, picked by body and index as model.faces
lists it. When the base gets wider the flange moves along x and the plane stays where the face
was picked; a sketch on the same face follows it.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc

* Construction: a plane on a sheet's flat face follows the face

Problem: a construction plane on a flat face of a sheet body resolved the stored plane, which is
only where the face was when it was picked. When the sheet changed the plane stayed behind, while
a sketch on the same face follows it by its sheet face name.

Solution: a construction plane on a sheet's flat face resolves that face's plane as it is now, as a
sketch on the face does.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 02:29:28 +00:00
NOWN-DEVandClaude Opus 5.5 3592031d5e fix: joints on an imported part's hole or face stay on that part (#6368)
The parts of one STEP assembly import share their face names, and each
part's body stays where the file has it, placed in its component by an
offset. A joint origin on a named face (a hole's centre, a face's
centre, an x reference by face, the end a round origin takes) looked the
name up on every body of the design and compared the pick, in the
joint's component coordinates, with each body as it lies. Another part's
face of that name could lie nearer, and the joint resolved on that
part's face: a pin jointed into one plate's hole landed where the other
plate's hole is relative to its plate.

named_face now looks only at the bodies of the joint's component, each
in its own coordinates, a face the name finds exactly before a piece of
it or a face it was merged into, then the nearest. The design-wide
lookup stays for a face whose body has gone to another component.
named_round, x_axis, pin_end and end_faces take the component, as
face_name_at and round_end_at already do.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-25 02:29:16 +00:00