patch_continuity_and_points_cap_a_tube listed "g3" among the values surface.patch must refuse,
from #1521 when a patch built G0 to G2. Since cb8712aa0 Construction::Patch builds G0 to G4
(continuity_order.rs: `Construction::Patch => (G0, G4)`), so g3 is accepted, as it must be;
the order above what a patch builds is g5.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
raked_wedge (#1617, test from 7f2ae11a0 on 2026-10-17) rounds four end edges R4. Since
84bd2daad (2026-10-22) solid.fillet carries each picked edge round its tangent chain by
default, so the R4 now ran on round the end outline onto the R1.2 round's end arc, where the
round's rail on the end face would be an arc of radius 1.2 - 4 < 0, and it is refused as too
large. The issue's R4 rounds those four edges alone: the step says tangent_chain: false.
The test still fails, one step later, on SMLib: the issue's R0.854 round of both ends' outline
is refused by SMLib's own check (SmBSplineSurface Test #5, "close to singular at boundary"),
reported for the SMLib batch.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
tiny_cut_inside_exact_circle_survives_unfold_refold_and_dxf cut a 50 nm square 0.2 um inside
the disc's rim. SMLib models at a zone tolerance of 1e-4 mm: its check refuses the cut's 50 nm
walls as planes "degenerated to a point (tolerance=0.0001)", so the extrude was refused. A
feature below the kernel's resolution is not one it can keep, on any path.
The test's point is that the exact circle, not its display polyline, bounds the flat pattern:
a cut between the two must survive unfold, refold and the DXF. The polyline at 1e-3 has 224
chords (sagitta 10 (1 - cos(pi/224)) = 0.98 um), so the square is now 0.2 um across, centred
0.4 um inside the circle on the first chord's bisector: outside the polyline, inside the
circle, its walls and its 0.3 um gap to the rim above 0.1 um. Its hole's area is
(2e-4)^2 = 4e-8 (was 2.5e-9 for the 50 nm square).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Zebra, Draft, Curvature Map, Environment Map, Accessibility, Continuity,
Isocurve and Curvature Comb are one group: turning one on turns the one on
before off (Session::analyses_off), and the session says which is on
(Session::active_analysis). The new inspect.analysis names it and off: true
turns it off (typed contract and reply). The toolbar shows the active one's
button pressed, its tool running or not. Curvature Comb's button toggles:
on, the tool combs the edges clicked; again, off and the combs go; Esc or a
right click in the tool turns it off; opening another dialog leaves it on.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
inspect.curvature_comb keeps what it shows in the session (Session::comb):
add: true combs the new picks together with those shown, so every comb
shares one scale and tooth lengths compare across curves (a curvature jump
where two edges meet shows); with nothing picked it draws those shown again
with new options; clear: true ends it. Each sketch curve keeps its own
sketch. The tool runs it once per pick and per Comb length / Teeth change,
and the viewport draws the session's combs.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This replaces the spline fallback of 64efbe7f6. A face SMLib holds as a rational spline that is
an extruded circle was recognised as a cylinder over the spline's whole parameter range: for the
upper half of the peg's wall after the front top round that range runs 393 degrees round (u in
[-15, 40.18], SMLib's support surface extended past the face), and SMLib refuses a cylinder past
one turn. The face itself, its loops' box, spans u in [0, 8 pi]: half a turn. The cylinder now
takes the face's trimmed range, the least and greatest u and v of its uses' pcurves over their
edges' intervals, found to rounding on each Bezier span (the values at the pieces' ends bound the
extreme from below, the control points from above; pieces that cannot beat the best are dropped,
the others halved). A face whose trims run more than one turn round is no face of a cylinder: it
is refused as an invalid record, never kept as a spline.
The peg (40 x 16 x 10 bar, R8 end, a disc R8 extruded 10 up on its top, joined), front top edge
rounded r2: the body measures to 1e-7 of its closed form, the three r2 corner rounds after it
build and measure, and the upper wall comes back from SMLib a cylinder of radius 8 (engine test).
The rig case of the round of the edge where that round meets the wall (tangent at one end) still
fails, for another reason: on the wall as its exact cylinder SMLib refuses the round as larger
than the faces beside its edges allow (it fades to nothing at the tangent end) instead of
returning a body its own check refuses. Its KNOWN_FAILING line says so.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A curvature-continuous fillet (type curvature, equivalent radius 2) of the three edges at a top
corner of the owner's bar built, but its corner was SMLib's own patch, which is only tangent to
the rounds: Continuity Analysis measures a 35.8 / mm curvature jump across its seams (with the
rounds G2 to the faces everywhere else), and it shows as a dome sitting on the corner, the
vertical round's shading lost under it. All three edges were rounded; the corner was not
curvature-continuous, and nothing said so.
Such a corner, where three or more rounded edges meet, is now set back (1.5 r unless a setback
names it) and left open by SMLib with the curvature sections (smlib_blend_setback_open with
SMLIB_BLEND_CURVATURE), and filled with the G2 patch fillet_g2_corners already uses for circular
rounds (fillet_g2_with_g2_corners). The `corner` option no longer leaves a curvature fillet with
SMLib's patch: its corners are always G2, and setbacks on it set back the curvature rounds (they
were circular rounds before). Where SMLib or the patch cannot build it, it is refused.
On the reported geometry every seam of the rounds and the patch is G2 (rig
report-fillet-curvature-three-edges-at-bar-corner-solver-residues), and the rounds outside the
setback cube measure exactly: V0 - 27 - (the quintic section, A2 = 0.597884, along the front edge
from 3 to the wall and along 7 and 13) = 9541.116961 (...-outside-setback). With round coordinates
SMLib's open sheet fails its own check (a 2D curve cusp, SmBSplineCurve test 13): the fillet is
refused, listed as known failing (report-fillet-curvature-three-edges-at-bar-corner).
Test: corner_g2_tests::curvature_rounds_meet_at_a_g2_corner (box corner, r5: the patch's jump
under CURVATURE_SHARE / r clear of the hole's corners, SMLib's own patch over ten times that).
Changes a default: a saved curvature fillet with such a corner rebuilds with the G2 patch; there
is no preference or fallback to SMLib's patch.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A 220 x 11 two-distance chamfer of a tapered plate's bottom front edge (rig fillets/5181) runs up
the front face past its straight side edges, l2|start and l6|start, and takes them up: no result
edge comes from them. SMLib leaves the blend face untagged, and it was given every blended edge
whose two faces lie next to it: the picked edge l1|start and both taken-up side edges. Its name
came from the first in edge order, F3:blend:F2:side:l6|F2:start, an edge the user never picked.
A blend face now comes from the picked edges it lies between; only a face that lies between no
picked edge's faces (a corner's piece over a short edge the corner took up) comes from the
taken-up edges it lies between. The chamfer is F3:blend:F2:side:l1|F2:start everywhere on it.
Persistent names: a blend face that also lay between the faces of an edge the blend ran over is
now named by its picked edge only. There is no alias for the old name (5181's
F3:blend:F2:side:l6|F2:start): a saved reference to it is reported lost.
Also corrects 5181's "what": the chamfer builds (335399.749), it is not refused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The edge where a round runs into a cylinder's wall it is tangent to at one end (the bar's front
top round meeting the wall at (40, 0, 8), where the round's contact with the front face meets the
wall's tangent line with it) was refused as smooth, "nothing to round": the faces' normals were
compared at the edge's start alone, which was that tangent end. They are now compared at five
stations from end to end, and an edge is smooth only where its faces meet tangentially at every
one: this edge is a crease everywhere but its end. The wall's seam with the front face, tangent
all along, is still refused as smooth.
The round of that edge with its tangent chain (the top's concave arc) now reaches SMLib, whose
result fails its own check (internal poles, coincident control points, cusps where the round
fades out): its rig case in fillets is listed as known failing for that SMLib defect.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A round of a bar's top edge, where the bar's side runs tangent into a cylinder standing on its
round end, seemed to build: SMLib's result holds the cylinder's wall as a rational spline whose
parameter range runs 393° round (u in [-15, 40.18]). Going back into SMLib (to measure the body
or change it again) the record's extruded circles become SMLib cylinders with the face's range on
them, and that range was 6.866 rad: SMLib refuses a cylinder past one turn
(SM_ERR_INVALID_INPUT from BrepFromFlat's face range check). The body could not be measured, a
second round on it failed, and the app said one of its freeform faces can't be used. An extruded
circle whose range runs more than one turn round now stays the exact spline it is.
The bar of the reported design (40 x 16 x 10 with a R8 end, a disc R8 sketched on its top and
extruded 10 up, joined): the front top round removes the spandrel up to the cylinder's wall,
integral over y in [0, 2] of (2 - sqrt(4 - (2 - y)^2)) (40 - sqrt(64 - (8 - y)^2)) = 32.306475;
the three rounds at the other top corner after it remove 53.285832 in all (spandrels outside the
corner cube, the cube less the rolling ball's eighth). Both now build and measure to 1e-7; the
curvature corner of the three edges at once (setback 3) builds too.
Rig cases (fillets) for the three reports: the curvature corner of the three edges, the front
top round, and the three corner rounds after it pass; the same corner rounds with the design's
~1e-10 mm sketch residues fail in SMLib (its corner's surface of revolution is close to singular
at its boundary) and are listed as known failing. (Their ids take the report- convention in the
rig commit later on this branch.)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The shell unit tests that checked geometry become shell rig cases built through
commands: the trough and the pocket whose floors fall 1 deg to a central drain
(the pyramid made as two triangular prisms intersected, in place of
convex_polyhedron; the cavity integrated exactly over the cells where each moved
facet is highest, sharp inner corners as the ladder's tier 09), the box opened at
a bottom rounded R2 and R2.4 (refused: the rim would have no thickness) and R1.5
(built, exact volume), and the plate with a hole through its arc side. Four
action-matrix shells that regressed (issue-616's lid, the ring-cut frame, the
filleted shelled box shelled again, the up-down join) get small cases too. The
ones that fail today are on KNOWN_FAILING with their cause, and the unit tests are
removed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The fillet and chamfer unit tests that checked geometry become fillets rig cases,
built through commands with answers derived by hand (each method field gives the
derivation): a plate outline and a disc rim as tall as or past their wall, a
notched block's outline at R7 and R8, a cube corner as wide as its faces (refused,
and reduced), the 1668 wall at R7 alone and both sides, the 2852 U shell at R30
(refused, naming 25.24), the 851 knife edge (R2, chamfers 0.5/2/5 on three
constructions), the arc top edge at the full wall height and at 9.5, the 851
table of selections, the 556 top edge ending on the boss wall, the 2893
cylinder-rim chamfer refusals and the elliptical rim, seed 33's full round, the
sloped basin rim blends (single edges with exact volumes, loops with the slab's
box), and three action-matrix chamfers and fillets. fillets/851's three-edge
corner gets its volume (67.051 removed, re-derived on a grid; the engine test had
67.05). Chamfers whose leg runs off the face beside the edge are refused and rounds
past a face on its tangent side build, as the owner ruled on 2026-10-30. The cases
that fail today are on KNOWN_FAILING with their cause.
The unit tests are removed, except two cut to what no command can express: the
per-edge-radius refusal at a cube corner and the chamfer of a cylinder's seam.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A colliding pair past the 16 pairs whose volumes are worked out, or past
the check's 256 body intersections, or whose intersection could not be
made, fell back to the sampled mesh depth for its deepest step. That
changed what deepest_step means without saying so. Such a collision now
answers deepest_step and volume_mm3 null and not_measured naming the
budget it ran past (or the intersection that failed), as compare does
since #9132; first_step, last_step and steps are exact and stay.
B pushed through A at 1000 samples overlaps it at about 330 samples, past
the 256 intersections: not measured, "the check's 256 body intersections
ran out". At the study's 16 samples it is measured, deepest at step 15.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
motion.interference picked a collision's deepest step by the depth sampled
on the contact meshes (vertices, edge midpoints, triangle centres), and
worked out the exact shared volume only there. That depth depends on where
the mesh puts its points: since planes mesh as their boundary's triangles,
the arm turning into a block (rig case
assemblies/cov-motion-interference-arm-into-the-block) sampled 4.64 mm at 60
degrees and 2.0 mm at 90, and the check answered step 6 with 536 mm3. The
exact depth is 5 mm at every step from 60 to 90 degrees (both slabs are
10 mm thick), so depth cannot tell those steps apart.
The exact shared volume is now worked out at each sample a pair overlaps,
and the deepest step is the first with the most (a tie keeps the earlier
sample). The arm and block share 536, 807, 952 and 1000 mm3 at 60 to 90
degrees, so it is step 9 with 1000 mm3, at 10 samples or 19. depth_mm is
reported as before and documented as an estimate from the contact meshes.
volume_mm3 is null, and the step falls back to the sampled depth, when the
volume was not worked out at every sample (more than 16 pairs, or past the
boolean budget, raised from 64 to 256 now that it covers every sample).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
`inspect.curvature_comb` read the display mesh for model geometry: an
edge's comb fitted a circle through every three points of the nearest
mesh polyline, a face's did the same on its iso lines' chord points. The
comb was jagged, changed with the mesh tolerance and ignored `density`.
- geom: `CurveEval::jet`, a curve's point, unit tangent and curvature
vector kN from its first two derivatives (lines and conics in closed
form, B-splines and NURBS from the basis functions' derivatives, a
traced intersection from both surfaces' normal curvatures along its
tangent, by Meusnier: kN lies in the plane of the two normals and its
component along each is that surface's normal curvature).
- kernel (curvature_comb.rs): the edge nearest a pick by the exact
distance to its curve (a periodic face's seam and poles left out),
`density` teeth at even steps of the edge's parameter; along an iso
line, the surface's normal curvature n.S_tt / |S_t|^2 along its normal.
`IsoLine` carries the running surface parameter's span.
- engine: edges and faces use them (and `inspect.minimum_radius` on
edges); new optional `length` multiplies the automatic scale. The reply
keeps its shape.
Tests: a circle edge reads 1/R to 1e-9 at Coarse and Ultra display
quality alike, with `density` teeth; an extruded ellipse's edge matches
ab/(b^2 cos^2 t + a^2 sin^2 t)^(3/2) at every tooth, a/b^2 and b/a^2 at
the vertices; a cylinder face's rings read 1/R and its lines 0; `scale`
and `length` set the teeth's length; curve jets on every record kind.
The existing cylinder-edge check tightens from 0.5 mm to 1e-9.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ordinary_curved_bodies_keep_a_practical_sampling_step asserted
ContactGeometry.step > 1.0, an internal sampling step derived from the
bodies' display meshes. What a user gets is the drive: it either stops at the
contact or is refused for running out of the sampling budget. The test,
renamed ordinary_curved_bodies_stop_at_their_contact_within_the_sampling_budget,
keeps that: the slide drives to -30 without a budget error and stops in
(-5.02, -4.9) (the sphere r 5 about x = 20 and the box from x = 15 meet the
block's x = 10 side after 5).
It still fails on develop with "motion exceeds contact sweep collision
budget": the planar faces meshed as grids, which the planar-tessellation fix
(#9307) addresses.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
open_in_easyprint_hands_the_host_a_3mf_or_an_stl_that_reads_back asserted the
STL was 84 + 50 * 12 bytes: twelve triangles, the tessellator's count for the
fixture's box (the fixture is a mesh import of box_solid's display mesh, 124
triangles today).
The STL is now parsed (solidcraft_io::read_stl): it has the imported mesh's
own triangle count, every side is shared by two triangles running opposite
ways (closed and consistently wound), it encloses the 10 x 20 x 30 box's
6000 mm^3 (divergence theorem, to 1e-6; the corners are exact in f32) and its
bounds are (0, 0, 0)..(10, 20, 30).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
free_form_profiles_extrude_exactly asked for an ellipse extrusion of exactly
3 faces and a spline-and-line extrusion of at most 5: how many pieces the
kernel cuts a closed side into. It now checks that the sides are exact.
Ellipse a = 10, b = 4, extruded 5: area = 2 pi a b + 5 P, P = 4a E(e),
e^2 = 1 - b^2/a^2. By the Gauss-Kummer series, P = pi (a + b) sum_k
(binom(1/2, k))^2 h^k, h = ((a - b)/(a + b))^2 = 9/49: P = 46.026225191330
(a 200000-point midpoint integral of sqrt(a^2 sin^2 + b^2 cos^2) agrees to
1e-13). A = 80 pi + 230.131126 = 481.458538 mm^2, asserted to 1e-4; a faceted
side would be short of it. Only the top and bottom are planes
(face_types.plane = 2, merged pieces counted once).
The fit spline closed by a line: the planes are its top, bottom and the line's
side (face_types.plane = 3); its volume stays checked against the profile
area.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
a_mirrored_or_patterned_sheet_body_is_sheet_metal_with_its_flat_pattern
(1171c4c2a) expected the mirrored copy's model turned over: the same outline,
its bend down and its pocket on top. That describes a SheetBody::moved that
never landed. The code on develop is SheetBody::copied (d9d6af51c, #3354): a
mirror moves the frame and mirrors the flat x -> -x with the same thickness
side, the opposite hand's blank with each bend turning the same way, which
a_mirrored_sheet_copy_is_the_opposite_hand_with_the_mirror_image_flat_pattern
asserts on an asymmetric bracket. The YZ mirror keeps z, so a pocket cut from
below stays below and the flange on y = 0 still turns up: the flat pattern
reads blank x 0..100 -> -100..0, pocket x 20..30 -> -30..-20, side bottom,
bend up.
The test now asserts that: the same flat size, the outline and the pocket
outline equal to the source's with x negated (to 1e-6), pocket side bottom and
bend up on both. The volume doubling, the bend table and the flange rebuilt
on the copy (point containment) stay.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
a_trays_faces_have_readable_sheet_names_that_follow_its_size asked for
exactly two unnamed faces (the hole's wall in two halves) and for the back
rim's named point at y = 199.5, the strip's centre line. The first is how many
faces the kernel makes a cylinder of; the second is where the face's roomiest
display triangle lies (naming::face_spot), any point on the face.
Now: there is an unnamed face and every one is the hole's wall (r 3.3), and
the back flange's far rim point lies on that rim: z = 30 and 199 <= y <= 200
(the flange 1 thick, its outside at y = 200), 0 <= x <= 400, to the 1e-3 the
test had. The right flange's top (the plane x = w - 1) keeps x = 319 and 399.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillet_the_knife_edge_at_the_tip (features_more_tests.rs) and
blend_a_knife_edge_where_a_curved_wall_runs_out (tests/robustness.rs) build
the same #851 part with the same script, round the same knife edge at
(62 1/6, 0, 5) with R2 and measure the removed volume through the same display
plan. The first integrated the removed area on a grid (5e-4); the second has
it in closed form. Drop the first and keep its tolerance on the second.
The ball 2 from the back face y = 0 and from the r 21 wall about (62 1/6, -21)
is centred at (62 1/6 - sqrt(168), -2). The removed section is the trapezoid
wall centre, tip, (kx, 0), ball centre (sqrt(168) wide, 21 and 2 high) less the
wall's sector theta = acos(19/23) and the ball's sector pi - theta:
10 (11.5 sqrt(168) - 220.5 theta - 2 (pi - theta)) = 119.648812 mm^3
the constant the kept test has; the dropped test's grid gives 119.6487 at a
0.004 x 0.001 step. The kept test's fillet bound goes from 0.5 to 5e-4 of
that (0.0598), the dropped test's. Its chamfer row (159.236451, the chord
triangle less the wall's segment) already says the chamfer takes more.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
cut_whose_end_touches_an_arc_side_leaves_no_sliver compared the touching cut's
face count with a clear cut's, a count of how the kernel splits its faces. It
now compares what the two parts are.
The plate's arc runs from (0, 20) through (-10, 10) to (0, 0): centre (0, 10),
r 10, so it reaches x = -10 only at y = 10. The r 5 cut along x about
(y, z) = (12.5, 12.5) spans x -10..7.5 (touching) or -10.1..7.4 (clear). Both
open the same patch of the arc; the slice x 7.4..7.5 lies wholly inside the
plate (y 7.5..17.5, z 7.5..17.5 in 0..20 x 0..27.5). So
V(clear) - V(touching) = pi 5^2 0.1 = 7.853982 mm^3
A(touching) - A(clear) = 2 pi 5 0.1 = 3.141593 mm^2 (the hole wall; the
floor disc is the same)
both to 1e-4 (the measure integrates the exact faces to 1e-8). A sliver of the
arc left where the end touches adds about a square millimetre of faces.
Seed 14's half (the fuzz generator's seed, then a shell) is pinned as its own
test, shell_after_a_cut_whose_end_touches_an_arc_side, with the commands the
generator gives today: the touching cut, then a 2 mm shell opening the top
face y = 20. It fails at the shell (SMLib status 1001), a kernel gap.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Stale since 84bd2daad, which gave solid.fillet each pick's tangent chain by default. After the
long top front edge is rounded, the front-left upright meets the round's end (the quarter circle
on the left face) along its tangent, and that circle meets the top-left edge along its tangent:
the second fillet rounds the upright and the top-left edge. The "together" fillet picks the
three edges ([20, -21, 10], [0, -21, 5], [0, -10, 10]); one by one and together remove the same
volume within the display meshes' 2e-4 (it read 60.649 vs 43.185 with two picks).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The test offset the sphere's top patch to get a fitted B-spline sheet. That held on truck,
whose sphere came in several patches and whose sphere offset was fitted. On SMLib the
sphere is one face: offsetting it closes up, so it is a solid by design (surface_offset.rs,
"Faces that close up make a solid", and its test a_sphere_is_fitted_and_refused_past_its_centre
asserts exactly that), and SMLib's offset is exact, a sphere of radius 22 with no control
points, which surface.fair refuses. Body::is_surface was right: the record lists the offset's
closed shell as the outer shell of a material region (Parts::canonical), so it is a solid
whether read from edge uses or from regions.
The test now fairs the patch on the non-planar rim of a box cut by a sideways cylinder (the
cover in patch_trim_thicken_and_stitch), a one-face B-spline sheet: energy 0.7185 → 0.6938 in one
step, edges unmoved bit for bit, undo/redo/reopen and the refusals as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
hostile_params_never_panic built a box, a sketch and a rectangle afresh for each of the ~3000
calls it makes per command. SMLib serialises every call behind one process-wide lock, so those
boxes were built one after another whatever the number of threads: 20 threads made 4000 boxes
in 7.8 s, one thread 200 in 0.31 s (1.5 ms each). The fixture was nearly all of the test's time
(8814 of 8823 thread-seconds over the first 72 commands on the aarch64 box; the commands
themselves 9 s, none over 0.5 s), and the test took 2195 s in develop CI.
It now builds that model once per command and gives each call a copy of the session with its
design, model, undo, redo, open sketch and log, sharing the bodies as undo does. Every command
still gets every parameter name with every hostile value, from the same starting state. A new
check runs Cancel Sketch, two undos and a redo on a copy and on a session built afresh and
finds the same designs, with the copied session untouched.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The refusal "capture the source occurrence position before generating a
legacy face profile across components" lost its test when Offset Face got
an exact history name (b6c3bf3c5). A half of a box's top that Split Face
divided still has neither a construction certificate nor an exact history
name, so Extrude from that face, in a component whose occurrence has an
uncaptured move, takes the legacy path and is refused there; the document
and the pending moves stay as they were.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The kernel switch broke these tests only through their counts, which record how a kernel splits
faces rather than whether the result is right. Each now checks its intent:
- a fitted circle is the exact circle (centre, radius, a full turn), not "one segment";
- the tight bend sweeps a valid solid of Pappus' volume, πr²(40 + 5π/2), not a count of faces,
edges and vertices;
- the Pi case keeps each outer side one face, stays valid after every feature and rebuilds the
same topology at 32 whether built there or edited there, without a hard-coded table of totals;
- a certified paint stays on the wall's radius and covers as many faces after an edit, a copy
and reopening as when it was painted;
- the offset sleeve and the extended strip are checked by their exact areas only.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillets_on_tapered_bosses_saved_before_still_find_their_edges compared the part with
69454.885209 mm³, what the truck build that saved it measured. In closed form: the 80 × 40 × 20
block (64000); the 20 × 20 boss 10 high tapered 5° in, a frustum to a 20 − 20 tan 5° square
(3660.251034); the Ø16 boss tapered alike, a cone frustum to radius 8 − 10 tan 5° (1798.751833);
less the R1 round on a sloping corner, the corner's section r²(cot φ/2 − (π − φ)/2) at its
dihedral angle φ = 90.435° times its length between z = 20 and 30 (2.124401), and the R0.5
round all round the cone's top, the section at the rim's 95° turned about the axis by Pappus
(1.928463): 69454.950004. SMLib's part measures 69454.950004.
The test still fails before that check: Fillet2's saved edge `F4:side:c1#1|F4:top#[F4:side:c1]`
names a half of the cone wall truck built, which SMLib builds whole, so it is found with a
"was split" warning (a persistent-name question, see the PR).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since 0a216d692 tangent and curvature extensions are SMLib's G1 and G2 extension of the surface
(smlib_extend_sheet, CreateExtendedSurface), and the face stays one face on it, as
surface_extend's docs say; extend_a_cylinder_strip_every_way still counted truck's separate
run-off face (2). It counts 1.
The test still fails after this, on the curvature run-off's area (see the PR): SMLib's G2
extension of the quarter cylinder by 5 gives 413.882 (a section 4.986 long), where the test
works out the parabola's 418.182.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
cut_keeps_posts_joined_while_apart_in_one_body expected the reply's `bodies` as
["Case", "Case (1)"]. That list is the state's order, which is SMLib's lump order (the -x half
first); the names follow the pieces' faces (lineage::order_lumps, 08cf526fe): the piece whose
least face name sorts first keeps "Case". That is the +x half, whose least is `F1:+x`, before the
-x half's least, its piece of `F1:+y`. The test now checks the names as a set, that the +x half
(from x = 1) is "Case" and the -x half (from x = -30) "Case (1)", and each half's volume as
before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since 09c979a4b a circle is one closed arc, so an extruded circle's wall, a hole's wall and a
cylinder's side are one face each, closed along a seam. Tests that counted truck's two halves:
- certified_annulus_side_rows_follow_radius_edits_and_clone and
certified_side_transfer_preserves_geometry_and_unsupported_taper_refuses_atomically: the
painted outer wall is 1 face (every vertex of it still at the painted radius), not 2;
- offset_surface_of_a_cylinder_and_a_box_top: the offset sleeve is 1 face (its area 2π·12·20
unchanged);
- press_pull_then_curved_face_offsets_it: a click on the hole's wall offsets its 1 face;
- pi_case_faces_per_step_at_both_heights: each standoff (a ring, Ø6 round a Ø2.5 hole) adds 4
faces, not 6: its outer and inner wall, its top, the floor inside its hole. So 23 after the
first and 35 after the pattern of four; the port openings (3 × 4), the end cut-out (4) and the
five vents (5 × 4) are planar and add what they did: 47, 51, 55, 71.
- the_round_sides_of_a_thin_ring_are_named_by_the_circle_they_run_beside: a thin ring 2 thick
about the R10 circle has two walls, `F2:wall:c1:left` (radius 9: the counter-clockwise
circle's left is inside) and `F2:wall:c1:right` (radius 11), with no numbers; each name is
found again by a point on its own wall.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Two expectations encoded truck-era output:
- a_flange_bent_inside_keeps_the_base_sketchs_arcs_in_the_flat_pattern_and_the_dxf: the
DXF has 7 LINEs, 4 ARCs, 11 shapes (was 9, 4, 13). The flat outline is SMLib's exact 2D
union of the plate, the bend zone and the flange panel; a zone's side and its panel's side
meet in line, and a region's boundary has no vertex in the middle of a straight run, so
each flange side is one line: 6 outline lines (plate top, left, right; flange sides and
end) and the bend's centre line. The same reason as 5d25684a1 gave for
a_base_trimmed_for_a_flange_keeps_its_arcs (12 to 10 edges). Areas, the bend length and
the volumes are checked as before and hold.
- hole_beside_two_adjacent_edge_flanges_cuts_and_bends_stay_guarded: the folded volume was
14057.2 +- 0.1, a faceted measure; since 32ae0cd9c the measure is SMLib's exact integral,
14057.3837123. Exactly, a folded sheet holds its flat area A times t, less each bend's flat
strip L·t·(R + K·t)·π/2, plus its sector L·t·(R + t/2)·π/2: t·A + t²·(½ − K)·(π/2)·L. With
t = R = 2.5, K = 0.44, A = 5597.0353454 (the flat pattern) and L = 75 + 35, that is
13992.5883635 + 64.7953485 = 14057.3837120, within 2e-11 relative of the measure. The
test now checks that identity to 1e-9.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fixed_seeds_run_clean expected the join of a box touching the first only along
an edge to be refused with "zero-thickness edge contact". Since 94ee28d5c (doc:
a join keeps solids that only touch as separate bodies) such a join succeeds and
keeps the new box a body of its own with an along_edge notice, which
join_touching_along_an_edge_keeps_a_separate_body asserts in engine tests.rs.
The seed now expects that: the notice, two bodies, each valid, and the volumes
unmoved, 25 x 15 x 10 + 17.5 x 17.5 x 20 = 3750 + 6125 mm^3.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Under the blend-overflow decision (237f0ae74) a convex round running over a face's far
edge (a cliff) is built and cut from the part, so the truck-era fixtures of the reduce
and taper fits (a 2 mm fin, a plate narrowing to 2 mm, a wedge, a 10 mm cube's edge at
R20) no longer refuse their radius and the fits have nothing to react to. Each test now
uses a case SMLib still refuses, and checks the cliff case builds:
- engine fillet_fit_reduce_keeps_the_radius_where_it_fits: a 14 x 6 x 10 post on a
40 x 30 x 20 block, its four verticals at 3.5 (two rounds would cross on its 6 mm ends)
reduced to 3 on 4 of 5 edges, the block's corner kept at 3.5: 24840 - (4 - pi) 90 -
(1 - pi/4) 3.5^2 20. New fillet_fit_reduce_keeps_a_round_over_a_cliff: the fin's R4
builds, nothing reduced, at the kernel's fillet_max_each answer.
- engine fillet_fit_taper_follows_the_room_along_the_edge, spline_fillet_takes_over_a_taper,
kernel taper_follows_the_room_along_the_edge, ui-egui fillet_spline_handle_tests: the
narrowing plate stands against a wall behind its slanted side (z -15 to 30), so its top
and bottom end in concave edges: R3 is refused and tapers 3 -> 1.8 as before. Without
the wall, R3 is cut over the 2 mm top's far edge and kept constant: at x the section
loses (1 - pi/4) 9, or 3 w - (F(3) - F(3 - w)) where the top is w < 3 wide, 6522.7745566.
- The wedge closing to a point: on its own R16 is cut over its cliffs (the section
integral, 4195.578821, SMLib within 4e-8) and kept; its room's taper is checked as a
spline fillet. Against a wall (new fillet_fit_taper_closes_to_a_point) the taper must
close to 0, which SMLib fails today (status 1001).
- kernel taper_mesh_tests: the collapsed taper is built from taper() as a spline fillet.
- ui-egui the_feature_menu_copies_a_warning_message: the 10 mm cube's four verticals at
6 are reduced to 5 (a full round), which the warning says.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's blend-overflow decision (2026-10-25, 237f0ae74): a convex round or chamfer
whose rail runs off its face across a cliff (an opening's rim, a hole, the part's
outline) is built on the faces continued and what it removes is subtracted, so it never
bridges an opening; a round may use up a face; a chamfer of a face's full width stays
refused. These tests still expected truck's refusals. Each now expects the decision's
body, with its answer from the geometry:
- issue_1080 chamfer_into_a_pocket_is_cut_by_it (was ..._is_refused_with_the_size_that_fits):
chamfer 6 into the pocket 4 mm in removes 360 - 20 (its triangle less the part over
the pocket): 14660; 6 along the top and 2 down, 120 - 20/3; 2 and 6, 120.
- issue_1080 fillet_into_a_pocket_is_cut_by_it_and_one_that_fits_builds: R5 removes
(1 - pi/4) 25 along 20 less 10 (5 - (sqrt(24)/2 + 12.5 asin(1/5))): 14893.0344442.
- issue_1080 chamfers_crossing_each_other_are_refused: still refused (they cross);
chamfer_max and fillet_max find 2 mm.
- issue_1080 rounds_on_both_sides_of_a_wall_build_as_one_fillet: R7 alone opens a slit
where its arc passes the inside corner: V0 - (104 (1 - pi/4) 49 - 100 a), a = the square
[25, 30] x [35, 40] outside the circle about (25, 35), 5 (5 - sqrt 24) - (F(5) - F(sqrt 24)):
38458.8958265. Both at R7: the arcs about (25, 35) and (23, 33) cross only outside both
quarter arcs and the inner round's material holds the slit, so V0 - 4 (1 - pi/4) 49 =
39509.9380404 (was expected refused).
- issue_324 a_round_into_a_hole_is_cut_by_it (was the_radius_offered_beside_a_hole_fits):
R4 over the r3 hole: 8000 - 90 pi - (640 (1 - pi/4) - the round's height over the
hole's width, integrated with y = 17.5 - s^2): 7580.2873154.
- issue_851 arc_top_blend_uses_up_the_wall_and_refuses_a_collapsed_one: a round of the
wall's full height uses the wall up (one face for the wall, the removal integrated as for
the other sizes); the full-height chamfer stays refused.
- kernel tests: fillet_max_finds_the_largest_radius_that_works keeps the post (3.5 -> 3)
and the no-edge case; its disc and notch cases move to
rounds_past_the_bottom_of_a_wall_are_cut_from_the_part: the 2 mm disc's R2.5 turned
section, pi (338 - integral of (169 - rho^2) dz), rho = 10.5 + 2.5 cos(theta) (the same
formula gives SMLib's R2 994.15188 exactly), 957.6922389; the notched block's outline
R7, 11925 - (1 - pi/4) r^2 (140 - 8 c), c = r (10 - 3 pi) / (3 (4 - pi)) (SMLib's R7 within
5e-8), and R8 less its part over the notch, integral of 2 (5 g - g^2/2), g = 8 - sqrt(64 - t^2).
- kernel tests: chamfer_wider_than_sloped_basin_rim_is_cut_and_a_full_width_one_refused:
past the 1 mm and 0.5 mm rims the chamfer runs over the slab's front edge and is cut:
the clipped triangle's area (30 + z centroid), its length 60 - h between the sloped end
walls (the same formula gives chamfer_sloped_basin_rim's fitting chamfer to 1e-12);
a chamfer as wide as the rim is refused.
- blend_corner sloped_rim_fillets_stay_inside_the_material, equal_slope_rim_loops_stay_
inside_the_material: R4 and chamfer 2 over the thin rim build, every vertex inside the slab.
- engine blend_fit chamfer_through_the_openings_is_cut_by_them: the report's 9 mm chamfer
is cut by the openings, 3350 (the rig's fillets/1080 case).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
When the kernel's room pre-check went (bcbb99005), a fillet or chamfer refused as
too large stopped saying what would fit: only SMLib's NO_ROOM words were left. The
rig expects the refusal to name it (fillets/4782-fillet-two-end-verticals-past-a-full-round:
"the largest radius that fits is 7.5 mm", fillet_max for the exact fit).
A constant fillet with the exact fit, and an equal-distance chamfer, refused as too
large now add "; the largest radius (distance) that fits is X mm", found by the same
bisection fillet_max runs (up to 16 blends, three significant digits), now shared with
a new kernel::chamfer_max. Where the search itself fails (a candidate failing for
another reason), the refusal is left as it was. The reduce and taper fits and the
kernel's own searches call the kernel blends directly and do not pay for it.
Tests: the 14 x 6 x 10 post's R3.5 names 3 mm; a 4 mm rib's crossing chamfers and
rounds at 3 name 2 mm.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
legacy_internal_capture_refuses_an_uncaptured_source_in_another_component
picked the top Offset Face raised as a face with neither a construction
certificate nor an exact history name (#494), to reach the legacy path
that refuses a profile across components while the source occurrence's
move is uncaptured. Offset Face has SMLib's history since 0f3d6f177 (shell,
offset faces and thicken through SMLib), so that top is now named exactly
(F3:+z#[F3:-x], verified) and capture_face_anchor gives it a lineage
anchor; the legacy path is not taken, and the capture is right to
succeed: an anchored attachment captures its path's pending positions
when it is made (capture_positions).
The test, renamed to what it now checks
(internal_capture_in_another_component_anchors_an_offset_face_by_its_history_name),
asserts the face still has no construction certificate, the capture is a
Lineage anchor on the occurrence's path, and capturing changes neither the
document nor the pending moves.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
explode.show put the view's placements in the uncaptured moves, so occurrence.properties reported
the exploded placement and Capture Position (and reparenting, moving bodies between components,
copying or pasting in place, URDF export) wrote the view's offsets into the design. The session
now records which uncaptured moves are the view's (Session::exploded); what reports the design's
placements or works a new placement out from them uses the design's own moves
(uncaptured_moves, design_document), while the viewport and picks still show the view.
New case cov-explode-show-keeps-the-placements: the arm's properties are the same before, while
and after the view is shown, and Capture Position keeps nothing. The two explode cases that read
occurrence.properties while exploded now expect the design's placement, centre (20, 0, 5), as the
command says ("shown only; the design keeps its placements").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Both walked the picked curve's display polyline: a point a third along an R10 sketch arc was
0.87 µm off (8.6603, 5). They now evaluate the path's exact curves by arc length: lines and arcs
in closed form, a free-form span at the parameter its arc-length integral reaches (body edges by
their record curves, 3D sketch curves by their arc, spline, line or linked exact curves; only a
curve that exists as points alone, an intersection edge or a projected curve, runs along them).
The arc's point is now within 1e-12 mm of (10 cos 30°, 5, 0).
A t outside 0…1 was clamped silently, which the contract (`t: expr, 0…1 along it`) does not
say: it is refused ("t is 1.5: a point along a path is 0 (its start) to 1 (its end) of the way
along it"). The construction cases grade the arc and line to 1e-9 mm, past-the-end is refused,
and a new case takes the middle of a symmetric cubic spline, (20, 7.5).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
When a − b or b − a cannot be made (a kernel error, or a body that encloses no volume), the
region's volume and centre are null, measured_by is "not measured" and not_measured gives the
cut's error; its deviation, area, faces and box are still given, the side's total is null and
the verdict says the volume is not measured. The integrated-along-lines estimate is no longer
reported as a volume.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
inspect.compare integrated a region's volume along sampling lines: the
40 x 30 x 5 slab between a box and one 5 mm taller came out at 5976.49 mm3
against 6000. The regions are still found from the two surfaces; each one's
volume, centre and box now come from the pieces of the exact cut a - b (or
b - a) that lie there, measured as inspect.measure measures a body
(measured_by: boolean). Where a cut cannot be made the region keeps the line
integral, marked measured_by: lines, with a warning. The rig case
cov-compare-taller-box passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
inspect.center_of_mass measured each body's display mesh, so a cylinder r 5,
h 10 came out at 784.13 mm3 against 250 pi = 785.40, and the answer moved with
display quality. It now takes the exact mass properties inspect.measure uses
(ModelBody::measure), skips bodies that enclose no volume as Measure does, and
lists what it skipped. The rig case cov-center-of-mass-box-and-cylinder passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's parallel projection (CreateParallelProjectionCurves) gives every curve where the
projecting lines cross the face: a line projected down onto a ball came back as its top and its
bottom, each split at the pole, and the link's first wire was half the bottom. A projection onto
a surface is where those lines first hit it (owner's decision, as mainstream CAD does): a curve
is now kept only when the first hit on the body's mesh along the line through its middle is the
curve itself (within 4 chord tolerances), and the pieces that meet end to end are joined in
whatever order and direction they come, a piece run the other way exactly (its knots and
control points reversed; a line's, circle's or ellipse's parameter mirrored). The ball's top
is then one wire from x = -10 to 10.
three_d_sketch_curves now expects that exact curve: one wire, its ends at (±10, 0, √300), every
point of its exact curves on the sphere of radius 20 in y = 0 over the top, to the projection's
own tolerance (a millionth of the body's size), and sweeps_and_pipes_follow_3d_sketch_curves
pipes along the whole joined top. Both pass on the pinned SMLib (90aabff): the pieces lie 9.1e-6
off the sphere against a 4e-5 tolerance and meet at the pole within 4.7e-8 rad, since the fork's
8d95600 keeps the pole's exact tangent in StepBackFromSingularity.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A symmetric surface.extrude given no convention now splits its distance
evenly around the start plane (10 mm: 5 mm each side), the way
solid.extrude reads it, instead of going the distance each way. Both
commands take their default from one function, which a session setting
(surface_extrude_symmetric_per_side) can turn back to the per-side
reading for surface extrudes. timeline.edit and timeline.redefine give a
one-sided surface extrude made symmetric the same default.
Saved designs are unchanged: every surface extrude saved its convention
(legacy_per_side), and one saved before the marker existed reads per side
as it always did. The help of both commands says how the distance is
read. The 3830 kernel case, recorded with the per-side reading, now says
so explicitly.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>