The round's centre (32 - r, 42 - r) leaves the hollow's corner (30, 40)
outside its circle, opening the wall, where sqrt2 (r - 2) = r: the case
expects the refusal naming 6.828. 2852's R30, refused naming 25.24, now
passes too: both come off the known-failing list.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The gate on aarch64 Linux reports 16 fillet cases FIXED with the pinned SMLib: the sloped and
equal-slope basin rim chamfers and rounds past their rims (1080-*, 5835-*), the pocket rim
chamfer past the floor, and the three pocket rim rounds now mitred at the pocket's corners
(every-pocket-*). No other area's gate reports a case fixed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
1080-fillet-sloped-basin-1-mm-rim-r0-5-4-edges asked G1 at every blend seam. Its front wall
leans 19 over 20 and the others 10 over 20, so at each rim corner the two mitred rounds meet the
sloped corner edge at different heights (0.155625 and 0.276393 below the top): the deeper round
runs on past the corner edge and is cut by the plane of the other's wall, a crease by
construction, the gap below the shallower round filled on that plane. The check now measures
the rounds' contact seams, on the top and on each wall, where the rounds are tangent. The
volume is unchanged.
With SMLib smlib-batch-4-mitre (1c15364): the case passes (V 144530.427946 against
144530.427909, 15 faces, sound); before it, only the four corner creases failed the check.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's trim took a fillet meeting its face at more than 78 degrees for one with no side
(smlib-batch-4-rulings 971e567); the chord of the knife edge's 0.5 chamfer meets the flat face at
81 degrees. The case comes off the known-failing list.
Needs SMLIB_REV at that SMLib once it is pushed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib (smlib-batch-4-rulings 0e83cca, SMLIB_ABI_VERSION 5) rounds the edges whose rounds overflow
their faces first and then what is left of the others; smlib_blend_dropping says which picks'
edges the overflow removed whole. The smlib crate binds it (Brep::blend_dropping), the kernel
returns those picks (fillet_removing), and a fillet notes them as its warning: "the edge at
(0, 0, 10) was removed by the larger round, so it is not rounded" (a 50 x 50 x 20 block, R21 on
its bottom front edge with the front left upright: the block is R21's alone, in closed form).
Ruling d8: [21, 5, 5] on a 20 cube builds as R21 alone (6107.529370); the test is no longer
ignored. R25 with R2 at a corner (blend_corner) builds the same way, R25's alone in closed form,
where it was refused. The rig's 1080 notched block outline at R8 builds now and comes off the
known-failing list.
Needs SMLIB_REV at that SMLib once it is pushed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With SMLib's smooth limit at half a degree (422e6f1) the 1 degree crease rounds R2 and R20
(the test is no longer ignored), and with a cusp's chamfer the ball of radius d (d231547) the
The 0.5 one stays, for its own cause (the chamfer face left apart from the body). Two corner
cases the same SMLib (replay/1.0.1 and those commits) builds come off too.
Needs SMLIB_REV at that SMLib once it is pushed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
smlib_chamfer turns the distance into a ball radius d sqrt((1 - c)/(1 + c)), c the faces'
binormals' dot (capi chamfer_radius); at #851's cusp the binormals agree, the radius is 0 and
the call is SM_ERR_INVALID_INPUT before the fillet executive runs (gdb: chamfer_edges sees
radius 0; the dump's why is empty). SolidCraft hands every chamfer to SMLib, so the
ball-contact chord (the ball of radius d: 3.822 wide at d = 2, 159.2365 removed) is SMLib's to
build.
Ruling d4 (2026-10-30).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's bar running tangent into a cylinder rounds its concave arc and
its top edge both together and one after the other in either order, at
r 1 to 7. Two more peg cases come off the fillets known-failing list.
The ladder's shelled dome ring now has 9 edges, not 7: each of its two
cylinder walls is one full-turn face with its seam edge (one wall face per
extruded circle), where it was two halves. Faces, vertices, area and volume
are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NvoxKQ2rEZvcXNQnhE3Sgs
fillets/1080-chamfer-runs-into-openings-refused already expects the
9 mm chamfer built and cut by the openings (V = 3350); its id said it is
refused. It becomes 1080-chamfer-runs-into-openings-cut-by-them, and
blend_fit's chamfer_through_the_openings_is_cut_by_them names it so.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's ruling of 2026-10-30 (d7): a chamfer that reaches or runs
past a rim builds, everywhere, as SMLib's cliff overflow builds a convex
blend: on its faces' continuations, then cut by what the cliff cuts
away. The earlier rule refused a chamfer whose leg runs off its face.
SolidCraft has no such refusal of its own; SMLib refuses these, so the
cases fail on SMLib 985faaee and are listed with its reasons (traced in
gdb at SmFilletErrorInfo::NoteError):
- the sloped basin's single front edge past its rim (1 mm rim 2 and 3,
0.5 mm rim 4): CloseRemovalRegion, "a cliff overflow's fillet boundary
lies on the surfaces of two faces": the sheet's boundary along the end
wall's top edge line from the edge's vertex to the top's contact
(x = 20, y from -1 to 1, z = 30) lies on the top's plane and the end
wall's both.
- the equal-slope basin's rim loop 2 and the 5 mm pocket's rim 5.5:
CloseRemovalRegion, "a cliff overflow's fillet boundary closes on one
face" (every edge of the loop blended).
- the sloped basin's front and right edges 2: status 1001,
SmFilletNx2Corner, CalcFilletIntSideFace.
- the cylinder's rim 2 across the top and 25 down its 20 mm wall: status
1001, SmFilletNx1ClosedCorner cannot compute its geometry.
Expectations, each from a closed form or an exact quadrature:
- chamfer_wider_than_sloped_basin_rim_is_refused becomes
chamfer_wider_than_sloped_basin_rim_builds, ignored until SMLib builds
it: the triangle clipped to y >= 0, times 30 + z (shoelace):
73.450475, 142.112912, 184.526613; the rig's 1080-chamfer-sloped-
basin-*-past-the-rim cases: V = 144459.882858, 144391.220421,
144082.140054.
- blend_corner's a_rim_loop_chamfer_running_off_its_rim_is_refused
becomes ..._builds, ignored likewise: sliced at depth t the mitred loop
takes the pocket's rectangle grown by w(t) = d (1 - t / delta) on each
side, clipped to y >= 0, less the rectangle, Simpson exact on each
quadratic piece: 375.673069, V = 139957.660264 (the rig's
1080-chamfer-equal-slope-basin-1-mm-rim-loop-2 too).
- 5835-chamfer-sloped-basin-1-mm-rim-2-two-edges: the same slicing with
the front and right sides grown, 161.279149, V = 144372.054184.
- every-chamfer-pocket-rim-5-5-past-the-floor: 50 d^2 + (4/3) d^3 at
5.5, the groove 0.5 deep round the floor included, V = 19265.666667,
15 faces.
- 2893-chamfer-two-distances-past-the-bottom: the frustum r 8 to 9.6
over 20, pi 20 (64 + 76.8 + 92.16) / 3 = 4879.102831, 3 faces.
Each drops "-refused" from its id (the 5.5 pocket's says past the floor).
The same slicing reproduces the existing 5835-...-4-mm-rim-2-2-edges
(176.006388), equal-slope loop 0.5 (24.455545) and half-width
(5.426545) values.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's ruling of 2026-10-30 (d7): a chamfer that reaches or runs
past a rim builds, everywhere. The earlier rule refused a full-width
chamfer, naming the largest size that fits. SolidCraft has no such
refusal of its own (a blend's TooLarge is SMLib's SMLIB_ERR_NO_ROOM,
and the doc layer only names the largest fit), and SMLib already builds
these, so only the expectations change, each from a closed form or an
exact quadrature:
- chamfer_wider_than_sloped_basin_rim_is_refused's full widths become
chamfer_as_wide_as_sloped_basin_rim_builds: the whole triangle,
d drop / 2 (60 - drop / 3), drop = 20 d / sqrt((20 - margin)^2 + 400)
(shoelace over the section, its length 30 + z between the sloped end
walls): 21.662379 (1 on 1 mm), 5.359321 (0.5 on 0.5 mm). The basin and
the removal move into sloped_basin and sloped_basin_rim_chamfer_removed.
- fillets/1080-chamfer-sloped-basin-{1,0-5}-mm-rim-as-wide-as-the-rim:
V = 144511.670954, 144261.307346.
- fillets/every-chamfer-pocket-rim-5-full-depth: 50 d^2 + (4/3) d^3 at
d = 5, V = 19583.333333, 11 faces (the walls used up).
- fillets/every-hole-top-rim-chamfer-10-full-depth: the triangle 10^2/2
revolved at rho = 5 + 10/3 (Pappus), V = 16000 - 3250 pi / 3 =
12596.607959, 7 faces.
- fillets/1113-chamfer-arc-top-edge-full-wall-height: the 9.5 case's
Int rho asin(21/rho) h(rho) drho at s = 10, by Gauss-Legendre in
u = asin(21/rho), 1303.400331, V = 8287.993768.
Each drops "-refused" from its id and its KNOWN_FAILING line goes: all
five pass on SMLib 985faaee.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The batch brings history Kept for a face only cut by a vertex, revolve of a
curve touching its axis, loops touching at a vertex, a torus rail on its axis,
and the fillet causes behind the owner's bar running into a cylinder: a
tangent edge past a tangent side edge is the corner's edge, the rails of a
round collapsing at its end end at one point, and a trace from a tangent point
starts along the curve.
The two peg cases with the sketch's solver residues come off the fillets
known-failing list: both build.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NvoxKQ2rEZvcXNQnhE3Sgs
This replaces the spline fallback of 64efbe7f6. A face SMLib holds as a rational spline that is
an extruded circle was recognised as a cylinder over the spline's whole parameter range: for the
upper half of the peg's wall after the front top round that range runs 393 degrees round (u in
[-15, 40.18], SMLib's support surface extended past the face), and SMLib refuses a cylinder past
one turn. The face itself, its loops' box, spans u in [0, 8 pi]: half a turn. The cylinder now
takes the face's trimmed range, the least and greatest u and v of its uses' pcurves over their
edges' intervals, found to rounding on each Bezier span (the values at the pieces' ends bound the
extreme from below, the control points from above; pieces that cannot beat the best are dropped,
the others halved). A face whose trims run more than one turn round is no face of a cylinder: it
is refused as an invalid record, never kept as a spline.
The peg (40 x 16 x 10 bar, R8 end, a disc R8 extruded 10 up on its top, joined), front top edge
rounded r2: the body measures to 1e-7 of its closed form, the three r2 corner rounds after it
build and measure, and the upper wall comes back from SMLib a cylinder of radius 8 (engine test).
The rig case of the round of the edge where that round meets the wall (tangent at one end) still
fails, for another reason: on the wall as its exact cylinder SMLib refuses the round as larger
than the faces beside its edges allow (it fades to nothing at the tangent end) instead of
returning a body its own check refuses. Its KNOWN_FAILING line says so.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A curvature-continuous fillet (type curvature, equivalent radius 2) of the three edges at a top
corner of the owner's bar built, but its corner was SMLib's own patch, which is only tangent to
the rounds: Continuity Analysis measures a 35.8 / mm curvature jump across its seams (with the
rounds G2 to the faces everywhere else), and it shows as a dome sitting on the corner, the
vertical round's shading lost under it. All three edges were rounded; the corner was not
curvature-continuous, and nothing said so.
Such a corner, where three or more rounded edges meet, is now set back (1.5 r unless a setback
names it) and left open by SMLib with the curvature sections (smlib_blend_setback_open with
SMLIB_BLEND_CURVATURE), and filled with the G2 patch fillet_g2_corners already uses for circular
rounds (fillet_g2_with_g2_corners). The `corner` option no longer leaves a curvature fillet with
SMLib's patch: its corners are always G2, and setbacks on it set back the curvature rounds (they
were circular rounds before). Where SMLib or the patch cannot build it, it is refused.
On the reported geometry every seam of the rounds and the patch is G2 (rig
report-fillet-curvature-three-edges-at-bar-corner-solver-residues), and the rounds outside the
setback cube measure exactly: V0 - 27 - (the quintic section, A2 = 0.597884, along the front edge
from 3 to the wall and along 7 and 13) = 9541.116961 (...-outside-setback). With round coordinates
SMLib's open sheet fails its own check (a 2D curve cusp, SmBSplineCurve test 13): the fillet is
refused, listed as known failing (report-fillet-curvature-three-edges-at-bar-corner).
Test: corner_g2_tests::curvature_rounds_meet_at_a_g2_corner (box corner, r5: the patch's jump
under CURVATURE_SHARE / r clear of the hole's corners, SMLib's own patch over ten times that).
Changes a default: a saved curvature fillet with such a corner rebuilds with the G2 patch; there
is no preference or fallback to SMLib's patch.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The cases from the owner's reports in the app (no issue) were named and cited after issues they
only resemble (#9, #896, #1207). They are report-<name> now and list no sources; their `what`
says where they were reported. The README gives the convention (report- for a report with no
issue or pull request, cov- for a command with no source).
report-fillet-g2-corner-of-bar-running-into-cylinder was graded by a 3^3 volume band and a face
count, which say little about a G2 corner. It keeps the band (provable: the patch differs from the
rolling ball only within the setback cube) and adds the corner seams' curvature jump, as
fillets/9-fillet-corner-r1-curvature-default-setback scaled by r = 2 (at most 0.0025 / mm, clear
of the hole's corners by 0.48 mm, within 4.4 mm of the corner). A new
...-outside-setback case cuts the setback cube [-1, 3] x [-1, 3] x [7, 11] away and grades the
three rounds outside it exactly: V0 - 27 - (front spandrel from x = 3 to the wall + (1 - pi/4) r^2
over 7 and 13) = 9342.029541. The bare face counts are dropped.
The -solver-residues recipes now take the reported sketch's points exactly (the arc's end
x = 41.649711830726524); they fail as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A 220 x 11 two-distance chamfer of a tapered plate's bottom front edge (rig fillets/5181) runs up
the front face past its straight side edges, l2|start and l6|start, and takes them up: no result
edge comes from them. SMLib leaves the blend face untagged, and it was given every blended edge
whose two faces lie next to it: the picked edge l1|start and both taken-up side edges. Its name
came from the first in edge order, F3:blend:F2:side:l6|F2:start, an edge the user never picked.
A blend face now comes from the picked edges it lies between; only a face that lies between no
picked edge's faces (a corner's piece over a short edge the corner took up) comes from the
taken-up edges it lies between. The chamfer is F3:blend:F2:side:l1|F2:start everywhere on it.
Persistent names: a blend face that also lay between the faces of an edge the blend ran over is
now named by its picked edge only. There is no alias for the old name (5181's
F3:blend:F2:side:l6|F2:start): a saved reference to it is reported lost.
Also corrects 5181's "what": the chamfer builds (335399.749), it is not refused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
An r2 round of the arc adds the spandrel ring clipped by the bar's sides, integral over rho in
[8, 10] of [2 - sqrt(4 - (10 - rho)^2)] rho 2 asin(8 / rho) = 18.455363. With round coordinates
it builds to that; with the reported design's sketch residues (~1e-10 mm) SMLib's blend fails,
status 1001 (SmFilletNx1Corner: unable to make topology at the arc's end), listed as known
failing.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The edge where a round runs into a cylinder's wall it is tangent to at one end (the bar's front
top round meeting the wall at (40, 0, 8), where the round's contact with the front face meets the
wall's tangent line with it) was refused as smooth, "nothing to round": the faces' normals were
compared at the edge's start alone, which was that tangent end. They are now compared at five
stations from end to end, and an edge is smooth only where its faces meet tangentially at every
one: this edge is a crease everywhere but its end. The wall's seam with the front face, tangent
all along, is still refused as smooth.
The round of that edge with its tangent chain (the top's concave arc) now reaches SMLib, whose
result fails its own check (internal poles, coincident control points, cusps where the round
fades out): its rig case in fillets is listed as known failing for that SMLib defect.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A round of a bar's top edge, where the bar's side runs tangent into a cylinder standing on its
round end, seemed to build: SMLib's result holds the cylinder's wall as a rational spline whose
parameter range runs 393° round (u in [-15, 40.18]). Going back into SMLib (to measure the body
or change it again) the record's extruded circles become SMLib cylinders with the face's range on
them, and that range was 6.866 rad: SMLib refuses a cylinder past one turn
(SM_ERR_INVALID_INPUT from BrepFromFlat's face range check). The body could not be measured, a
second round on it failed, and the app said one of its freeform faces can't be used. An extruded
circle whose range runs more than one turn round now stays the exact spline it is.
The bar of the reported design (40 x 16 x 10 with a R8 end, a disc R8 sketched on its top and
extruded 10 up, joined): the front top round removes the spandrel up to the cylinder's wall,
integral over y in [0, 2] of (2 - sqrt(4 - (2 - y)^2)) (40 - sqrt(64 - (8 - y)^2)) = 32.306475;
the three rounds at the other top corner after it remove 53.285832 in all (spandrels outside the
corner cube, the cube less the rolling ball's eighth). Both now build and measure to 1e-7; the
curvature corner of the three edges at once (setback 3) builds too.
Rig cases (fillets) for the three reports: the curvature corner of the three edges, the front
top round, and the three corner rounds after it pass; the same corner rounds with the design's
~1e-10 mm sketch residues fail in SMLib (its corner's surface of revolution is close to singular
at its boundary) and are listed as known failing. (Their ids take the report- convention in the
rig commit later on this branch.)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillets/851-fillet-knife-edge-tip-r2 passes on develop's SMLib (985faae): its line
leaves KNOWN_FAILING. The chamfers of the same edge still fail.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner ruled on 2026-10-30 that rounds meeting at a concave corner beside an
unpicked sharp edge are mitred, which fixes the basin loops' re-entrant corners.
Each loop case now grades its exact volume (rel 1e-6): each blend takes
Int width(z) length(z) dz, its section's width from its wall to its arc or chamfer
line (the front one clipped at the slab's face where it runs past the rim), its
length between its neighbours' walls extended; each corner of two picked edges adds
the overlap of their section prisms in the quadrant beyond both walls,
Int width_1(z) width_2(z) dz (r^3 (5/3 - pi/2) for vertical walls, as
every-pocket-rim-edges-r2). One edge alone reproduces the single-edge closed forms to
3e-7 of the removal. The equal-slope chamfer loop 0.5 passes; the others stay on
KNOWN_FAILING with the causes they had (SMLib status 1001, the surface-of-revolution
check, rounds past the rim not built by subtraction).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The 851 table rows grade continuity again, on each round's seams to the faces it
rolls on, picked by points at the middle of its edge (the top front round's at
z = 8 on the front and y = -19 on the top, the arc's at rho 23 and rho 21, the
uprights' at their contacts). The default `blend` selection read G0 there because
it pairs a blend face with the contact faces of every edge in the feature, so where
a round ends square on another edge's contact face (a crease by construction) it was
graded as a tangent seam: a gap in the grader's seam selection, worked around here
by naming the seams. All seven rows pass.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillets/1668-fillet-outer-top-edge-of-thin-wall-r7-past-inside-corner (and the
both-sides R7 case) now grade the volume at rel 1e-6 (0.04 mm^3), not the rig's
1e-3. The closed form is exact: V0 = 104 64 42 - 100 60 40 less the round's
section (1-pi/4) 49 along 104 plus its part over the hollow, the square
[25,30] x [35,40] outside the circle about (25,35), Int_sqrt24^5 (5 - sqrt(49-u^2)) du
= 0.0050679 mm^2 (a 0.0005 grid gives the same to 1e-9), along 100: 38458.896.
SMLib gives 38458.389, 0.507 mm^3 less: exactly that part over the hollow, which is
not material, taken anyway where the round opens its slit. The unit test's bound
was right; the case goes on KNOWN_FAILING with that cause. The both-sides case
passes at the tighter tolerance.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The fillet and chamfer unit tests that checked geometry become fillets rig cases,
built through commands with answers derived by hand (each method field gives the
derivation): a plate outline and a disc rim as tall as or past their wall, a
notched block's outline at R7 and R8, a cube corner as wide as its faces (refused,
and reduced), the 1668 wall at R7 alone and both sides, the 2852 U shell at R30
(refused, naming 25.24), the 851 knife edge (R2, chamfers 0.5/2/5 on three
constructions), the arc top edge at the full wall height and at 9.5, the 851
table of selections, the 556 top edge ending on the boss wall, the 2893
cylinder-rim chamfer refusals and the elliptical rim, seed 33's full round, the
sloped basin rim blends (single edges with exact volumes, loops with the slab's
box), and three action-matrix chamfers and fillets. fillets/851's three-edge
corner gets its volume (67.051 removed, re-derived on a grid; the engine test had
67.05). Chamfers whose leg runs off the face beside the edge are refused and rounds
past a face on its tangent side build, as the owner ruled on 2026-10-30. The cases
that fail today are on KNOWN_FAILING with their cause.
The unit tests are removed, except two cut to what no command can express: the
per-edge-radius refusal at a cube corner and the chamfer of a cylinder's seam.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
a_round_into_a_hole_is_cut_by_it (issue_324_tests.rs) built rig case
fillets/324-fillet-over-hole-overlap's body, but cut its hole with a cylinder
longer than the block (z -1 to 11) where the rig extrudes a sketch circle
flush. The new case fillets/324-fillet-over-hole-cut-by-overlong-cylinder
builds it that way (solid.cylinder, base z -1, height 12, cut) and holds it to
the same hand-derived answer: block 40x20x10 less the r3 hole at (20, 14.5)
(282.74) less the R4 round on the top edge at y = 20, 40 (16 - 4 pi) = 137.35,
plus what both remove, the integral over y in [16, 17.5] of
(4 - sqrt(16 - (y - 16)^2)) * 2 sqrt(9 - (y - 14.5)^2) = 0.375830 (re-derived
with the substitution y = 17.5 - s^2, 200000 steps):
V = 8000 - 90 pi - 40 (16 - 4 pi) + 0.375830 = 7580.287315, and G1 on the
blend. It passes today (aarch64, SMLib), as the flush case does, so it needs no
KNOWN_FAILING line; the unit test, a duplicate of the two cases, is dropped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A box edge chamfered 2 and by two distances (3 and 1, and flipped, told apart by the
centre of mass); a pocket's rim chamfered 1, by two distances, 4.9 (fits), and 5 and
5.5 (refused by the owner's rule on full-width chamfers: built at 5 today).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A box edge rounded, then the edge meeting it at the corner, in both orders (both the
three-edge rolling-ball corner); r3 then r2 (the r2 round's torus about the r3 round's
axis, by Pappus); an L-bracket's front inner outline after its bend round; a block's
top edge after the arc round at the cylinder (fails today: G0 at the round's end on the
crease); a curvature round after a curvature round with Tangent chain off.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Inside bend r3, outside r5, both concentric (r3 and r8), the inside r35 using up both
inside faces, r36 refused naming 35, and the inside bend Type: Curvature.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Top and both rims rounded r1 and chamfered 1; the top rim rounded r10 (as deep as the
plate), r12 (past it on its tangent side: built by subtraction, fails today with
status 1001) and Type: Curvature; chamfered 9.9 (fits) and 10 (the full depth:
refused by the owner's rule, built today). Volumes by Pappus.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A rectangular pocket's floor edges, rim edges and both rounded r2, the rim r5 as deep
as the pocket; a boss's root r2 and r10 (as tall as the boss) and its top rim r2.
The rim cases fail today: SMLib puts a corner patch where two rim rounds meet at a
concave pocket corner, where the rounds running into each other make a mitre (four
faces more; the volumes agree to 5e-4).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A block whose sides meet the cylinder at creases: the concave arc at the wall above
the block's top r2, the cylinder's top rim r2, the block's long top edge r2 with
Tangent chain off and Type: Curvature. A block as wide as the cylinder, its sides
running tangent into the wall: the arc and the long top edge each rounded alone
(built or refused as continuing tangentially). Volumes by Pappus or one-dimensional
quadratures of the exact sections, the round ended by the planes it runs into.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Three edges at one box corner rounded r1 and r3 with the rolling-ball corner, r3 with
Corners: Curvature at its default setback and at 3.5, and refused at 3 (the radius);
the corner chamfered 2; all twelve edges rounded r2; one edge rounded Type: Curvature.
Volumes in closed form (strips plus sphere octants, half-space intersection, the
rounded box as a Minkowski sum, the quintic section's area 113/756 s^2); G1 at every
round's seam, G2 for the curvature round and the corner patches.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillets/4782-fillet-two-end-verticals-past-a-full-round passes: SMLib (90aabff) refuses
R10 on the 15 mm wide box's two end verticals as too large, and the refusal now names
the largest radius that fits, 7.5 mm (the full round). Run on aarch64 Linux with
--known-failing: every other fillets case as listed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Where a round meets a plane it is only tangent to it: its curvature jumps by 1/r there, so no
corner patch can be G2 to both at that point. The cases graded the whole seam and could not pass.
They now bound the curvature jump at stations clear of each seam's turn, within reach of the
corner, scaled by r (ladder 07/019's bound at r5): r1 within 2.2 mm, 0.24 mm clear, 0.005 per mm;
r5 within 11 mm, 1.2 mm clear, 0.001 per mm. Develop's corner gives 0.00135 and 0.00027 per mm
(the jump at the vertex is 1.017 and 0.2035, the round's own 1/r), so both leave KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A plan job (scripts/ci/kernel_rig_plan.py, with its self-test) maps a pull request's changed files
to the areas: tests/kernel-cases/<area>/PATHS for each area, tests/kernel-cases/PATHS-ALL for the
shared core, the ladder whenever any area runs. Areas come from the folders, so a new one needs no
workflow edit. Pushes, merge groups, the release gate and runs by hand run every area. The
kernel-rig check counts a skipped build or shard as passed only when the plan selected none.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With SMLib integration-overnight + b78bd4a (the fixes of 2026-10-29), three
expectations that held a refusal now build, each checked against its exact answer:
- rig fillets/1207-fillet-box-end-edge-into-unblended-round (was ...-refused): the end
face's top edge of a cube rounded r3 along its top back edge, rounded r1 alone
(tangent chain off), builds. Its round runs on along y through the r3 round's end
until that surface drops below it at y = 17 + sqrt(5): V = 8000 - 20 (9 - 9 pi/4)
- 17 (1 - pi/4) - 0.218236 = 7957.505202 (the last term the section under the round,
integrated exactly); SMLib gives 7957.505245.
- blend_smlib smooth_edges_and_unfinished_tangent_chains_are_refused_saying_why: the
same cube builds, at that volume.
- modify_history_tests::smlib::draft_tilts_a_side_and_keeps_its_name: the rod's side,
a cylinder along the pull, drafts 5 deg to a frustum, radius 5 at the neutral plane
and 5 - 10 tan 5 deg at the top, at its exact volume.
tests/kernel-cases/fillets/KNOWN_FAILING drops 1557-fillet-vertical-corners-after-
bottom-rounds, which passes now; the other eight still fail, so the gate holds
(81 pass, 8 known failing, no regression).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Ten cases the pin fixed leave the list (the 1207 corner patch and its together cases, 1390,
4782 reduce-fit, 896). 1557 joins it with its cause: since bodies are read back from their
records (#8625) its bottom rounds come back as SmCylinder where SMLib's blend made SmCone(0),
and the corner-ball trace starts 2.78e-4 off; its fix is in progress.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
New: an r5 curvature corner at a box corner (its patch must seam G2), an
edge running tangentially into a round left out (refused: continues
tangentially), a convex r10.01 round 0.01 past a 10 mm face (built by
subtraction: V = 7139.875, A = 2585.140). The bar and boss arc rounded
together say their crease (15.6 deg r2, 13.1 deg r1); 1390 expects SMLib's
unsupported-corner refusal, the honest reason today; past a full round
the exact fit's refusal names the largest radius that fits, 7.5 mm.
KNOWN_FAILING lists the 18 of 89 fillet cases failing today, each with
its cause.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
expected.json may give `continuity: {order: g0…g4, edges?: "blend" | "corner"}`: the
seams of each round, chamfer face or corner patch with the faces either side of the edge it
replaced, and of each corner patch with its rounds, are measured as Continuity Analysis
measures them (seam_diagnostics at its default 33 stations and default tolerances), and the
case fails naming the worst seam, its faces, the order it reaches and the next order's worst
value. The seams come from the faces' persistent names (doc::naming::blend_seams). The older
`{near, within_mm, …}` form is kept.
Every fillet-area case with a body gets its order: constant rounds and rolling corners g1,
curvature rounds g2, chamfers g0, the corner: g2 patch g2 at its seams.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A corner setback must reach past where the corner's rounds' contact lines
meet without one (smlib_blend_setback); short of it SMLib failed with its
own status (1001). The kernel now refuses it before SMLib runs, for the
rolling-ball corner (fillet_setback) and the curvature corner
(fillet_g2_corners) alike, naming the least: on each face at a corner of
planar faces and straight edges the two rails, r tan(psi/2) from their
edges, cross (d2 + d1 cos alpha) / sin alpha along an edge (r on faces
square to each other). Other corners stay SMLib's to refuse.
The rig's `refused` cases now name the reason (`refusal`, a part of the
message, required), so a failure for another reason no longer passes; a
`solid_or_refused` case may name one. Fillets: the setback cases and
783, 3435 pass; 1390, 896, 4782 past-a-full-round and the no-tangent-chain
case are refused for an unclear reason and fail.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
22 hand-written cases in tests/kernel-cases/fillets:
- 1207-fillet-bar-top-edge-and-boss-arc-together (r2, r1, fit reduce,
fit taper, curvature corners): a bar's top edge and the partial base
arc of a boss standing out over the bar's side rounded together. The
rounds' volumes away from the corner, the corner patch within (2r)^3.
SMLib's 3x2 mixed corner fails here (1001) until the fork's fix.
- 1207-fillet-bar-top-edge-after-boss-arc-round (r2, r0.5, no tangent
chain): the edge rounded after the arc; r0.5 fails SMLib's check.
- 9-fillet-corner-*: setbacks not past the radius refused (rolling and
curvature corners), the curvature corner at r1, and the curvature
corner with reduce and taper fits (not supported yet).
- 4782-fillet-*: full rounds (two end verticals at half the width, exact,
reduce, taper), a round at half the wall, radii past the full round
(refused; reduce gives the full round) and a round wider than both
faces (built by subtraction).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib now builds a round or chamfer whose rail runs off its face across a cliff (an opening's
rim, the body's outline): the blend is made as if its faces continued and what it removes is
subtracted, so it never bridges an opening (owner decision for rig 5158/5181; fork commit
"SMLib, capi: a convex blend overflowing a cliff is subtracted from the body"). The tests that
expected a refusal for such blends now expect the body, each answer from the geometry:
- variable_radius_on_a_box_edge: 2 -> 50 on the 10x20x30 box's top edge builds at
3546.18767939 (circular sections in y = const, the r x r square less the quarter disc,
clipped to the box; rel 1e-4).
- variable_radius_from_a_spline: the "big" law builds at 6000 - 726.5334566720 (de Boor law,
split at the knot and where r crosses 10).
- a_chamfer_meets_sloped_end_planes: chamfer 25 removes 11500 - 4625 * slope
(integral of 40 - 2 * slope * y over z >= y - 5).
- g2_fillet_refuses_invalid_geometry: G2 at 25 builds at 6138.1606889 (the quintic section
with control points at thirds, clipped to 20x20, along 20).
- fillet_max_each_reduces_only_where_the_radius_does_not_fit: both edges take 4, 24438.7317761.
- hostile_inputs_are_errors: chamfer 30 on the cube builds at 1000 (y + z <= 10 along 20);
R50 still fails.
- kernel-cases fillets/1080: the 9 mm chamfer into the openings builds at 3350
(method in expected.json).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_0113gDVmStT5tCGKW9Fxgc5K
Cases from the issues filed after #4160, each a synthetic recipe with its own answer
(analysis or invariants); every other issue in the range is listed with why it was skipped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Cases from the issues filed after #4160, each a synthetic recipe with its own answer
(analysis or invariants); every other issue in the range is listed with why it was skipped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Cases from the issues filed after #4160, each a synthetic recipe with its own answer
(analysis or invariants); every other issue in the range is listed with why it was skipped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Cases from the issues filed after #4160, each a synthetic recipe with its own answer
(analysis or invariants); every other issue in the range is listed with why it was skipped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A tray with seven rounded edges, both rim rounds of a tube, a chamfer on
a joined L-shaped body, and a circular pattern of a chamfered hole, each
with an analytic volume.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Every other fillet, chamfer and blend issue and PR, one line each: auto-filed reports from private designs (picks and error only), sketch fillets and chamfers, UI, previews and navigation, feature and fit-option requests, reference cases that already exist in tests/oracle, surface modelling, and failures that belong to booleans, shell, import, tessellation, sheet-metal or threads.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
The graded volume was right; the derivation text quoted the union as 46476.5 instead of 45571.7.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>