* STEP import: mesh band faces that wrap around a closed surface correctly
Fixes two related bugs that caused SolidCraft to fail to mesh a face wrapping
all the way around a closed, non-periodic surface (a revolved ridge band, or a
tube-shaped B-spline surface): a missing face, a folded/self-overlapping
triangulation, or a hole in the rendered body.
1. Ring edges that run slightly off their surface. STEP files write a surface
and the curves bounding it to the file's own declared uncertainty, so a
ring edge can legitimately sit a few micrometres off the surface it
bounds. The code finding where a ring edge crosses the planned split line
compared against the edge's raw (off-surface) point using a hardcoded
tolerance far stricter than the file's own precision, rejecting a valid
cut. Now matches against the point on the surface directly below the ring
crossing, respecting the file's declared tolerance.
2. Closed B-spline surfaces, their slits and their slivers. truck only treats
the rotation of a revolved surface as periodic; a face on a B-spline
surface whose control net closes on itself (a tube) wasn't recognized as
wrapping around at all. This produced a folded face, a hole (a boundary
loop landing a full period away from where it should cut), and one
near-zero-width sliver face costing the entire body its tessellation
plan. Adds periodicity detection for closed B-spline surfaces, period-
aware hole-loop alignment, dropping of zero-width slit boundaries, and
isolating a too-thin-to-triangulate face so it no longer takes the rest
of the body down with it. The GPU shader's periodic wrap mirrors the CPU
math so the two don't drift apart.
Regression tests: band_faces_split_when_ring_edges_run_off_their_surface,
band_face_with_a_zero_width_slit_is_still_meshed,
a_sliver_face_too_thin_to_triangulate_does_not_cost_the_body_its_plan.
Ablation-tested: disabling either mechanism in (2) reproduces its target
test's original failure message while leaving the other test unaffected.
* STEP import: mesh the band's split faces, not just split them
jyviko asked whether a band wall missing from the interactive app's render
was a shading issue or a genuinely missing face. It was missing: the ring-
edge split fix made the band's topology correct, but plan_face still
produced zero triangles for the two new sub-faces.
Two causes, both in plan_face (crates/kernel/src/tess/mod.rs):
1. The tolerance for how far an imported boundary may lie off its surface
was tied to the requested mesh's chord tolerance instead of to the
body's own size. A finer display tolerance could then reject a boundary
a coarser one had just accepted, so the face would drop out exactly when
zooming in on it.
2. Near a sharp corner of this flat-panelled band, several boundary points
that are legitimately a few micrometres apart (within the STEP file's
own declared precision) all projected onto the same surface point. The
boundary loop then repeated a point in (u, v), which a triangulator
can't follow, so the face's plan failed outright. One face without a
plan costs the whole body its plan, and the fallback mesher can't
handle a closed B-spline surface either, leaving both halves of the
split band with no triangles at all: present in the topology, invisible
in every renderer, and absent from the body's volume.
Fix: scale the off-surface tolerance to the body's own extent (new
Rules::extent), and collapse a run of boundary nodes that land on the same
surface point to one (drop_collapsed) before triangulating.
Regression test additions to band_faces_split_when_ring_edges_run_off_their_surface:
the body's volume now matches the analytic pentagon prism (was a third of
it - only the top cap - before this fix); display_plan leaves no face
without triangles from coarse to fine tolerance; and the actual tolerance
and facet angle the viewport draws with gives the split band its full
lateral area on both halves.
Confirmed on review_band_big.step, the fixture behind the review screenshots:
volume's relative error against the analytic pentagon prism drops from
1.4e-4 to 4.1e-6, and the band wall now occludes the floor grid behind it
in a snapshot the same way the top and bottom caps always did.
Full kernel suite: 739 tests, 0 failed.
* STEP import: hold an imported boundary to the file's own tolerance, not the part's size
jyviko: the off-surface acceptance added in the last commit
(rules.extent * OFF_SURFACE) scaled with the part, so a 2 m part
silently accepted a boundary 2 mm off its surface while a 20 mm copy
of the same part accepted only 0.02 mm. A STEP file's own declared
uncertainty does not grow with the part, so the bound shouldn't either.
Body gains boundary_tol: Option<f64>, Some(file's declared tolerance)
for a body read from STEP (crate::step_in::Units::tol, already used
by the ring-split fix in split.rs), None for anything this kernel
built. It's set before the import's own unmeshed-face check runs, and
carried over by the two face-split operations that re-cut an imported
surface (splitface.rs, outline.rs), since the file's uncertainty still
describes those boundaries afterward.
plan_face's accept now reads: the file's own tolerance when the body
declares one, or the old chord-tolerance/extent bound otherwise. The
old bound's tol * 10.0 term had to go too, not just the extent term:
at a 2 m part's typical display tolerance that term alone is ~20 mm,
nearly ten times the extent bound jyviko objected to, so keeping it
would have left the exact 2 m/2 mm example still silently accepted.
Two new tests in step_in/tests.rs:
- band_faces_split_when_a_scaled_copy_runs_off_its_surface: the same
band fixture at a realistic 2 m scale with the same absolute slop
and declared uncertainty as the small one, meshes the same way at
every chord tolerance from coarse to fine.
- off_surface_budget_follows_the_file_not_the_part_size: the actual
regression. The same off-surface error is accepted or refused the
same way whether the part is 20 mm or 2 m; a 2 mm error against a
1 µm declared uncertainty is refused at both sizes now (accepted at
2 m under the old bound, refused at 20 mm - that asymmetry was the
bug). Checked at both a coarse and a fine display tolerance.
Known gap, not fixed here: a STEP-imported body saved into a
.solidcraft design and reopened loses boundary_tol (native.rs's
decoder has no field to read it from) and falls back to the old
extent-based bound on reload. Today's design format has no concept of
this value at all; persisting it is a real format change, out of
scope for this fix.
Full kernel suite: 776 tests, 0 failed. clippy -D warnings clean.
* Display plans for STEP threads and pointed ends (#3847)
Three faces cost a threaded or pointed STEP part its whole display plan, so it
was drawn from the reference mesh: cracked, faceted, and never refined up close.
- A loop through a pole (a cone's apex on the boundary) seemed to wind around
the surface: the jump at the apex, unwrapped to the nearest copy, was
arbitrary. The loop is turned to end where it leaves the pole, so the step
that closes it is an ordinary one (`seam::close_through_pole`).
- Projection onto a spline with hundreds of spans (a helical flank) restarted
from a 16 x 16 grid and settled on another turn; it now starts from two
points per span, capped.
- Sag refinement no longer inserts a point exactly on a boundary side, which
split the side and failed the face.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* tess: a refused face's edges are divided finer and it is planned again (#2814)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* tess: sliver faces plan empty; a face no method plans is filled flat from its nodes (#2814)
A face whose boundary runs out and back along itself (two edges between the
same vertices, a rounding apart, as STEP files write slivers) encloses nothing
and is planned with no triangles. A face still refused after its edges are
divided finer (a cusp, a sliver whose sides sag across each other, a small cap
at a pole) is filled flat from its shared boundary nodes, so the rest of the
body keeps its display plan instead of falling back to the reference mesh.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* display mesh tests: a rim the chord tolerance leaves a line is divided again (#2814)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* portable B-rep: up to 8192 control points along a spline direction (#2814)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* solidcraft-cli: --debug logs what the engine reports to stderr
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* STEP import: a spline written over a tiny parameter range is read over one (#2814)
Some writers parameterize splines over a few millionths (a humanoid robot's
edges span 5.4e-6). The kernel tells parameters apart only to 1e-6, so over
such a range it evaluated the curve's end wrongly, and trimming an edge to its
vertices dropped a control point: the bodies could not be stored exactly and
the whole model cache was left out of the design. The knots are now stretched
to span one; the curve is the same and edges are trimmed by their vertices, so
nothing read from the file refers to the old parameters.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* model cache: a body keeps its file's declared accuracy (#2814)
A body restored from the cache dropped the accuracy the file it was read from
declares, so the planner held its boundaries to the kernel's own bound and a
reopened design drew differently from the import. It is stored with the body's
runtime values, and only when there is one.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* tess: a boundary within a hundredth of its body lies on its surface, at every quality (#2814)
#1721 held a body read from a file to the accuracy the file declares. A writer
declares what it aims for, not a bound its edges keep: a 251-body robot
assembly declaring 0.01 µm has boundaries 10 to 30 µm off their surfaces, and
95 of its bodies lost their display plans. The bound is a hundredth of the
body again, what Normal quality always allowed, and now the same at every
quality, so zooming in still never drops a face (#1721's point). A file
declaring more raises it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* STEP import: keep faces whose edge vertices sit slightly off their curves
Some exporters write an edge's vertex beside the end of its curve, further off
than the accuracy the file declares (a surface export declares
0.01 mm and puts a vertex 0.19 mm off two spline ends). The reader refused
such edges and left the face, and with single-face bodies the body, out.
A vertex may now sit up to the file's tolerance or 1/1000 of the model's size
(the diagonal around its VERTEX_POINTs), whichever is larger, never more than
the existing 1 mm ceiling. Spline and open-conic edges have the end control
point moved onto the vertex, so every such edge meets its vertices exactly.
The file's declared accuracy still governs closed-curve, seam and circle
checks.
* tess, io: review clean-ups (#2814)
- A sliver face is one whose loops are all slit: drop_slits finds it in the
retry after a failed plan, so the pre-check on every face (folded) is gone.
- The flat fill uses cdt::triangulate (a lenient fill that leaves out sides
crossing one already kept) and its flood-fill inside test, and the plane
from geom::Plane.
- Refinement only builds its indexes when a face was refused, takes the
faces to plan again from edge_faces, and re-samples edges on the pool;
Rules::finer for the finer rules.
- One PackageWriter::fits for the model cache, the preview and the thumbnail.
- The band split's ring tolerance lives in split.rs; comments say what the
off-surface bound is now.
- The CLI logger prints Level::as_str().
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
---------
Co-authored-by: David Lackovic <lackovicdavid1234@gmail.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Ray <raykholo@users.noreply.github.com>
Hovering an edge lights its circular rim, which starts from the edge's
tangent chain. That looked at every edge of the mesh for each edge in the
chain (and searched the chain itself each time), so a long helical edge in
many pieces, a thread's crest, took seconds: 7.6 s inside the frame on the
first hover of the stem's thread in a real watch-movement STEP file. The
edges are now found by the grid cells of their ends, two join tolerances
across, so each step looks only at the edges that end near it: the same chain
in the same order, in 29 ms for that thread.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Iterate instead of indexing in nine loops
Replace index loops that look up neighbours by position with enumerate,
zip(cycle().skip(1)) for wrap-around pairs and zip(skip(1)) for
consecutive pairs. No behaviour change.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: ring_edges for the edges of a closed ring
Every walk over a polygon's edges, the last back to the first, spelled
x.iter().zip(x.iter().cycle().skip(1)); eighteen of them now call
geom::ring_edges. Three redundant take(len) calls go with them.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Ring, a closed ring that knows it is closed
A Ring holds items in order around a closed polygon, loop or fan; edges()
walks each with the next and the last with the first, corners() each
with both neighbours. Ring<Vec2> has signed_area and even-odd contains.
Loop2::polyline returns a Ring, as do doc's face_loops and
boundary_loops, kernel's coplanar wire samples, CapLoop's segments,
tess pieces' rings, the gizmo's plane quads and the navigation cube's
facets. Their walks take edges() or corners() instead of wrapping an
index; sketch's text-hole test and doc's poly_area become contains and
signed_area. Loop2::joints pairs each segment with the next.
Replaces the ring_edges free function.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Chain, Ring and Path; bounds for a chain of points
Ring becomes Chain<T, Closed> beside Path = Chain<T, Open>: edges()
closes a ring and stops at a path's end, Path::close makes the ring,
and bounds() (the empty box for no points) serves both. Eight
hand-rolled min/max folds over a loop's polyline call bounds(); doc's
flat_polyline returns a Ring.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: area and inside on Ring for any planar point
Ring's signed_area and contains take any Planar point (Vec2 or
[f64; 2]). The cam profile in joints_cam is a Ring: its own even-odd
test goes, and its edge walks, gap and area take edges(). face_params'
loop area, the text path's winding, tess pieces' ring area and the
copies in three tests call signed_area or contains; the formulas are
the same term for term.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* doc: sheet's closed outlines go through Ring
dedup takes and returns a Ring (dropping a last point back on the first
is what makes it a ring's), near_outline walks a Ring's edges, and the
copy of it beside fold checks calls it. point_in goes: its callers ask
the Ring. Its formula anchored each crossing on the other end of the
edge, so the two can differ only for a point on an edge to the last
digit; one caller sets such points aside first, the others test a
region's interior point, a cut's midpoint or another outline's corners.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* doc: cam tests build their outlines with Ring::from
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: area_vector on Ring<Vec3>; three Newell sums use it
Ring<Vec3>::area_vector is half the sum of a × b round the ring. heal's
loop_area, lip's outer-loop turning and the revolve's loop orientation
summed it by hand with a wrapped index; they take it from the Ring
(the half is exact, and two of them only read its sign).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Aabb3 from points; boxes built and asked through it
Aabb3 collects from points (skipping non-finite ones, as add does) and
gains inflated, contains and meets. Fifteen hand-rolled min/max folds
over points or boxes in kernel, doc and engine become collect or union,
and their "within tol of the box" tests become inflated(tol).contains.
blend's refused-edge boxes and naming's face index hold an Aabb3.
A NaN point is now outside every box, where the old negated
comparisons let it in; an infinite point no longer stretches a box.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Aabb2, the plane's box; 2D folds and box tuples use it
Aabb2 mirrors Aabb3 (collect, add, union, inflated, contains, meets)
and adds relative, a point's place in the box. sketch's link and
link_loops each had that formula; link_loops' boundaries, prism's
segment and loop boxes, profiles' shape boxes and grid, and ends'
segment box hold an Aabb2 instead of a (low, high) pair. Folds in the
cam, sketch bounds, sheet's perforation grid and the sketch clipboard
collect one.
Boxes are built from the same terms (a round's box keeps c - r - tol).
As with Aabb3, a NaN point is outside every box and an infinite point
no longer stretches one.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* kernel: prism's segment boxes are plain Aabb2s
The SegBox alias named a (low, high) pair; Aabb2 says it itself.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Chain::bounds is an Aabb2; the boxes #2382 left as pairs follow
Chain::bounds returns an Aabb2. Its callers keep it: sheet's hole and
cut boxes (loop_box), letter boxes, island outlines and line-near-cut
test use meets, contains and inflated; profile's outline overlap and
max_clearance, profiles' box tests and the cam test read its corners.
flat_size and the flat pattern's JSON size are the union of the loops'
boxes (0 × 0 for no loop, where the pair fold gave -∞).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Aabb3::intersection; hand-grown and hand-met boxes use the box
Aabb3::intersection is the box both hold. ops' four overlap boxes of a
boolean's operands take it, and seven boxes grown by hand (ops' body
boxes, the distance set's bounds, coplanar's face box, eval_more's
padded mesh box, compare's group and region boxes) call inflated with
the same amount on every side.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* Model cache written by default: exact bodies, stored once, scaled caps (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* bench-open: say why bodies were not kept
* Exact planes and revolutions; budgets for large bodies (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Native B-rep: rebuild shells as the kernel made them (closed and seam edges) (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* docs: the model cache and the exact native B-rep (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* bench-open: time a save without the cache too
* Model cache entries are Deflate-compressed (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Model cache: one that does not fit the design file is left out, never a failed save (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
World placement already shares a part's reference mesh between its
occurrences (#2924), but the display plan the GPU viewport draws was made
again for every occurrence from its placed B-rep: planning every face of
every instance of the part. A placement now carries the definition's plan
cells too, and a placed body's plan (and its CPU mesh) is the definition's,
moved by the placement's matrix (`TessPlan::transformed`): the part is
planned once however often it is placed.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Boolean: a pin in a bore of its own size is clear of it, whatever its facets
A pin whose wall is in other faces than the bore's (turned from a profile: three
faces; the bore two) is faceted at other angles. Where one body's faces end on
the shared cylinder (the pin's wall through the end face of the tube, the pin's
end inside the bore) the facets cross by the facetings' error, so the sampled
shortcut doubted its own "apart" answer, every retry failed on the coincident
walls, and the result came back unverified after seconds: inspect.clearance
left such pairs unchecked ("could not be intersected there").
The shortcut now leaves out crossings that lie on a cylinder both bodies have
faces on (axes and radii within the kernel's same-surface tolerance, where both
faces run). A pin a hair off its hole's axis, or one pushed into a narrower
bore, is still not taken for apart.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Boolean: skip only the shared cylinder's own crossings, not a flat along it
The shortcut left out every crossing near a cylinder both bodies have faces
on, from any face: a pin through a D-bore whose flat is 0.022 mm inside it
came back as contact. Mesh::crosses_except now hands the predicate the two
triangles' faces, and only crossings between the faces on the shared
cylinder, or between one of them and an end face across its axis that keeps
to its body's side of the cylinder (within the facetings' error), are left
out. The D-bore's end face reaches into the cylinder to the flat, so the
pin's wall through it counts again; a flat, key or rib along the axis always
counts.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Boolean: a pin in a bore of its size is clear at every placement
The sampled shortcut's check that no facet has material under it on the
wrong side of the other body still caught the facetings of a shared
cylinder. A facet of a pin's end inside the bore (or of the bore part's
end face round the pin) with all three corners on the rim has its middle
just inside the cylinder. Where the other body's chords reach further in
at that angle, the point under it lies inside the other mesh, though the
bodies only touch. Which facets do so depends on the face splits and the
placement, so the same pair read as clear at one placement and as "not
verified" at another.
Such points are no evidence now when they lie on the shared cylinder,
under a facet of one of its end faces: the end faces and band the
crossing check already leaves out. A pin 0.02 mm larger is no shared
cylinder, and its overlap is still found.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* geom: UnitVec3; a face's analytic axes and normals are unit by type
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: UnitVec3 adds to and subtracts from a Vec3
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* kernel, doc, engine: cylinder axes and measured normals held as UnitVec3
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* kernel, engine: functions that take a unit axis or direction say so by type
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* doc: a face's normal goes to Plane::from_normal as is
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* kernel, doc: main's new cylinder helpers take the face's axis as a UnitVec3
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* feat(geom): surfaces through curve networks, and spline spaces to build them
Adds spline_space (clamped B-spline spaces, Hermite interpolation, exact
embedding by Bézier degree elevation and knot insertion, a monotone cubic
for reparameterising) and network (loft, Coons and Gordon surfaces through
curves in one or two directions, with G1/G2 cross-boundary conditions
against a neighbouring face). Part of #763.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* feat(kernel): boundary surfaces from sketch curves, 3D curves and edges
kernel::boundary_network turns sketch chains, 3D sketch polylines and edge chains
into network curves, gives G1 frames of the faces along open edges
(EdgeFaces), builds the B-spline face (sides split at chain vertices so a
join shares the body's edges) and joins it into a surface body by stitching.
G2 is refused for now (not supported yet). Part of #763.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* fix(kernel): second derivatives of B-spline surfaces in the vendored truck-geometry
BSplineSurface::uuder and vvder multiplied the second differences by p
instead of p·(p − 1), as BSplineCurve::der2 does, so every surface of
degree p ≥ 3 (NURBS too, through its homogeneous surface) reported
1/(p − 1) of its second derivative: a cubic surface's curvature read as
half. This is why a G2 boundary surface on a cylinder measured half the
curvature it carries (#763). New tests hold both to finite differences
for degrees 2 to 5.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* feat(kernel): G2 boundary surfaces against a body's face
The network always carried the face's curvature across a G2 edge; the
refusal came from measuring it with truck's halved surface second
derivatives (fixed in the previous commit). EdgeFaces now reads the
face's second fundamental form from the exact second derivatives
instead of differencing the normal. A new test holds the curvature
across a cylinder's edge to the cylinder's within 0.1%, also with a
sheared far curve; G3 is refused (a network holds up to G2).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* test(kernel): a boundary patch with straight corners measures its own area
A stadium's arcs meet its lines at 180°, so the Coons patch is singular
at its corners. From such a corner the reference mesher's boundary walk
ran onto the B-spline's extrapolation past its domain (a planar spline
passes through every point of its plane there), and the face measured
289 mm² for its 158.5 (#763). The vendored mesher's bounded projection
(nearest_projection, #2043) keeps the walk on the domain; this holds it
there, by the faces, the measuring mesh and the display mesh. The
display path (#1653) was never affected.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* feat(geom,kernel): three-sided boundary surfaces (one side collapsed to a point)
A network curve may be a PointCurve: the apex where the two sides beside
it meet. The curves through it cross it at the point itself, its row of
the net collapses there, and the kernel's face leaves that side out of
its loop (three edges, one vertex at the apex). One point per patch, as
a side; refused elsewhere, when it moves, or with a continuity
condition. Tests: a triangle and a quarter disc filled flat with their
analytic areas (40 mm², 25π), by geom and by the kernel's faces and
meshes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* feat(doc): boundary surfaces through curve networks and loops of three or four
FeatureKind::SurfaceNetwork saves a network as `u` and `v` curves, each
a sketch chain (planar or 3D), a chain of a body's edges with an
optional G1/G2 continuity, or a point (the apex of a three-sided
patch), and an `operation` that can join the surface into the body of
its edges. A SurfaceBoundary of three or four sketch curves, refused
until now, builds as the flat Coons patch of its loop (three collapse
the side opposite the first curve). The format change is one pending
file; feature-walk goldens record the new variant's sketches, bodies
and points.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* feat(engine): surface.boundary through loops of three or four and curve networks
The command keeps its loop form (two to four curves of one sketch; three
and four now build the flat patch of the loop, crown refused there) and
gains a network form: `u` and `v`, each curve a sketch curve id, a
{sketch?, curves} chain (planar or 3D), a {body, edges, continuity?}
edge chain (g1/g2 with the face beside it) or a {point} for a
three-sided patch, with `operation` new or join. Edits may move between
the two forms (timeline.redefine accepts the command now that it has a
dialog).
Tests: analytic areas of loop patches and of a hyperbolic paraboloid
bounded by four 3D lines (every mesh vertex on z = xy/10), a loft
across two sketches, G1 and G2 measured across a cylinder's edge with
inspect.continuity (angle < 0.1°; curvature jump 1e-16 with G2 against
0.027 with G1), 26 hostile networks refused without panicking, and u/v
added to hostile_params_never_panic.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* feat(ui): Boundary Surface dialog
Curves and Cross curves take sketch curves and edges (picks that meet
end to end in one sketch or body are one chain); Continuity and
Operation (New Body or Join). Two to four sketch curves of one sketch
with nothing across are the loop patch; anything else is a network.
Edit Feature brings either back (per-side orders, crown and stations
the dialog does not show are kept). Strings in en, ja and zh.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* docs: ROADMAP M8 and the bridge patch's notes for boundary networks (#763)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* test(oracle): a boundary surface through a loop, thickened (#763)
Case 83: four sketch curves (a square's three sides and a half circle
for its top) make one boundary surface, thickened 2 mm; analytic values
from tools/oracle-analytic/cases_surfaces.py (V = 2A, area 2A + 2P,
centroid by moments). Recipes gain boundary_surface, thicken and remove.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* refactor: boundary surfaces, review cleanups
Project onto the face once per derivative evaluation (the frame is
passed to natural() and reused by scale()), keep each track's
finite-difference step instead of rescanning its table, export the
kernel's edge-pick and chain caps and the default station count for
the engine, doc and dialog to share, map TooLarge spline errors to
KernelError::TooLarge, reuse the engine's operation parser, and skip
the dialog's sketch lookup when the picks are no loop.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
The continuity core (kernel bridge: Hermite control rows reproducing a support surface's position, tangent, curvature and change of curvature, G0 to G3), surface.blend between two edge chains (#764), and a crown for fitted patches. Existing patches and fillets are unchanged by default (crown 0 is the plain patch bit for bit). SurfaceBlend and Patch.crown are noted under format 22.
New command inspect.compare {a, b, tolerance?}: measures of both and their differences, two-way surface deviation from a bounding-volume tree, regions beyond the tolerance clustered by side (only_in_a / only_in_b) with integrated volumes and faces, a verdict, optional face colouring as one undo step, and warnings for open meshes. Geometry in solidcraft-geom (compare.rs), command in the engine. Closes#1363.
Packs the scene's planned bodies into one GPU upload and dispatch, and evaluates intersection edges by seeded Newton refinement from a fitted B-spline through exactly solved leader points, falling back to the previous evaluation near tangency. Intersection nodes carry their faces' parameters. This changes speed, not what the app draws.
Part 4 of 4 of #303.
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
A design with components and joints exports as a URDF robot description (file.export to .urdf, the MCP export tool, solidcraft-cli run --out, File > Export URDF...). It writes one binary STL per component in metres, links with mass, centre of mass and inertia from material density, and maps rigid, revolute, slider, cylindrical, pin-slot, planar and ball joints to URDF joints or short chains. Loops, broken joints and loose parts are reported as warnings. Options: mesh_prefix, effort, velocity. Docs in docs/urdf.md.
find_close_pair's budget now counts the grid's own work too (each cell a triangle is filed under or visits), not only the pair tests, so a pathological pair of meshes can't spend unbounded time building and walking the grid. Adds tests for find_close_pair and the budget.
When an extrude cuts with profiles whose outlines stay more than 1 µm apart (the letters of a text), their tools are apart too, so they are joined and cut from the body in one boolean instead of one per profile. A ten-letter text cut drops from about 13 s to 1.5 s with the same result. Sheet metal targets and touching profiles keep cutting tool by tool. Tapered extrudes are unaffected.
Sheet-metal cut-outs and base flange outlines drawn with ellipses, splines or text stay exact curves in the flat pattern and the unfolded body; the folded body follows them with tangent arcs within 0.001 mm (#659).
A SolidCraft-owned portable B-rep schema (geometry schema 2 with analytic curves and surfaces, explicit frames and ranges, fitted intersection curves) and a versioned body envelope (SCBREP03) with its own metadata records, a bounded binary codec, a validator with resource budgets, and an adapter that refuses what it can't convert exactly. Pinned by a box-and-fillet golden fixture. Not yet written by application saves. Refs #303.
When sample points say two bodies are apart or one is inside the other, the facetings are now checked for surfaces passing through each other; if they do, the boolean is computed instead of shortcut. If it still can't be intersected, the sampled answer is kept as a flagged, unverified result, and Interference lists such pairs as "could not be checked" with the reason. Fixes#442 and #443.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Add a one-surface fill of closed 3D loops to geom
A closed loop of curves that does not lie in a plane has no exact surface;
the usual answer is one smooth face fitted over it. fill_loop does that:
- the loop's best-fit plane (Newell normal), with a frame chosen from the
loop itself so the result does not depend on where the loop starts, its
direction, or where the part sits
- the loop seen along that normal must be simple and must not fold or run
along the normal; otherwise it is refused ("not supported yet"), never
filled with wrong geometry
- one non-rational bicubic B-spline height field over the loop's box,
fitted by least squares to the loop's samples (The NURBS Book 9.4.1,
9.4.3, eq. 9.62/9.65) with a thin-plate smoothness term
lambda*A*int(h_uu^2 + 2 h_uv^2 + h_vv^2), A one grid cell's area, so the
fit is the same at any scale; only planes are reproduced exactly
- span counts per direction (long narrow loops fit), refined until the
loop is within tolerance, else refused with the deviation reached
bspline: bisected span search, basis functions on a stack array, one
clamping helper shared by curves and surfaces, one binomial helper.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01J53sR6gEaVt56soFDpTck8
* Patch fills non-planar loops of edges with one smooth face (#250)
surface.patch with edges refused any loop that is not planar ("not
supported yet: patching a loop that is not planar"). It now fills it:
- planar loops still get one exact planar face, but planarity is certified
conservatively: lines by their ends, B-spline/NURBS edges by their control
points, intersection curves by their samples lying on a support plane
within tolerance; a loop that can't be certified is filled instead
- other loops get one face from geom's fill_loop, bounded by the body's own
chained edges, whole (no split): its history is one generated face whose
edges are the body's, and it stitches back into a closed solid
- intersection-curve edges are sampled by a seeded, guarded double
projection shared by the planarity test and the fill (plane_fit)
- the face tolerance is 10x the planarity tolerance (documented: later
operations take the face to contain its edges within it)
- edge picking runs inside the guard; the geom->truck conversion is shared
with the T-spline sheets (spline_conv); the Newell plane fit is shared with
STEP import
Tests: 3- to 8-sided, concave (dart, arrow, plus), flat-corner, two-edge and
imported rims fill as one face and stitch closed (volumes against an
independent integral); finite mesh normals, same result for any pick order
or placement; non-height-field loops and too-fine detail are refused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01J53sR6gEaVt56soFDpTck8
* Test the Patch dialog filling a non-planar loop of picked edges
The Patch dialog's only test used a sketch profile. Picking the four
curved rim edges of a box cut by a sideways cylinder now makes one
surface.patch command whose result is a single smooth face over the rim.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01J53sR6gEaVt56soFDpTck8
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
fill_triangles bounded the slab triangulator by edges x slabs, as if every
edge crossed every slab. A ring sampled finely at a close zoom has hundreds
of edges and slabs but only four edges in each slab, so the estimate ran a
hundred times over the hover highlight's budget and the fill was dropped,
leaving only the outline. Count the slabs each edge actually spans instead.
Region2::triangulate tested every edge against every slab, so its work was
the overestimate. It now sweeps upward with the edges crossing the current
slab, giving the same triangles in time proportional to them.
Fixes#164
Co-authored-by: Vitali M. <6042958+vitalibr@users.noreply.github.com>
* Add B-spline basis, knot insertion and NURBS surfaces to geom
Freeform faces need local refinement and gap-free joins between patches
with different knot vectors, which tensor B-spline grids cannot give;
T-splines can, and the first user is an N-sided Boundary Fill of
non-planar loops. This lays the univariate groundwork they rest on, in
the L0 geometry crate so it stays independent of the B-rep kernel:
- Cox-de Boor basis of one function from its local knot vector, on
half-open spans with a left-limit side for the domain end, with
derivatives (NURBS Book eq. 2.5, 2.9)
- knot insertion into a single basis function (Sederberg et al. 2004
section 3) and Bezier extraction of one function by repeated insertion
- Boehm knot insertion for curves (NURBS Book A5.1), de Casteljau
evaluation and sub-segments
- a rational tensor NURBS surface with evaluation, knot insertion and
clamping, and a rational Bezier patch type
All input is checked (finite, monotone knots, positive weights, size
caps) and returns SplineError; nothing indexes unchecked.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01J53sR6gEaVt56soFDpTck8
* Add T-spline surfaces: T-mesh, evaluation, AS check, refinement, extraction
Tensor B-spline faces refine only by whole rows and columns and cannot
join patches with different knot vectors without gaps. T-splines allow
T-junctions in the control net, which fixes both; the first user is an
N-sided Boundary Fill. This adds the maths only (no command, no change
in behaviour):
- T-mesh in index space with knot values per line, validated (outer
rectangle, rectangular faces, no empty lines, size caps); local knot
vectors read off rays from each vertex, rays leaving the mesh repeat
the boundary (Sederberg et al. 2003 section 3)
- rational T-spline evaluation and first derivatives for odd bi-degree,
with a complete (p-1)/2-line frame and the domain inside it
- T-junction extensions and the analysis-suitability check (Scott et al.
2012 section 2)
- local refinement that keeps the surface exactly: requested knot lines
are cut in, then every original blending function is carried as a
record and split (violation 1) or the mesh gains edges (violations 2
and 3) until each record is a blending function of the refined mesh
(Sederberg et al. 2004 section 3); analysis-suitable input stays
analysis-suitable by carrying conflicting T-junctions across faces
- NURBS <-> T-spline conversion for meshes without T-junctions, and
Bezier extraction over the rectangles no blending-function knot line
crosses
Measured: regular T-spline vs NURBS < 1e-12, round trip exact, partition
of unity with T-junctions < 1e-14, refinement deviation <= 1.4e-14 over
40 random refinements, Bezier patches vs surface < 1e-14.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01J53sR6gEaVt56soFDpTck8
* Convert T-splines to sewn NURBS sheet bodies in the kernel
A T-spline is only useful to the modeller once it is a B-rep face set.
tspline_sheet builds an open shell: a mesh without T-junctions becomes
one clamped NURBS face; otherwise each Bezier element is a face, and
sides are split at the T-points where neighbours' corners land, so all
faces share vertices and edges and the sheet is one oriented shell
(V - E + F = 1). Every truck call runs under guard. No command yet;
Boundary Fill will be the first caller.
Tests: one face for a regular surface, sewn Bezier faces with
T-junctions, tessellated points on the surface to ~1e-9 mm, and hostile
control nets (coincident, 1e300, needle-thin) never panic.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01J53sR6gEaVt56soFDpTck8
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Extrude, revolve (partial and full turn), tapered extrude, loft (incl. to a
point), sweep, path sweep, coil, primitives, lip, emboss and thicken attach
the exact history of the bodies they build: each face's profile segment, cap
or operand face, and each edge's operand edge, recorded by topology identity
inside the building call. Nothing is sampled; a body whose faces do not follow
the expected construction carries no history. Face sources are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01J53sR6gEaVt56soFDpTck8
Group kernel pieces across circular rims and hidden surface seams for hovering, selection, dialogs, and measurement. Preserve physical references and cover full-item toggling and picking with regression tests.
Fixes#88
The kernel moved from monstertruck to truck: truck's booleans handle blind
holes, pockets and bosses that monstertruck's did not (see the ADR). Fillets
and chamfers on straight convex edges between planar faces are our own exact
local B-rep operation. The document holds parameters with unit-aware
expressions and a timeline that re-evaluates incrementally.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>