* Thread: turn a shaft thicker than a modelled thread down to its major diameter
A modelled external thread on a shaft thicker than the thread no longer refuses: the shaft
is turned down to the major diameter over the threaded length (run past a free end of the
face), then the thread is cut as before. The turned face is named F<n>:turned and the step
it leaves F<n>:shoulder:start/end. A shaft the part goes on around is refused rather than
cut into, shafts under the minor diameter and cosmetic threads on thicker shafts are still
refused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Thread preview test: an 8 mm shaft is turned down for M6; M10 still refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Face names: pieces of a split face keep their numbers across evaluations (#3902)
Pieces sharing a name were numbered in the kernel's order, or by the index of the operand face
they came from. A boolean can list its result's faces in another order on the next evaluation,
and an operand made by one (a closed sweep tool) carries that order into the indices, so the
#1/#2 of a split face could swap between two evaluations of the same design. Pieces that
nothing else tells apart are now numbered along the spread of their centres (as edge pieces
already were), and pieces from different faces of one operand by kind, then by place.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Face names: older designs keep the piece numbers they were saved with
Numbering pieces by place renumbers split faces in many existing designs, and a stored name
matched exactly would then land on the other piece. Features of a design saved before this
change are marked `kernel_piece_order` by a pending format step and number their pieces as
before; features added afterwards number by place.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
An agent's design changes over the control channel (engine.execute, engine.batch) are evaluated
ahead on a copy of the session on an `agent` worker, then run on the window thread reusing every
feature computed there (doc::KeptResults, whatever the bounded evaluation cache dropped); the
worker also makes the display meshes of the bodies they end with. Exports run on a copy. While a
change computes, or the agent cursor acts one out, ui.*, inspection and screenshots answer; later
design changes wait their turn. A chip names the command with Stop. A person's edit meanwhile goes
first; a replaced design refuses the request. Preference: Preferences > AI, agent_off_thread, off
by default.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #2966
* Expressions: a leading decimal comma such as ,5 is accepted (#2966)
In a comma-decimal locale `,5` means 0,5, but the lexer only started a
number on a digit or a point. A comma now starts a number outside
parentheses when a digit follows and an operand is expected (at the
start or after + - * / ^). Commas after an operand keep their meaning,
so function arguments and the existing error cases are unchanged.
* claim: #2882
* Holes from a sketch on a body's face drill that body (#2882)
A multi-point hole from a sketch attached to a body's face chose its
side and moved its points onto whichever body lay along the direction,
then cut every body, so points on a front body's face could drill the
body behind it. `targets` was accepted and ignored.
- solid.hole: holes at the points of a sketch on a body's face store
that body as their participant (the lookup a face-sketch Join uses);
`targets` sets the bodies to drill, `["*"]` every body; explicit
participants still override.
- Evaluation: for sketch-point holes with participants, the drilling
side, the surface each point moves onto and pattern copies are found
on those bodies only.
Sketches on planes, position and Single holes, and saved holes without
participants recompute as before; no design-format change.
A sketch attached to a face is evaluated in the face's frame. When that frame is the body's
own, the body was still rebuilt as a new ModelBody with empty mesh cells, so projecting the
face's edges display-meshed a throwaway copy and the next cut or join meshed the same body a
second time. On a body whose cut edges are slow to mesh this added about a second to each
feature after a sketch on a face. In place, the anchored body is now the model's own clone and
shares its mesh.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #3510
* Split Body: each piece can be renamed on its own (#3510)
A split named its new pieces after the split body every time (`Top (1)`),
so renaming a piece did nothing, and renaming the split body renamed the
other piece too (and broke the features that used it). The pieces now
take the names body.rename stores, and a rename keeps the names later
features derive from the renamed body.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Phanoob <phanoob@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #3383
* Combine: tools from another component meet the target where they are shown (#3383)
Bodies are evaluated in their own component's frame and an occurrence's
placement is applied only for display. Combine passed tool bodies to the
boolean untouched, so a tool in a component placed differently from the
target's was read as if its coordinates were in the target's frame: a
join that overlapped on screen gave two separate shells, and cuts and
intersects missed the same way. Any placement difference did it, a turn
or a plain move, in either direction.
Combine now moves each tool by the inverse of the target's placement
times the tool's own, the same placement used to show the body, keeping
face lineage. A tool placed exactly like the target is left untouched,
so combines within one component give the same result as before.
Moving an occurrence now re-evaluates a combine that depends on it.
* Joins, cuts and intersects draw their tools where they are shown (#3383)
A primitive, extrude, revolve, loft, sweep, pipe or coil that joins,
cuts or intersects bodies draws its tool in its own component's frame,
but each body is kept in its own component's. A target in a component
placed differently (an occurrence moved or turned, or a body moved into
it) met the tool as if the tool's coordinates were in the target's
frame: a join that overlapped on screen gave a separate lump 100 mm
away, and cuts missed the same way.
While such a feature evaluates, the tool now goes into each body's frame
(the inverse of the body's placement times the feature's component's)
wherever the join, cut or intersect meets it, and a body joined into one
placed differently is moved into its frame. Bodies placed as the feature
is are left untouched, so results within one component are unchanged.
Features that name the bodies they change re-evaluate when an occurrence
moves.
This also settles the moved-fastener cut of #439 (Combine, earlier commit).
* Through all and an extrude's contact tests see targets where they are shown (#3383)
An extrude or revolve measured its through-all length, and tested where
its tools meet the targets (a profile on a target's face, coplanar
growth, holes over empty space, taper run-on), on the targets as stored
in their own component's frame. With the tool now moved into a target
placed differently, a through-all cut drawn from the root under a cube
in a component moved 100 mm up was cut only as far as the cube is tall
in its own frame, and missed it.
These features now see the bodies they change that are placed
differently moved into their own component's frame, the same moves the
tools are taken back through, so the length reaches the target where it
is shown. Bodies placed as the feature is are read as before.
* claim: #3353
* Sheet metal: mirrored and copied sheet bodies stay sheet metal
Mirroring a sheet metal body into a new body gave a plain solid: the
opposite-hand bracket had no flat pattern, DXF or bend table
("`Body1 (2)` is not a sheet metal body"). Copies from a body pattern or
Move with copy lost their sheet model the same way.
A copy now takes the sheet model with it (SheetBody::copied). A rigid
copy moves the flat frame. A mirror moves the frame with its x axis
turned round, so the thickness side stays, and mirrors everything in
flat coordinates (x -> -x): base, flange bend lines (run from their far
end, with their end extensions, slopes and tears swapped), panel shapes,
cut-outs, pockets, bores, letters and base sketch lines. Arcs stay exact
and loops keep their sense. A perforation field of a mirrored copy runs
its grid from the right, so its holes are the mirror image too. The flat
length, bends and K-factor are unchanged, and the copy takes further
sheet metal features of its own.
Mirror with combine is unchanged: the joined body has no single sheet
model yet. Mirroring or patterning flange features is still refused.
Sheet models are derived from the timeline, so no design format change.
* Format: note the saved from_right of a mirrored sheet's perforation field
The new `from_right` flag is saved in the design, so it gets a pending
format note. No migration: a field without it runs from the left as
before.
* Extrude: a join from a whole face rounded by fillets sweeps the face itself (#2040)
A face's sketch fits an edge that is no line or arc (the quarter-ellipses
where fillets meet a slanted face) as splines a hair off the body's edges,
so a join from the face touched the body along a face it did not match and
failed with "boolean Union: no result" after minutes. When the profile is
a whole planar face of the one target, the join now sweeps the body's own
face, which shares its edges and is sewn on along it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Extrude: a cut into a whole face keeps the walls that cut and moves the others off (#2040)
A cut from a whole planar face sweeps walls from each of its edges. Where
the face beside an edge turns away from the sweep (n_N . -n_P >= 0) the wall
only touches the body along that edge, or lies in the face beside it, and
the boolean failed on it with "no result". The cut now keeps the walls that
go into the body, exactly (the body's own edges), runs the outline round
the others well outside the body, and starts a little out from the face.
A cut whose walls all only touch takes a slab beyond its depth plane.
Not covered: a cutting wall tangent to the face beside a touching one (a
round's wall meeting an end face, as in the issue's part); the boolean
still fails there.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Extrude: leave a whole face outlined by lines and arcs to the profile's own tool
Only a face whose outline the projection had to fit needs the body's own face as the tool. A square drawn over a box's top already meets the body exactly, and the swept face lost the names a sketch on the new top attaches to (stacked_face_tests, #489).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Run the whole cut tool from a face under the kernel guard (#2040)
Review: `builder::vertex`, `builder::line`, `Face::try_new` and
`builder::translated` ran outside `crate::guard`; only the sweep was
guarded. `cut_tool` now runs all of it under one guard.
Adds an end-to-end test of a cut into a face the body stands out past
below it (the block's top strip between its rounds): it takes only
what lies over the face.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* test: the slab cut of whole_face_tool, on a spline prism (#2040)
A prism on a closed spline standing on a wider plate, cut 3 into its whole
top face: the slab takes the face's area times the depth and leaves the
plate alone. A test-only counter asserts the slab was the tool, so the test
cannot pass through the profile's own tool. Shortens the name of the
rounded block's top-face cut test.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Kernel: the face's outline as a Vec now that polyline returns a closed chain (#2040)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #3378
* Pattern and mirror copies of a join that merged its targets join the merged body (#3378)
Since #2755 a pattern or mirror copy of a primitive reuses the seed's targets. When the
seed was a join that merged two targets, the second one no longer exists, so the copies
failed with `unknown body`. The copies now keep the seed targets that are still there;
when none is, the names stay and the error says which body is missing.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Rerun CI: the previous run was cancelled before any check ran
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The first hover over a large body made two things in the frame: the body's
pick index (its triangles and edges in hierarchies; about 0.3 s for a long
modelled thread, a quarter of a million triangles) and, with the GPU viewport,
the plan mesh a highlighted face is drawn from (about 0.7 s for the same
thread). The window froze for the sum.
A large mesh's pick index is now made on a worker, and picks scan the mesh
until it is there (a few milliseconds); a body's plan mesh is made on a worker
too (`ModelBody::plan_mesh_soon`), and until it is there the hovered face is
lit on the mesh the viewport already has. Small meshes, and the browser build,
make both at once as before.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* perf: renaming a feature evaluates nothing (#3044)
A feature's name labels it and builds nothing, but a timeline rename evaluated
the whole design again (about 70 s on the Prusa Core One assembly, and again
for undo). When the only change is one feature's name, the model renames its
result, sketch and construction geometry in place and takes the renamed
design's fingerprints. A rename other features follow (a plane a sketch is on)
or of a failed feature still evaluates the design.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Guard cheap commands on designs with thousands of bodies, plus a scaling bench (#3044) (#3121)
Cheap commands stay cheap on designs with thousands of bodies, with a scaling bench.
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
A closed loop whose joints meet a few nanometres apart along their parallel
axes (faces modelled that far apart) passes the conflict check, but the loop
solver wanted 1e-7 mm before it moved anything. No value of a planar loop
takes such a gap out, so every drive of it stopped at once (stopped_by_loop,
fraction 0) and joint.reach called the loop open.
The solver now closes such a loop as far as it comes and, when what is left
is within the conflict check, keeps it that closed on the way. joint.drive,
joint.reach and the nearby pose of the dof count share it.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
A body rename changes names only, but committing it went through the general
"design changed" path: the whole timeline was evaluated again. On an imported
assembly that means reading the STEP file again and meshing every body (about
100 s on the Prusa Core One, and the same again for undo).
When the only change from the previous design is one body rename (the
features' stored body names and the body-keyed maps the rename updates), the
model now renames the body in its results instead: every body keeps its
geometry and meshes, and the fingerprints are set to the renamed design's so
the next evaluation reuses everything. Undo and redo of the rename take the
same path. A rename the model can't follow that way (the body is changed or
named by a later feature, sheet metal, threads) still evaluates the design as
before.
`bench-open --ops script.json` times commands and their undo on an opened
design, with the view work each leaves.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* WIP: adopt the saved model on open (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* WIP: tests
* WIP: bench-open opens as Open does
* docs: opening from the saved model
* Tests: an edit after opening evaluates from the feature it changes
* clippy
* Read SOLIDCRAFT_NO_MODEL_CACHE through the env helper
* Open: no picture from the model when the model itself opens; cancel test evaluates
* Saved model: bodies passed through found without writing their record; states list runs of bodies
* Adopted results go into the evaluation cache: an undone edit, or the marker rolled forward, takes them again
* Model cache size guard: the saved model's writer
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #3234
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Sheet metal: refuse an edge flange on a flange's bend line (#3234)
A pick on the edge where a bend meets the plate (or the flange panel)
found a panel edge that is already a bend line and made a second flange
on it, leaving a gap and a sheet of two shells. add_flanges_each now
refuses such an edge before anything moves.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
* Open: show the design as its bodies are meshed, off the UI thread (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Open: hold screenshots until the design is meshed; profile lines
* Tests: time-bounded opens
* Open: a Loading parts n/N note while bodies are meshed
* Open: frame the design from outlines while it goes into the window
* Outline bounds: vertices and edges only; test
* Frame watch: the window thread's frame times by open phase (SOLIDCRAFT_PROFILE_FRAMES)
* Open: the picture grows in mesh order and stays once complete; refreshes pace themselves; named frame steps; watchdog test
* Open: outlines measured on the file worker and kept per body
* Open: draw the Home picture under the opened file's own key once meshed
* Format the open wait
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #3324
* Sheet metal: refuse a flat pattern that no longer matches the body
A feature that is not sheet metal can change a sheet body's material
without its sheet model knowing: a mirror combined into it, an extrude
joined onto it, a fillet or chamfer on a corner. The flat pattern, the
DXF and the bend table then wrote the sheet as it was before, a part
other than the one in the design, with no warning.
The evaluator now notes, per sheet, the first such feature: one that
changes the body's shape while its sheet model stays the same. That
feature warns, and sheet.flat_pattern, sheet.export_dxf (also with
per_body) and sheet.export_bend_table refuse with "not supported yet",
naming it. A sheet metal feature, or machining the sheet keeps as
cut-outs, rebuilds the body from the model: it clears the note and
warns that the change is not kept. Moving the body, splitting its faces
and cosmetic threads leave the flat pattern as it is.
* Sheet metal: a modelled thread is refused in the flat pattern too
Only a cosmetic thread leaves a sheet body's material as it is. A
modelled thread cuts the thread profile into the hole, which the flat
pattern does not have, and a later sheet metal feature dropped it
without a word. It now marks the sheet like a fillet does: it warns,
the flat pattern, DXF and bend table refuse naming it, and the feature
that rebuilds the body says the thread is not kept.
`PlaneRef::walk_exprs` stopped at `Flipped`, so a sketch created with
`flip` on an offset plane (`{plane: "XZ", offset: "d", flip: "x"}`) did
not list the offset as an input. Changing `d` rebuilt nothing that read
the sketch, and the model went stale.
`Flipped` now continues to its base, as `Offset` and `AtAngle` do, in
both `walk_exprs` and `walk_exprs_mut`.
Test: a loft between XZ and a flipped XZ plane offset by `d` has the
volume for d = 30, and for d = 50 after `parameters.change`.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: Convert to Sheet Metal keeps a plate where it is
* Convert to Sheet Metal keeps a plate where it is
Converted without bend edges, a plate moved by one thickness: a 100 x 60 x 2
plate on XY came out at z -2..0 picked on its top face, 2..4 picked on its
bottom. The sheet's frame (its base panel's bottom face, thickness along its
normal) was put on the plate's far face facing away from the picked face, so
the material grew out into empty space.
The frame now lies on the picked face with z into the material, as Convert
with bend edges does. The sheet is the old one moved back by the thickness:
same orientation, flat pattern, flange directions and pocket layers.
A test converts the plate from either face and checks its bounding box; the
engraved-plate test now checks the plate's position, not only its thickness.
The two reliefs that would overlap are still resolved one after the other: the
second one is left out, with a note. The corners come out in flange-index
order, so which of the two keeps its relief depends on the order the flanges
were made in.
Two corners that share an edge never come this far: each relief reaches
exactly r along that edge, and a relief is refused unless 2r fits in it. Two
corners that do not share one can: the square relief at a corner of 120°
reaches 2r from it along the bisector, so at the two 120° corners opposite
each other in a rhombus the two reach each other.
Two reliefs that would overlap are now left out together, each with a note
naming the other, so that which of them is cut does not depend on the order
the flanges were made in.
Fixes#3417.
Co-authored-by: jeremymiribung-blip <jeremymiribung-blip@users.noreply.github.com>
Co-authored-by: Claude Code <noreply@anthropic.com>
Moving an occurrence places every body under it again, and each placed copy
searched every revolved face for where it sits to turn it away from its seam,
although its source had been turned already. On the Prusa Core One assembly
that search was most of the 12.7 s a move of the top occurrence took. A body
now records that its revolved faces are turned, and world placement
(`place_matrix`) skips the search for such a body. Modelling moves (pattern
copies, hole tools) keep `transform_matrix`, which still turns them in the
copy's own frame: where a face wraps all the way round the turn it finds
depends on those coordinates, and later booleans depend on it.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* kernel: a blend runs along chains of several faces and lines closed rims up (#764)
A blend's chain may run along the boundaries of several faces (a tube's rim
along the halves of its wall): each edge continues from its own best-facing
face, read station by station. Before, a chain had to be the edges of one face,
so every rim of a revolved or cylindrical surface was refused.
Two closed chains blend from matching seams: the second chain's start (searched
by arclength, then narrowed) and direction are the ones that put each station
closest to its partner, so rims whose seams sit apart no longer twist. A
picked `seam` point on each chain fixes the start instead. A closed chain
against an open one is refused. Closed chains leave towards each other's
centroid, not a point on the rim.
Stations are read on the edges' own curves, not on the chords of the length
table (they sat up to the chord's sagitta inside a curved edge), and the
reported gap is measured to the curves.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* kernel: closed blend chains run round the same way; Hermite strip and seam tests (#764)
The second of two closed chains runs round the same way as the first (by
their area vectors), so a picked seam turns the blend by just the angle
between the seams instead of folding it over. The nearer pairing decides only
when the loops stand almost at right angles.
Tests for the issue's gates: the blend between two offset box rims is the
analytic cubic Hermite strip (control points from the chord) and keeps the
top faces' normal along both seams; picked seams a quarter apart turn the
blend a quarter round.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* surface.blend: `seam` picks where each chain's stations start (#764)
A point on each chain, saved with the feature (one pending format change),
moved with the design like `align`, and refused when it is not two points.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* surface.blend: a test between two tube rims, their seams picked and saved (#764)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* Blend dialog: edges at each end, continuity and bulge per end, stitch (#764)
SURFACE › CREATE › Blend Surface opens a dialog: the edges the blend leaves
and the ones it arrives at, each end's continuity (G0–G3) and bulge, and
Stitch to both bodies. Edit Feature brings it back and keeps what the dialog
does not show (align and seam points). Labels in every locale catalog.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* ROADMAP: M8 Blend runs along several faces, pairs closed rims and has a dialog (#764)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* kernel: a blend station on the vertex between two support faces is read on the neighbour (#764)
A station where a tube wall's two halves meet sits at a corner of one half's
parameters; with a leave direction that turns round the wall (tubes off each
other's axis) the shape could not be read there and the blend was refused. The
neighbouring chain edge's face holds the same point and reads it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* blend: review clean-ups (#764)
- ChainLine keeps one list of samples instead of four parallel lists.
- frames_on and boundary_gap take the chain's ChainLine instead of rebuilding it.
- A station is read on the neighbouring face only when it sits on the vertex the two edges
share, each face once, and each face keeps its own walk.
- The seam rule (a closed chain starts at it, an open one runs from the nearer end) lives in
ChainLine::start_at_seam; pair_with reuses the start of its both-ways search.
- support_faces projects with curveblend::project; loop_area sits with plane_through.
- surface.blend parses `align` and `seam` through one point_pair; the Blend and Ruled dialogs
share body_and_edges.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Iterate instead of indexing in nine loops
Replace index loops that look up neighbours by position with enumerate,
zip(cycle().skip(1)) for wrap-around pairs and zip(skip(1)) for
consecutive pairs. No behaviour change.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: ring_edges for the edges of a closed ring
Every walk over a polygon's edges, the last back to the first, spelled
x.iter().zip(x.iter().cycle().skip(1)); eighteen of them now call
geom::ring_edges. Three redundant take(len) calls go with them.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Ring, a closed ring that knows it is closed
A Ring holds items in order around a closed polygon, loop or fan; edges()
walks each with the next and the last with the first, corners() each
with both neighbours. Ring<Vec2> has signed_area and even-odd contains.
Loop2::polyline returns a Ring, as do doc's face_loops and
boundary_loops, kernel's coplanar wire samples, CapLoop's segments,
tess pieces' rings, the gizmo's plane quads and the navigation cube's
facets. Their walks take edges() or corners() instead of wrapping an
index; sketch's text-hole test and doc's poly_area become contains and
signed_area. Loop2::joints pairs each segment with the next.
Replaces the ring_edges free function.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Chain, Ring and Path; bounds for a chain of points
Ring becomes Chain<T, Closed> beside Path = Chain<T, Open>: edges()
closes a ring and stops at a path's end, Path::close makes the ring,
and bounds() (the empty box for no points) serves both. Eight
hand-rolled min/max folds over a loop's polyline call bounds(); doc's
flat_polyline returns a Ring.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: area and inside on Ring for any planar point
Ring's signed_area and contains take any Planar point (Vec2 or
[f64; 2]). The cam profile in joints_cam is a Ring: its own even-odd
test goes, and its edge walks, gap and area take edges(). face_params'
loop area, the text path's winding, tess pieces' ring area and the
copies in three tests call signed_area or contains; the formulas are
the same term for term.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* doc: sheet's closed outlines go through Ring
dedup takes and returns a Ring (dropping a last point back on the first
is what makes it a ring's), near_outline walks a Ring's edges, and the
copy of it beside fold checks calls it. point_in goes: its callers ask
the Ring. Its formula anchored each crossing on the other end of the
edge, so the two can differ only for a point on an edge to the last
digit; one caller sets such points aside first, the others test a
region's interior point, a cut's midpoint or another outline's corners.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* doc: cam tests build their outlines with Ring::from
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: area_vector on Ring<Vec3>; three Newell sums use it
Ring<Vec3>::area_vector is half the sum of a × b round the ring. heal's
loop_area, lip's outer-loop turning and the revolve's loop orientation
summed it by hand with a wrapped index; they take it from the Ring
(the half is exact, and two of them only read its sign).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Aabb3 from points; boxes built and asked through it
Aabb3 collects from points (skipping non-finite ones, as add does) and
gains inflated, contains and meets. Fifteen hand-rolled min/max folds
over points or boxes in kernel, doc and engine become collect or union,
and their "within tol of the box" tests become inflated(tol).contains.
blend's refused-edge boxes and naming's face index hold an Aabb3.
A NaN point is now outside every box, where the old negated
comparisons let it in; an infinite point no longer stretches a box.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Aabb2, the plane's box; 2D folds and box tuples use it
Aabb2 mirrors Aabb3 (collect, add, union, inflated, contains, meets)
and adds relative, a point's place in the box. sketch's link and
link_loops each had that formula; link_loops' boundaries, prism's
segment and loop boxes, profiles' shape boxes and grid, and ends'
segment box hold an Aabb2 instead of a (low, high) pair. Folds in the
cam, sketch bounds, sheet's perforation grid and the sketch clipboard
collect one.
Boxes are built from the same terms (a round's box keeps c - r - tol).
As with Aabb3, a NaN point is outside every box and an infinite point
no longer stretches one.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* kernel: prism's segment boxes are plain Aabb2s
The SegBox alias named a (low, high) pair; Aabb2 says it itself.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Chain::bounds is an Aabb2; the boxes #2382 left as pairs follow
Chain::bounds returns an Aabb2. Its callers keep it: sheet's hole and
cut boxes (loop_box), letter boxes, island outlines and line-near-cut
test use meets, contains and inflated; profile's outline overlap and
max_clearance, profiles' box tests and the cam test read its corners.
flat_size and the flat pattern's JSON size are the union of the loops'
boxes (0 × 0 for no loop, where the pair fold gave -∞).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: Aabb3::intersection; hand-grown and hand-met boxes use the box
Aabb3::intersection is the box both hold. ops' four overlap boxes of a
boolean's operands take it, and seven boxes grown by hand (ops' body
boxes, the distance set's bounds, coplanar's face box, eval_more's
padded mesh box, compare's group and region boxes) call inflated with
the same amount on every side.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
A line and a circle or arc can now be dimensioned to the circle's edge
(ConstraintKind::LineCircleDistance, saved as line_circle_distance): the gap
while the line misses the circle (0 is tangency), or how far the edge reaches
past the line when it cuts through (stored as `inside`).
Rebased onto main as one commit (the branch's own changes; its merges of main
dropped). Conflicts resolved: the test mod lines in cmd/sketch.rs (both kept,
sorted), and README.md, whose feature list main moved to docs/capabilities.md;
the line-to-circle dimension is listed there now.
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
Co-authored-by: jyviko <jyviko@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* kernel: loft guide rails (#201)
A loft follows one or two guide rails between its sections: stations are added between each two
sections, each the plain loft there moved so that the point a rail guides lands where the rail
crosses the station's plane — turned about the loft's direction and scaled (or stretched across
to the rail) with one rail, carried, turned and sized between two. The sections and caps stay
exact; the smooth loft runs through sections and stations. Solid and sheet lofts.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* doc, engine: solid.loft and surface.loft take guide rails (#201)
`rails` (one or two {sketch, curves}) and `rail_fit` (scale | stretch), stored on Loft and
SurfaceLoft (one pending format note), parsed by the sweep's rail parser (now shared) and built
through the kernel's railed loft. Rails on a loft to a point, or on a surface loft with edge
sections or end continuity, are refused as not supported yet. The rails' sketches are walked as
the feature's references and their components placed like a sweep's.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* ui: Rail, Second Rail and Rail Fit in the Loft and Surface Loft dialogs (#201)
The rail inputs and fit row the sweep dialogs have, shared through dialogs_sweep; Edit Feature
brings the rails back.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* docs(roadmap): loft guide rails (#201)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* loft rails: review clean-ups (#201)
- Sweep and loft rails share one turn-and-size map (`sweep_path::rail_frame`).
- A station's middle and the loft's direction come from one curve through the sections'
middles (exact derivative) instead of two more plain-loft evaluations per station; at most
33 wires, so railed faces stay light.
- Nearest points on a section use `param_on` (kept only where the search comes nearer); the
size uses `Aabb3`; one B-spline builder; anchors keep their nudge.
- The railed and plain lofts share one path in `loft_with_rails` and `loft_sheet_with_rails`.
- The engine leaves the not-yet-supported refusals to the design's evaluation; both lofts start
their rails from the first section's first point.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* loft rails: refuse rails on sections with holes, with a test (#201)
Main's lofts now take sections with holes (#2447); rails shape only the
outlines, so a railed loft of rings is refused until the rails carry the
holes too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Model cache written by default: exact bodies, stored once, scaled caps (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* bench-open: say why bodies were not kept
* Exact planes and revolutions; budgets for large bodies (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Native B-rep: rebuild shells as the kernel made them (closed and seam edges) (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* docs: the model cache and the exact native B-rep (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* bench-open: time a save without the cache too
* Model cache entries are Deflate-compressed (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Model cache: one that does not fit the design file is left out, never a failed save (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Sheet metal: a corner relief no longer depends on the order the corners are cut in
The corner reliefs are planned against the base as it is before any of them is
cut, and the two reliefs at the ends of one edge are compared with each
other. Before, every relief was cut into the base as it went, so the corner
after it saw the relief of the corner before it: the square relief reaches
further from its corner than the round one does (4 / cos(α / 2) against 4), so
on a short edge it was left out where the round one was cut, and which of the
two corners kept its relief depended on the order the flanges were made in.
The reliefs themselves are unchanged: a round about the corner through the
angle the base fills there, or the square with that side (a kite where the
corner is not square, its cuts square to the two edges). What is new is that
they are planned first and cut together, so that a corner's relief depends on
the base and on the other reliefs, and not on the order they are cut in. Two
reliefs that would overlap are still refused, now with a note that says so.
Covered: the four relief shapes at corners of 60° and 120°, with the flanges
of equal and of unequal height, through the kernel and through the engine
(where the flat pattern and the DXF keep one clean loop).
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Sheet metal: cover the corner reliefs at a corner that is not square
The engine and the UI had no test at all for a base whose corners are 60° and
120°: the flat pattern, the DXF, the unfold and the rule manager's own square
relief were all untested there. They work; this says so.
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Sheet metal: say what happens when a corner relief is left out
The guide now says that the reliefs at the corners of one edge are cut
together, and that two of them that would overlap leave the second one out.
A relief that cannot be cut is reported, not dropped.
Co-Authored-By: Claude Code <noreply@anthropic.com>
* Sheet metal: write the corner relief's expected corners out
The engine test hard-coded the corners of the trimmed base; it works them out
instead, and the numbers the test and the sketch share are written with the
precision they need.
Co-Authored-By: Claude Code <noreply@anthropic.com>
---------
Co-authored-by: jeremymiribung-blip <jeremymiribung-blip@users.noreply.github.com>
Co-authored-by: Claude Code <noreply@anthropic.com>
World placement already shares a part's reference mesh between its
occurrences (#2924), but the display plan the GPU viewport draws was made
again for every occurrence from its placed B-rep: planning every face of
every instance of the part. A placement now carries the definition's plan
cells too, and a placed body's plan (and its CPU mesh) is the definition's,
moved by the placement's matrix (`TessPlan::transformed`): the part is
planned once however often it is placed.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Fix large modeled threads and thin crest reconstruction
Helix stations follow the pitch (radial chord error under 1% of it, 48 to
720 stations), and the faceted rebuild retries at the BSP's precision when
the usual weld tolerance collapses a thin crest facet.
Rebased onto main as one commit (the branch's own commits touched UI files
that later moved to #2263 and #2264). Adapted to main's UnitVec3 thread
axis: `*k` in thread_groove and `*cylinder.axis` in the new flange test.
* Fix icon review revisions for same-timestamp edits
An M8 modelled thread in a 6 mm hole, narrower than M8's minor diameter, was
refused as "the face is too far from the thread's diameter". It now says what
is wrong and what fits, as a hole that is too wide already does (#995): "this
6 mm hole is too narrow for a modelled M8 thread (its teeth would fill the
hole); drill 6.75 mm for M8", with the thread that fits this hole when there
is one. A shaft too thick for its thread gets "make the shaft 8 mm for M8".
Fixes#2688
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* Joints: a point origin keeps the x it is given
`joint.origin` and `joint.create` take `x` for a point origin (a
direction, laid square to z) and the point snap saves it. Two origins
given at one point with the same z and x now meet as they are: a part
turned a quarter turn about z no longer turns back (and moves) when
rigid-joined there. A point origin without x takes its x from z alone,
as before. An x along z, or of no length, is refused.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Joint relations test: a point origin has an x too
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01Aac7mP9rthK3WsPpPRvCsF
---------
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
A sketch and the feature built from it may share a name, and the sample and
oracle designs do. `timeline.add` refused such a recorded name, so a design's
own exported script failed to replay. `Document::insert_feature` now keeps the
name, as `add_feature` does; a blank name still gets a fresh one.
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Replace Face rebuilt its body with ModelBody::new and dropped the body's
lineage, so no face of the result was named exactly: a sketch on any face of
it, even one the replacement didn't touch, failed with "this face can't keep
an attachment". Each face it moves is now a lineage step, as in Offset Face
(which does the same geometry), and the result keeps the lineage.
The test of a body without history used Replace Face as its example of an
operation that reports none; it now lifts the block with Align instead, the
same geometry.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* parameters: import evaluates once; parameters.change takes several names
parameters.import checked every row through change_param, which cloned the
design and evaluated every parameter per row: 2000 rows took 9.5 s, 2823 in
an assembly minutes. Rows are now checked and applied in one pass with the
values carried along, then evaluated once (2000 rows: 0.016 s), still all or
nothing; a row may name a parameter defined by a later row.
parameters.change {changes: {name: expression, ...}} sets several existing
parameters together, rebuilt once and undone in one step.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* parameters.change: the params doc names the `changed` result of `changes`
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* inspect.clearance: pairs whose bodies did not change are not measured again
Each clearance check measured every close pair again, though between two
checks usually only a few bodies change or move. Results are now kept per pair,
keyed by both bodies' geometry and placement and the check's settings; a pair
whose two bodies are unchanged is taken from that cache. With 40 overlapping
parts, a check after moving one of them took 0.8 s instead of 23 s (741 of 780
pairs reused). Pairs that could not be worked out are tried again each time.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* inspect.clearance: boxes and placed keys exactly as before the reuse
The pair boxes are taken over the mesh's triangles with finite corners, as a
distance shape's are, so pruning is unchanged. A placed body's identity now
includes its model body's own frame, so two placements are never mistaken for
one another.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* inspect.clearance: a large body is meshed once for all its pairs
Each pair that touches cuts the larger body down to the pair's region with a
kernel boolean, and that boolean meshed the whole body twice: once for its
checks and once inside the intersection. A sheet with 600 faces paid about
2.5 s per pair for meshes that were the same every time.
A body can now keep its meshes for reuse (Body::keeping_meshes); its booleans
take the meshes from there, and the intersection takes its shell meshes
from there too (truck-shapeops: and_with_history_meshed). Clearance uses such
copies for one check. Results are unchanged to the bit. On a 3 x 2 m sheet
with bends and 300 holes, the clip took 0.23 s per pair instead of 2.6 s, and
24 rivets took 5.6 s instead of 16.5 s.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>