Commit Graph
1246 Commits
Author SHA1 Message Date
kaltenbrunnermarkusandClaude Opus 5.5 76e009ab10 Viewport: blend grid levels while zooming instead of popping (#9570) (#9608)
* claim: #9570

* Cross-fade the viewport grid between levels while zooming (#9570)

grid_step switches the spacing in a step (1, 2, 5 times a power of ten), so
the whole grid swapped at once as the view zoomed through a switch and
popped over and over while scrolling. Near a switch the drawn grid now
draws the outgoing and incoming levels together, weighted by a smoothstep
over about 19% of zoom either side, each level's lines on their own places
on the plane so a fading level never shifts. A line both levels share is
drawn once; its colour and width blend between minor and major.

grid_step itself is unchanged, so sketch snapping, dash lengths and the
tools keep their spacing; the dominant drawn level is always grid_step's.
The viewport and the headless picture share grid_lines, so they still draw
the same grid.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Fade out the fine grid before a non-nested coarser level appears (#9570)

The levels go 1, 2, 5 times a power of ten. From 1 to 2 and from 5 to 10
every coarser line is also a finer one, but 5 is not a multiple of 2, so
cross-fading the 2 and 5 levels drew lines at 0, 2, 4, 5, 6, 8, 10 mm at
once, which looked restless.

At that switch the finer level's own lines now fade out over the first
half of the cross-fade and the coarser level's own lines fade in over
the second, so the two are never drawn together. The lines both levels
share (every 10 mm, the finer level's major lines) stay at full strength
throughout, so the grid never goes blank. The cross-fade spans the same
zoom range as before, and the nested switches cross-fade as they did.

grid_levels keeps its shares (adding up to 1, grid_step's level the
stronger one); grid_lines draws a line only one level has as strongly
as that level's own lines. The headless and viewport tests now check
half strength at the nested 5 to 10 switch and no 2 or 5 mm line right
at the 2 to 5 switch; a new test zooms through 2 to 5 in four decades.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 18:35:49 +00:00
froglemonade2andClaude Fable 5.1 441d67f9ff View cube and axis gizmo: a standard view centres and fits the model (#10091) (#10092)
* claim: #10091

* View cube and axis gizmo: a standard view centres and fits the model (#10091)

A new Navigation preference, "Fit the model after a navigator view change"
(`navigator_fit`, off by default): with it on, a face, corner or arrow of
the view cube and an axis tip of the gizmo look at the middle of the model
from the one distance that fits its bounding sphere, so Home, an opened
design and every view chosen on a navigator share one zoom and one centre
and only the direction changes. Off, both navigators turn in place as
before.

"Home and Fit size" (`home_fit_size`, 10–100 %, default 100 %) is how much
of the view between the panels and the controls the model fills when Home,
Fit, an opened design or a navigator view change frames it; 100 % is the
framing as before.

`view.navigate` takes an optional `fit: true` with a direction or a turn,
so programmatic callers get the same framing.

Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>

---------

Co-authored-by: Claude Fable 5.1 <noreply@anthropic.com>
2026-10-31 18:34:13 +00:00
Colin Faulkingham ed66adac5c Keep renamed bodies visible when reusing hidden names (#10163) (#10175)
* claim: #10163

* fix(engine): preserve visibility when renaming into hidden names
2026-10-31 18:15:56 +00:00
Kyle a.k.a. TechSquidTV aeca117045 Sketch: offset chains lines whose corners are coincident (#5019) (#8858)
* claim: #5019

* sketch offset: chain lines whose corners are coincident, not only shared

Lines drawn one by one meet at their own points held by Coincident
constraints. The offset walked shared points only, so each such line was
offset on its own, to the left of the way it was drawn: a closed
rectangle came apart, both horizontals moving up. The same split shows
next to a fillet or chamfer, whose other corners stay Coincident pairs.

Chain ends held by a Coincident constraint as one joint, the way
Sketch::chain() and axis_implied already do, so a closed outline offsets
as one closed shape.

Fixes #5019.

* test(sketch): cover coincident offset loops after trim and blends

* refactor(sketch): share and cache coincident endpoint groups
2026-10-31 17:37:38 +00:00
Dahak BuildsandDahak Builds 31326e9898 Frames: renaming a cut-off piece of a frame member renames a different member after a rebuild (#10123) (#10132)
* claim: #10123

* Frames: a renamed cut-off piece keeps its own name through a rebuild (#10123)

---------

Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
2026-10-31 17:32:32 +00:00
Colin Faulkingham aa244bcee4 Fix copying drawn 3D sketch curves (#10134) (#10146)
* claim: #10134

* fix: copy drawn 3D sketch curves (#10134)
2026-10-31 16:53:47 +00:00
semmelrindeandClaude Opus 5.5 c392791f2c Sketch drag: a step that throws points far from the sketch, or presses a line to no length, counts as failed (#8600)
* Sketch drag: a step that throws points far from the sketch counts as failed

A held step of a drag that moved a point more than 1000 times the sketch's
size plus the drag's way was taken as solved, so a drag could leave points
around 1.4e6 mm away while reporting it reached the cursor. Such a step now
fails like one the solver cannot solve, and the cursor correction refuses it.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Sketch drag: a step that presses a line to no length counts as failed too

An end dragged past the point where its line would have to turn over (a
line held at its midpoint and by an angle, dragged past the midpoint; a
rectangle's corner dragged across the opposite side) pressed the line to no
length, where it has no direction left for its constraints. A step leaving a
line under 1/1000 of its length at the drag's start now fails like one that
throws points far away, so the drag stops just short of it (48 such drags in
4000 random sketches, none with this).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 16:45:35 +00:00
semmelrindeandClaude Opus 5.5 d95b8208b3 Sketch Fillet: a radius of half a side rounds both its corners (#2500) (#8238)
The second fillet of a side whose radius is half its length needs all
that is left of the line, and was refused as too large. Such a fillet
now takes the whole line: the line goes, the arc ends where the line did
and is tangent to the curve that goes on from there. A 20 x 10 rectangle
filleted with r = 5 becomes a slot, a 10 x 10 square a circle. Several
corners in one call keep their arcs by id, as removing a line renumbers
the curves.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 16:15:20 +00:00
semmelrindeandClaude Opus 5.5 99f8cff454 Sketch Fillet: a corner held by Coincident takes a fillet when a dimension measures to it (#7507) (#7778)
* claim: #7507

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Sketch Fillet: a corner held by Coincident takes a fillet when a dimension measures to it (#7507)

Before rounding a corner whose two lines meet only through a
Coincident constraint, Fillet and Chamfer weld the two points into
one, but not when anything else referred to the second line's point,
such as a dimension measuring to the corner: the fillet was then
refused ("the lines must share a corner point"). The point is now
welded as well, and what referred to it refers to the corner, the
same place. A point that a constraint names together with the corner,
or a linked point, is still not welded.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 16:15:04 +00:00
semmelrindeandClaude Opus 5.5 3292cba4ad Sketch Fillet and Chamfer: two lines that share no end are brought to where they meet (#6912, #7759) (#8426)
Two selected lines that stop short of each other or cross were refused
with "the lines must share a corner point". Now each line's end on the
shorter side of their meeting point moves there first (extending a line
that stops short, cutting a line that runs past), and the corner is
rounded or cut as before. Parallel lines, ends held by other geometry
and lines whose length is held are refused and change nothing.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 16:14:40 +00:00
semmelrindeandClaude Opus 5.5 6fa023b3ab Sketch Break: refuse an offset's curves, as Trim and Extend do (#8645)
An offset's ends follow its source curves on every solve, so a break's new
ends were pulled back: a broken offset arc came out in three pieces going
the long way round, and the solve moved curves the break never touched.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 16:14:14 +00:00
lewis2eandClaude Opus 5.5 510378d965 Sketch offset: an offset circle no longer reports a degree of freedom (#9264) (#9573)
The offset sets an offset circle's radius from its source after the solve,
but the solve still counted that radius as a free unknown, so a
dimensioned circle and its offset reported 1 DOF instead of 0. Lines and
arcs were not affected: the offset already holds their end points. The
solve now holds an offset circle's radius too.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 16:12:29 +00:00
PaddleStrokeandClaude Opus 5.5 6a4b5c90c8 Properties: measure faster, show progress, and stop when closed (#8706) (#8730)
* claim: #8706

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Properties: measure faster, show progress, and stop when closed (#8706)

Properties on a large assembly measured every placed copy of every body
afresh (transform plus three fine tessellations each), so it took minutes.
#5203 (in #8103) already moved the measurement beside the window; this
builds on it.

- A rigid placement reuses the body's own cached measurement: volume, area
  and counts unchanged, centre placed, box from the placed corners (quarter
  turns) or from the body's shared mesh placed (other turns). Scaled or
  mirrored placements are still measured as placed.
- Bodies are grouped by component once and the subtree traversal groups
  occurrences by parent once (both were quadratic).
- The measurement beside the window is watched by a Progress: the card
  says "Measuring... n of N bodies" with a bar, and closing it (or
  switching designs) cancels the worker at its next body instead of
  leaving it running.
- component.properties and occurrence.properties are answered on a copy for
  control-channel requests too, as inspect.measure is.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Properties: count the measuring work instead of timing it in the reuse test (#8706)

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 16:04:38 +00:00
Colin Faulkingham 2e981d66e8 Sketch: allow dimension edits with tangent caps (#4823) (#9494)
* claim: #4823

* fix: resize sketches with tangent offset caps (#4823)
2026-10-31 16:04:29 +00:00
froglemonade2andClaude Opus 5.5 0476154973 Update Links: linked designs that changed while the tab was away come back as one undo step (#9743) (#9753)
* claim: #9743

* Update Links: linked designs that changed while the tab was away come back as one undo step (#9743)

Coming back to an assembly's tab read each changed link in an Update Links
run of its own, so each became its own undo step: one Undo took back one
component and left another copy of the same part at the new version.

component.update_links now takes `components`, a list, and goes on past a
design it cannot read: that link keeps its bodies, is named in `failed` and
gets a warning. The tab return sends one request with every changed link,
records as read only the ones that were, and says on the status line which
one could not be read.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 16:04:05 +00:00
Thodoris Tsagkogeorgas 5e265089c7 Sketch: offset corners trim when they cross and extend when they fall short (#10089)
The chain walk follows ends that share a point, a coincident constraint, or
the same position. The offset then meets at the intersection.
2026-10-31 16:03:31 +00:00
semmelrindeandClaude Opus 5.5 31a0c99a2c Delete: the delete runs with what its check computed ahead, instead of building the history again (#9917) (#10090)
* Delete: the delete runs with what its check computed ahead (#9917)

With the history rolled back, a delete builds the history after the
marker to see what it breaks, once in the check that runs off the window
thread (Session::ahead) and once more in the delete itself, on the window
thread. The check's results were lost on the way: the dry run's scratch
session and the whole-history copy dropped what the model keeps, and the
check's kept results never reached the delete. The scratch and the copy
now keep what their model keeps, and the delete (at once or after the
confirmation) runs with the check's kept results, so it finds the
history there instead of building it again.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Delete: test that a confirmed delete runs with what its check kept (#9917)

With the history rolled back, deleting a side of the plate's outline is
checked off the window thread and confirmed first; the confirmation
carries the check's kept results, and the delete adds nothing to them.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 15:19:57 +00:00
semmelrindeandClaude Opus 5.5 59efc86826 Rename Body: a pasted placement's body renames by the name the browser shows (#10017) (#10026)
* Rename Body: a pasted placement's body renames by the name the browser shows (#10017)

The browser lists the bodies of a component's second placement by their
placed names (`KB (K:2)`) and the context menu's Rename sends that name,
but body.rename looked it up only among the model's own bodies and
refused it ("no body"). It now takes a placed copy's name as the body it
shows, as appearance.assign does (#9740): the body is renamed in its
component, so every placement shows the new name.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Rename Body: test renaming a pasted placement's body by its placed name (#10017)

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Rename Body: the test also hides the copy first and undoes the rename (#10017)

A copy hidden by its placed name stays hidden under its new name, and
one undo brings both names back (checks from the review on #10026).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 13:48:14 +00:00
Dahak BuildsandDahak Builds 34c378c063 Save As: rename the design to the new file's name (#4907) (#10036)
* claim: #4907

* Save As: rename the design to the new file's name when its name was borrowed (#4907)

---------

Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
2026-10-31 13:22:10 +00:00
semmelrindeandClaude Opus 5.5 d4eeedbf95 Delete: in a rolled-back history, the check builds the history once when nothing breaks (#9917) (#9972)
* Delete: the check in a rolled-back history builds the history once when nothing breaks (#9917)

With the history rolled back, the check before a delete (which features
the delete would break) built the whole history twice, before and after
the change, with the marker removed. On a large design each build ran
every boolean after the marker: deleting twelve splines took half a
minute on the window thread. Only a feature that fails after the change
can be newly broken, so the history after it is built first, and when
nothing fails there the history before it isn't built at all.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Delete: test that the check in a rolled-back history still reports what breaks (#9917)

Deleting a hole in the plate changes the plate and every cut after the
marker and breaks none of them: the check reports nothing. Deleting a
side of the outline breaks the plate, and the check still says so, with
a cache too small to keep a state.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 12:29:30 +00:00
ashxddaga 7c013333db feat(engine,ui): allow restricting point-to-point align to chosen axes (#9946) (#10015)
* feat(engine,ui): allow restricting point-to-point align to chosen axes (#9946)

* style: apply cargo fmt across crates

* fix(clippy): use filter then map instead of bool::then in filter_map
2026-10-31 12:00:17 +00:00
HiroKenEzandClaude Opus 5.5 8f259d5b83 Sketch: the Line tool can switch to a tangent arc and back without changing tool (#9489) (#9553)
* claim: #9489

* Sketch: the Line tool can switch to a tangent arc and back without changing tool (#9489)

With Preferences > Sketch > "Rest on a line's last point to switch to a
tangent arc" on (off by default), leaving the chain's last point and resting
back on it for 0.35 s makes the next click a tangent arc, by the existing
sketch.arc.tangent command, and the same gesture goes back to lines. A label
at the cursor says which. sketch.arc.tangent's end can now name an existing
point, so an outline drawn this way closes.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Sketch: the cursor label names the command in words (#9489)

The label asked the catalog for a message id that doesn't exist, so it showed
the id. It now takes the command's translated label, and the test checks the
words it paints. Moved clear of the pointer's own badge.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 11:21:59 +00:00
semmelrindeandClaude Opus 5.5 a6b9d5a5b2 Browser: a sketch shown before an Extrude still hides once it is used (#9954) (#9971)
Show/Hide put every sketch it showed in `shown_sketches`, the list of
finished sketches kept shown although a feature uses them. Hiding and
showing a sketch nothing used yet put it on that list, so once an
Extrude used it, it stayed shown instead of hiding itself as a sketch
never hidden does. Show now marks only a sketch a feature already uses;
one nothing uses is shown anyway and leaves the list alone.

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 11:19:34 +00:00
HiroKenEzandClaude Opus 5.5 5bb3b6717f Equation curves: the variable can carry its range's unit (#9333) (#9549)
* claim: #9333

* Equation curves: the variable can carry its range's unit (#9333)

A curve can set variable_unit "range" (or tick the new box in its window): the
variable is then a length, so a ^ 2 / (4 * t) is a length when a is one. Start
and end must both be lengths, or one a length and the other a plain number in
the design's unit; anything else is refused. Saved only when set, as one pending
format change; without it curves behave as before.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 10:54:06 +00:00
kaltenbrunnermarkusandClaude Opus 5.5 5b6e5815a3 Engine: lower the per-command cost of evaluating large designs (#9615)
* claim: Engine: lower the per-command cost of evaluating large designs

* Engine: lower the per-command cost of evaluating large designs

- The fingerprint texts of features are kept in one store shared by every
  worker, not per worker: a command evaluated ahead runs on a new worker each
  time, where the per-worker store was always empty and every feature was
  written out again. Same texts, same hashes.
- Pinning body names after a command keeps, per feature, the names of the
  bodies it made with the state they were read from, so it no longer searches
  every result's bodies (features x bodies per command), and finds results by
  their index before searching.
- Pinning fingerprints the timeline again only from the first renamed feature
  (or a pattern or mirror of features replaying one) when the model proves its
  fingerprints are the design's; the fingerprints are those of the full pass.
- The evaluation cache's byte count looks bodies and sketches up instead of
  searching them per body (bodies squared per feature). Same counts.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 10:51:16 +00:00
kaltenbrunnermarkusandClaude Opus 5.5 fa21db7df8 Save: hard-link the backup copy and check for unsaved changes once per revision (#9617)
* claim: Save: hard-link the backup copy and check for unsaved changes once per revision

* Save: keep the backup as a hard link and check for unsaved changes once per revision

The backup of a save is the old file under a second name (a hard link renamed over the
old .bak) instead of a copy written out again; where links are refused (FAT, shares,
cloud folders) or the old file cannot be flushed, it is copied as before. Every point a
save can stop at leaves the design file whole and the backup the version before it.

Session::is_dirty compared the whole document with the saved one each time it was asked,
which the window does every frame for every tab. The answer is kept per revision and pair
of documents; the cache holds both, so neither can change in place while it stands, and
doc_mut lets it go first so edits stay in place.

On the rover in two unsaved tabs an idle frame takes 15.0 ms instead of 19.3 ms; a save
with its backup of the 11.8 MB file writes in 9.6 ms instead of 18.9 ms.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 09:29:20 +00:00
austin62jakeandClaude Opus 5.5 b5fe8776b5 Assembly: default names skip names in use (part of #9738) (#9898)
* Claim part of #9738

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Assembly: default names skip names in use (part of #9738)

Contact sets, motion studies and exploded views were named by how many
there were, and a component's placements by how many it had, so after a
delete the next default name repeated one still in use, and commands
given that name acted on the first. They now take the first number no
item has, as joints' and the app's dialogs' default names already do; a
placement keeps the next number when it is free.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude <noreply@anthropic.com>
2026-10-31 08:28:50 +00:00
Dahak BuildsandDahak Builds 8986a670e5 3-Point Circle keeps snapped clicks as coincident constraints (#9858) (#9922)
* claim: #9858

* 3-Point Circle keeps snapped clicks as coincident constraints (#9858)

The tool sent only the three clicked positions, so a click snapped to a
point or curve left no constraint and the circle was free once drawn.
Each click now goes as its snap, as the 3-Point Arc's do, and the engine
adds a PointOnCurve for each referenced point, as the centre circle's
through click does (#3099).

* Fix #9858 test: assert the clicked midpoint point, not the line end

---------

Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
2026-10-31 08:27:13 +00:00
austin62jakeandClaude Opus 5.5 3c0d4e120e Linked designs: one changed while the assembly was closed is read again when it opens (#9739) (#9872)
* Claim #9739

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Linked designs: one changed while the assembly was closed is read when it opens (#9739)

A link now keeps the SHA-256 of its design file's bytes as the assembly
last read them (DesignLink::file_sha256, a pending format change), set by
Insert Design, Relink, Extract to File and Update Links. component.links
reports `changed` from it, hashing a file again only when its time or
size changed (vfs::design_path_stamp, behind the design-path rule). The
app treats a link it meets for the first time whose file changed as not
read yet, so opening an assembly, in its own tab or in place of the blank
design, reads those parts again as a tab coming back does.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Linked designs: read what changed last when a design opens in place of the blank one (#9739)

A read is taken up only by the design revision it started from, and
adopt bumped the revision after starting it, so the read was dropped.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude <noreply@anthropic.com>
2026-10-31 07:28:24 +00:00
austin62jakeandClaude Opus 5.5 5d9e4d5f95 joint.drive: a suppressed joint stores nothing, and the reply says what was asked and why a value differs (#9742) (#9862)
* claim: #9742

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019FAWPuFoh9qxn2uS2j53QZ

* joint.drive: a suppressed joint stores nothing; the reply says what was asked and why a value differs (#9742)

Driving a suppressed joint answered moved: false with "H is suppressed"
but wrote the values into the joint, with an undo step, so the part
jumped when the joint was unsuppressed. A suppressed joint outside any
motion link now stores nothing.

The reply gains `requested` (the values asked for, before limits and
links) and `held`: each driven value that ended up elsewhere, with why
(a motion link sets it, as a screw's travel follows its turn; a limit;
contact; a closed loop). A drive that moves nothing gives the first held
value's why as `reason`, so driving a screw's distance alone no longer
answers moved: false without one.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019FAWPuFoh9qxn2uS2j53QZ

---------

Co-authored-by: Claude <noreply@anthropic.com>
2026-10-31 05:57:24 +00:00
Dahak BuildsandDahak Builds 75b3fb678c Sketch: conflict messages no longer name a nonexistent id or claim full constraint wrongly (#9735) (#9859)
* claim: #9735

* Sketch: conflict messages name real constraints, not the refused one's id or a false 'fully constrained' (#9735)

* fmt + clippy: contains over iter().any (#9735)

---------

Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
2026-10-31 05:56:42 +00:00
austin62jakeandClaude Opus 5.5 affe37bcc3 Body names: inspect.interference refuses an unknown body; appearance.chain and appearance.list take a placed copy's name (#9740) (#9856)
* claim: #9740

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019FAWPuFoh9qxn2uS2j53QZ

* Body names: inspect.interference refuses an unknown body; appearance reads take a placed copy's name (#9740)

inspect.interference dropped a name that is no body, so a misspelled or
wrongly cased name left that body unchecked and two overlapping cubes
answered count 0. It now refuses the name, as inspect.clearance does,
naming the closest body when one is near enough to be a typo or another
case (cmd::no_body, on the existing edit_distance).

appearance.chain, appearance.list and appearance.replace's scope take a
placed copy's name (KB (K:2)) and a placement's (K:2) for the body and
component they show, as appearance.assign already does, through two
Session helpers: own_body_name (on body_frames) and component_or_placement,
which appearance.assign now uses too. A name that is neither is still
refused. select.set already refuses an unknown body on main (#9737).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_019FAWPuFoh9qxn2uS2j53QZ

---------

Co-authored-by: Claude <noreply@anthropic.com>
2026-10-31 05:07:04 +00:00
PaddleStrokeandClaude Opus 5.5 fd5d0e6738 Assemblies: mass, centre of mass and inertia per occurrence and rigid group (#9715) (#9717)
* claim: #9715

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Assemblies: mass, centre of mass and inertia per occurrence and rigid group (#9715)

assembly.mass_properties (and Session::mass_properties) gives, for every
occurrence and every rigidly-joined group, mass (kg), centre of mass (mm) and
the inertia tensor about it in world and frame axes (kg mm2), the input
the multibody dynamics work needs. Bodies are measured as Properties
measures them (kernel volume and centre, mesh gyration), once per body,
then moved by each placement and combined by the parallel-axis theorem.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 04:35:29 +00:00
PaddleStrokeandClaude Opus 5.5 c2f66107cf Sketch: paste copied sketch geometry into another design (#9258) (#9675)
* claim: #9258

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Sketch: paste sketch geometry copied in another design (#9258)

Sketch geometry copied or cut in a sketch (sketch.copy / sketch.cut) now pastes into a sketch of another open design with Ctrl+V or the context menu, at the cursor or at the copied coordinates, with the constraints and dimensions among it. A dimension whose expression names the copied design's parameters keeps its value, in its unit; a text keeps its numbers. SketchClip::for_another_design prepares the clipboard; the app keeps the last sketch copy beside the cross-design body/component copy.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 04:11:57 +00:00
Dahak BuildsandDahak Builds 91aefd5abc Refuse sketch values that collapse a curve in settle_value_edit (#9729) (#9837)
* claim: #9729

* Refuse value edits that collapse a sketch curve: settle_value_edit runs settle's shrunk/flung checks (#9729)

* rustfmt

---------

Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
2026-10-31 04:08:20 +00:00
Nathan Dane d7cba9e96d Preferences: theme options list and the opacity option (#8876) (#9807)
* claim: #8876

* claim: #8876

* Theme options: persist per-theme values and expose preferences contracts

* Restore selected theme mode after stopping a followed theme

* claim: #8876

* Preferences: render theme options and apply readable panel opacity

* Use floating-point scale expectation in theme preferences scenario

* Keep panel opacity colour construction inside theme tokens

* Complete theme options translations in Arabic Hebrew and Vietnamese

* Let standalone theme sliders fill their option cells
2026-10-31 04:01:29 +00:00
3b77567932 Docs: joint flip needs x for point origins; checkpoints are single use, 16 kept (#9746) (#9844)
joint.create's flip text and the assemblies guide said two origins at one
point with the same z stay as they are; a point origin without x takes its
x from z, so a part turned about z turns back. Say so, and point to giving
x on both origins or joint.as_built.

edit.checkpoint and edit.restore_checkpoint now say that restoring or
forgetting uses the checkpoint (and later ones) up and that only the last
16 are kept, and the "no checkpoint N" error says why. The editing and
mechanisms skills no longer read as if a checkpoint can be restored twice.

Co-authored-by: thocsmith <193096300+thocsmith@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 03:48:13 +00:00
Homero Thompson 810a9558bd perf(#3892): index the hidden joints and folders of the view (#9823)
The browser asks about every joint of the design on every frame, and
the answer walked the list of hidden joints: a nested STEP assembly
hides thousands of them, so a frame cost grew with the size of the
design.

Session keeps the hidden joints and folders as sets and answers from
them. The sets are built when the view changes and kept until it
changes again: the revision says the design changed, and the lists
say the view changed under it (the view is replaced outside the
engine too, without a revision of its own).

The behaviour is unchanged: the hidden joint stays hidden, the shown
one stays shown, and undo and redo keep the hiding right.
2026-10-31 03:01:33 +00:00
PaddleStrokeandClaude Opus 5.5 d7ae568790 Insert SVG: say why a drawing has nothing to import (#9641) (#9652)
* claim: #9641

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Insert SVG: say why a drawing has nothing to import, and read UTF-16 files (#9641)

An SVG with nothing SolidCraft draws (only an embedded picture, shapes
pulled from another file with <use>, or not an SVG at all) was refused with
"invalid parameters for sketch.insert_svg: the drawing has no geometry
SolidCraft reads". It now names the file and says why, pointing pictures at
Insert Canvas and Canvas to Sketch. SVG files with a byte-order mark or in
UTF-16 now read, and a gzip-compressed (.svgz) file is refused clearly.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Insert SVG: decode UTF-16 with as_chunks (clippy)

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 03:00:32 +00:00
momysnowandClaude 60b9e9d188 Edit Joint: show the two sides and pick them again (#9686) (#9692)
* claim: #9686

Co-Authored-By: Claude <noreply@anthropic.com>

* Edit Joint: joint.edit takes the two sides

joint.edit accepts a and b in the form joint.create takes them (read by the same origin_param), so a joint can move its attachment without being deleted. A side left out keeps its place. The two sides must stay on different occurrences, checked as joint.create does. Limits, values, expressions and the name are kept; a relation's values start again where its parts are.

joint.edit gets an input contract and reply type (schema/joints.rs), and leaves schema/unconverted.txt.

Co-Authored-By: Claude <noreply@anthropic.com>

* Edit Joint shows both sides and picks them again

The Edit Joint dialog now shows the two sides in the same selection inputs as Joint, each pre-filled with the face or edge of its own component under the origin. OK sends joint.edit a or b only for a side picked again, so an untouched side keeps its origin exactly.

Co-Authored-By: Claude <noreply@anthropic.com>

* Edit Joint: a moved side turns the part as joint.create would

joint.edit kept the joint's old angle when a side changed, so the part could turn by a half turn about its axis when the new origin's x lay the other way. When a side moves and no angle is given, the angle is worked out again as joint.create does (the least turn from where the part is now); a relation's angle is its tilt and stays.

The mechanisms reference says joint.edit takes a and b.

Co-Authored-By: Claude <noreply@anthropic.com>

* Edit Joint: pre-fill sides by name, send the angle only when changed

A side shows the face or edge its snap names, the piece nearest its stored pick when the name has several, else the one nearest that pick; it no longer searches outward from the frame origin, which could show the plate beside a hole for the hole's wall. A point or frame side shows nothing. OK sends the angle only when the user changed it, so a side moved without it turns the part as joint.create would.

Co-Authored-By: Claude <noreply@anthropic.com>

* Edit Joint: a moved side leaves an angle expression alone (#9686)

Co-Authored-By: Claude <noreply@anthropic.com>

---------

Co-authored-by: Claude <noreply@anthropic.com>
2026-10-31 02:27:54 +00:00
PaddleStrokeandClaude Opus 5.5 72a265e4fc Nightly action matrix: a sketch on the sensor enclosure lid's top keeps its attachment (#9465) (#9670)
* claim: #9465

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

* Face attachments: a piece of a face its certificate finds the other pieces of keeps that certificate (#9465)

The nightly action matrix has refused a sketch and an offset plane on the
sensor enclosure lid's underside (`examples/sensor_enclosure :: Lid/F2:top`)
since #8278. The lid's lip, joined below it, parts the underside into a ring
and a panel; the ring rests on the case and is named after the case's top,
so the lid's cap certificate (via certified_pieces) finds only the panel.
#8278 then refused the certificate because it doesn't find the picked face,
and the history-name fallback can't take a name made by another body's
feature.

A face that is no pattern or mirror copy and lies on the same oriented plane
as the pieces the certificate finds is another piece of that face: the
certificate stands for it, as before #8278. Copies (the #8278 case) still
fall back to their own history name.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 02:02:24 +00:00
PaddleStrokeandClaude Opus 5.5 9d18034e13 Sketch drag: a line is never shrunk to a point to follow the cursor (#9062) (#9728)
* claim: #9062

* Sketch drag: a line is never shrunk to a point to follow the cursor (#9062)

A line's end on a horizontal construction line through the origin, dragged
up off it, made the construction line vanish. A horizontal row is
b.y - a.y, which a line a hair long meets at any tilt, so the drag's held
solves met the point-on-line by shrinking the construction line: to 1e-5 mm
on the first frame, 1e-7 mm by the tenth, and the end went up.

A drag step (held solve, the tangent-ends-held solve, and each cursor
correction pose) that shrinks a line or circle from over 1e-3 to under
1e-4 now counts as failed, as a step that wraps an arc does. The end then
stays on the construction line, which keeps its length.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 01:54:19 +00:00
Nathan Dane 5bd5be9543 Viewport status item: standard details card (#8613) (#8614)
* Keep viewport summary menus below modal owners

* Build viewport status details from shared blocks

* Keep details focus checks outside context data locks

* Preserve native editor Escape ownership in details cards

* Initialize strict contract test sessions directly

* Translate viewport status detail cards

* Use inferred slider options and test legacy Section editing
2026-10-31 01:27:12 +00:00
PaddleStrokeandClaude Opus 5.5 2f09c90542 Exploded View: grey it out until the design has two components (#9142) (#9659)
* claim: #9142

* Exploded View: grey it out until the design has two components (#9142)

On a part made of plain bodies (the sample plate) Exploded View opened its
dialog and failed on OK with "an exploded view needs two or more
occurrences". The command is now disabled until the design has two or more
occurrences, and its tooltip says why and which commands make components.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>

---------

Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 01:18:34 +00:00
Colin Faulkingham 8311ae5c5d BOM: group purchased children under inseparable parts (#9744) (#9794)
* claim: #9744

* Fix grouped BOM children for inseparable parts
2026-10-31 01:17:58 +00:00
Dahak BuildsandDahak Builds 4973638b56 Selection follows body rename so Delete targets the right body (#9737) (#9789)
* claim: #9737

* Selection follows body renames; stale body selections are dropped (#9737)

---------

Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
2026-10-31 01:17:28 +00:00
Colin Faulkingham f73479ddf2 Preserve multiline fields and accept a BOM in parameter CSV imports (#9732) (#9772)
* claim: #9732

* fix(params): preserve quoted CSV records and BOM headers (#9732)
2026-10-31 00:46:57 +00:00
Dahak BuildsandDahak Builds 772815b4c0 Sketch Extend: only an end on a circle counts as held (#9731) (#9773)
* claim: #9731

* Sketch Extend: only an end on a circle counts as held (#9731)

grow_line's on-circle test was true for every point inside the circle; test distance to the circle instead. Also pin the new end point of a held-end extension onto the curve it stops on, as the free-end path does.

* Fix regression test harness usage and held-end setup (#9731)

---------

Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
2026-10-31 00:45:22 +00:00
Erlis Vidal 6d89de1f5a Construction planes, axes and points hide with their component's placement (#9790) (#9791)
construction_visible checked the item's own hide and its folder, but not
the placement its component is drawn at, so hiding Part:1 left Part's
planes, axes and points on screen. It now asks feature_placement_visible,
the check sketches already made; the placement path is computed in one
place for both.
2026-10-31 00:44:47 +00:00
Colin Faulkingham 0fe5bf114c Timeline: resolve exact feature names before ID fallbacks (#9689) (#9748)
* claim: #9689

* Resolve timeline names before falling back to feature IDs
2026-10-31 00:08:24 +00:00