* Themes: Clay (light) and Clay Dark, warm paper and charcoal with a terracotta accent
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Clay: on-accent text a touch lighter for 4.5:1 on the accent
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Axes and points from circular edges and round faces
In 3D, a round edge or face stands for its circle wherever a command
takes an axis or a point.
Revolve, Surface Revolve, both Circular Pattern dialogs, Plane at Angle
and Move -> Rotate take a circular edge (through its centre, along its
normal) or a cylinder, cone or torus face (its axis). The features keep
the pick as a model reference, so they follow the model when a parameter
moves it. Straight edges work as before; flat faces are refused.
Every 3D point input takes a circle's centre: construction points (which
follow the circle), To Object, patch points, hole placement, and Move's
pivot and points. Hovering shows the axis as a dashed construction line
or the centre as a star, and the dialog's chip names what the pick
stands for ("centre of edge 10", "axis of face 3").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Format the round-pick hover check
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Selection chips: name a round pick as a circle centre or axis
The chip has room for little more than the body and a word or two:
"Shaft · circle centre", "Shaft · circle axis", "Shaft · face 2 axis",
and "Shaft · point" for a point of the model.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Move: a circle's centre in a placed component is where the component shows it
Move's pivot and points read a picked circle from the model in its
component's own frame, while the pick is in the world. They now read it
from the world state (and, editing a Move, from the state before it,
placed the same way), as the viewport and the other round picks do.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Plane at Angle on a planar face about a model edge: test that it follows both
Upstream #1956 made a planar face a base for Plane at Angle; this branch makes a model edge an
axis. The rebase keeps both in one PlaneRef::AtAngle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Expressions: a number and its unit are one value (10 mm / 2 mm is 5)
A unit written after a number was multiplied in at the precedence of `*` and
`/`, so `10 mm / 2 mm` was (10 mm / 2) mm = 5 mm² and `90 deg / 1 rad` a value
in angle², reported as a unit error. The number now takes the unit after it
before `*` and `/` apply; a fraction of numbers before a unit stays one value
(`1/2 in` is half an inch), and an exponent stays a plain number (`2^3 mm`).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Expressions: after a division, a fraction before a unit only when closed up
`width / 10 / 2 mm` read the `10 / 2 mm` as the fraction 5 mm and gave
width / (5 mm) = 8 instead of (width / 10) / 2 mm = 2. After a `/` the
fraction rule now needs the fraction written without spaces (`1 in / 1/2 in`
is still 2); elsewhere `1/2 in` and `10 / 2 mm` are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
?open= now also accepts an absolute path on the page's own origin, fetched
with the page's scheme, so a self-hosted setup that serves SolidCraft and
other tools under one origin can link a design on a LAN without a public
HTTPS address. Absolute URLs keep the HTTPS-only rule (a URL on the page's
own origin is also accepted), redirects must end on HTTPS or the same
origin, and protocol-relative, dot-segment, backslash and control-character
values are refused.
* claim: #3538
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Updated AppImage takes the release's file name (#3538)
A versioned AppImage name (solidcraft-<version>-linux-<arch>.AppImage) is
replaced by the new release's name, so zsync-based tools keep finding the
update data. Other names are kept.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
* claim: #6558
* Shortcuts: Ctrl+Shift+S opens Save As in the workspace (#6558)
The Home page already opened Save As with Ctrl+Shift+S, but the design workspace matched Ctrl+S, so the chord saved over the current file instead of offering another one. The workspace now routes the chord to Save As, and the File menu shows that shortcut next to Save As, taken from the command registry.
The catalogue entry Quantity served both the pattern dialogs' number of
instances and the motion study's plotted quantity. Nine locales had
translated the second meaning, so the rectangular pattern dialog showed
e.g. "Größe" above "Anzahl 2" in German.
The motion study's row now reads motion.plot_quantity (a pending file
that keeps every locale's previous word there). Quantity takes each
catalogue's own ui.quantity text, which the "Quantity 2" row already
shows; nothing is newly translated. The glossary lists Quantity under
words with more than one meaning.
Fixes#6538
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
SolidCraft runs through XWayland whenever an X display is available. A
compositor that doesn't let X11 apps scale themselves draws the window at
100 % and stretches it. docs/nix.md said so only for fractional scaling,
but GNOME 47 (RHEL and Rocky Linux 10) does it at any scale: the report
shows 1.05 physical pixels per point at 200 %.
The troubleshooting page gets a section with the cause, the Window system
preference, SOLIDCRAFT_WAYLAND=1 for 0.21.0 and earlier, and the file drop
trade-off; docs/nix.md links to it.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Saving into Documents fails with the Windows dialog's "File not found" when
Controlled folder access blocks the app, and the message gives no hint.
Refs #4479.
* claim: #4640
* Docs: AppImageLauncher 2.x can't start the AppImage; update to 3.0 (#4640)
AppImageLauncher 2.x intercepts every AppImage through binfmt_misc and
can't start static-runtime AppImages such as SolidCraft's: it fails with
"execv error: No such file or directory" after a FUSE message. 3.0 starts
it. One paragraph in the Linux AppImage section says so.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Docs: AppImageLauncher 3.0 is so far only published as betas (#4640)
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
* claim: #4851
* User guide: local models with the Assistant (#4851)
A page on choosing and setting up a local model (Ollama, LM Studio, or any
OpenAI-compatible server) for the Assistant: tool support, VRAM, permissions,
the measured results from the standard test in #4851, and troubleshooting
for the common failures.
* Guide: local models table with the full set of measured results
Point to the `<file>.bak` copy every save keeps, the design.solidcraft in crash
reports, the recovery folder for unsaved designs, and how to attach the file
to an issue.
* Every new command comes with input and output schemas
A test fails for a command without a contract or an output type, unless it is a planned!
placeholder or listed in schema/unconverted.txt, which holds the 400 commands that predate
the rule and only shrinks: the test also fails when a listed command has its schemas, when
the list names a command that doesn't exist, or when it isn't sorted.
`checked!` now takes only the command's id and checks the contract that id publishes
(`run_checked_as`), so the contract enforced is always the one described. Another test runs
every command that has a contract in strict with an unknown key, so a contract is never
published without `checked!`, under the command's own id, enforcing it.
A new book page, Command schemas, explains how to write a contract and a reply type, the
tests to add, the shared field types and how to add one, with a checklist; the failure
messages point to it. "Adding a command", CONTRIBUTING.md and AGENTS.md now include the
schemas, and the MCP tool description and docs/mcp.md no longer list the converted commands.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* List the commands added on main since: view.layout, view.history_layout, view.normal_to
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Command schemas guide: what participants and targets do, checking the evaluation, warning-free replies
- `participants` changes the result for some features and nothing for others; where it and
another key override each other, or where it has no effect, say so in that key's
description or in the summary.
- The example primitive's `targets` default to every body in the feature's component, not the
bodies it meets; they're ignored when `participants` lists bodies.
- Check what each value does where the feature is evaluated, not only how the handler reads it.
- A reply test runs every form in Warn and checks for no `param_warnings` (Strict for a reply
that isn't an object).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* List the 43 commands added on main since: frame, component, render and others
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* List the 11 commands added on main since: browser folding, standard views, parameter sweep, path flange
browser.collapse_all, browser.expand_all, inspect.parameter_sweep, sheet.path_flange and the
seven view.* standard views (back, bottom, front, isometric, left, right, top) landed on main
without schemas; the gate flags them, as intended. 457 commands listed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Schema rule warns instead of failing for now
A command without input and output schemas prints a warning listing it
(test output and a CI annotation). SCHEMA_RULE_STRICT in coverage_tests.rs
(or SOLIDCRAFT_SCHEMA_RULE_STRICT=1) makes it fail again. Docs say "should,
and will become required".
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #4146
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Viewport theme: a light 3D view in a dark window, and the reverse (#4146)
Preferences › Interface › Theme gets a Viewport row under the theme tiles:
Follow theme (the default, as before), Light or Dark. Light or Dark draws
the 3D view in the built-in Light or Dark theme's colours whatever the
window uses, so a dark window can show the model on a light view and the
other way round; it works with every theme, theme files included.
The view takes the background and grid, bodies, selection and hover, the
origin, previews, sketches with their dimensions and glyphs, the navigation
cube and triads, box selection and the analysis colours. Panels, dialogs,
menus and the chips over the view keep the window's. Text and warnings drawn
straight onto the view (the sketch status line, the loose-end and midpoint
markers, the section's cut outlines, the 3D sketch tool and the sketch tools'
previews) take the view's side, so they read on its background.
theme::ViewportTheme is the setting (saved as `viewport_theme`: theme, light
or dark; an unknown saved value reads as Follow theme, as ColorVision's
does). Tokens::get() takes the view's colours from the other side only when
the view's dark or light differs from the window's; Tokens::view() is the
view's side for colours drawn onto it. The ground shadow follows the view
(the scene and highlight caches already key on the colours themselves),
ui.render draws in the view's colours, and ui.prefs takes `viewport_theme`
and reports `viewport_dark`. An older release ignores the setting and draws
everything in the theme.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Viewport theme: follow the single set of axis colours
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #754
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27
* Sketch Dimension: arc length from an arc and its end point (#754)
The arc-length dimension existed (sketch.dimension type arc_length) but
the Dimension tool could only give an arc its radius. An arc and one of
its own end points, in either order, now dimension the arc's length:
click the arc, then its end. The pair was refused before ("cannot
dimension that combination"), so no existing result changes. A point
where the arc's end is (a coincident line end) counts as that end.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #2348
* Open linked designs from assembly browser
* claim: #2348
* Test linked design action with multiple components selected
* Fix linked design lookup in browser storage and translate its menu action
* Add Turn Up Axis to complete UI catalogs
* Keep browser DXF download after linked-design checks
Search Console lists docs.solidcraft.io/, /introduction.html (the same page) and /guide/mcp.html as duplicates without a user-selected canonical. The Pages build now adds a canonical link to every book page (index.html and introduction.html both name /), skips the redirect stubs that already have one, marks 404 and the toc frame noindex, and writes a robots.txt pointing at a generated sitemap.xml.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #976
* One set of X, Y and Z colours for every axis (#976)
The origin axes, the navigation cube's triad, 3D sketch triads and joint
origins drew `axis_x/y/z` (255,0,0 / 0,255,0 / 2,2,248), the view triad and
the headless picture drew `triad` (220,60,60 / 60,170,60 / 60,100,230) and
the Move gizmo drew `gizmo` (225,70,60 / 80,190,80 / 70,130,240). The
`triad` and `gizmo` tokens are gone: every axis reads `axis_x/y/z`, now the
view triad's values (the engine's `view::colors::AXIS_*`, so headless
pictures are unchanged, and the set the red-green table was measured for).
Older theme files' `triad` and `gizmo` lists still read and set the axes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Themes: Okibi (dark) and Akari (light), from the Okibi design system
Two built-in themes mapped from the Okibi design system v1.8
(https://kaievns.github.io/okibi-akiri-design-system-spec/): cool charcoal
ash with a single ember accent, and its warm-paper light twin. Every one of
the 156 colours is set, so nothing falls back to the Dark or Light palette.
* Give the Okibi and Akari themes an icon palette
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #5938
* Edge flange: height measured from the outer sharp, the inner sharp or the bend tangent (#5938)
An edge flange feature takes height_from (outer, inner or tangent) in sheet.flange and Height From in the Flange dialog, saved only when it is not the outer sharp. A height shorter than the bend takes is refused with the smallest height that fits.
* Edge flange: material outside and tangent bend positions (#5941)
An edge flange's position can now be material_outside (the inner virtual sharp on the edge) or tangent (the bend's outer face tangent to the edge's face), in sheet.flange and the Flange dialog. The bend starting at the edge was already the outside position, which now also answers to bend_outside.
* claim: #6252
* Open hosted designs in the web app and add an embed layout
Fixes#6252.
Fetch HTTPS design links with bounded reads and open them as unsaved copies.
Keep model panels and joint controls in embeds without browser persistence,
application chrome, or unload prompts. Add a full-app link and iframe docs.
Cover query parsing, hostile URLs, size limits, and the compact layout.
* Translate the linked-design messages into Japanese and Chinese
* claim: #4094
* Sheet metal: Path Flange, a chain of bends on an existing sheet edge (#4094)
Path Flange (`sheet.path_flange`): sketch an open chain of lines across a sheet edge, pick the
edge and one line; each line becomes a flange as long as the line and each corner a bend, one
feature and one body. The edge flange takes further bends (`then`), each on the far edge of the
one before, and the Flange dialog shows them as rows with a bin each.
* claim: #3271
* fix(ui): use document units across length fields (#3271)
* Format
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Adapt drag-extrude and joint tests to document-unit length helpers
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* fix(ui): preserve blank parameter drafts and cover bounded lengths
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #2320
* Value fields step with the arrow keys and the mouse wheel (#2320)
Up/Down in a focused value field step a plain number by 1 in the unit it is written in
("20 mm" -> "21 mm", "2,5 mm" -> "3,5 mm"), 10 with Shift and 0.1 with Alt; the wheel over
the focused field does the same, a step a notch, instead of scrolling the panel under it.
Expressions such as `width / 2` are left as typed, and an open completion list keeps the
arrows. Every expression field gets this through `params_dialog::complete`: the value box
beside the geometry in every dialog, the dialog rows, sketch dimensions, the dimension
editor, Drive Joint and the Parameters window.
* The value box beside the geometry stays under the pointer
The box rides on the arrow's tip, so each wheel notch that stepped its value moved it, and
after a notch or two the box slid out from under the pointer and the wheel zoomed the view
instead. While the pointer is over it the box now keeps its place, and it goes back to the tip
when the pointer leaves.
* Value stepping is a preference, off by default
Preferences › General › "Step values with the arrow keys and the wheel" (`step_values`,
also through `ui.prefs`) turns on Up/Down and wheel stepping in value fields, and the value
box staying under the pointer while the wheel steps it. Off, as by default, value fields
behave as before: Up/Down move the text cursor, the wheel scrolls, and the box beside the
geometry follows its arrow.
* Value stepping test: Bend Radius is under Advanced now
* Value stepping test: the preference is on the Design page
* Value stepping test: draw the field straight into the test's frame (#2320)
The shared outer-host rule now covers tests too; the field needs no panel around it.
* claim: #4968
* Sheet metal rules: bend angles as the included angle (#4968)
A sheet metal rule's angle_display (bend, the default, or included) sets
how the DXF bend notes read each bend: a 58° bend is B1 UP 122° R1 under
an included rule. The bend table always gives included_angle_deg beside
angle_deg (CSV and JSON). Set in sheet.manage_rules and the Sheet Metal
Rules dialog, listed by sheet.rules; the flange angle stays the bend angle.
* Bend table: the included angle as the CSV's last column, so the columns before it keep their places (#4968)
A test also covers a body whose base flange names its rule, which keeps that rule's notes whichever rule is active, and a bend down.
* Sheet Metal Rules: Angle Display reads Bend or Included, so the choice fits its box (#4968)
The rule editor's row contract lists the new row and the key the dialog sends.
---------
Co-authored-by: begsaquib <saquibbeg4444@gmail.com>
* Sketch Dimension: point or circle to the edge of a circle or arc (#4064)
Adds PointCircleDistance and CircleCircleDistance (edge-based, like #1863):
solver, constructive seed, drawing, command wiring, tests, UI scenarios and docs.
Saved designs gain two constraint kinds, in one pending format file.
Fixes#4064.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Sketch Dimension scenario: pick the circle at its top edge (#4064)
The bottom edge sits under the Dimension tool's status hint in the scenario window, so the second click never reached the tool.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
* claim: #5467
* Warn when a design is open elsewhere or changed on disk (#5467)
The desktop app keeps a lock file next to each open design
(.~<file>.lock: computer, user, version, opened and refreshed times),
refreshes it every minute and removes it on close; a lock not
refreshed for three minutes is stale and ignored. Opening a design
that another SolidCraft has open asks: Open Read-Only, Open Anyway or
Cancel. A read-only design saves only to another file.
A design remembers its file's size and modification time when it is
opened or saved. Save over a file another program or computer changed
since asks: Save a Copy (the default), Overwrite or Cancel.
Programmatic calls never ask: doc.open reports open_elsewhere and takes
read_only, and file.save over a changed file returns an error until it
is given overwrite: true. ui.documents answers both questions.
* claim: #2063
* Windows OpenGL: use the system title bar so the picture lines up with clicks (#2063)
On Windows with only OpenGL to start, the window opens with the system
title bar instead of using the application bar as its title bar. The
window without OS decorations keeps its caption style while having no
frame, and some OpenGL drivers (older Intel HD/UHD) show the picture a
caption's height lower than the window, so clicks land above what they
point at. Direct3D 12 and Vulkan keep the custom title bar.
The choice is made before the window opens, from the backends wgpu
starts, so the window never changes its frame while OpenGL draws into it.
sheet.export_dxf always wrote the dashed bend lines (BEND_UP,
BEND_DOWN) and split the flat pattern over a layer for each role. A
cutter that cuts every line it is given cut the bend lines too.
bend_lines: false now leaves them out, and layers: single writes every
entity on layer 0. The defaults keep today's output.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* inspect.parameter_sweep: check a design across a parameter's range
Rebuilds a copy of the design at each value of a parameter and reports what
no longer holds compared with the design as it is: features that fail or
warn, joint origins that are lost or turn over on their own part, sketch
planes that turn over, and sketch solves that fail or fold. The design is
not changed; each value's rebuild time is reported too.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* inspect.parameter_sweep: params doc matches what it takes and returns
`steps` takes at most 199 (200 values), as the check says; failed and
warned entries carry the feature's name; a lost origin says which one; a
value the parameter refuses gives {value, ms, ok: false, error}. The
refusal test covers steps 200.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* inspect.parameter_sweep: Japanese and Chinese labels
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01Aac7mP9rthK3WsPpPRvCsF
---------
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Performance overlay: frame-time graph and histogram, triangles, draw calls (#2548)
Net change of the perf-overlay branch, rebased onto main as one commit.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Document frame_rate_details in ui.prefs
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #4098
* Extrude: document which way a positive taper goes (#4098)
A positive taper slopes the walls outward (the far end is larger along the
extrusion direction), a negative one inward. Say so in the params doc, the
JSON schema and the guide, and pin the sign with a test.
With Sketch Dimension on and nothing picked yet, a click on a dimension
that is already in the sketch opens its value box, the same in-place
editor a double-click opens without a tool. Enter applies, Esc cancels,
and the tool stays on for the next dimension.
The dimension's text always takes the click; its lines only away from
sketch points and curves, which still start a new dimension (the rule
plain selection uses). Once a new dimension is under way, clicks keep
their meaning. Dimensions off in the selection filter are left alone.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Ctrl+1…7 turn the view to the standard views (#5057)
Front, back, left, right, top, bottom and isometric, handled with the
other view keys beside Ctrl+8: animated like the view cube, reserved so
no command can take them, and ignored on the flat pattern page.
* Front … Isometric View are commands, Ctrl+1…7 their default keys (#5057)
The standard views become seven commands (view.front, view.back,
view.left, view.right, view.top, view.bottom, view.isometric) whose
default shortcuts are Ctrl+1…7, instead of keys the window handles
itself. They show in Keyboard Shortcuts, can be moved to other keys or
cleared, and the digits can be given to other commands. In the app they
turn the view as the view cube does; headless they set the session
camera, keeping target, distance and projection.
Open or close every Browser folder from the design or a component menu,
including folders that start closed. Display only: not saved, not an undo step.
* claim: #3713
* Exploded views export as an animation (#3713)
motion.export_animation takes an exploded view (view: id|name) as well as a
study or a joint: the parts come apart at a steady pace from the assembled
placement to where the view shows them, and back together with back: true
(exploded at the middle frame). 41 frames by default, 81 with back. The home
view frames the parts both assembled and exploded. As with explode.show, the
design keeps its placements, its history and its saved state.
explode.show and the export share the moves; moves a design file gives with
no finite translation are left out.
* Mechanisms skill: an exploded view's default frame count
---------
Co-authored-by: MateuszSychXpl <151755914+MateuszSychXpl@users.noreply.github.com>
bherbruckandClaude Opus 5.5
Jesper We
amolinari-autotex
froglemonade2andClaude Opus 5.5
ivisafandClaude Opus 5.5
Victor Santos Oliveira
raykholo
rlartotandClaude Sonnet 5.5
Dahak BuildsandDahak Builds
Homero Thompson
Lars Jansen
ThoschandClaude Opus 5.5
leValdemar19andClaude Opus 5.5
ChrisNo
HiroKenEzandClaude Opus 5.5
Ahmad Khan
Matt Van Horn
rbousigues88andClaude Sonnet 5.5
Colin Faulkingham
semmelrindeandClaude Opus 5.5
NOWN-DEVandClaude Opus 5.5
HerperlerpicusandClaude Opus 5.5
Sandmann
Mateusz SychandMateuszSychXpl