The r1 round of a block's top edge, chained onto the end curve of the r2
round of its arc at a cylinder (rig fillets/every-block-cylinder-crease-
top-edge-after-arc-round-r1), ends where it runs into the cylinder. That
edge is no seam of the r1 round: the cylinder is a face of the r2 round,
not of the r1. blend_seams takes it for one today (the r2 round's name
F3:blend:F1:+z|F2:side holds a | of its own), and the rig reads it as a
contact seam at 60 degrees.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A projected spline edge of several Bezier spans came into the sketch as one
curve per span (#1508), so a G2 round's bottom edge was 16 curves and a path
naming the corner named one span of it (#3604). The kernel now reads such an
edge (a spline, or an elliptical arc of several spans) as the one clamped
B-spline it is over the edge's interval, its knots and weights its own, and
the sketch takes it as one control spline whose ends sit on the edge's
vertices. Planar regions still read edges span by span. The 3604 case builds
with its original path and leaves KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A sketch spline over control points was always the clamped uniform B-spline
over them, so a free-form edge whose knots are not evenly spaced (or whose
weights are not 1) could only come into a sketch as one curve per Bezier
span. A control spline now may save `nurbs`: its clamped knots and its
weights. Its points, polyline, exact pieces (one a knot span; conics for a
rational quadratic), the solver's distance and curvature, links, parallel
re-projection and inspect.sketch all read them; a loaded design's are
checked. One pending format file (spline-knots).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The tangent and curvature run-offs of the quarter cylinder r 10 strip, 5 across the surface,
are its section swept 20 along z: exactly 10 pi/2 20 + 5 x 20 = 414.159265. measure is SMLib's
integration on the exact surface (1e-8), not a mesh, so the run-off check is 1e-6 relative and
the 'measured on meshes' notes go. Red until SMLib's extension is solved to its distance
(smlib-extend-converges 590d8a1): eaa998a's curvature run-off is 4.986 long, area 413.882.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The path chain oriented its first piece, not its first curve: a first curve
of several exact pieces (a fit spline, an ellipse, a projected free-form
edge) was never turned round, so a path whose next curve meets it at its
start was refused as "not connected end to end". The chain now orients
curve by curve: the first runs toward the second where they meet at one
end only (else from the end nearest the profile), each next one starts
where the previous ended, with one joint tolerance for both questions.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Owner ruling d6: the letter t of "tres long" was drafted inward by SMLib (its
loop's normal, summed from the cross products of its chords, pointed down;
fixed in SMLib). With the fix every letter grows, and the join builds at 3°
and 15° by the Round rule and by the default rule (tangent for spline
outlines), where before 15° was expected to be refused.
Exact where the outline derives it: a letter's section at height z is its
outline offset by e = z tan a, by the Round rule of area A + P e + C e² while
the offset trims nothing (Steiner; C half each loop's turning less
tan(t/2) - t/2 at each reflex corner), so the letter is
A h + P k h²/2 + C k² h³/3. Each extruded alone, the t at 3° and s, l and o
at 3° and 15° are checked to 1e-6 (SMLib measures them within 1.3e-9; its
mass properties integrate to 1e-8). The concave joins of r, n, g and e are
tighter than e already at 3° (their swallowtails trimmed: r 1.1e-3 under the
formula), the t's by 15° (9.9e-5 over), and on the block the letters grow
into each other, so the whole word is checked for what holds exactly: one
closed body with the block, and half-way up every point of each straight
letter's outline inside the solid (the t drafted inward failed that).
With SMLib's fix (smlib-batch-4-text-loops 82133b2).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib (smlib-batch-4-rulings 0e83cca, SMLIB_ABI_VERSION 5) rounds the edges whose rounds overflow
their faces first and then what is left of the others; smlib_blend_dropping says which picks'
edges the overflow removed whole. The smlib crate binds it (Brep::blend_dropping), the kernel
returns those picks (fillet_removing), and a fillet notes them as its warning: "the edge at
(0, 0, 10) was removed by the larger round, so it is not rounded" (a 50 x 50 x 20 block, R21 on
its bottom front edge with the front left upright: the block is R21's alone, in closed form).
Ruling d8: [21, 5, 5] on a 20 cube builds as R21 alone (6107.529370); the test is no longer
ignored. R25 with R2 at a corner (blend_corner) builds the same way, R25's alone in closed form,
where it was refused. The rig's 1080 notched block outline at R8 builds now and comes off the
known-failing list.
Needs SMLIB_REV at that SMLib once it is pushed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib measures an extension's distance across the surface (smlib_extend_sheet corrects
CreateExtendedSurface until the parameter line through the side's middle is that long), so each
run-off of the cylinder strip, swept 20 along z, adds 5 x 20: 10 pi/2 20 + 100 = 414.159 for
both. The parabola-length formula (418.18) was truck's.
Ruling d2 (2026-10-30).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Two box edges rounded r2 in one fillet, then the upright edge at their mitre r3 in a second
fillet (tangent chain on, so the seam comes with it): 10 faces, 7928.743041 mm³ as
fillet_radii of the box gives, the r2 rounds' names kept, the r3 round and the corner patch
the second fillet's.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The L's six sides, its two caps and the bore: since tangency-labs/smlib#67 the
full circle the conversion fits extrudes to one full-turn wall, not two halves.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Design preference surface_extrude_symmetric_per_side, which gave new
symmetric surface extrudes their distance on each side, is removed with
its Surfaces section, its session field and its labels. A symmetric
surface.extrude given no convention splits the total around the start
plane, as solid.extrude does; timeline.edit and timeline.redefine give a
one-sided extrude made symmetric the same. default_extrude_convention,
which only existed to read the preference, goes too.
An explicit `convention: legacy_per_side` and the marker saved designs
carry are unchanged. A saved preferences file that carries the key loads
as before (the prefs test now covers both removed keys).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Design preference metric_tap_drill_major_less_pitch, which gave new
metric tapped holes the major diameter less the pitch (M8: 6.75 mm), is
removed with its Holes section, its session field and its labels. A new
tapped hole given no diameter drills the tap maker's drill (M8: 6.8 mm);
a custom metric size the table lacks still takes the major less the pitch.
A saved preferences file that carries the key loads as before: serde
ignores keys Prefs doesn't have, and the key is not written back.
The preference's UI test becomes an engine test of the default drill
(M8, 1/4-20 UNC, a given diameter) and a prefs test that a saved file
with the removed key still loads.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since the body check mode became part of the evaluation context (9acbcf924),
evaluate digests the context with the mode, but Model::adopt still took the
context without it and the default mode: the first evaluation after opening a
design from its saved model saw another context and recomputed every feature
(undoing_an_edit_after_opening_reuses_the_saved_results,
rolling_the_marker_back_keeps_results_after_cache_eviction). The saved model
now records the mode it was evaluated under (thinned ones too), adopt takes
it and digests the context as evaluate does, and a session opening a design
under another mode evaluates it again rather than showing that mode's results.
Model cache format 6.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Tests that asserted an older design rebuilds as the build that saved it made it
now assert what still holds: it opens, is upgraded, evaluates, round trips and
names alike every time, and a feature that lost a reference asks for it again.
- naming corpus: two builds still name every face and edge alike and find the
same faces with their stored names; a stored name that finds nothing must
leave its feature failed (it asks to reselect), never a feature that builds.
A sketch's face is found by its name as the sketch finds it.
- design corpus: the volumes, areas and bounds the saving builds recorded are
no longer compared; a corpus design may fail only by a request to reselect,
and undo leaves the features that failed on opening failed.
- fixed robustness seeds: no panic, valid bodies and volumes moving the right
way; a step the kernel refuses is not a bug.
- a format 28 design's pieces and a format 13 design's extra bodies: marked as
they open and named alike, without promising the numbers or names saved.
- action matrix baseline: the two corpus designs whose fillets, chamfer and
offset face held names saved before format 14 re-recorded.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Face and edge names stored before format 14 were worked out from geometry and
open marked `?`. They were found among the names geometry gives today, as the
builds that saved them found them, pieces by the one nearest the pick. They
find nothing now: the feature holding one fails, asking for its reference to be
picked again, which stores its exact name. The legacy face and edge names a
body worked out for them are gone.
The tests that found such names as saved now assert the request to reselect:
a saved strip projection, a version 9 emboss on an annulus, a format 10 face
sketch and the corpus design named with numbered pieces.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A face or edge name a feature stored finds only the face or edge it names: the
very name (or a synonym of that face), or the named piece told apart by the
faces around it. A face split into several pieces, merged into another face,
or left only as a face of the same stem is not the face that was picked, and a
name found on several bodies is told apart only by the body the reference's
point lies on. The fallbacks are gone: no piece nearest the pick, no merged
face, no edge at the picked point, no lost link that keeps its last geometry.
A feature whose stored reference finds nothing fails with DocError::Reselect:
blends, face points, sketch planes, sketch projection links, construction
references, hole reference edges, sheet bend edges and cylinder emboss.
The tests that asserted a fallback now assert the request to reselect: split
and removed fillet edges, a merged or rejoined face, a projected edge that was
split or is gone, a projection whose body went, saved strip projections after
wall coalescence, a fillet saved on a piece of a tapered side that is whole
now, a cut that starts from a piece that is no longer that piece, and a fillet
named on the lower of two stacked boxes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A side drawn in collinear sketch pieces is one face the extrude made from each
piece (#1788): its first role is its name, and the others were kept as aliases,
like the names of faces merged into it by a later join. They are names of that
very face, not of faces merged into it: the face keeps them as synonyms, which
a stored name matches as exactly as the face's name (a piece of it, once it is
split), through copies and later features, and the face whose name a merge
keeps keeps its synonyms too. An extrude-side certificate made on one of the
pieces finds the joined face the same way, and the saved model records the
synonyms (model cache format 5).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With input and output schemas. The mode is the session's user setting:
kept when another design is opened, started, recovered or imported (each
evaluated under it), and by timeline.compute_all. Linked and extracted
designs are evaluated under it too.
fillets/1080-chamfer-runs-into-openings-refused already expects the
9 mm chamfer built and cut by the openings (V = 3350); its id said it is
refused. It becomes 1080-chamfer-runs-into-openings-cut-by-them, and
blend_fit's chamfer_through_the_openings_is_cut_by_them names it so.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A joint drive with contact on tested each sample and each of 14 bisection
steps with a brute-force mesh-against-mesh overlap check, its cost the product
of the two display meshes' triangle counts under a fixed budget. Since the
display mesh puts nodes inside planar faces, a cam and its tappet or a block and
a sphere exceed that budget ("motion exceeds contact sweep collision budget"),
and whether a motion may run depended on display tessellation.
Now, at each sample, bodies whose exact boxes meet are intersected exactly
(SMLib boolean, exact volume); a shared volume is a contact, a touch (a cam and
its follower) is none. Between the last clear sample and the first overlapping
one the drive closes in by conservative advancement: from a clear placement it
moves no point of the pair further than the pair's exact gap (body_distance),
until the gap is within 1e-9 of the bodies' size. Only clear placements are
measured, so no intersection is asked to tell touching from overlapping within
its tolerance (SMLib's boolean fails there, status 1001, on two cubes 1e-4
into each other). The budget is 2048 intersections per drive.
Fixes cmd::joints::tests::cam::a_cam_drives_a_closed_loop_and_stops_at_a_contact
and contact_sweep ordinary_curved_bodies_stop_at_their_contact_within_the_sampling_budget,
and the other contact, cam, motion, interference and clearance tests pass.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The test it replaces probed for a polyline by placing a 0.2 um square in the
gap between the rim and a 1 um polyline: a micro feature in a millimetre part.
This one asserts the property itself, in millimetres: every rim segment of the
flat pattern is an arc of radius 10, the DXF draws one circle of radius 10, and
a 1 mm cut 0.5 mm inside the rim stays one hole.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
patch_continuity_and_points_cap_a_tube listed "g3" among the values surface.patch must refuse,
from #1521 when a patch built G0 to G2. Since cb8712aa0 Construction::Patch builds G0 to G4
(continuity_order.rs: `Construction::Patch => (G0, G4)`), so g3 is accepted, as it must be;
the order above what a patch builds is g5.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
raked_wedge (#1617, test from 7f2ae11a0 on 2026-10-17) rounds four end edges R4. Since
84bd2daad (2026-10-22) solid.fillet carries each picked edge round its tangent chain by
default, so the R4 now ran on round the end outline onto the R1.2 round's end arc, where the
round's rail on the end face would be an arc of radius 1.2 - 4 < 0, and it is refused as too
large. The issue's R4 rounds those four edges alone: the step says tangent_chain: false.
The test still fails, one step later, on SMLib: the issue's R0.854 round of both ends' outline
is refused by SMLib's own check (SmBSplineSurface Test #5, "close to singular at boundary"),
reported for the SMLib batch.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
tiny_cut_inside_exact_circle_survives_unfold_refold_and_dxf cut a 50 nm square 0.2 um inside
the disc's rim. SMLib models at a zone tolerance of 1e-4 mm: its check refuses the cut's 50 nm
walls as planes "degenerated to a point (tolerance=0.0001)", so the extrude was refused. A
feature below the kernel's resolution is not one it can keep, on any path.
The test's point is that the exact circle, not its display polyline, bounds the flat pattern:
a cut between the two must survive unfold, refold and the DXF. The polyline at 1e-3 has 224
chords (sagitta 10 (1 - cos(pi/224)) = 0.98 um), so the square is now 0.2 um across, centred
0.4 um inside the circle on the first chord's bisector: outside the polyline, inside the
circle, its walls and its 0.3 um gap to the rim above 0.1 um. Its hole's area is
(2e-4)^2 = 4e-8 (was 2.5e-9 for the 50 nm square).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Zebra, Draft, Curvature Map, Environment Map, Accessibility, Continuity,
Isocurve and Curvature Comb are one group: turning one on turns the one on
before off (Session::analyses_off), and the session says which is on
(Session::active_analysis). The new inspect.analysis names it and off: true
turns it off (typed contract and reply). The toolbar shows the active one's
button pressed, its tool running or not. Curvature Comb's button toggles:
on, the tool combs the edges clicked; again, off and the combs go; Esc or a
right click in the tool turns it off; opening another dialog leaves it on.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
inspect.curvature_comb keeps what it shows in the session (Session::comb):
add: true combs the new picks together with those shown, so every comb
shares one scale and tooth lengths compare across curves (a curvature jump
where two edges meet shows); with nothing picked it draws those shown again
with new options; clear: true ends it. Each sketch curve keeps its own
sketch. The tool runs it once per pick and per Comb length / Teeth change,
and the viewport draws the session's combs.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This replaces the spline fallback of 64efbe7f6. A face SMLib holds as a rational spline that is
an extruded circle was recognised as a cylinder over the spline's whole parameter range: for the
upper half of the peg's wall after the front top round that range runs 393 degrees round (u in
[-15, 40.18], SMLib's support surface extended past the face), and SMLib refuses a cylinder past
one turn. The face itself, its loops' box, spans u in [0, 8 pi]: half a turn. The cylinder now
takes the face's trimmed range, the least and greatest u and v of its uses' pcurves over their
edges' intervals, found to rounding on each Bezier span (the values at the pieces' ends bound the
extreme from below, the control points from above; pieces that cannot beat the best are dropped,
the others halved). A face whose trims run more than one turn round is no face of a cylinder: it
is refused as an invalid record, never kept as a spline.
The peg (40 x 16 x 10 bar, R8 end, a disc R8 extruded 10 up on its top, joined), front top edge
rounded r2: the body measures to 1e-7 of its closed form, the three r2 corner rounds after it
build and measure, and the upper wall comes back from SMLib a cylinder of radius 8 (engine test).
The rig case of the round of the edge where that round meets the wall (tangent at one end) still
fails, for another reason: on the wall as its exact cylinder SMLib refuses the round as larger
than the faces beside its edges allow (it fades to nothing at the tangent end) instead of
returning a body its own check refuses. Its KNOWN_FAILING line says so.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A curvature-continuous fillet (type curvature, equivalent radius 2) of the three edges at a top
corner of the owner's bar built, but its corner was SMLib's own patch, which is only tangent to
the rounds: Continuity Analysis measures a 35.8 / mm curvature jump across its seams (with the
rounds G2 to the faces everywhere else), and it shows as a dome sitting on the corner, the
vertical round's shading lost under it. All three edges were rounded; the corner was not
curvature-continuous, and nothing said so.
Such a corner, where three or more rounded edges meet, is now set back (1.5 r unless a setback
names it) and left open by SMLib with the curvature sections (smlib_blend_setback_open with
SMLIB_BLEND_CURVATURE), and filled with the G2 patch fillet_g2_corners already uses for circular
rounds (fillet_g2_with_g2_corners). The `corner` option no longer leaves a curvature fillet with
SMLib's patch: its corners are always G2, and setbacks on it set back the curvature rounds (they
were circular rounds before). Where SMLib or the patch cannot build it, it is refused.
On the reported geometry every seam of the rounds and the patch is G2 (rig
report-fillet-curvature-three-edges-at-bar-corner-solver-residues), and the rounds outside the
setback cube measure exactly: V0 - 27 - (the quintic section, A2 = 0.597884, along the front edge
from 3 to the wall and along 7 and 13) = 9541.116961 (...-outside-setback). With round coordinates
SMLib's open sheet fails its own check (a 2D curve cusp, SmBSplineCurve test 13): the fillet is
refused, listed as known failing (report-fillet-curvature-three-edges-at-bar-corner).
Test: corner_g2_tests::curvature_rounds_meet_at_a_g2_corner (box corner, r5: the patch's jump
under CURVATURE_SHARE / r clear of the hole's corners, SMLib's own patch over ten times that).
Changes a default: a saved curvature fillet with such a corner rebuilds with the G2 patch; there
is no preference or fallback to SMLib's patch.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A 220 x 11 two-distance chamfer of a tapered plate's bottom front edge (rig fillets/5181) runs up
the front face past its straight side edges, l2|start and l6|start, and takes them up: no result
edge comes from them. SMLib leaves the blend face untagged, and it was given every blended edge
whose two faces lie next to it: the picked edge l1|start and both taken-up side edges. Its name
came from the first in edge order, F3:blend:F2:side:l6|F2:start, an edge the user never picked.
A blend face now comes from the picked edges it lies between; only a face that lies between no
picked edge's faces (a corner's piece over a short edge the corner took up) comes from the
taken-up edges it lies between. The chamfer is F3:blend:F2:side:l1|F2:start everywhere on it.
Persistent names: a blend face that also lay between the faces of an edge the blend ran over is
now named by its picked edge only. There is no alias for the old name (5181's
F3:blend:F2:side:l6|F2:start): a saved reference to it is reported lost.
Also corrects 5181's "what": the chamfer builds (335399.749), it is not refused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The edge where a round runs into a cylinder's wall it is tangent to at one end (the bar's front
top round meeting the wall at (40, 0, 8), where the round's contact with the front face meets the
wall's tangent line with it) was refused as smooth, "nothing to round": the faces' normals were
compared at the edge's start alone, which was that tangent end. They are now compared at five
stations from end to end, and an edge is smooth only where its faces meet tangentially at every
one: this edge is a crease everywhere but its end. The wall's seam with the front face, tangent
all along, is still refused as smooth.
The round of that edge with its tangent chain (the top's concave arc) now reaches SMLib, whose
result fails its own check (internal poles, coincident control points, cusps where the round
fades out): its rig case in fillets is listed as known failing for that SMLib defect.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A round of a bar's top edge, where the bar's side runs tangent into a cylinder standing on its
round end, seemed to build: SMLib's result holds the cylinder's wall as a rational spline whose
parameter range runs 393° round (u in [-15, 40.18]). Going back into SMLib (to measure the body
or change it again) the record's extruded circles become SMLib cylinders with the face's range on
them, and that range was 6.866 rad: SMLib refuses a cylinder past one turn
(SM_ERR_INVALID_INPUT from BrepFromFlat's face range check). The body could not be measured, a
second round on it failed, and the app said one of its freeform faces can't be used. An extruded
circle whose range runs more than one turn round now stays the exact spline it is.
The bar of the reported design (40 x 16 x 10 with a R8 end, a disc R8 sketched on its top and
extruded 10 up, joined): the front top round removes the spandrel up to the cylinder's wall,
integral over y in [0, 2] of (2 - sqrt(4 - (2 - y)^2)) (40 - sqrt(64 - (8 - y)^2)) = 32.306475;
the three rounds at the other top corner after it remove 53.285832 in all (spandrels outside the
corner cube, the cube less the rolling ball's eighth). Both now build and measure to 1e-7; the
curvature corner of the three edges at once (setback 3) builds too.
Rig cases (fillets) for the three reports: the curvature corner of the three edges, the front
top round, and the three corner rounds after it pass; the same corner rounds with the design's
~1e-10 mm sketch residues fail in SMLib (its corner's surface of revolution is close to singular
at its boundary) and are listed as known failing. (Their ids take the report- convention in the
rig commit later on this branch.)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The shell unit tests that checked geometry become shell rig cases built through
commands: the trough and the pocket whose floors fall 1 deg to a central drain
(the pyramid made as two triangular prisms intersected, in place of
convex_polyhedron; the cavity integrated exactly over the cells where each moved
facet is highest, sharp inner corners as the ladder's tier 09), the box opened at
a bottom rounded R2 and R2.4 (refused: the rim would have no thickness) and R1.5
(built, exact volume), and the plate with a hole through its arc side. Four
action-matrix shells that regressed (issue-616's lid, the ring-cut frame, the
filleted shelled box shelled again, the up-down join) get small cases too. The
ones that fail today are on KNOWN_FAILING with their cause, and the unit tests are
removed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The fillet and chamfer unit tests that checked geometry become fillets rig cases,
built through commands with answers derived by hand (each method field gives the
derivation): a plate outline and a disc rim as tall as or past their wall, a
notched block's outline at R7 and R8, a cube corner as wide as its faces (refused,
and reduced), the 1668 wall at R7 alone and both sides, the 2852 U shell at R30
(refused, naming 25.24), the 851 knife edge (R2, chamfers 0.5/2/5 on three
constructions), the arc top edge at the full wall height and at 9.5, the 851
table of selections, the 556 top edge ending on the boss wall, the 2893
cylinder-rim chamfer refusals and the elliptical rim, seed 33's full round, the
sloped basin rim blends (single edges with exact volumes, loops with the slab's
box), and three action-matrix chamfers and fillets. fillets/851's three-edge
corner gets its volume (67.051 removed, re-derived on a grid; the engine test had
67.05). Chamfers whose leg runs off the face beside the edge are refused and rounds
past a face on its tangent side build, as the owner ruled on 2026-10-30. The cases
that fail today are on KNOWN_FAILING with their cause.
The unit tests are removed, except two cut to what no command can express: the
per-edge-radius refusal at a cube corner and the chamfer of a cylinder's seam.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A colliding pair past the 16 pairs whose volumes are worked out, or past
the check's 256 body intersections, or whose intersection could not be
made, fell back to the sampled mesh depth for its deepest step. That
changed what deepest_step means without saying so. Such a collision now
answers deepest_step and volume_mm3 null and not_measured naming the
budget it ran past (or the intersection that failed), as compare does
since #9132; first_step, last_step and steps are exact and stay.
B pushed through A at 1000 samples overlaps it at about 330 samples, past
the 256 intersections: not measured, "the check's 256 body intersections
ran out". At the study's 16 samples it is measured, deepest at step 15.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
motion.interference picked a collision's deepest step by the depth sampled
on the contact meshes (vertices, edge midpoints, triangle centres), and
worked out the exact shared volume only there. That depth depends on where
the mesh puts its points: since planes mesh as their boundary's triangles,
the arm turning into a block (rig case
assemblies/cov-motion-interference-arm-into-the-block) sampled 4.64 mm at 60
degrees and 2.0 mm at 90, and the check answered step 6 with 536 mm3. The
exact depth is 5 mm at every step from 60 to 90 degrees (both slabs are
10 mm thick), so depth cannot tell those steps apart.
The exact shared volume is now worked out at each sample a pair overlaps,
and the deepest step is the first with the most (a tie keeps the earlier
sample). The arm and block share 536, 807, 952 and 1000 mm3 at 60 to 90
degrees, so it is step 9 with 1000 mm3, at 10 samples or 19. depth_mm is
reported as before and documented as an estimate from the contact meshes.
volume_mm3 is null, and the step falls back to the sampled depth, when the
volume was not worked out at every sample (more than 16 pairs, or past the
boolean budget, raised from 64 to 256 now that it covers every sample).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
`inspect.curvature_comb` read the display mesh for model geometry: an
edge's comb fitted a circle through every three points of the nearest
mesh polyline, a face's did the same on its iso lines' chord points. The
comb was jagged, changed with the mesh tolerance and ignored `density`.
- geom: `CurveEval::jet`, a curve's point, unit tangent and curvature
vector kN from its first two derivatives (lines and conics in closed
form, B-splines and NURBS from the basis functions' derivatives, a
traced intersection from both surfaces' normal curvatures along its
tangent, by Meusnier: kN lies in the plane of the two normals and its
component along each is that surface's normal curvature).
- kernel (curvature_comb.rs): the edge nearest a pick by the exact
distance to its curve (a periodic face's seam and poles left out),
`density` teeth at even steps of the edge's parameter; along an iso
line, the surface's normal curvature n.S_tt / |S_t|^2 along its normal.
`IsoLine` carries the running surface parameter's span.
- engine: edges and faces use them (and `inspect.minimum_radius` on
edges); new optional `length` multiplies the automatic scale. The reply
keeps its shape.
Tests: a circle edge reads 1/R to 1e-9 at Coarse and Ultra display
quality alike, with `density` teeth; an extruded ellipse's edge matches
ab/(b^2 cos^2 t + a^2 sin^2 t)^(3/2) at every tooth, a/b^2 and b/a^2 at
the vertices; a cylinder face's rings read 1/R and its lines 0; `scale`
and `length` set the teeth's length; curve jets on every record kind.
The existing cylinder-edge check tightens from 0.5 mm to 1e-9.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ordinary_curved_bodies_keep_a_practical_sampling_step asserted
ContactGeometry.step > 1.0, an internal sampling step derived from the
bodies' display meshes. What a user gets is the drive: it either stops at the
contact or is refused for running out of the sampling budget. The test,
renamed ordinary_curved_bodies_stop_at_their_contact_within_the_sampling_budget,
keeps that: the slide drives to -30 without a budget error and stops in
(-5.02, -4.9) (the sphere r 5 about x = 20 and the box from x = 15 meet the
block's x = 10 side after 5).
It still fails on develop with "motion exceeds contact sweep collision
budget": the planar faces meshed as grids, which the planar-tessellation fix
(#9307) addresses.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
open_in_easyprint_hands_the_host_a_3mf_or_an_stl_that_reads_back asserted the
STL was 84 + 50 * 12 bytes: twelve triangles, the tessellator's count for the
fixture's box (the fixture is a mesh import of box_solid's display mesh, 124
triangles today).
The STL is now parsed (solidcraft_io::read_stl): it has the imported mesh's
own triangle count, every side is shared by two triangles running opposite
ways (closed and consistently wound), it encloses the 10 x 20 x 30 box's
6000 mm^3 (divergence theorem, to 1e-6; the corners are exact in f32) and its
bounds are (0, 0, 0)..(10, 20, 30).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
free_form_profiles_extrude_exactly asked for an ellipse extrusion of exactly
3 faces and a spline-and-line extrusion of at most 5: how many pieces the
kernel cuts a closed side into. It now checks that the sides are exact.
Ellipse a = 10, b = 4, extruded 5: area = 2 pi a b + 5 P, P = 4a E(e),
e^2 = 1 - b^2/a^2. By the Gauss-Kummer series, P = pi (a + b) sum_k
(binom(1/2, k))^2 h^k, h = ((a - b)/(a + b))^2 = 9/49: P = 46.026225191330
(a 200000-point midpoint integral of sqrt(a^2 sin^2 + b^2 cos^2) agrees to
1e-13). A = 80 pi + 230.131126 = 481.458538 mm^2, asserted to 1e-4; a faceted
side would be short of it. Only the top and bottom are planes
(face_types.plane = 2, merged pieces counted once).
The fit spline closed by a line: the planes are its top, bottom and the line's
side (face_types.plane = 3); its volume stays checked against the profile
area.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
a_mirrored_or_patterned_sheet_body_is_sheet_metal_with_its_flat_pattern
(1171c4c2a) expected the mirrored copy's model turned over: the same outline,
its bend down and its pocket on top. That describes a SheetBody::moved that
never landed. The code on develop is SheetBody::copied (d9d6af51c, #3354): a
mirror moves the frame and mirrors the flat x -> -x with the same thickness
side, the opposite hand's blank with each bend turning the same way, which
a_mirrored_sheet_copy_is_the_opposite_hand_with_the_mirror_image_flat_pattern
asserts on an asymmetric bracket. The YZ mirror keeps z, so a pocket cut from
below stays below and the flange on y = 0 still turns up: the flat pattern
reads blank x 0..100 -> -100..0, pocket x 20..30 -> -30..-20, side bottom,
bend up.
The test now asserts that: the same flat size, the outline and the pocket
outline equal to the source's with x negated (to 1e-6), pocket side bottom and
bend up on both. The volume doubling, the bend table and the flange rebuilt
on the copy (point containment) stay.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
a_trays_faces_have_readable_sheet_names_that_follow_its_size asked for
exactly two unnamed faces (the hole's wall in two halves) and for the back
rim's named point at y = 199.5, the strip's centre line. The first is how many
faces the kernel makes a cylinder of; the second is where the face's roomiest
display triangle lies (naming::face_spot), any point on the face.
Now: there is an unnamed face and every one is the hole's wall (r 3.3), and
the back flange's far rim point lies on that rim: z = 30 and 199 <= y <= 200
(the flange 1 thick, its outside at y = 200), 0 <= x <= 400, to the 1e-3 the
test had. The right flange's top (the plane x = w - 1) keeps x = 319 and 399.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillet_the_knife_edge_at_the_tip (features_more_tests.rs) and
blend_a_knife_edge_where_a_curved_wall_runs_out (tests/robustness.rs) build
the same #851 part with the same script, round the same knife edge at
(62 1/6, 0, 5) with R2 and measure the removed volume through the same display
plan. The first integrated the removed area on a grid (5e-4); the second has
it in closed form. Drop the first and keep its tolerance on the second.
The ball 2 from the back face y = 0 and from the r 21 wall about (62 1/6, -21)
is centred at (62 1/6 - sqrt(168), -2). The removed section is the trapezoid
wall centre, tip, (kx, 0), ball centre (sqrt(168) wide, 21 and 2 high) less the
wall's sector theta = acos(19/23) and the ball's sector pi - theta:
10 (11.5 sqrt(168) - 220.5 theta - 2 (pi - theta)) = 119.648812 mm^3
the constant the kept test has; the dropped test's grid gives 119.6487 at a
0.004 x 0.001 step. The kept test's fillet bound goes from 0.5 to 5e-4 of
that (0.0598), the dropped test's. Its chamfer row (159.236451, the chord
triangle less the wall's segment) already says the chamfer takes more.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
cut_whose_end_touches_an_arc_side_leaves_no_sliver compared the touching cut's
face count with a clear cut's, a count of how the kernel splits its faces. It
now compares what the two parts are.
The plate's arc runs from (0, 20) through (-10, 10) to (0, 0): centre (0, 10),
r 10, so it reaches x = -10 only at y = 10. The r 5 cut along x about
(y, z) = (12.5, 12.5) spans x -10..7.5 (touching) or -10.1..7.4 (clear). Both
open the same patch of the arc; the slice x 7.4..7.5 lies wholly inside the
plate (y 7.5..17.5, z 7.5..17.5 in 0..20 x 0..27.5). So
V(clear) - V(touching) = pi 5^2 0.1 = 7.853982 mm^3
A(touching) - A(clear) = 2 pi 5 0.1 = 3.141593 mm^2 (the hole wall; the
floor disc is the same)
both to 1e-4 (the measure integrates the exact faces to 1e-8). A sliver of the
arc left where the end touches adds about a square millimetre of faces.
Seed 14's half (the fuzz generator's seed, then a shell) is pinned as its own
test, shell_after_a_cut_whose_end_touches_an_arc_side, with the commands the
generator gives today: the touching cut, then a 2 mm shell opening the top
face y = 20. It fails at the shell (SMLib status 1001), a kernel gap.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Stale since 84bd2daad, which gave solid.fillet each pick's tangent chain by default. After the
long top front edge is rounded, the front-left upright meets the round's end (the quarter circle
on the left face) along its tangent, and that circle meets the top-left edge along its tangent:
the second fillet rounds the upright and the top-left edge. The "together" fillet picks the
three edges ([20, -21, 10], [0, -21, 5], [0, -10, 10]); one by one and together remove the same
volume within the display meshes' 2e-4 (it read 60.649 vs 43.185 with two picks).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The test offset the sphere's top patch to get a fitted B-spline sheet. That held on truck,
whose sphere came in several patches and whose sphere offset was fitted. On SMLib the
sphere is one face: offsetting it closes up, so it is a solid by design (surface_offset.rs,
"Faces that close up make a solid", and its test a_sphere_is_fitted_and_refused_past_its_centre
asserts exactly that), and SMLib's offset is exact, a sphere of radius 22 with no control
points, which surface.fair refuses. Body::is_surface was right: the record lists the offset's
closed shell as the outer shell of a material region (Parts::canonical), so it is a solid
whether read from edge uses or from regions.
The test now fairs the patch on the non-planar rim of a box cut by a sideways cylinder (the
cover in patch_trim_thicken_and_stitch), a one-face B-spline sheet: energy 0.7185 → 0.6938 in one
step, edges unmoved bit for bit, undo/redo/reopen and the refusals as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
hostile_params_never_panic built a box, a sketch and a rectangle afresh for each of the ~3000
calls it makes per command. SMLib serialises every call behind one process-wide lock, so those
boxes were built one after another whatever the number of threads: 20 threads made 4000 boxes
in 7.8 s, one thread 200 in 0.31 s (1.5 ms each). The fixture was nearly all of the test's time
(8814 of 8823 thread-seconds over the first 72 commands on the aarch64 box; the commands
themselves 9 s, none over 0.5 s), and the test took 2195 s in develop CI.
It now builds that model once per command and gives each call a copy of the session with its
design, model, undo, redo, open sketch and log, sharing the bodies as undo does. Every command
still gets every parameter name with every hostile value, from the same starting state. A new
check runs Cancel Sketch, two undos and a redo on a copy and on a session built afresh and
finds the same designs, with the copied session untouched.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>