* Fillet fit: a round counts only what lies between its edge and its arc
The fit check refused a round when any other face of the body reached into
the wedge between its edge and its two setback lines. A round changes only
the part of that wedge between the edge and its arc: a face on the ball's
side of the arc is left as it is. An outside round concentric with the
inside round of a 3 mm wall (R18 over R15) was refused as too large
(largest 14.21 mm) although it keeps the wall 3 mm thick.
The face check now tests a round's fan of prisms from its edge to its arc
(Frame::pieces, already used for blends that cross), after the wedge as a
quick filter. Chamfers keep the wedge, which is what they change.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01L15TLCjpXsQdp8ovC4ZacH
* Fillet fit: a curved face clears a round's thin end pieces only by a chord (#324)
The fan test shrank each piece by the curved faces' tolerance; the thin pieces at the
arc's ends vanished, so a hole wall 0.3 mm into a round beside it was missed and the
round failed to build instead of offering the radius that fits (issue_324_tests).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* claim: #3001
* fix(ui): Convert Mesh asks for the mesh body and its tolerance (#3001)
It had no dialog, so the toolbar ran mesh.convert with no body and it always
reported "select a mesh body". A dialog now takes the mesh body (a selected one
fills it) and the tolerance.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #2943
* fix(update): release-note links open in the browser (#2943)
The notes kept a link's text and dropped its target, so the blue text could not
be clicked. Links keep their web address, and each paragraph or item is
followed by its links as buttons that open them, as the agent chat shows links.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #2823
* fix(view): lines thinner than a pixel no longer vanish without multisampling (#2823)
A line quad narrower than a pixel covers no pixel centre when it falls between
two rows, so the grid's 0.7 px lines came and went as the view zoomed where the
viewport draws without 4x MSAA (some browsers and devices). Such lines are now
drawn a pixel wide, faded by the width they lack.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #2700
* Two-sided extrudes: the second distance goes the other way from the first side, either way round (#2700)
extent_sides ignored `direction` when an extrude had `distance2`, so through all with
`direction: negative` and a second distance went the positive way. The second distance now goes
opposite the first side wherever that went (direction: negative, a negative distance, a To
Object below the sketch). A pending format step makes older designs' reversed two-sided
extrudes positive, which keeps their shape.
The Extrude dialog's Two Sides shows Distance 2 for every extent type (it was hidden for All and
To Object but still sent as 10 mm) and offers Reverse; the second arrow points the other way
from the first.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* The two-sided arrows test checks each tip against the sketch, not just their order
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #2592
* fix(agent-chat): the design bridge is named solidcraft-app (#2592)
A user's own MCP entry named `solidcraft` (as docs/mcp.md suggests) took the
bridge's place in agents that keep their own entry on a name clash, so the chat
worked on a headless session instead of the open design.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
On Windows, Git's default core.autocrlf checks the icon masters and the
palette out with CRLF, and `cargo xtask icons` failed four ways:
- the accepted-icon hashes (lint_icons.py and the review page's
review_state.master_hash) were taken over the files' bytes, so every
accepted icon read as changed; both now use master_hash, which hashes
the text with CRLF read as LF;
- icon_palette.revision hashed the bytes while save_colours hashed the
text it read, so every palette save was refused as stale; revision now
reads the text too;
- the tools and their tests read and wrote text in the locale's encoding
(cp1252 can't write U+2194); they now say utf-8;
- the icon inventory listed UI files with backslashes; it writes /.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* Bill of materials: part properties on components and assembly.bom
A component definition now carries part properties (part number,
description, revision, other tools' keys) and free text properties,
saved with the component and shared by its occurrences.
component.metadata and component.metadata.set read and change them in
one undo step; Paste New copies them; parts.insert numbers standard
parts from their standard and size, and parts.resize renumbers them.
assembly.bom counts the placed components (flat: parts at any depth
through their subassemblies; top: direct children), grouped by part
number or by definition, sorted by part number, and writes CSV (fixed,
quoted columns) or JSON. The app gets a Bill of Materials window on the
INSPECT panel that lists, edits and exports the rows.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Bill of materials: name a merged row's equal definitions once
Two standard parts with the same size are separate definitions with the
same name; their row now reads "SHCS M6x20" instead of repeating it.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Window widths test: close the Bill of Materials window between commands
The test closes the floating windows a command opens before starting
the next one; the Bill of Materials window was left open and measured
against the next dialogs' limits.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Bill of materials: sub-parts in their part's row, and part properties without re-evaluating
assembly.bom takes group_children: true. A part with a part number keeps
what is placed inside it (a bolt's washer and nut) in its own row, listed
under it as children (items 1.1, 1.2, with each and count) instead of rows
of their own; bolts with different contents stay different rows, and
total_occurrences is the same either way. The window has a switch for it
and shows the children under their part; the CSV lists them after their row.
Changing part properties re-evaluated the model, re-seated every joint and
rebuilt the placed model: 361 ms per change with 30 jointed bolts. A change
that only touches components' metadata and properties now takes the same
path as a render-only change (proved on the whole Document), also for its
undo and redo: 0.6 ms.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Bill of materials: look the structure up once, not per subassembly
Deciding whether a subassembly is a part (it has bodies of its own) scanned
every body of the model for each subassembly, and each body looked up its
feature by a linear search of the timeline: subassemblies × bodies × features.
assembly.bom now indexes the placements, the body owners
(Document::body_owners: one pass over the bodies with the timeline in a map,
the same rule as model_body_component) and the numbered components once per
call. 600 bodies and features with 60 subassemblies: 8.1 ms → 1.3 ms; the
old cost grows with the cube of the design's size.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* Centralise tool modifiers with classic defaults and preview-safe Ctrl.
Route sketch/selection chords through a shared resolver. Keep Alt snap
suppress and dual toggle as defaults; optional Shift add-only and Ctrl
snap mapping. Skip preview rollback while a manipulator drag is active.
* Address #1616 review: classic snap suppress, single viewport owner, docs.
Default suppress to Ctrl/Cmd or Alt; drop navigation set_suppressed; remove unused label_key; add preview rollback gate test; document sketch modifiers.
* fix(#1616): correct Modifiers primary in tests; simplify rollback fixture.
* Treat Ctrl as primary off macOS, and rustfmt the modifier files.
* kernel: trim keeps picked regions, mutual trim, curves swept along a direction (#767)
Trim moves to surface_trim.rs: TrimKeep::Side (the old behaviour) or
Regions (the connected pieces the points pick, parted where the tool runs
along an edge). mutual_trim cuts two one-face surfaces by each other's
surface, extending one that stops short when asked. SplitTool::Curves takes
a sweep direction; a closed curve's field is signed by inside/outside
instead of extending its end segments.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* kernel: classify display edges of a face with a closed-edge hole without a panic
A hole cut by a closed curve is a loop of one edge that starts and ends at
one vertex; mapping the face rebuilt that edge through a check that
panics on it (the guard caught it and dropped every smooth flag of the
body). Such faces are now left out of the ruled-surface test.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* surface.trim: keep several regions, trim by projected sketch curves, mutual trim (#767)
keep takes a list of points (the regions they pick); curves: {sketch,
curves?, direction?} sweeps sketch curves onto the surface (along the
surface's normal: not supported yet); with + keep_with trims two
surfaces by each other, extend? meets a short one, stitch? sews the
kept pieces. Trimmed faces carry their lineage, so they are named
after the faces they are pieces of. New fields noted in a pending format file.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* Trim dialog: sketch curves as the tool, several keep points, mutual trim (#767)
The tool input takes sketch curves too; keep points are places (several
on one face add up); another surface with its keep points makes a mutual
trim with Extend to meet and Stitch toggles. Edit Feature brings it all
back. Labels in every locale catalog.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
* ROADMAP: M8 trim by projected curves, several regions and mutual trim (#767)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LGeCa5jWWdroMWvXxN3LLM
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* Sketch points placed by expressions over the design's parameters
A point typed as an expression ("W", "H / 2") in sketch.point, sketch.line and
the other point arguments is fixed where its expressions come to, and moves
there again before each solve when the parameters change: an outline that
follows its parameters needs no dimensions and no solve per change. The
expressions are saved with the point (one pending design-format change), listed
with the sketch's other expressions, and renamed with their parameters; one
that cannot be worked out is refused.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* Sketch point expressions: accurate params doc, out-of-range regression test
The sketch.line params said every point argument takes expressions; only those that
also take a point id do (the rectangle corners, an arc's through point and the like
are plain [x, y]). PointExprs' comment called its expressions mm. A test covers a
parameter that puts a placed point out of range and a design file whose point
expression overflows: both are errors, not crashes, and the sketch recovers.
Co-Authored-By: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
assets/locales/ belongs to no crate, so affected.py selected the full
workspace (every crate, all four test shards) for a catalog-only PR. Only
solidcraft-ui-egui embeds the catalogs and xtask checks them; map the folder
to those two packages and their dependents.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The window listed (and so evaluated) every parameter and re-checked the add row's
expression on every frame, and laid out every row. It now lists once per design
revision, caches the add row's check, and lays out only the rows in view.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The chat in a window of its own takes the files dropped on it and shows the drop hint while files are dragged over it; a window floating inside the app counts as the chat's place for the app's drop handling.
A PDF goes whole to agents that take embedded documents; to the others, or past 12 MB, the message names it with its type, size and place. Any file that is not a picture, text or CAD file is attached by reference instead of refused. Chips show the type's extension; the file dialog offers All files.
Files copied in the file manager attach as files, a picture on the clipboard attaches as a picture, text pastes as text. A picture-only or files-only paste is seen through the V key coming up (egui-winit sends nothing when the clipboard has no text); macOS sends no key-up while Cmd is held, so there only pastes that come with text are seen and + > Paste a picture still works.
* CI: heavy checks run after review (approved-for-ci label)
Pull requests without the approved-for-ci label run Select checks, the
format and repository checks and a quick cargo check. The label runs the
full suite, and every push after that does too. Other labels start no work
and never cancel a run. Main, merge groups, nightly and Run workflow are
unchanged.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* CI: approved fork PRs run heavy jobs on self-hosted-fast in private directories
An approved-for-ci label on a fork pull request sends Clippy, Build tests,
the test shards and Doc tests to the trusted runners, with private copies
of the build directory, Cargo home and rustup home that are deleted after
the job. Only the labeling event qualifies; later pushes use the old fork
routing. The skipped run of an unrelated label names its ci job differently.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
* Revert "CI: approved fork PRs run heavy jobs on self-hosted-fast in private directories"
This reverts commit 439f2f7dab.
* CI: name the ci job differently on an ignored label's skipped run
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>