fillets/4782-fillet-two-end-verticals-past-a-full-round passes: SMLib (90aabff) refuses
R10 on the 15 mm wide box's two end verticals as too large, and the refusal now names
the largest radius that fits, 7.5 mm (the full round). Run on aarch64 Linux with
--known-failing: every other fillets case as listed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Which input plane each result face lies on was found by scanning every input plane whose
normal x was within the resolution's angle: quadratic on axis-aligned parts (two thirds of the
faces have normal x = 0), so it was capped at 16 384 faces a body and 2 M comparisons, and the
join of the 20 level-2 sponges of a level-3 Menger sponge (7 326 faces) was refused past the
comparison budget.
The planes are now indexed by their unit normal, in cells twice the bound on two matching
normals' difference (asin(angular) < 2 angular), and in each cell by their offset from a common
centre, searched in the window linear + |a.o - c| |n_b - n_a| that
d_b - d_a = (b.o - a.o) . n_b + (a.o - c) . (n_b - n_a) gives, plus rounding slack. The index
offers a superset; same_support still decides each match, and candidates are taken in the same
order as before, so every answer is unchanged. A plane with a normal not of unit length is
offered to every query. Both caps are removed: results are bounded by inputs capped where they
entered. The descriptor-size budgets on kept roles are unchanged.
Rig, --known-failing, results compared case by case with develop's: booleans (129) and shell
(28) identical except booleans/5126-join-menger-sponge-level-3, which now passes in 38.9 s on
aarch64 and leaves KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
explode.show put the view's placements in the uncaptured moves, so occurrence.properties reported
the exploded placement and Capture Position (and reparenting, moving bodies between components,
copying or pasting in place, URDF export) wrote the view's offsets into the design. The session
now records which uncaptured moves are the view's (Session::exploded); what reports the design's
placements or works a new placement out from them uses the design's own moves
(uncaptured_moves, design_document), while the viewport and picks still show the view.
New case cov-explode-show-keeps-the-placements: the arm's properties are the same before, while
and after the view is shown, and Capture Position keeps nothing. The two explode cases that read
occurrence.properties while exploded now expect the design's placement, centre (20, 0, 5), as the
command says ("shown only; the design keeps its placements").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The curves were held on a 1-2-5 ladder from the world origin, so count 3 on a 40 x 30 face gave 3
one way and 2 the other. They now follow the command's contract: the held parameter at
lo + k (hi - lo) / (count + 1), k = 1…count, over the face's extent. Faces of the body on the same
surface record are spaced together over their combined extent, so a face a boss splits still
shows the same lines straight across the split.
New case cov-isocurve-40-by-30-face-count-3: x = 10, 20, 30 and y = 7.5, 15, 22.5, to 1e-9 mm.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Both walked the picked curve's display polyline: a point a third along an R10 sketch arc was
0.87 µm off (8.6603, 5). They now evaluate the path's exact curves by arc length: lines and arcs
in closed form, a free-form span at the parameter its arc-length integral reaches (body edges by
their record curves, 3D sketch curves by their arc, spline, line or linked exact curves; only a
curve that exists as points alone, an intersection edge or a projected curve, runs along them).
The arc's point is now within 1e-12 mm of (10 cos 30°, 5, 0).
A t outside 0…1 was clamped silently, which the contract (`t: expr, 0…1 along it`) does not
say: it is refused ("t is 1.5: a point along a path is 0 (its start) to 1 (its end) of the way
along it"). The construction cases grade the arc and line to 1e-9 mm, past-the-end is refused,
and a new case takes the middle of a symmetric cubic spline, (20, 7.5).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A face of degree 1 in one direction (an extruded spline) was refused with "a fairness term does
not fit the net's degrees": the thin-plate energy's S_vv asks for second derivatives a linear
direction does not have. On every span that term is exactly zero, so it is dropped; the energy is
the bending along the curve and the twist. A face whose held layers are its whole net (a
single-span cubic with its edges kept, an extruded curve's two rows) has no interior control
point: it is left exactly as it is, its energy reported unchanged, 0 steps.
cov-fair-single-span-face-has-nothing-free-to-move passes and leaves KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Where a round meets a plane it is only tangent to it: its curvature jumps by 1/r there, so no
corner patch can be G2 to both at that point. The cases graded the whole seam and could not pass.
They now bound the curvature jump at stations clear of each seam's turn, within reach of the
corner, scaled by r (ladder 07/019's bound at r5): r1 within 2.2 mm, 0.24 mm clear, 0.005 per mm;
r5 within 11 mm, 1.2 mm clear, 0.001 per mm. Develop's corner gives 0.00135 and 0.00027 per mm
(the jump at the vertex is 1.017 and 0.2035, the round's own 1/r), so both leave KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
inspect.compare integrated a region's volume along sampling lines: the
40 x 30 x 5 slab between a box and one 5 mm taller came out at 5976.49 mm3
against 6000. The regions are still found from the two surfaces; each one's
volume, centre and box now come from the pieces of the exact cut a - b (or
b - a) that lie there, measured as inspect.measure measures a body
(measured_by: boolean). Where a cut cannot be made the region keeps the line
integral, marked measured_by: lines, with a warning. The rig case
cov-compare-taller-box passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
inspect.center_of_mass measured each body's display mesh, so a cylinder r 5,
h 10 came out at 784.13 mm3 against 250 pi = 785.40, and the answer moved with
display quality. It now takes the exact mass properties inspect.measure uses
(ModelBody::measure), skips bodies that enclose no volume as Measure does, and
lists what it skipped. The rig case cov-center-of-mass-box-and-cylinder passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- #58: a fillet's tangent-point step no longer depends on the blends before it (solidcore #1173).
- #59: the fillet clean-up keeps the target's edges and faces by a mark, not by address (#1176).
- #60: capi test, a line projected through a sphere's poles meets itself smoothly at each pole.
- #61: offset faces removes a step wall the move closes to nothing and merges the two tops, so
shell/cov-replace-face-step-onto-the-higher-face builds.
- #62: thicken puts a flat side wall on its plane (solidcore #1599), so a cylinder sheet's end
rings are planes: surfaces/cov-thicken-cylinder-sheet-symmetric-tube passes.
Both cases leave KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The single results form compares a whole number exactly (a count). The construction and inspect
cases gave positions and volumes as whole numbers, which the form they were written for compared
within tolerance; they are decimals now. The NPT groove fix makes ladder 06/023 pass: its golden
entry is the passing run (51 faces, 8226.4042 mm3).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The shared core (crates/smlib, the grader, doc eval.rs, engine features.rs and the kernel's core)
is in PATHS-ALL; the new areas' copies of it are dropped, so an area reruns on its own files and the
core reruns them all. sheet-metal also watches the sheet commands, the sheet document and the DXF
writer. 116 commands a case now uses leave EXEMPT; 25 geometry commands are still to cover.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Two branches added a results field in different forms ({step, json} and {command, pointer,
value}). The grader keeps one: a 1-based step, an optional JSON pointer into its answer, and the
value matched as files are, with an optional relative or absolute tolerance. The construction and
inspect cases are rewritten to it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
167/168: every new case passes against its hand answer but 06/023 (1/2-14 NPT external), whose
groove stops 0.015 mm past the crest at its section's middle, under the crest cone on the section's
deeper side, so a sliver of each tooth's flank stays (0.94 mm3, 1.1e-4). The 139 cases before keep
their statuses and counts; their volumes and areas re-measure within 2e-6 on this SMLib.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Base flange; an edge flange at 90 deg; four made together, the corners closed on the mitre plane
with the rule's gap, at 90, 72 (leaning out, the ends run on along a slant) and 108 deg (leaning
in, cut back); round, rectangular and tear reliefs; a hem; a fold, unfolded and refolded; the
tray's flat pattern (outline size and area, bend lines); a bracket with a hole and a flange on a
flange. K = 0.5, so every volume is T x the flat area. The 108 deg tray is a sheet-metal rig case too.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
From the script's last sheet.flat_pattern result: the outline's size, its area less the
cut-outs', and the bend lines, each matched to its own one of the result's either way round.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
G 1/2 external and Rp 1/2 internal (ISO 228-1 / ISO 7-1, 55 deg) by Pappus turn by turn; R 1/2
and 1/2-14 NPT external and Rc 1/2 internal tapers (1 in 16 from the standard's diameter at the
free end, crests cut by the major or minor cone) by the screw sweep's Jacobian, integrated exactly
(ladder_lib.sweep_removed); an S20x4 run down to a shoulder with its steep flank toward the end and
toward the start, which moves where the groove stops; tip: start, and a Tr20x4 chamfered at its own
30 deg and 2.5 mm; refusals for a Tr chamfer without a depth and for the square form.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
1/4-20 UNC (#7, 0.201 in) and Rc 1/2 (17.6) through the stock, 1/4-28 UNF (5.45) blind with a
flat floor, 1/4-18 NPT (10.85) through: a cosmetic thread in a straight hole, so each volume is
the stock less that cylinder. The drills are the catalogue's (Guhring, Yamawa YEU23); each method
gives the standard's minor diameter beside it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A Default row, a 60 mm row, a row without the hole, a height column and rules
that suppress the hole or drive the height, each checked after activation;
preview leaves the design; refusals for a row that cannot build, unknown rows,
columns and features, and a rule a row breaks.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Suppress a hole and the block is whole again; a round moved before the notch
runs the whole edge and is cut by it; deleting a sketch takes its cut and
deleting the block leaves the round and cut failing; roll to the middle gives
the part at that step; edits, compute all and folders, each with a refusal.
The new history area has its KNOWN_FAILING (every case passes) and PATHS.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>