a_round_into_a_hole_is_cut_by_it (issue_324_tests.rs) built rig case
fillets/324-fillet-over-hole-overlap's body, but cut its hole with a cylinder
longer than the block (z -1 to 11) where the rig extrudes a sketch circle
flush. The new case fillets/324-fillet-over-hole-cut-by-overlong-cylinder
builds it that way (solid.cylinder, base z -1, height 12, cut) and holds it to
the same hand-derived answer: block 40x20x10 less the r3 hole at (20, 14.5)
(282.74) less the R4 round on the top edge at y = 20, 40 (16 - 4 pi) = 137.35,
plus what both remove, the integral over y in [16, 17.5] of
(4 - sqrt(16 - (y - 16)^2)) * 2 sqrt(9 - (y - 14.5)^2) = 0.375830 (re-derived
with the substitution y = 17.5 - s^2, 200000 steps):
V = 8000 - 90 pi - 40 (16 - 4 pi) + 0.375830 = 7580.287315, and G1 on the
blend. It passes today (aarch64, SMLib), as the flush case does, so it needs no
KNOWN_FAILING line; the unit test, a duplicate of the two cases, is dropped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A box edge chamfered 2 and by two distances (3 and 1, and flipped, told apart by the
centre of mass); a pocket's rim chamfered 1, by two distances, 4.9 (fits), and 5 and
5.5 (refused by the owner's rule on full-width chamfers: built at 5 today).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A box edge rounded, then the edge meeting it at the corner, in both orders (both the
three-edge rolling-ball corner); r3 then r2 (the r2 round's torus about the r3 round's
axis, by Pappus); an L-bracket's front inner outline after its bend round; a block's
top edge after the arc round at the cylinder (fails today: G0 at the round's end on the
crease); a curvature round after a curvature round with Tangent chain off.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Inside bend r3, outside r5, both concentric (r3 and r8), the inside r35 using up both
inside faces, r36 refused naming 35, and the inside bend Type: Curvature.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Top and both rims rounded r1 and chamfered 1; the top rim rounded r10 (as deep as the
plate), r12 (past it on its tangent side: built by subtraction, fails today with
status 1001) and Type: Curvature; chamfered 9.9 (fits) and 10 (the full depth:
refused by the owner's rule, built today). Volumes by Pappus.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A rectangular pocket's floor edges, rim edges and both rounded r2, the rim r5 as deep
as the pocket; a boss's root r2 and r10 (as tall as the boss) and its top rim r2.
The rim cases fail today: SMLib puts a corner patch where two rim rounds meet at a
concave pocket corner, where the rounds running into each other make a mitre (four
faces more; the volumes agree to 5e-4).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A block whose sides meet the cylinder at creases: the concave arc at the wall above
the block's top r2, the cylinder's top rim r2, the block's long top edge r2 with
Tangent chain off and Type: Curvature. A block as wide as the cylinder, its sides
running tangent into the wall: the arc and the long top edge each rounded alone
(built or refused as continuing tangentially). Volumes by Pappus or one-dimensional
quadratures of the exact sections, the round ended by the planes it runs into.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Three edges at one box corner rounded r1 and r3 with the rolling-ball corner, r3 with
Corners: Curvature at its default setback and at 3.5, and refused at 3 (the radius);
the corner chamfered 2; all twelve edges rounded r2; one edge rounded Type: Curvature.
Volumes in closed form (strips plus sphere octants, half-space intersection, the
rounded box as a Minkowski sum, the quintic section's area 113/756 s^2); G1 at every
round's seam, G2 for the curvature round and the corner patches.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillets/4782-fillet-two-end-verticals-past-a-full-round passes: SMLib (90aabff) refuses
R10 on the 15 mm wide box's two end verticals as too large, and the refusal now names
the largest radius that fits, 7.5 mm (the full round). Run on aarch64 Linux with
--known-failing: every other fillets case as listed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Where a round meets a plane it is only tangent to it: its curvature jumps by 1/r there, so no
corner patch can be G2 to both at that point. The cases graded the whole seam and could not pass.
They now bound the curvature jump at stations clear of each seam's turn, within reach of the
corner, scaled by r (ladder 07/019's bound at r5): r1 within 2.2 mm, 0.24 mm clear, 0.005 per mm;
r5 within 11 mm, 1.2 mm clear, 0.001 per mm. Develop's corner gives 0.00135 and 0.00027 per mm
(the jump at the vertex is 1.017 and 0.2035, the round's own 1/r), so both leave KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A plan job (scripts/ci/kernel_rig_plan.py, with its self-test) maps a pull request's changed files
to the areas: tests/kernel-cases/<area>/PATHS for each area, tests/kernel-cases/PATHS-ALL for the
shared core, the ladder whenever any area runs. Areas come from the folders, so a new one needs no
workflow edit. Pushes, merge groups, the release gate and runs by hand run every area. The
kernel-rig check counts a skipped build or shard as passed only when the plan selected none.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
With SMLib integration-overnight + b78bd4a (the fixes of 2026-10-29), three
expectations that held a refusal now build, each checked against its exact answer:
- rig fillets/1207-fillet-box-end-edge-into-unblended-round (was ...-refused): the end
face's top edge of a cube rounded r3 along its top back edge, rounded r1 alone
(tangent chain off), builds. Its round runs on along y through the r3 round's end
until that surface drops below it at y = 17 + sqrt(5): V = 8000 - 20 (9 - 9 pi/4)
- 17 (1 - pi/4) - 0.218236 = 7957.505202 (the last term the section under the round,
integrated exactly); SMLib gives 7957.505245.
- blend_smlib smooth_edges_and_unfinished_tangent_chains_are_refused_saying_why: the
same cube builds, at that volume.
- modify_history_tests::smlib::draft_tilts_a_side_and_keeps_its_name: the rod's side,
a cylinder along the pull, drafts 5 deg to a frustum, radius 5 at the neutral plane
and 5 - 10 tan 5 deg at the top, at its exact volume.
tests/kernel-cases/fillets/KNOWN_FAILING drops 1557-fillet-vertical-corners-after-
bottom-rounds, which passes now; the other eight still fail, so the gate holds
(81 pass, 8 known failing, no regression).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Ten cases the pin fixed leave the list (the 1207 corner patch and its together cases, 1390,
4782 reduce-fit, 896). 1557 joins it with its cause: since bodies are read back from their
records (#8625) its bottom rounds come back as SmCylinder where SMLib's blend made SmCone(0),
and the corner-ball trace starts 2.78e-4 off; its fix is in progress.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
New: an r5 curvature corner at a box corner (its patch must seam G2), an
edge running tangentially into a round left out (refused: continues
tangentially), a convex r10.01 round 0.01 past a 10 mm face (built by
subtraction: V = 7139.875, A = 2585.140). The bar and boss arc rounded
together say their crease (15.6 deg r2, 13.1 deg r1); 1390 expects SMLib's
unsupported-corner refusal, the honest reason today; past a full round
the exact fit's refusal names the largest radius that fits, 7.5 mm.
KNOWN_FAILING lists the 18 of 89 fillet cases failing today, each with
its cause.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
expected.json may give `continuity: {order: g0…g4, edges?: "blend" | "corner"}`: the
seams of each round, chamfer face or corner patch with the faces either side of the edge it
replaced, and of each corner patch with its rounds, are measured as Continuity Analysis
measures them (seam_diagnostics at its default 33 stations and default tolerances), and the
case fails naming the worst seam, its faces, the order it reaches and the next order's worst
value. The seams come from the faces' persistent names (doc::naming::blend_seams). The older
`{near, within_mm, …}` form is kept.
Every fillet-area case with a body gets its order: constant rounds and rolling corners g1,
curvature rounds g2, chamfers g0, the corner: g2 patch g2 at its seams.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A corner setback must reach past where the corner's rounds' contact lines
meet without one (smlib_blend_setback); short of it SMLib failed with its
own status (1001). The kernel now refuses it before SMLib runs, for the
rolling-ball corner (fillet_setback) and the curvature corner
(fillet_g2_corners) alike, naming the least: on each face at a corner of
planar faces and straight edges the two rails, r tan(psi/2) from their
edges, cross (d2 + d1 cos alpha) / sin alpha along an edge (r on faces
square to each other). Other corners stay SMLib's to refuse.
The rig's `refused` cases now name the reason (`refusal`, a part of the
message, required), so a failure for another reason no longer passes; a
`solid_or_refused` case may name one. Fillets: the setback cases and
783, 3435 pass; 1390, 896, 4782 past-a-full-round and the no-tangent-chain
case are refused for an unclear reason and fail.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
22 hand-written cases in tests/kernel-cases/fillets:
- 1207-fillet-bar-top-edge-and-boss-arc-together (r2, r1, fit reduce,
fit taper, curvature corners): a bar's top edge and the partial base
arc of a boss standing out over the bar's side rounded together. The
rounds' volumes away from the corner, the corner patch within (2r)^3.
SMLib's 3x2 mixed corner fails here (1001) until the fork's fix.
- 1207-fillet-bar-top-edge-after-boss-arc-round (r2, r0.5, no tangent
chain): the edge rounded after the arc; r0.5 fails SMLib's check.
- 9-fillet-corner-*: setbacks not past the radius refused (rolling and
curvature corners), the curvature corner at r1, and the curvature
corner with reduce and taper fits (not supported yet).
- 4782-fillet-*: full rounds (two end verticals at half the width, exact,
reduce, taper), a round at half the wall, radii past the full round
(refused; reduce gives the full round) and a round wider than both
faces (built by subtraction).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib now builds a round or chamfer whose rail runs off its face across a cliff (an opening's
rim, the body's outline): the blend is made as if its faces continued and what it removes is
subtracted, so it never bridges an opening (owner decision for rig 5158/5181; fork commit
"SMLib, capi: a convex blend overflowing a cliff is subtracted from the body"). The tests that
expected a refusal for such blends now expect the body, each answer from the geometry:
- variable_radius_on_a_box_edge: 2 -> 50 on the 10x20x30 box's top edge builds at
3546.18767939 (circular sections in y = const, the r x r square less the quarter disc,
clipped to the box; rel 1e-4).
- variable_radius_from_a_spline: the "big" law builds at 6000 - 726.5334566720 (de Boor law,
split at the knot and where r crosses 10).
- a_chamfer_meets_sloped_end_planes: chamfer 25 removes 11500 - 4625 * slope
(integral of 40 - 2 * slope * y over z >= y - 5).
- g2_fillet_refuses_invalid_geometry: G2 at 25 builds at 6138.1606889 (the quintic section
with control points at thirds, clipped to 20x20, along 20).
- fillet_max_each_reduces_only_where_the_radius_does_not_fit: both edges take 4, 24438.7317761.
- hostile_inputs_are_errors: chamfer 30 on the cube builds at 1000 (y + z <= 10 along 20);
R50 still fails.
- kernel-cases fillets/1080: the 9 mm chamfer into the openings builds at 3350
(method in expected.json).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_0113gDVmStT5tCGKW9Fxgc5K
Cases from the issues filed after #4160, each a synthetic recipe with its own answer
(analysis or invariants); every other issue in the range is listed with why it was skipped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Cases from the issues filed after #4160, each a synthetic recipe with its own answer
(analysis or invariants); every other issue in the range is listed with why it was skipped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Cases from the issues filed after #4160, each a synthetic recipe with its own answer
(analysis or invariants); every other issue in the range is listed with why it was skipped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Cases from the issues filed after #4160, each a synthetic recipe with its own answer
(analysis or invariants); every other issue in the range is listed with why it was skipped.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A tray with seven rounded edges, both rim rounds of a tube, a chamfer on
a joined L-shaped body, and a circular pattern of a chamfered hole, each
with an analytic volume.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Every other fillet, chamfer and blend issue and PR, one line each: auto-filed reports from private designs (picks and error only), sketch fillets and chamfers, UI, previews and navigation, feature and fit-option requests, reference cases that already exist in tests/oracle, surface modelling, and failures that belong to booleans, shell, import, tessellation, sheet-metal or threads.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
The graded volume was right; the derivation text quoted the union as 46476.5 instead of 45571.7.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Copies of filleted and chamfered features (a pasted block, a pattern of pockets with corner rounds, a pattern of chamfered bosses), a grille of rib roots, a join that needs a boolean retry followed by a fillet, and curvature-continuous fillets worked out from the documented quintic section.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Rounds along curved outlines, with the removed volume worked out by Pappus or by integration: merged cylinders, a D prism, a rounded rectangle with 0.02 mm end edges, a long box beside quarter turns, vertical corners after bottom rounds, a bent tube end, a boss's bottom arc, bars running into a boss, an edge ending on a curved wall, and the knife-edge arc corner.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Rounds with their own right answers: a radius larger than the ring it runs along (refused), a pick on a smooth seam (refused), a far edge pick (refused), a round that uses up an end face or a wall, a round over a hole, rounds on both sides of a thin wall and concentric with an inner one, a round on a sphere's flat cut, an edge ending on a tangent seam, and rims on B-spline ramps.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Chamfers on boxes, plates, discs and sectors with closed-form volumes: all twelve edges in the order that was refused, a concave chamfer that adds material, a chamfer next to square openings and one that runs into them, a hole rim tangent to the bottom face, a hex hole's corner bevels, a one-pick chain on a large part, a bottom loop as wide as the corner round, two distances on a circular rim, the end outlines of a rounded prism, a chamfer over a joined pin, and the equal chamfer of a slanted plug. Spline-sided pillar (invariants only) for chamfer and fillet.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>