fillet_the_knife_edge_at_the_tip (features_more_tests.rs) and
blend_a_knife_edge_where_a_curved_wall_runs_out (tests/robustness.rs) build
the same #851 part with the same script, round the same knife edge at
(62 1/6, 0, 5) with R2 and measure the removed volume through the same display
plan. The first integrated the removed area on a grid (5e-4); the second has
it in closed form. Drop the first and keep its tolerance on the second.
The ball 2 from the back face y = 0 and from the r 21 wall about (62 1/6, -21)
is centred at (62 1/6 - sqrt(168), -2). The removed section is the trapezoid
wall centre, tip, (kx, 0), ball centre (sqrt(168) wide, 21 and 2 high) less the
wall's sector theta = acos(19/23) and the ball's sector pi - theta:
10 (11.5 sqrt(168) - 220.5 theta - 2 (pi - theta)) = 119.648812 mm^3
the constant the kept test has; the dropped test's grid gives 119.6487 at a
0.004 x 0.001 step. The kept test's fillet bound goes from 0.5 to 5e-4 of
that (0.0598), the dropped test's. Its chamfer row (159.236451, the chord
triangle less the wall's segment) already says the chamfer takes more.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
cut_whose_end_touches_an_arc_side_leaves_no_sliver compared the touching cut's
face count with a clear cut's, a count of how the kernel splits its faces. It
now compares what the two parts are.
The plate's arc runs from (0, 20) through (-10, 10) to (0, 0): centre (0, 10),
r 10, so it reaches x = -10 only at y = 10. The r 5 cut along x about
(y, z) = (12.5, 12.5) spans x -10..7.5 (touching) or -10.1..7.4 (clear). Both
open the same patch of the arc; the slice x 7.4..7.5 lies wholly inside the
plate (y 7.5..17.5, z 7.5..17.5 in 0..20 x 0..27.5). So
V(clear) - V(touching) = pi 5^2 0.1 = 7.853982 mm^3
A(touching) - A(clear) = 2 pi 5 0.1 = 3.141593 mm^2 (the hole wall; the
floor disc is the same)
both to 1e-4 (the measure integrates the exact faces to 1e-8). A sliver of the
arc left where the end touches adds about a square millimetre of faces.
Seed 14's half (the fuzz generator's seed, then a shell) is pinned as its own
test, shell_after_a_cut_whose_end_touches_an_arc_side, with the commands the
generator gives today: the touching cut, then a 2 mm shell opening the top
face y = 20. It fails at the shell (SMLib status 1001), a kernel gap.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Stale since 84bd2daad, which gave solid.fillet each pick's tangent chain by default. After the
long top front edge is rounded, the front-left upright meets the round's end (the quarter circle
on the left face) along its tangent, and that circle meets the top-left edge along its tangent:
the second fillet rounds the upright and the top-left edge. The "together" fillet picks the
three edges ([20, -21, 10], [0, -21, 5], [0, -10, 10]); one by one and together remove the same
volume within the display meshes' 2e-4 (it read 60.649 vs 43.185 with two picks).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The test offset the sphere's top patch to get a fitted B-spline sheet. That held on truck,
whose sphere came in several patches and whose sphere offset was fitted. On SMLib the
sphere is one face: offsetting it closes up, so it is a solid by design (surface_offset.rs,
"Faces that close up make a solid", and its test a_sphere_is_fitted_and_refused_past_its_centre
asserts exactly that), and SMLib's offset is exact, a sphere of radius 22 with no control
points, which surface.fair refuses. Body::is_surface was right: the record lists the offset's
closed shell as the outer shell of a material region (Parts::canonical), so it is a solid
whether read from edge uses or from regions.
The test now fairs the patch on the non-planar rim of a box cut by a sideways cylinder (the
cover in patch_trim_thicken_and_stitch), a one-face B-spline sheet: energy 0.7185 → 0.6938 in one
step, edges unmoved bit for bit, undo/redo/reopen and the refusals as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
hostile_params_never_panic built a box, a sketch and a rectangle afresh for each of the ~3000
calls it makes per command. SMLib serialises every call behind one process-wide lock, so those
boxes were built one after another whatever the number of threads: 20 threads made 4000 boxes
in 7.8 s, one thread 200 in 0.31 s (1.5 ms each). The fixture was nearly all of the test's time
(8814 of 8823 thread-seconds over the first 72 commands on the aarch64 box; the commands
themselves 9 s, none over 0.5 s), and the test took 2195 s in develop CI.
It now builds that model once per command and gives each call a copy of the session with its
design, model, undo, redo, open sketch and log, sharing the bodies as undo does. Every command
still gets every parameter name with every hostile value, from the same starting state. A new
check runs Cancel Sketch, two undos and a redo on a copy and on a session built afresh and
finds the same designs, with the copied session untouched.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The refusal "capture the source occurrence position before generating a
legacy face profile across components" lost its test when Offset Face got
an exact history name (b6c3bf3c5). A half of a box's top that Split Face
divided still has neither a construction certificate nor an exact history
name, so Extrude from that face, in a component whose occurrence has an
uncaptured move, takes the legacy path and is refused there; the document
and the pending moves stay as they were.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The kernel switch broke these tests only through their counts, which record how a kernel splits
faces rather than whether the result is right. Each now checks its intent:
- a fitted circle is the exact circle (centre, radius, a full turn), not "one segment";
- the tight bend sweeps a valid solid of Pappus' volume, πr²(40 + 5π/2), not a count of faces,
edges and vertices;
- the Pi case keeps each outer side one face, stays valid after every feature and rebuilds the
same topology at 32 whether built there or edited there, without a hard-coded table of totals;
- a certified paint stays on the wall's radius and covers as many faces after an edit, a copy
and reopening as when it was painted;
- the offset sleeve and the extended strip are checked by their exact areas only.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillets_on_tapered_bosses_saved_before_still_find_their_edges compared the part with
69454.885209 mm³, what the truck build that saved it measured. In closed form: the 80 × 40 × 20
block (64000); the 20 × 20 boss 10 high tapered 5° in, a frustum to a 20 − 20 tan 5° square
(3660.251034); the Ø16 boss tapered alike, a cone frustum to radius 8 − 10 tan 5° (1798.751833);
less the R1 round on a sloping corner, the corner's section r²(cot φ/2 − (π − φ)/2) at its
dihedral angle φ = 90.435° times its length between z = 20 and 30 (2.124401), and the R0.5
round all round the cone's top, the section at the rim's 95° turned about the axis by Pappus
(1.928463): 69454.950004. SMLib's part measures 69454.950004.
The test still fails before that check: Fillet2's saved edge `F4:side:c1#1|F4:top#[F4:side:c1]`
names a half of the cone wall truck built, which SMLib builds whole, so it is found with a
"was split" warning (a persistent-name question, see the PR).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since 0a216d692 tangent and curvature extensions are SMLib's G1 and G2 extension of the surface
(smlib_extend_sheet, CreateExtendedSurface), and the face stays one face on it, as
surface_extend's docs say; extend_a_cylinder_strip_every_way still counted truck's separate
run-off face (2). It counts 1.
The test still fails after this, on the curvature run-off's area (see the PR): SMLib's G2
extension of the quarter cylinder by 5 gives 413.882 (a section 4.986 long), where the test
works out the parabola's 418.182.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
cut_keeps_posts_joined_while_apart_in_one_body expected the reply's `bodies` as
["Case", "Case (1)"]. That list is the state's order, which is SMLib's lump order (the -x half
first); the names follow the pieces' faces (lineage::order_lumps, 08cf526fe): the piece whose
least face name sorts first keeps "Case". That is the +x half, whose least is `F1:+x`, before the
-x half's least, its piece of `F1:+y`. The test now checks the names as a set, that the +x half
(from x = 1) is "Case" and the -x half (from x = -30) "Case (1)", and each half's volume as
before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since 09c979a4b a circle is one closed arc, so an extruded circle's wall, a hole's wall and a
cylinder's side are one face each, closed along a seam. Tests that counted truck's two halves:
- certified_annulus_side_rows_follow_radius_edits_and_clone and
certified_side_transfer_preserves_geometry_and_unsupported_taper_refuses_atomically: the
painted outer wall is 1 face (every vertex of it still at the painted radius), not 2;
- offset_surface_of_a_cylinder_and_a_box_top: the offset sleeve is 1 face (its area 2π·12·20
unchanged);
- press_pull_then_curved_face_offsets_it: a click on the hole's wall offsets its 1 face;
- pi_case_faces_per_step_at_both_heights: each standoff (a ring, Ø6 round a Ø2.5 hole) adds 4
faces, not 6: its outer and inner wall, its top, the floor inside its hole. So 23 after the
first and 35 after the pattern of four; the port openings (3 × 4), the end cut-out (4) and the
five vents (5 × 4) are planar and add what they did: 47, 51, 55, 71.
- the_round_sides_of_a_thin_ring_are_named_by_the_circle_they_run_beside: a thin ring 2 thick
about the R10 circle has two walls, `F2:wall:c1:left` (radius 9: the counter-clockwise
circle's left is inside) and `F2:wall:c1:right` (radius 11), with no numbers; each name is
found again by a point on its own wall.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Two expectations encoded truck-era output:
- a_flange_bent_inside_keeps_the_base_sketchs_arcs_in_the_flat_pattern_and_the_dxf: the
DXF has 7 LINEs, 4 ARCs, 11 shapes (was 9, 4, 13). The flat outline is SMLib's exact 2D
union of the plate, the bend zone and the flange panel; a zone's side and its panel's side
meet in line, and a region's boundary has no vertex in the middle of a straight run, so
each flange side is one line: 6 outline lines (plate top, left, right; flange sides and
end) and the bend's centre line. The same reason as 5d25684a1 gave for
a_base_trimmed_for_a_flange_keeps_its_arcs (12 to 10 edges). Areas, the bend length and
the volumes are checked as before and hold.
- hole_beside_two_adjacent_edge_flanges_cuts_and_bends_stay_guarded: the folded volume was
14057.2 +- 0.1, a faceted measure; since 32ae0cd9c the measure is SMLib's exact integral,
14057.3837123. Exactly, a folded sheet holds its flat area A times t, less each bend's flat
strip L·t·(R + K·t)·π/2, plus its sector L·t·(R + t/2)·π/2: t·A + t²·(½ − K)·(π/2)·L. With
t = R = 2.5, K = 0.44, A = 5597.0353454 (the flat pattern) and L = 75 + 35, that is
13992.5883635 + 64.7953485 = 14057.3837120, within 2e-11 relative of the measure. The
test now checks that identity to 1e-9.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fixed_seeds_run_clean expected the join of a box touching the first only along
an edge to be refused with "zero-thickness edge contact". Since 94ee28d5c (doc:
a join keeps solids that only touch as separate bodies) such a join succeeds and
keeps the new box a body of its own with an along_edge notice, which
join_touching_along_an_edge_keeps_a_separate_body asserts in engine tests.rs.
The seed now expects that: the notice, two bodies, each valid, and the volumes
unmoved, 25 x 15 x 10 + 17.5 x 17.5 x 20 = 3750 + 6125 mm^3.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Under the blend-overflow decision (237f0ae74) a convex round running over a face's far
edge (a cliff) is built and cut from the part, so the truck-era fixtures of the reduce
and taper fits (a 2 mm fin, a plate narrowing to 2 mm, a wedge, a 10 mm cube's edge at
R20) no longer refuse their radius and the fits have nothing to react to. Each test now
uses a case SMLib still refuses, and checks the cliff case builds:
- engine fillet_fit_reduce_keeps_the_radius_where_it_fits: a 14 x 6 x 10 post on a
40 x 30 x 20 block, its four verticals at 3.5 (two rounds would cross on its 6 mm ends)
reduced to 3 on 4 of 5 edges, the block's corner kept at 3.5: 24840 - (4 - pi) 90 -
(1 - pi/4) 3.5^2 20. New fillet_fit_reduce_keeps_a_round_over_a_cliff: the fin's R4
builds, nothing reduced, at the kernel's fillet_max_each answer.
- engine fillet_fit_taper_follows_the_room_along_the_edge, spline_fillet_takes_over_a_taper,
kernel taper_follows_the_room_along_the_edge, ui-egui fillet_spline_handle_tests: the
narrowing plate stands against a wall behind its slanted side (z -15 to 30), so its top
and bottom end in concave edges: R3 is refused and tapers 3 -> 1.8 as before. Without
the wall, R3 is cut over the 2 mm top's far edge and kept constant: at x the section
loses (1 - pi/4) 9, or 3 w - (F(3) - F(3 - w)) where the top is w < 3 wide, 6522.7745566.
- The wedge closing to a point: on its own R16 is cut over its cliffs (the section
integral, 4195.578821, SMLib within 4e-8) and kept; its room's taper is checked as a
spline fillet. Against a wall (new fillet_fit_taper_closes_to_a_point) the taper must
close to 0, which SMLib fails today (status 1001).
- kernel taper_mesh_tests: the collapsed taper is built from taper() as a spline fillet.
- ui-egui the_feature_menu_copies_a_warning_message: the 10 mm cube's four verticals at
6 are reduced to 5 (a full round), which the warning says.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The owner's blend-overflow decision (2026-10-25, 237f0ae74): a convex round or chamfer
whose rail runs off its face across a cliff (an opening's rim, a hole, the part's
outline) is built on the faces continued and what it removes is subtracted, so it never
bridges an opening; a round may use up a face; a chamfer of a face's full width stays
refused. These tests still expected truck's refusals. Each now expects the decision's
body, with its answer from the geometry:
- issue_1080 chamfer_into_a_pocket_is_cut_by_it (was ..._is_refused_with_the_size_that_fits):
chamfer 6 into the pocket 4 mm in removes 360 - 20 (its triangle less the part over
the pocket): 14660; 6 along the top and 2 down, 120 - 20/3; 2 and 6, 120.
- issue_1080 fillet_into_a_pocket_is_cut_by_it_and_one_that_fits_builds: R5 removes
(1 - pi/4) 25 along 20 less 10 (5 - (sqrt(24)/2 + 12.5 asin(1/5))): 14893.0344442.
- issue_1080 chamfers_crossing_each_other_are_refused: still refused (they cross);
chamfer_max and fillet_max find 2 mm.
- issue_1080 rounds_on_both_sides_of_a_wall_build_as_one_fillet: R7 alone opens a slit
where its arc passes the inside corner: V0 - (104 (1 - pi/4) 49 - 100 a), a = the square
[25, 30] x [35, 40] outside the circle about (25, 35), 5 (5 - sqrt 24) - (F(5) - F(sqrt 24)):
38458.8958265. Both at R7: the arcs about (25, 35) and (23, 33) cross only outside both
quarter arcs and the inner round's material holds the slit, so V0 - 4 (1 - pi/4) 49 =
39509.9380404 (was expected refused).
- issue_324 a_round_into_a_hole_is_cut_by_it (was the_radius_offered_beside_a_hole_fits):
R4 over the r3 hole: 8000 - 90 pi - (640 (1 - pi/4) - the round's height over the
hole's width, integrated with y = 17.5 - s^2): 7580.2873154.
- issue_851 arc_top_blend_uses_up_the_wall_and_refuses_a_collapsed_one: a round of the
wall's full height uses the wall up (one face for the wall, the removal integrated as for
the other sizes); the full-height chamfer stays refused.
- kernel tests: fillet_max_finds_the_largest_radius_that_works keeps the post (3.5 -> 3)
and the no-edge case; its disc and notch cases move to
rounds_past_the_bottom_of_a_wall_are_cut_from_the_part: the 2 mm disc's R2.5 turned
section, pi (338 - integral of (169 - rho^2) dz), rho = 10.5 + 2.5 cos(theta) (the same
formula gives SMLib's R2 994.15188 exactly), 957.6922389; the notched block's outline
R7, 11925 - (1 - pi/4) r^2 (140 - 8 c), c = r (10 - 3 pi) / (3 (4 - pi)) (SMLib's R7 within
5e-8), and R8 less its part over the notch, integral of 2 (5 g - g^2/2), g = 8 - sqrt(64 - t^2).
- kernel tests: chamfer_wider_than_sloped_basin_rim_is_cut_and_a_full_width_one_refused:
past the 1 mm and 0.5 mm rims the chamfer runs over the slab's front edge and is cut:
the clipped triangle's area (30 + z centroid), its length 60 - h between the sloped end
walls (the same formula gives chamfer_sloped_basin_rim's fitting chamfer to 1e-12);
a chamfer as wide as the rim is refused.
- blend_corner sloped_rim_fillets_stay_inside_the_material, equal_slope_rim_loops_stay_
inside_the_material: R4 and chamfer 2 over the thin rim build, every vertex inside the slab.
- engine blend_fit chamfer_through_the_openings_is_cut_by_them: the report's 9 mm chamfer
is cut by the openings, 3350 (the rig's fillets/1080 case).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
When the kernel's room pre-check went (bcbb99005), a fillet or chamfer refused as
too large stopped saying what would fit: only SMLib's NO_ROOM words were left. The
rig expects the refusal to name it (fillets/4782-fillet-two-end-verticals-past-a-full-round:
"the largest radius that fits is 7.5 mm", fillet_max for the exact fit).
A constant fillet with the exact fit, and an equal-distance chamfer, refused as too
large now add "; the largest radius (distance) that fits is X mm", found by the same
bisection fillet_max runs (up to 16 blends, three significant digits), now shared with
a new kernel::chamfer_max. Where the search itself fails (a candidate failing for
another reason), the refusal is left as it was. The reduce and taper fits and the
kernel's own searches call the kernel blends directly and do not pay for it.
Tests: the 14 x 6 x 10 post's R3.5 names 3 mm; a 4 mm rib's crossing chamfers and
rounds at 3 name 2 mm.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
legacy_internal_capture_refuses_an_uncaptured_source_in_another_component
picked the top Offset Face raised as a face with neither a construction
certificate nor an exact history name (#494), to reach the legacy path
that refuses a profile across components while the source occurrence's
move is uncaptured. Offset Face has SMLib's history since 0f3d6f177 (shell,
offset faces and thicken through SMLib), so that top is now named exactly
(F3:+z#[F3:-x], verified) and capture_face_anchor gives it a lineage
anchor; the legacy path is not taken, and the capture is right to
succeed: an anchored attachment captures its path's pending positions
when it is made (capture_positions).
The test, renamed to what it now checks
(internal_capture_in_another_component_anchors_an_offset_face_by_its_history_name),
asserts the face still has no construction certificate, the capture is a
Lineage anchor on the occurrence's path, and capturing changes neither the
document nor the pending moves.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
explode.show put the view's placements in the uncaptured moves, so occurrence.properties reported
the exploded placement and Capture Position (and reparenting, moving bodies between components,
copying or pasting in place, URDF export) wrote the view's offsets into the design. The session
now records which uncaptured moves are the view's (Session::exploded); what reports the design's
placements or works a new placement out from them uses the design's own moves
(uncaptured_moves, design_document), while the viewport and picks still show the view.
New case cov-explode-show-keeps-the-placements: the arm's properties are the same before, while
and after the view is shown, and Capture Position keeps nothing. The two explode cases that read
occurrence.properties while exploded now expect the design's placement, centre (20, 0, 5), as the
command says ("shown only; the design keeps its placements").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Both walked the picked curve's display polyline: a point a third along an R10 sketch arc was
0.87 µm off (8.6603, 5). They now evaluate the path's exact curves by arc length: lines and arcs
in closed form, a free-form span at the parameter its arc-length integral reaches (body edges by
their record curves, 3D sketch curves by their arc, spline, line or linked exact curves; only a
curve that exists as points alone, an intersection edge or a projected curve, runs along them).
The arc's point is now within 1e-12 mm of (10 cos 30°, 5, 0).
A t outside 0…1 was clamped silently, which the contract (`t: expr, 0…1 along it`) does not
say: it is refused ("t is 1.5: a point along a path is 0 (its start) to 1 (its end) of the way
along it"). The construction cases grade the arc and line to 1e-9 mm, past-the-end is refused,
and a new case takes the middle of a symmetric cubic spline, (20, 7.5).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
When a − b or b − a cannot be made (a kernel error, or a body that encloses no volume), the
region's volume and centre are null, measured_by is "not measured" and not_measured gives the
cut's error; its deviation, area, faces and box are still given, the side's total is null and
the verdict says the volume is not measured. The integrated-along-lines estimate is no longer
reported as a volume.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
inspect.compare integrated a region's volume along sampling lines: the
40 x 30 x 5 slab between a box and one 5 mm taller came out at 5976.49 mm3
against 6000. The regions are still found from the two surfaces; each one's
volume, centre and box now come from the pieces of the exact cut a - b (or
b - a) that lie there, measured as inspect.measure measures a body
(measured_by: boolean). Where a cut cannot be made the region keeps the line
integral, marked measured_by: lines, with a warning. The rig case
cov-compare-taller-box passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
inspect.center_of_mass measured each body's display mesh, so a cylinder r 5,
h 10 came out at 784.13 mm3 against 250 pi = 785.40, and the answer moved with
display quality. It now takes the exact mass properties inspect.measure uses
(ModelBody::measure), skips bodies that enclose no volume as Measure does, and
lists what it skipped. The rig case cov-center-of-mass-box-and-cylinder passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's parallel projection (CreateParallelProjectionCurves) gives every curve where the
projecting lines cross the face: a line projected down onto a ball came back as its top and its
bottom, each split at the pole, and the link's first wire was half the bottom. A projection onto
a surface is where those lines first hit it (owner's decision, as mainstream CAD does): a curve
is now kept only when the first hit on the body's mesh along the line through its middle is the
curve itself (within 4 chord tolerances), and the pieces that meet end to end are joined in
whatever order and direction they come, a piece run the other way exactly (its knots and
control points reversed; a line's, circle's or ellipse's parameter mirrored). The ball's top
is then one wire from x = -10 to 10.
three_d_sketch_curves now expects that exact curve: one wire, its ends at (±10, 0, √300), every
point of its exact curves on the sphere of radius 20 in y = 0 over the top, to the projection's
own tolerance (a millionth of the body's size), and sweeps_and_pipes_follow_3d_sketch_curves
pipes along the whole joined top. Both pass on the pinned SMLib (90aabff): the pieces lie 9.1e-6
off the sphere against a 4e-5 tolerance and meet at the pole within 4.7e-8 rad, since the fork's
8d95600 keeps the pole's exact tangent in StepBackFromSingularity.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A symmetric surface.extrude given no convention now splits its distance
evenly around the start plane (10 mm: 5 mm each side), the way
solid.extrude reads it, instead of going the distance each way. Both
commands take their default from one function, which a session setting
(surface_extrude_symmetric_per_side) can turn back to the per-side
reading for surface extrudes. timeline.edit and timeline.redefine give a
one-sided surface extrude made symmetric the same default.
Saved designs are unchanged: every surface extrude saved its convention
(legacy_per_side), and one saved before the marker existed reads per side
as it always did. The help of both commands says how the distance is
read. The 3830 kernel case, recorded with the per-side reading, now says
so explicitly.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
notch_into_a_ring_chamfer_is_cut_exactly measured the notch as the ring's mesh volume before less
after (0.2906 against the integral's 0.28665) and oblique_cuts_through_a_chamfered_ring_are_exact
compared the two mirrored cuts the same way (3.3e-4 apart). The cut is right: the ring less the
cut ring is a piece of 0.2866521 mm³, the integral to 2e-6. A difference of two 1149 mm³ volumes
is not: the re-tessellated ring's mesh volume moves by 4e-3, and SMLib's mass properties (at
their finest, 1e-4 asked) by 1.5e-6 of the ring, 1.7e-3. Each cut is now measured as the piece it
took away (the ring before less the ring after, an SMLib boolean), to 1e-5 of the integral and
1e-6 between the two mirrored cuts.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib keeps a whole cylinder one face and the arm's round end and the boss over it (one
cylinder) one face, named for the arm's end. Three naming tests relied on truck's pieces:
- a_cut_through_one_of_two_bosses_names_only_its_own_walls finds the boss's wall by a point
on it (the centroid of truck's half cylinder lies on nothing now) and checks it keeps its
name through the cut and the fillets;
- split_pieces_keep_their_numbers_across_evaluations keeps the torus (its sweep's walls are
whole now, their names stable) and adds a disc whose top a round groove splits into
F1:top#1 and #2;
- a_design_saved_before_pieces_were_numbered_by_place_keeps_their_numbers uses that disc,
whose kernel order numbers the pieces the other way round from their place (the post's
side of multi-body-join-cut is one face now).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- shell_tangent_chain_that_opens_every_face_explains_how_to_keep_walls: the shell is the
rounded box (its 37 x 27 x 57 core grown by the 1.5 ball: 71753.436) less the sharp 36 x 56
x 28 cavity, 15305.436, to the measure's 2e-7 (SMLib: 15305.445); truck's was 15305.28.
- press_pull_on_curved_faces: the shell's inner wall behind a fillet is offset as a face
(SMLib builds it, truck refused it as tangent to its neighbours): pulled 0.5 into the
cavity it adds exactly the quarter ring π/4 (3² - 2.5²) 18 = 38.877.
- revolve_cut_round_a_box_corner_does_not_panic: the side face is picked by its point; the
report's face index was truck's face order (SMLib's face 1 is the opposite side).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib keeps a whole cylinder (and an arc of one past half a turn) as one face closed on its
seam, where truck split it in two; its holes are exact circles; its mass properties come
within 2e-7 of a closed form. The tests that counted truck's pieces or its polygon hole now
check the exact geometry:
- extrude_of_adjacent_profiles_has_whole_edges: the cut-off cylinder is 4 faces (arc side
4674 = 40·(2π − 1.2019)·23, chord side 1039.8, two ends);
- step_export_of_an_enclosure_with_a_screw_hole: 27 faces, as the file holds them;
- model_faces_gives_a_point...: the hole's wall is one cylinder, its centroid on the axis;
- draft_takes_a_cylinders_side_by_name: one side face (the draft itself waits for SMLib's
draft of a cylinder);
- convert_to_sheet_metal_takes_the_plates_face_by_name: 15000 − 62.5π to the measure's 2e-7;
- a_checkpoint_survives_file_new: a unit box measures 1 + 2e-16;
- creating_a_component_recomputes_nothing: SMLib's boolean keeps the face certificate the old
setup relied on losing, so the legacy face plane is made as a design saved before face
attachments were certified (its anchor removed) and reopened.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Since the section hatch per part (#8529), a cut is tinted toward the hatch colour its body's
name picks; Body1 picks the steel one, so the cap test's warm pixels were none
(cpu_picture_section_caps_hide_the_inside). The test turns the part hatch off: it checks that
the cap hides the inside and shows its colour, which the hatch tests cover per part.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
solid.shell takes faces: [] since 1df330c79 (a closed hollow body), so its row in
shared_types_keep_the_handlers_messages no longer matched the shared FaceRefs message. The row
uses solid.draft, which still refuses it; FaceRefs says shell's exception.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
picked_edges_give_the_sketch_s_table picked [E + R, 0, 5]: on SMLib's extruded circle that is the
vertex where the side's seam meets the top rim, a pick either edge answers, and it took the
seam. The pick is now a quarter turn round the rim, [E, R, 5]; the product's pick rule is
unchanged (owner's call).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
a_face_picked_by_point_on_a_block_with_a_modelled_thread_is_found guarded #6720 (the face search
charged the whole mesh once per face) with a modelled thread's 5 000 facets. On SMLib a modelled
thread is a few exact helical faces, so the block had nowhere near the 1000 faces the test
asserts, and the case no longer reached the old charge. A block drilled with 16 x 16 holes does:
the test now asserts its faces times its mesh's triangles is past the search's 2 000 000 budget
(the old charge) while their sum is well inside it (the new), then picks its top by point.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
intersect_keeps_its_exact_cuts pinned the tilted cylinder's section to 21 segments and one
segment's ends to 1e-4: the crossings of truck's mesh. The cut is the mesh's segments, as many
as the tessellation crosses (20 on SMLib's), each end within the section's reach of the surface,
the display tolerance (a thousandth of the mesh's size, doc::project::fit_segments; SMLib's ends
lie 6e-4 off at most, the test's limit is 0.051). The test now checks that every curve is a
line, at least 16 of them, and every end lies that close to the cylinder of radius 5.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ids_names_suppression_marker_and_failures_survive needs a feature that a parameter change makes
fail, to see the failure survive the script's replay. It made a 1 mm round 50 mm, which truck
refused as too big; SMLib builds a convex round wider than its faces by subtraction (the owner's
overflow decision), so that round now succeeds. A radius of -1 mm fails on any kernel, and the
replay still has to keep the failing feature, its id and its marker.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
a_face_engraved_with_text_projects_its_letters_exactly_and_extrudes counted the letters' pieces
as control-point splines. A TrueType outline's curves are quadratic Béziers, which are parabolic
arcs, and the cut made on SMLib keeps them exact: the projection gives 222 conics and 154 lines,
no splines. The count now takes conics with the splines. (The cut itself needs SMLib 1a1bebc;
with it the test passes.)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
loft_cut_through_a_shelled_basin_in_either_order asserted one body. The loft's top section is
the basin's full 100 x 60 outline at z = 10, so the cut takes the walls' whole cross-section
there and leaves the walls above (z 10 to 30) touching the rest only along their outer rim, an
edge: two pieces, which a cut makes two bodies (eval's lumps rule). SMLib gives exactly that;
truck kept them as one. The test now expects two bodies, the upper one the walls' exact
924 mm² ring times 20 = 18480 mm³, and the total as before (41582.028).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
a_face_sketch_saved_with_fitted_letters_reopens_and_builds_the_same compared the part with the
5916.018831 mm³ its saving build measured, to 1e-3. The part is the 30 x 20 x 10 block less the
"S" 1 deep and an r 2 circle 3 deep clear of it: 6000 - 46.290121 (the letter's exact profile
area, Sketch2's smaller region) - 12 pi = 5916.010767. SMLib measures 5916.010768 (1.2e-6 off);
the saved figure was 8e-3 off. The test now checks that closed form to SMLib's 1e-8, and counts
the letter's exact pieces as conics or splines (its quadratic Béziers come in as conics).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
unsupported_face_has_explicit_fixed_alternative_and_no_live_projection needs a planar face with
neither a construction certificate nor an exact history name, so a sketch on it must be fixed.
Its face, a split top face offset up, now keeps its history through SMLib's offset and gets a
name. A rib reports no roles for the faces it builds (Traced::unnamed, eval_more), so a rib's
wall has neither: the test now picks the wall at y = 12 of a rib in a bracket's corner.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
interference_lists_a_pair_it_could_not_check needed a pair interference cannot check. Its
pair, an arc revolved up to a post's wall, was one truck could not intersect ("not verified");
SMLib intersects it exactly, and that reason is gone from the code. The pairs left unchecked
are a kernel failure, the time budget, and a mesh body: an imported mesh has no exact surfaces
to intersect (owner's call). The ring is now brought in as an STL beside the post, and the pair
is listed with "mesh body: not checked" instead of passing as clear.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
freezing_rebuilt_arc_borders_keeps_authored_dimension_entity_indices needs the projected
border of the sketch's face to come back with a different number of curves. Truck split the
sector's arc into pieces that changed with its sweep (270 to 300 degrees); SMLib keeps one arc
whatever the sweep, so the count stayed 3. A notch, clear of the sector until a parameter moves
it across the arc at 90 degrees, now splits the arc border into two arcs and the notch's sides.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- A section's chains are walked from either end, whichever segment the mesh's triangle order
puts first at a node (doc::project::fit_segments), so a line's direction says nothing about
the cut. SMLib's box tessellates in another order and the outline came out clockwise: the
same four lines. The two box-outline tests now compare each line with its lower end first.
- The base rim of SMLib's cylinder is one closed circle edge (truck's was two seam halves), so
projecting it gives one exact ellipse. Checked against the closed form: a radius-5 circle in
a plane tilted 45° projects to semi-axes 5 and 5·cos 45° = 3.5355339 (the reported minor
radius), and every sampled point lies on x²/(5/√2)² + y²/5² = 1 within 1e-9, as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Linking a reference (sketch.include_3d, project, intersect) stored the link's wires as points
only: add_link_unless_present called add_link_with_wires and dropped the resolution's exact
curves, which only the next refresh of the sketch filled in (doc::project, since 7952516eb).
So an included box edge had no exact line until any edit refreshed it, and the wire changed
under an unrelated sketch edit. The exact curves are now set with the wires when the link is
made, as a refresh sets them.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The thread forms (b4549d270) parse designations in thread_forms, whose refusal for a plain
M28 said "give it: M28x1" and, for M0 or M1e9, still offered a pitch. The hint the hole
command gave (the two coarsest ISO fine pitches that suit the diameter: M28x2 or M28x1.5) is
now thread_forms::no_coarse_pitch, used by both; a diameter no metric thread has is an
unknown metric thread. The test's "unknown thread" follows the forms' wording ("unknown
metric thread").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
#5191 read the header's preprocessor version and FILE_DESCRIPTION, so a SolidWorks file named
only there was stood up. The reader had moved to crates/step (p21.rs) before #5191 merged,
and the merge kept only the originating system: a file naming SolidWorks in its description
got no exporter_up (step_replies_name_a_y_up_exporter). The parser reads both fields again,
StepImport carries them, and exporter_up looks at all three.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The patch fill meets its neighbours to G4, so Construction::Patch now offers g0 to g4: the
surface.patch command takes g3 and g4 and the Patch dialog's continuity row offers
"Curvature change" and "Smooth curvature change" by itself, from the one table.
The three-round corner test patches G2, G3 and G4 and reads the seams with the Continuity
Analysis too: the middle of each seam (30-70 %) at the order asked; the whole seam G1, since at
the corners the rounds' curvatures differ and no patch can meet both.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5Lzv2n8fyKqD61NCHSF
The command worked the repair out itself for its reply and the feature worked it out again
when it evaluated. The evaluation now keeps the kernel's report on the feature's result (as
an import keeps its import report, cached with it), and the command's reply is built from
that: one repair per call, and a part with nothing to repair fails the evaluation, which
leaves the design unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A new undoable feature (`repair`, one pending format file) and command with input and
output schemas. In order:
- A cylinder, cone, sphere or torus face SMLib refuses on its own is rebuilt on a NURBS
form of its surface laid on arcs from where the face starts
(`form::surface_on_own_arcs`), with SMLib's own trims: the import's quarter-grid form of
a face round most of a turn closes on itself, which SmTorus::IsNurbSurfaceTorus does not
recognise. Geometry unchanged.
- Free edges that pair up within `gap` are sewn by SMLib's stitch; GlueEdgesGeneral gives
each glued edge its own tolerance (at least twice its gap), the body's and the other
edges' stay. The result is checked against the input's own SMLib check, the
tolerance-bound tests (#5, #6, #59, #82) exempt.
- Loops of free edges left are holes: offered as surface.patch, and with patch_holes made
(flat only when the loop is planar and every face around it is a plane, else G1) and
sewn in.
The reply reports what changed face by face; nothing to do is refused with why.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
a_combine_tool_stays_where_it_is_placed makes a part and then moves its occurrence
to check that a combine tool stays where it is placed. Since #2804 the design's first
part is grounded when it is made, so the occurrence.move refused and the test never
reached its question. The part is now made with grounded: false, as a part that is
meant to be moved is; the checks are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
fillet_into_an_earlier_round picked the box's upright after rounding its top edge
and expected only that edge rounded. Since solid.fillet rounds each picked edge's
tangent chain by default (84bd2daad), the upright runs on through the first round's
end arc into the top right edge, and that is rounded too. The two-radius checks now
ask for exactly the picked edges (tangent_chain: false), and a new check rounds the
chain and expects what a round of the 38 mm top right edge takes off as well.
ribs_flush_with_a_window_change_nothing_away_from_them compared the lid with
6703.5222 mm³, the old kernel's chorded volume. The lid's closed form (the plate
with its rounded corners, the skirt, less the window, the slot and the notch) is
6703.5344 mm³, which SMLib gives; the test computes it, and the script's
description says it. Each rib's volume and area are checked to SMLib's mass
property accuracy (2e-7 relative) instead of 1e-6 absolute.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The seeded robustness goldens (tests/robustness/goldens.json, tests::robustness_goldens) recorded
what truck built for seeds 0-95, so they now fail on every seed SMLib builds differently. The
kernel-cases ladder (tests/kernel-cases/ladder, cargo xtask kernel-cases --ladder), whose cases
each carry their own right answer, supersedes them.
Gone with them: fuzz::golden, the CI goldens lane (the goldens output, SLOW_SEEDS, the re-record
hint), their nextest filter and priority entries, the mutants sample and the tests/robustness/
test-data mapping in affected.py. The robustness seeds and tests::robustness stay. The docs point
at the ladder.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>