Each seam now also reports the jump of the curvature's arc-length derivative across it (G3)
and of its second derivative (G4), both from the faces' exact partials, and its order: the
highest one every station meets within the tolerances (two new tolerances, defaults in the
kernel). The verdict keeps its meaning (smooth is G2 or better). inspect.continuity replies
with the new metrics, each seam's order and a count per order; the viewport widens G3 and G4
seams, the legend and the marker labels name every order in words. The Patch, Blend and
Boundary rows offer the orders the kernel's Construction table says they build. G4's words
in en, ar, de, he, ja, ko and zh.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Every tapped hole now drills the tap maker's tabulated drill. ISO metric takes Yamawa YEU23's
drill size column for cutting taps (printed p.704, M coarse; pp.704 to 706, MF fine): M8 drills
6.8 mm and M12 10.3 mm, where the major less the pitch gave 6.75 and 10.25. A custom metric size
the table lacks keeps the major less the pitch. UNC/UNF (Guhring), G, Rp, Rc and NPT (Yamawa)
were tabulated already. The Thread command's suggested hole for a metric size follows.
The Hole dialog's Tap drill diameter is now a field, the tap maker's drill by default, and the
command's `diameter` with a thread is checked the same way: a drill is accepted from the
internal thread's standard minor diameter (or the tap maker's drill where that lies below it:
Rp, Rc, NPT) to 5% over the tap maker's drill. Outside that the command names the range and
why. The field's tooltip gives the drill, the minor diameter and the range. Presets keep a
chosen drill.
A saved design keeps the diameter it stored, so it builds as before, and editing such a hole
keeps its drill: no preference and no format change. Scripts that give a thread without a
diameter drill the new default; ladder 05/007, 11/003 and rig case threads/2115 follow
analytically, and their golden entries are re-measured from runs (tier 05 re-sorted by time).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
The Rc and NPT drills were rounded to a drill series from a third-party reproduction of DIN 345
and a fractional/letter inch series cited from memory. They now come from the same tap maker's
catalogue the G and Rp drills do: Yamawa YEU23, printed p.709 (Rc, the maximum straight bored
hole with non-full threads, Rc 1/16 to 4) and p.710 (NPT, the maximum straight bored hole, 1/16
to 3). A size its tables lack (Rc 5 and 6, NPT 3 1/2 to 12) is refused as a tapped hole, naming
the range. The dialog's tooltip keeps the standard's minor diameter where the thread ends.
Rc 1/2 drills 17.6 mm (minor 17.807), 1/2 NPT 17.60 mm (minor 17.473).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
An Rc or NPT hole was drilled to the exact minor diameter where the thread ends, a size no shop
stocks. It now takes the largest stocked drill not larger than that: metric drills of the DIN 345
series for Rc (to 100 mm), letter and fractional inch drills by 64ths (to 1 1/2 in, ASME B94.11M)
for NPT; past the series it is bored to the exact value. The Hole dialog's drill shows the inch
size for NPT, and its tooltip the exact standard value. Rc 1/2: 17.807 mm, drilled 17.75 mm;
1/2 NPT: 17.473 mm, drilled 11/16 in (17.4625 mm).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01LUXeKMoxpM7Vuv8Rb6E3K2
The tapped-hole catalogue takes ISO 7-1's Rc and ASME B1.20.1's NPT internal taper threads,
every size of the tables a modelled thread cuts. Their drill is the internal minor diameter where
the thread ends (the reference plane's minor at the face less the 1 in 16 taper over the useful
or effective thread length), derived from the standards rather than a tap maker's table. An
external R is still no hole's.
A tapped hole's options mirror the thread's: `modeled` cuts its thread into the wall, from the
entry, by the same cut as `solid.thread` (now one function both call), and `ease_out` fades its
inner end out before the bottom (ISO 3508); without it the groove stops square at the thread
depth, clear of a blind hole's bottom. The Hole dialog's Tapped rows add Rc and NPT, Modeled
and the End choice (Square, Fade, Fade Length). The format notes in pending/thread-ends.rs and
pending/pipe-threads.rs record the new keys and sizes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The thread dialog offers the pipe threads: G (ISO 228-1), Rp (ISO 7-1), R and Rc (ISO 7-1) and
NPT (ASME B1.20.1). Their sizes are listed by designation without a pitch, one start and a hand
of right or left; a size picked for a hole the dialog sized Rc stays Rc.
Rp, ISO 7-1's parallel internal thread an R screws into, is a form of its own (`rp`): the
parallel profile (H = 0.960491 P) at ISO 7-1's gauge diameters, refused on a shaft. Its cut
meets the analytic material of its profile within 1e-5, as G does.
A taper thread takes a chamfered tip: each end's cone is measured from the major diameter the
taper has at that end. Pipe threads are not ISO metric, so they give chamfer_depth.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A thread's start runs off its free end, plain or chamfered; only its inner end fades out
(ease_out) or stops square. The `ease_in` field, the command parameter (refused now, naming
ease_out), the dialog's Ease In row and their docs are removed; `pending/thread-ends.rs`
drops a saved `ease_in` as the design opens. The runout test covers the short, standard and a
sub-turn fade at the inner end.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The free-end test looked for material 1 to 1.5 pitches past the face's end, beyond the first
pitch so that a chamfer the groove runs out through counts as free. A plate thinner than that
(a boss on a 1 mm plate under M10) had none there, so its top was taken for a free end and
the groove's one-pitch overrun cut into the plate (15 mm³ of a 1 mm plate).
An end is now closed when, over the overrun's whole reach, material lies outside the face's
cylinder (inside it, for a hole) at the radii the groove cuts beyond the face: a shoulder,
plate, head or blind bottom, however thin, steps out past the face, while a chamfer, neck,
countersink or counterbore steps the other way. The band test beyond the first pitch stays
for a cylinder that goes on past a split.
The regression test builds the boss as the app does (a rounded plate, a circle sketched on its
top face, extruded with Join) on 6 and 1 mm plates.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Three forms: `bspp` (G, ISO 228-1, 55° parallel), `bspt` (R external, Rc internal, ISO 7-1,
55° taper 1 in 16) and `npt` (ASME B1.20.1, 60° taper 1 in 16). Their sizes are tabulated
from the public sources: ISO 7-1:1978 Table 1 (its gauge-plane diameters are the G sizes)
and NBS Handbook H28 (1957) Table VII.2; tests check every row against the standards' own
relations.
A taper thread starts at its free end with its standard diameter there (external: the gauge
diameter its gauge length in, internal: at the face). Its groove is the screw sweep with the
section moved 1/32 of the axial travel off the axis (the radial law the runouts use, added to
it), its section reaching just past the crest, and the material beyond the major cone (or
inside the minor cone) is cut with it, as a die or tap cuts the crests. An external one runs
its standard length by default.
The volumes are checked against the profile's material fraction integrated over the tapered
radii: G 1/2 to 2e-6, R 1/2, Rc 1/2 and 1/2-14 NPT within 0.2 % of the cut.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
`tip` was none|chamfer, chamfer cutting every free end. It is now none|start|both: `start`
chamfers the end the thread starts from, refused when that end is not free (a shoulder, or a
stop inside the face), and `both` every free end as `chamfer` did. The dialog's Tip pick offers
None, Start and Both; `tip: chamfer` in a command names its replacements.
The thread's end options (runouts, tip, chamfer angle and depth) came without a format
change file; `pending/thread-ends.rs` records them and rewrites a saved `tip: chamfer` to
`both`.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
ISO 4753's chamfered end bounds the end's diameter by the minor diameter. The default took the
modelled root (the basic d1) for it, so the cone's small circle lay on the root cylinder and
the chamfer ring pinched to nothing wherever the groove reached the end. The default is now
the external minor diameter d3 = d - 1.226869 P of ISO 724, below d1: the cone crosses the
root, each end is a whole disk of d3 inside a whole conical ring. ISO 4753 is for ISO metric
threads; the other forms, whose root is already their design minor, give chamfer_depth.
Ladder 06/017's analytic volume follows (1945.354522563); its golden entry re-measured.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A regression test for the groove stopping at the plate's top: the boss loses the
closed-form volume and the plate keeps all of its 9600 mm³, with and without a runout
and a chamfered tip.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
An edge is left out of the shaded view only where its two faces meet
with one tangent plane (normals within 0.5 degrees) and one curvature
across the edge: at each station the faces' normal curvatures square to
the edge agree within 0.5 degrees' worth, |k1 - k2| <= 0.0087 x
max(|k|, 1/L), L the edge's length, so the continued faces turn apart
by no more than that over a radius of curvature or the edge's length.
Fillet boundaries (0 to 1/r), corner-patch joins and a plane tangent to
a cylinder are drawn again, straight ones included. A modelled thread's
flank pieces (one sweep) differ by at most 0.0046 and stay hidden.
Second derivatives of a spline surface now exist at a boundary point a
pcurve carries a rounding step past the knot range, as its point and
first derivatives already did.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Smoothness (normals within 0.5 degrees) and a crease are separate
verdicts. A crease is certified where the normals differ by more than
the evaluation can account for: each pcurve point's measured distance
off the edge's own curve times the faces' larger principal curvatures.
So a real crease too small to see is not drawn in the shading but stays
a pickable edge in the wireframe, overriding a coarse same-surface seam
fit, as before; exact tangent joins (fillets, seams, a thread's flank
pieces) are no crease.
The viewport's smooth-wall test expects the wireframe to draw
`edge_visible` edges: the offset ellipse's pieces meet at real creases
of 1e-4 rad that the old checker could not certify.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The M10 thread's 32 flank-piece joins meet with normals about 1.5e-6
degrees apart (measured independently with seam_diagnostics); each is
left out of the shaded view, stays pickable and stays in the wireframe.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
v0.24.0 (format 39) saved a left-hand Thread or tapped Hole as `handedness: "left"`; this
branch replaced main's handedness (#4414) with the thread's `hand`, and features don't refuse
unknown fields, so such a design opened right-handed without a word. The pending format change
thread-hand.rs renames `handedness` to `hand` on Hole and Thread features (a `right` is
dropped, anything else refused).
Tapped holes take `hand` again, right or left (never both, and only with `thread`): the Hole
feature saves it, its thread is cut and annotated that way, solid.hole takes `hand?`, the hole
dialog's tapped rows have the thread dialog's Hand choice (without Both), editing a hole keeps
it, and hole presets save it under v0.24.0's `thread_options.handedness` key, so presets saved
by v0.24.0 recall it.
Test: a format-39 design with a left-hand thread and tapped hole opens left-handed; a hole's
`hand` refuses both and needs a thread.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The reworked thread has its own direction, `hand: right|left|both`, on SMLib's
exact screw sweep. Main's #4414 added a second one, `handedness: right|left`, on
Hole and Thread, for the faceted groove this branch replaces. It is taken out: the
field, its pending format change (never released), the hole dialog's direction row,
its hole-preset option, its strings and its tests, which measured the faceted
groove. A tapped hole is right-handed, as before #4414.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HoZgkCdAVrscuw2kjQTWDs
A modelled thread never changes the size of the shaft it is on (#1018, #2853): a
shaft thicker than the thread is refused with the size to make it, as
tests/kernel-cases/threads/2705 expects ("this 14.6 mm shaft is too thick for a
modelled M14 thread; make the shaft 14 mm for M14"). This takes out the turn-down
of #4256: `thread_turn`, the fit that let a thicker shaft through, and its tests;
the 9 mm shaft refusing an M8 and the preview's M6 refusal on an 8 mm shaft are
back as they were before it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01HoZgkCdAVrscuw2kjQTWDs
Ladder 06/009 had no way to ask for one: "solid.thread has no runout (vanishing thread)
length". With SMLib's smlib_screw_sweep_radial (replay e7acea1):
- smlib: the FFI binding and Brep::screw_sweep_radial, the profile moved off the axis by a
piecewise linear law of the turn; crate test: a tooth moved out 1 mm over three turns has
A 2π (c turns + ∫ offset dt).
- kernel: sweep_helix_radial, sharing sweep_helix's checks (helix_profile).
- doc: `ease_in`, `ease_out` (a length, or ISO 3508's standard 2.5 P or short 1.25 P) fade the
groove over that length, its section moving out of the material as it turns (outward for a
shaft, inward for a nut). ease_in is at the end the thread starts from. The runout lies past
the full-form length: beyond a square stop, before a shoulder up to its clearance; at a free
end inside the face. Runouts longer than the thread are refused. No end gets one by default,
so saved threads keep their geometry.
The cut is the integral over the turn of the clipped section's 2π∫ r dA: engine test (2.5 P
and 1.25 P between two collars) within the sweep's wall tolerance times the runouts' wall area
(0.029 against a 0.036 mm³ bound), ladder 06/009 (004's shaft, a 2 P runout before the
shoulder) graded in closed form (measured 1.7e-6 off).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
`tip: chamfer` cuts ISO 4753's chamfered end at each free end a modelled external thread
reaches, after the groove, so the last teeth taper into the cone instead of ending in a
ragged first turn: the material outside a cone `chamfer_angle` to the axis (default 45°)
reaching d_f = d - 2 `chamfer_depth` at the face's end (default the external minor diameter,
the largest the standard allows), a revolved ring cut by one boolean per end. Past the end the
ring keeps to the radii the groove's overrun already cuts. An internal thread is refused (its
entry takes the hole's countersink), as is a tip with no free end or on a cosmetic thread.
The cone is axisymmetric and cut after the screw-symmetric groove, so the volume is the stock's
chamfered section with the thread's material fraction: engine test (both ends 45°, and 30°
x 0.5 mm at a shaft's one free end above a collar) within 1e-4, ladder 06/017 (measured
2.4e-7 off).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Ladder 06/008 had no way to ask for one: "solid.thread has no start count". `starts: n` (1 to
8) cuts n grooves of lead n x P, the j-th a j/n turn round from the first (the same helix j
pitches along), in one boolean with their union. A designation that gives the lead
(M16xPh3P1.5, Tr40x14(P7)) gives the starts, and a `starts` that disagrees is refused. The
helix's self-clearance check and the turn limit use the lead.
Over the same length n grooves of lead nP take the volume of one start of pitch P: engine test
(2 and 3 starts, M10xPh3P1.5) within 1e-4 of the closed form, ladder 06/008 graded as 001
(measured 3.5e-7 off).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Only the ISO metric 60° thread existed. Forms now (crates/doc/src/thread_forms.rs, values and
sources in docs/threads.md): ISO metric (ISO 68-1), trapezoidal (ISO 2904 design profile, ISO
2902 sizes), general purpose Acme (ASME B1.5), metric buttress 3°/30° (DIN 513), buttress inch
7°/45° (ASME B1.9 basic profile). Each has its groove as a straight-flanked polygon, its standard
sizes (none for ASME buttress), its designations (M10, M16xPh3P1.5, Tr40x14(P7), S20x4,
1/2-10 ACME, 2.5-8 BUTT) and the size that fits a face. The square thread is refused: no current
standard defines it.
`hand: right | left | both`: a left-handed groove is the screw motion about the reversed axis
rising along it; both cuts the two grooves, crossing, in one boolean. `steep_flank` turns a
buttress. The design diameters are checked against the published tables (ISO 2904/DIN 103,
DIN 513 via IS 4696-3); every form's cut against 2π∫ r w(r) dr per turn to 1e-4 in engine tests
and to 1e-4 in ladder 06/011 to 016 (they measure within 5e-7).
FeatureKind::Thread holds every option the command has (form, hand, starts, ease_in, ease_out,
tip, chamfer_angle, chamfer_depth, steep_flank, all defaulted so saved threads load unchanged);
starts, runouts and the chamfered tip are refused as not built yet. suggested_thread_in takes the
form.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A thread of some length ran from "the end of the face nearest the pick", a coin toss for a
pick in the middle (rig 602's 4 mm thread meant for the free bottom end ran at the head end,
cutting 1.17 mm into the hex), and every thread end at a face end got a one-pitch overrun,
which at a shoulder gouged the material past it (ladder 06/004 cut 0.9% of its volume out of
the collar).
- kernel: material_in_ring, the exact intersection of a body with a ring about a cylinder
face's axis, by an SMLib boolean.
- doc: a face end is free when no material lies past it, over the span the groove's one-pitch
overrun reaches beyond its first pitch, within the radii the groove cuts (a cap, a chamfer
the groove runs out through, a counterbore). At a free end the groove runs out as before; at
a closed one (a shoulder, a head, a blind hole's bottom) it stops with its widest part clear
of it; inside the face it stops square.
- doc: a thread of some length starts at the end nearest `from`, else at the face's only free
end, else at the end the pick lies within a third of the face of; a pick in the middle of a
face whose ends are alike is refused, naming `from`. A length as long as the face runs the
whole face. `up_to` a plane or a point's place along the axis. New fields `from`, `up_to`
default to none, so saved threads keep their meaning where it was not a coin toss.
- engine: solid.thread takes extent (full|length|up_to), from and up_to.
- ladder 06/003 (now with `from`), 004 and 007 are graded by volume and centre of mass in
closed form (a square stop inside material removes exactly length/P turns, the section being
symmetric); rig 602's method says why the thread is at the bottom, tolerance 0.02%.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A face's boundary nodes are its edges', shared with the neighbouring face.
On a nearly straight stretch (the base of a thread flank's corner, clipped by
a hex head's flats, on an iso-line of the helix) refinement met slivers
between consecutive boundary nodes: their centroid, or the middle of their
inner edge, lies on the boundary chord to rounding. Inserting it split the
boundary constraint, and the face was refused ("boundary crosses itself";
rig threads/602, refused while the body was meshed to pick the fillet's
edges). A sliver whose centroid lies on the boundary is now split at its
inner edges' middles, and a refinement point that lands on the boundary is
not inserted.
The 602 engine test assumed the old kernel's faceted thread (over 1000
faces); with SMLib the thread is exact, and the test now checks that the
fillet finishes and removes a little material.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Body::mesh / mesh_plan / mesh_of and MeshTolerance (chord, display, display_of, export_of)
replace tessellate, tessellate_with, display_mesh*, display_plan*, reference_display_mesh_angular;
every caller in kernel, doc, engine, io, ui-egui, gpu and the CLI renamed mechanically; the
truck-mesher fallback, mesh_shells*, refined* removed; Body::new orients from the planner;
truck-meshalgo dropped from Cargo.toml with the tests of its hooks. Still to fix: trait imports
in tess/*, splitface/lumps/preview/step_in/boolean_record meshalgo uses, measure.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
* claim: #6917
* Tests: the six timing assertions do not depend on the wall clock (#6917)
Six tests asserted on the wall clock. Their result depended on how loaded
the machine was and not only on the code under test: they passed on an idle
machine and failed when the test binaries ran beside each other, which is how
the suite runs (`cargo xtask test` starts every test binary at once).
CONTRIBUTING.md:196 says it: "Tests run beside each other on a busy machine,
so a test must not depend on wall-clock timing."
The change is confined to the six test files the issue names:
- geom: the tangent chain of a helix is a ratio (750 pieces against 3 000)
instead of a limit of 200 ms.
- io: the placement budget is spent inside the reader, so the clock is gone.
- ui-egui: the classification of many faces is a ratio (900 against 3 600)
instead of a limit of 10 s.
- engine: the clearance measurement drops its 30 s limit; the boolean that
gives up reports itself.
- engine: the fillet beside a modelled thread is a ratio (a 1 mm thread
against an 8 mm one) instead of a limit of 30 s.
- ui-egui: the window frame budget goes from 250 ms to 20 s, the limit #6072
gave its own probe.
The helper is the one #649 wrote, copied into the crates that need it, with
the noise of a run as a parameter.
* claim: #4971
* Thread: the refusal for a fine-only size says what to type (#4971)
M28 and other sizes without an ISO coarse pitch were refused as an
unknown thread, with examples of other sizes. Thread and threaded Hole
now say that the size has no coarse pitch and suggest two to give, such
as M28x2 or M28x1.5. The coarse table is unchanged.
* Thread: automatic sizing past M56 says what to type (#5055)
Automatic thread sizing only knows the ISO coarse sizes up to M56, so a
75 mm shaft was refused with "no metric thread fits a 75.00 mm
cylinder", although M75x2 and M75x3 work when typed. Past the end of
the coarse range, the refusal now says so and suggests two sizes with
their pitch, scaled to the diameter (a hole's size adds one pitch to its
bore). The coarse table is unchanged.
* Thread: turn a shaft thicker than a modelled thread down to its major diameter
A modelled external thread on a shaft thicker than the thread no longer refuses: the shaft
is turned down to the major diameter over the threaded length (run past a free end of the
face), then the thread is cut as before. The turned face is named F<n>:turned and the step
it leaves F<n>:shoulder:start/end. A shaft the part goes on around is refused rather than
cut into, shafts under the minor diameter and cosmetic threads on thicker shafts are still
refused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Thread preview test: an 8 mm shaft is turned down for M6; M10 still refused
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Fix large modeled threads and thin crest reconstruction
Helix stations follow the pitch (radial chord error under 1% of it, 48 to
720 stations), and the faceted rebuild retries at the BSP's precision when
the usual weld tolerance collapses a thin crest facet.
Rebased onto main as one commit (the branch's own commits touched UI files
that later moved to #2263 and #2264). Adapted to main's UnitVec3 thread
axis: `*k` in thread_groove and `*cylinder.axis` in the new flange test.
* Fix icon review revisions for same-timestamp edits
An M8 modelled thread in a 6 mm hole, narrower than M8's minor diameter, was
refused as "the face is too far from the thread's diameter". It now says what
is wrong and what fits, as a hole that is too wide already does (#995): "this
6 mm hole is too narrow for a modelled M8 thread (its teeth would fill the
hole); drill 6.75 mm for M8", with the thread that fits this hole when there
is one. A shaft too thick for its thread gets "make the shaft 8 mm for M8".
Fixes#2688
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* fix: a modelled thread that would cut nothing is refused (#995)
An M5 modelled thread in a 5 mm hole cut nothing into the nut: the
internal groove runs from the minor diameter out to the major one, so
with the hole as wide as the thread it lay entirely in the hole, and the
faceted cut only left the wall faceted with slivers ("the thread goes the
wrong way"). The fit check takes a 5 mm hole as an M5 hole.
- thread_groove measures how deep the groove cuts into the material
(hole wall out to the major radius, or shaft surface in to the root);
under a quarter of the basic depth 5H/8 the modelled thread is refused
with the measured depth, the tap drill (as solid.hole drills it) or
shaft size to use, and the size that fits the face, e.g. "this 5.00 mm
hole is too wide for a modelled M5 thread: it would cut 0.00 mm of the
thread's 0.43 mm depth; drill 4.2 mm for M5, or thread this hole M6".
- Cosmetic threads and their fit check are unchanged.
* test: pin the cut-nothing limit for coarse and fine pitch; show the hole size with show_mm
---------
Co-authored-by: MateuszSychXpl <151755914+MateuszSychXpl@users.noreply.github.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Fixes#602. Collinear-edge merging, piece naming and the dialog preview each work in one pass instead of quadratic loops; the issue's example goes from 86 s to 5.1 s.