Two more fillet cases, the reported part's concave arc and front top edge rounded together at
r5 and r7, with the same exact-box containment check (graded to 4e-5, the corner patch's
tolerance). On SMLib 2fc375f the corner patch stands 0.128 (r5) and 0.230 (r7) out of the
bar's front face (box y min -0.0699 and -0.1723): listed in KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A new fillet case, report-fillet-concave-arc-and-front-top-edge-together-solver-residues:
the reported part's bar (with the sketch solver's residues) whose sides run tangent into the
cylinder, its concave arc and front top edge rounded r2 together. The plane of the front face
bounds the whole body, so every blend lies within the unblended body's exact box (SMLib's tight
box); graded to 4e-5, the corner patch's own tolerance. On SMLib 2fc375f the corner patch
stands 0.0374 out of the front face (box y min 0.0205): listed in KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Its seams grade needs the continuity check to skip the body the round is not on. Fillet cases
wait for the new algorithm.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A square cut is the slanted plane's ordinary crossing; the cam's half turn is the quarter turn's
contact at a symmetric angle; the r15 slab stands inside the same coincidence tolerance as the r10;
the 90 degree unfold and the 40 degree flange repeat the 72 degree and 20 degree cases' formulas.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The sloped-basin chamfers and rounds at 0.5 mm rims repeat the 1 mm rim's regimes; two of the
three knife-edge chamfer tips, the r1 and box r3 curvature corners, the r1 tangent corner, the
1 mm pocket-rim and hole-rim chamfers short of the floor and the r1 together-round each repeat a kept case's regime
and grades. #854 moves to 851-chamfer-arc-top-edge-9-5, and the cases that cited a dropped one
cite the kept one or state its formula.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib keeps the skirt top's offset where its loops wind the other way under the opening, the
cavity's floor (the owner's ruling of 2026-10-31: build it; a lip thinner than the wall is no
break-through).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's inset now keeps only the regions that are cavity, not the one the offsets close where
they overlap (between the two faces of #545's 0.5 floor, round the up-down join's two empty
octants). The frame's core under the recess is hollowed to a sealed void, so the case says two
shells and its closed form, 21044 mm³.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's merge now intersects the offsets of an edge's faces where they could not be mated along
it (the hole's offset poking out through the half-round side's; tangency-labs/solidcore#1795):
one closed valid solid with the one face open, as the owner ruled.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib now offsets a vertex where four faces meet (two walls and two facets at the floor's
corners, four facets at the drain) to two vertices joined by a new edge (tangency-labs/smlib
branch smlib-shells). Both volumes match their closed forms. The pocket's lining, hanging from
the top's rim round the pocket, stands apart from the slab's outer walls with the cavity rising
between them to the open top: the case says two shells in the one body.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
926 (the chamfer ending on the boss's wall), the oblique cut's r0.1
round, the every-block r1 round (its seam with the cylinder is no
contact seam, after the blend_seams fix), the up-down squares' concave
chamfers and the shelled box's lip chamfer build with SMLib branch
smlib-blend-refusals (f8650b8 and later). 1207 r0.5 passes SMLib's check
on its rails now and stays listed for the next cause: its end rib on the
boss, which starts where the round and the boss are tangent.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>