* WIP: adopt the saved model on open (#3053)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* WIP: tests
* WIP: bench-open opens as Open does
* docs: opening from the saved model
* Tests: an edit after opening evaluates from the feature it changes
* clippy
* Read SOLIDCRAFT_NO_MODEL_CACHE through the env helper
* Open: no picture from the model when the model itself opens; cancel test evaluates
* Saved model: bodies passed through found without writing their record; states list runs of bodies
* Adopted results go into the evaluation cache: an undone edit, or the marker rolled forward, takes them again
* Model cache size guard: the saved model's writer
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* geom: UnitVec3; a face's analytic axes and normals are unit by type
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* geom: UnitVec3 adds to and subtracts from a Vec3
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* kernel, doc, engine: cylinder axes and measured normals held as UnitVec3
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* kernel, engine: functions that take a unit axis or direction say so by type
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* doc: a face's normal goes to Plane::from_normal as is
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* kernel, doc: main's new cylinder helpers take the face's axis as a UnitVec3
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Reword comments, docs and package descriptions so they describe SolidCraft's own behaviour instead of comparing it to another product. The trademark notice, the commercial-CAD rule and the navigation preset name stay as they were.
Co-authored-by: Claude Sonnet 5.5 <noreply@anthropic.com>
* Action matrix regressions of #1255: knuckle rounds, thin holes, a 45° flange hole, an axis after an edit
- Curve blends: past the end of a curved edge the run of sections along the end
tangent wrapped round the ring of centres; it is shortened while it still
crosses the end face (the hinge knuckle's cap rounds at 0.728 mm).
- Boolean retry guard: each body's volume is measured finer than its smallest
radius, and a volume out of bounds is measured again ten times finer before
it refuses (a 0.133 mm drill measured -30272 mm³; a plastic part's coarse
mesh was off by more than the slack).
- Sheet metal: a drill cap's certificate allows the evaluation noise its fitted
tilt shows (a hole square to a 45° flange).
- Construction geometry on a named face uses the face found by name, not a
second pick at its nearest point (an axis through a corner round after a
parameter moved it).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Retry guard: measure the target, tool and result at one tolerance
Measured at different tolerances, the chords' error on the faces they share
didn't cancel: a blind hole in a long D-profile bar measured 20 mm³ more than
the bar.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Action matrix baseline from this branch's full run: 37 actions pass again, none fewer
Blessed with cargo xtask action-matrix --from DIR --bless from the 16 shards of
run 38673859774.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
inputs_mut, inputs and expressions are now built on one exhaustive walk (walk_exprs / walk_exprs_mut) instead of two hand-written matches over FeatureKind. inputs() no longer clones the feature, plane chains are walked with the same nesting cap for inputs as for expressions, and a new variant without a walk arm does not compile. A golden record of every variant's expressions guards the walk.
A construction plane built from model geometry resolves each of its sides
through the document again. That hop restarted the recursion depth at 0, so a
plane that is its own side never exceeded depth 1 and the 32-level cap never
fired: a ~600-byte design file recursed until the stack overflowed and the
process aborted, which no panic guard can intercept.
Carry the depth on the construction context so the geometry arms continue the
caller's count instead of restarting it.
Fixes#143
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
(cherry picked from commit 4bca1d49f27dfe9ef0140132746e1c7415daba8e)