Where the round meets the open bottom the cavity's wall steps down along the bottom's normal, so the
round meets it at 90 degrees and the opening is exactly the picked face. The cases are renamed and
graded on the exact volumes, and come off the shell known-failing list.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib keeps the skirt top's offset where its loops wind the other way under the opening, the
cavity's floor (the owner's ruling of 2026-10-31: build it; a lip thinner than the wall is no
break-through).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's inset now keeps only the regions that are cavity, not the one the offsets close where
they overlap (between the two faces of #545's 0.5 floor, round the up-down join's two empty
octants). The frame's core under the recess is hollowed to a sealed void, so the case says two
shells and its closed form, 21044 mm³.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib's merge now intersects the offsets of an edge's faces where they could not be mated along
it (the hole's offset poking out through the half-round side's; tangency-labs/solidcore#1795):
one closed valid solid with the one face open, as the owner ruled.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLib now offsets a vertex where four faces meet (two walls and two facets at the floor's
corners, four facets at the drain) to two vertices joined by a new edge (tangency-labs/smlib
branch smlib-shells). Both volumes match their closed forms. The pocket's lining, hanging from
the top's rim round the pocket, stands apart from the slab's outer walls with the cavity rising
between them to the open top: the case says two shells in the one body.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The shell unit tests that checked geometry become shell rig cases built through
commands: the trough and the pocket whose floors fall 1 deg to a central drain
(the pyramid made as two triangular prisms intersected, in place of
convex_polyhedron; the cavity integrated exactly over the cells where each moved
facet is highest, sharp inner corners as the ladder's tier 09), the box opened at
a bottom rounded R2 and R2.4 (refused: the rim would have no thickness) and R1.5
(built, exact volume), and the plate with a hole through its arc side. Four
action-matrix shells that regressed (issue-616's lid, the ring-cut frame, the
filleted shelled box shelled again, the up-down join) get small cases too. The
ones that fail today are on KNOWN_FAILING with their cause, and the unit tests are
removed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
- #58: a fillet's tangent-point step no longer depends on the blends before it (solidcore #1173).
- #59: the fillet clean-up keeps the target's edges and faces by a mark, not by address (#1176).
- #60: capi test, a line projected through a sphere's poles meets itself smoothly at each pole.
- #61: offset faces removes a step wall the move closes to nothing and merges the two tops, so
shell/cov-replace-face-step-onto-the-higher-face builds.
- #62: thicken puts a flat side wall on its plane (solidcore #1599), so a cylinder sheet's end
rings are planes: surfaces/cov-thicken-cylinder-sheet-symmetric-tube passes.
Both cases leave KNOWN_FAILING.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
kernel-rig.yml builds solidcraft-cli once (release, SMLib prebuilt; sccache on a sticky disk
that only pushes to main and develop commit) and hands it, with the rig's runner, to a matrix
of eleven shards: the ten areas of tests/kernel-cases/, each against its KNOWN_FAILING, and
the ladder against its golden. One path filter covers the kernel surface; drafts skip; a new
push cancels a pull request's old run; merge groups always run it, and the release gate calls
it. The areas other than fillets get a KNOWN_FAILING with only its header, to be seeded from
develop after the SMLib pin bump.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>