Three conflicts:
- crates/smlib flat.rs and export.rs: #8526's export copies the C++
arrays by id range; the ranges now run to the ball-patch arrays
(FACE_DEFINITION_REAL_COUNT, FACE_DEFINITION_REALS), with
WIRE_EDGE_NURBS_FORM (35) and FACE_DEFINITION_REAL_COUNT (36) both kept.
- tests/KNOWN_FAILING_TESTS: solidcore's lines and develop's, each test
once; tests/KNOWN_FAILING_TESTS.smlib takes develop's SMLib a18bbe5 lines
too. The first full run trims both.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
On SMLib v1.1.0-alpha, 06/018 makes 597 or 594 edges from the same input:
the union's post-process keeps pointers to edges it has deleted. A golden
entry's `unstable` reason makes the gate compare that case's status only
and name it in its output; recording keeps the reason, and only an edit of
the golden removes it. v1.1.0-alpha.1 fixes the cause and removes the mark.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
Fixed (off the known-failing list): the Mixed corner's peg cases and the concave arc with the front top edge (smlib #123), and the 40° boss junction (smlib #124). Eight cases in all.
New failures, recorded as they are, each with its reason. They passed on f916a8d.
- **Six cases grade a blend seam G0 where G1 (or G2) is wanted,** at the end of the round's contact seam, after smlib #124's End at a smooth vertex. Two of them also shift in volume.
- **Four cases come back unsupported** after smlib #125, which leaves setbacks to the Setback's corners only.
- **Ladder 07/012** makes 9 faces, 20 edges and 13 vertices, where its golden had 8, 18 and 12. Its golden entry is the new result, with the reason added.
Whether each change is by design or a defect is being established. A defect is fixed in solidcore, where the End and the Setback are being brought over (#2364, #2365), not in the frozen SMLib.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
SMLib's flat arrays now carry the corner of three equal rounds as `SURFACE_BALL_PATCH` (kind 6): its net as a NURBS face's block, with its sphere's centre and radius as its definition (ids 36 and 166). The record reads it as `ball_patch {center, radius}`, a label like the analytic kinds, with the net as its `nurbs`. A plain sphere with a form won't do: the net is not a piece of SMLib's sphere NURBS, so SMLib's `IsNurbSurfaceSphere` would refuse it.
Written back, a ball patch is kind 6 with the same definition, which SMLib takes once its net is certified on that sphere. Elsewhere:
- Offsets classify it as its sphere, so its offsets stay exact and collapse at the centre.
- Face kinds count it as a sphere: fillet_three_edges_at_a_corner's corner is now `sphere`, no longer `other`.
- STEP, which has no ball-patch entity, gets the net as the face's B-spline surface, pcurves included.
- Iso curves and SSI of the label are refused; the face's form is what evaluates.
Test: a_rounded_cubes_ball_patches_go_round_with_their_spheres. The cube's eight corners are ball patches about the corners pulled in by r. Points of each patch lie on its sphere to 1e-12. The patches are kind 6 again after import, with the same definitions bit for bit, and the closed-form volume holds.
Format: pending/ball-patch-faces.rs. Docs: docs/native-brep.md and the rig README's `surface_types` (`ball_patch`).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
solidcore, the pure-Rust kernel, is always built and stays the default. The
`smlib` feature (apps, engine, kernel; solidcraft-smlib's `native`) now has
to be asked for to compile and link SMLib: the app, the CLI and the web app
drop it from `default`, and solidcraft-gpu's dev-dependency no longer forces
it on. Without it no C++ toolchain, fetch-smlib.sh, prebuilt or build.rs work
is needed.
On a build without it, asking for the C++ kernel (SOLIDCRAFT_KERNEL=smlib,
diagnostics.kernel, the rig) is refused with Error::NotBuilt, which now says
"this build doesn't include the C++ SMLib kernel; build with --features
smlib", and SOLIDCRAFT_KERNEL=smlib logs that once. `cargo xtask
kernel-cases` builds the CLI with --features smlib only when --kernel smlib
or both asks for it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SdcgEtwSrdwZxqTQp5MfnU
- Cut To the far side of a curved wall (#8634): the tool stops past the first crossing of the
face ahead of the profile; SMLib's whole bore is one face that a line crosses twice, so the
single-crossing rule found none and the cut took nothing.
- Clearing view analyses goes through refresh_display, as main's #10687 made the others, so an
open feature editor keeps OK and Cancel after Zebra.
- vi, a complete catalog on main, gets the setback-too-short message.
- fillets/KNOWN_FAILING: 4782's cause is now its continuity check (SMLib f916a8d builds the
expected volume).
- Known failing, as main's tests assume truck: the spline wall's spans as one mesh patch, a
hole touching an edge at a point leaving one body, and a copy of a copy's triangles matching
a fresh mesh.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SdcgEu4Lr3moCCisdZShKz
1213: the loft is a cubic skin through the five sections (ellipses between
them), not a torus; its volume 131601.597487935 by quadrature less the exact
rolling-ball removal 233.662461919 gives 131367.935026 (was a Pappus estimate
on a torus, 131360.148, at rel 5e-4).
4782: the section's area in closed form, 25 pi/3 - 5 sqrt(75) + 25, so
V = 630.2934873 (was a grid estimate, 630.293125).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SdcgEu4Lr3moCCisdZShKz
Rig (fillets/KNOWN_FAILING.solidcore): the two 851 rows develop now rounds with their tangent
chain fail 1001 as on SMLib; the pipe on a plate's curvature round is graded to 5e8c9c1's
section, which solidcore has yet to port. Tests (KNOWN_FAILING_TESTS): main's box STL and
boss-torus tests, as on SMLib; the box-corner test and four C++ comparisons that expect
5e8c9c1's Ball corners and rounds.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SdcgEu4Lr3moCCisdZShKz
smlib b7e83cd7c: origin/develop (SMLib pin 5e8c9c1) and origin/main.
Conflicts, both sides kept:
- Cargo.toml: solidcore's pinned solidcore dependency beside main's solidcraft-testkit.
- tests/KNOWN_FAILING_TESTS: solidcore's default-kernel list kept (refreshed from this
merge's run in a following commit); smlib's list for SMLib 5e8c9c1 becomes
tests/KNOWN_FAILING_TESTS.smlib.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SdcgEu4Lr3moCCisdZShKz
The rig on solidcore: 982/1014 pass (968 at pin 13). Fourteen cases
come off the lists (the curvature rounds, the variable cone, 3604's G2
swept tool, the curvature fillet after a fillet). Six remain with new
causes: the G2 pocket corner and the bar corner's three edges (two) G1
at one seam and the cylinder-side G2 corner not closed, as on SMLib;
the oblique three-edge corner refused for its mixed wedges; the mixed
corner refused as on SMLib.
Tests (nextest, ci profile, PR filter): 34 come off
KNOWN_FAILING_TESTS (curvature and variable rounds). three_rounds_at_a_corner
is listed (its corner's variable transition at 0.144°, as on SMLib
d01d7b0); chord_and_variable_fillets now fails on its waist law's
corner (solidcore#430).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SdcgEu4Lr3moCCisdZShKz
On the CI runners the boss root and the hole rim, both size-2/size-1 curvature rounds, build
correctly but take more than 180 s: the order-2 section's span certificate and the round's
definition are evaluated station by station. The per-case limit is the one the thread cases use.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
With the tangent chain on, 016's and 018's r3 runs on along the r5 round's end arc and down the
vertical edge, so the third pick (60, 40, 8) is 3 from both of that round's contact lines and
names no edge: refused, asking for a point along one edge. The corners they were made for are
020 and 021 (the r3 alone), whose golden entries are 016's and 018's (021 measured on f12a101).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
851-fillet-arc-then-top-front and 851-fillet-top-front-then-upright: with the tangent chain on,
each R2 chain runs along the end curve of an R2 round on a curved face (the arc round's end on the
front face; the first round's end on the wall), where the rolling ball sits on that round's own
centre line, so the piece is the ball about (39.2538, -19, 8): the three-edge rolling-ball corner.
SMLib fails with status 1001; the same piece on a plane end arc builds (front-left upright).
Expectations unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
- every-fillet-after-fillet-curvature-front-then-side-r3: the side edge's chain runs round the
first curvature round's end curve, whose radius of curvature has a weighted mean of 3 (its
setback) and is unbounded at the ends, so somewhere below 3: the size-3 blend's contact line
folds back on itself. Refused, "larger than the faces beside its edges allow", as ladder
07-fillets/016's r7 on the r5 arc. (It was solid or refused for running on tangentially.)
- every-block-cylinder-tangent-concave-arc-r2-no-tangent-chain: the chain takes every piece of
the half circle and ends at the convex edges it runs on into; it builds the analytic 19091.9620,
so the outcome is solid (the refusal alternative was the chain-off one's).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
With the tangent chain on, two cases round more than the edge they pick, and their old
expectations were the single edge's:
- 1207-fillet-box-end-edge-into-unblended-round: the r1 chain is the end face's top edge, the r3
round's end arc and the back upright; 34 A + (pi/2) A (3 - c) by Pappus on the arc:
V = 7953.139216 (it built 7953.139216, the old 7957.505 passed only inside 1e-3), 10 faces.
- 851-fillet-top-front-then-front-left-upright: the upright's chain runs up the first round's
end arc on x = 0 and along the left top edge, so the corner becomes the R2 ball's eighth:
V0 less the first round's spandrel to the wall (35.344727) less 27 (4 - pi) + 2 pi/3:
V = 9530.777979 (built 9530.777987), 10 faces.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
fillets/every-block-cylinder-tangent-concave-arc-r2-partial-chain: the pick takes one piece of the
concave half circle, which SMLib splits; with the chain off its other pieces are left out, and the
blend is refused at the piece's end (the base gate's outcome). With the chain on the case rounds
the whole half circle. The copy keeps its expectation, to be re-derived.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
Where a case's point is one edge of a tangent chain rounded alone, a copy keeps tangent_chain
false as its own case (SMLib rounds exactly the picked edges, ending at the smooth vertex); their
expectations stay as they were, to be re-derived:
- fillets/1207-fillet-box-end-edge-into-unblended-round-partial-chain;
- fillets/every-fillet-after-fillet-curvature-front-then-side-r3-partial-chain;
- fillets/1207-fillet-bar-top-edge-after-boss-arc-round-partial-chain, renamed from
...-no-tangent-chain: with the chain on it is exactly 1207-fillet-bar-top-edge-after-boss-arc-round,
which the rig already has;
- ladder/07-fillets/020 and 021, the r5/r3/r7 and r5/r3/r2 corners (016 and 018) with the r3 on
its edge alone: with the chain on, the r3 runs on along the r5 round's end arc and down the
vertical edge the third round was to take.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
The owner's ruling of 2026-11-01: the rig and the ladder round with tangent_chain true, how a
user's default pick behaves. The 38 fillets-area recipes and the ladder's 07-fillets/016 and 018
that passed false now pass true. The shell recipes keep theirs: a shell's tangent_chain is its
open-face chain, a different feature.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01DtL5M41G8Nua7HvuFPZkmJ
SMLib builds a variable round's law corners as its balls' union (the corner
ball's zone at a dip, the sides' crossing at a peak): the kernel's corner
through a middle point (39.5410) and the crate's 4 -> 2 -> 4 law (39.5421) pass.
Rig 1207 (the bar's top edge rounded after the boss's arc, r0.5) builds and
grades on the same SMLib; it failed on c820346.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Rebuilt from the trapped nextest run (11497 ran, 51 known failing, no regression) and the rig on
solidcore (968/1014). The curvature fillets (solidcore#2250, #2260) and variable-radius fillets
(solidcore#2250, #2262) are refused, so their tests and rig cases are listed as such, the
rig's as [unsupported]; a law with a corner stays refused as before (solidcore#430). develop's
new junction and turn cases fail on solidcore as on SMLib d01d7b0.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SdcgEu4Lr3moCCisdZShKz
fillets/report-peg-step-front-and-concave-rounds-together-r2 no longer
fails with 1001 on solidcore: since solidcore#2198 (cb9e544ab, WR-641) an
extended rail end whose section cannot be solved is skipped, and the round
builds as fillets/report-peg-front-and-concave-rounds-together-r2, the same
peg not written to STEP, already does: a seam G0 at (32, 2, 10) and the
tight box 6.5e-3 below the front face y = 0, where the exact box is
(0, 0, 0) .. (48, 16, 20). The case stays listed, with that reason.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SdcgEu4Lr3moCCisdZShKz
At the default 1e-3 the great circles' volumes (4e-6 off) passed too. SMLib builds each within
1.6e-7. The golden takes the new volumes and areas; counts unchanged. The G2 corner test listed
as failing passes on SMLib's step 3 and leaves the list.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The smlib crate's laws and ladder 005, 006, 007 and 012 take the volumes the balls' envelope
removes; the law with a corner is its own test, listed as failing until the corner step.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Four are listed with their causes: the equal-pipe tee (its exact conic-pair rounds meet at the
ellipses' crossings in a corner the old corner code cannot join), the tilted bosses (1001, before the
blend rework too) and the Y junction (refused for room at its triple points).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
A round's spandrel A = (1 - pi/4) r^2 and its first moment about its wall M = r^3 (5/6 - pi/4):
Mitre adds L A -+ 2 M per edge (cut at, or run on to, the corners' bisector planes), Swept turns
the section about a convex corner's edge, (pi/2) M a corner, and refuses a concave corner rounded
less than the ball. The pocket's tangent chain round its R3 corners is a torus each. Graded to
1e-7, where Mitre and Swept differ by 6.6e-6. The Swept cases are listed until solid.fillet
takes a turn.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
On the round's rails the order-2 section takes off what the ball's circle does: (1 - pi/4) s^2 at a
square corner, first moment 0.0474559669443 s^3 (w = -0.5252123889). The kernel and engine tests
and the curvature rig cases take their volumes from it by their own methods; the pipe on the plate
from its own wedge (70.52878 degrees, w = -0.8544103493). The G2 corner patch's seam test is listed
until the corner step.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
SMLIB_BLEND_CURVATURE's section is now the order-2 G^n section at thumbweight 0. Between two
planes square to each other it cuts A = 0.154192655384275 s^2 off the corner, its first moment
about either face 0.0291753295725360 s^3 (Green's theorem on the section): the curvature cases
built on that corner (862, 2708, every-box-edge, every-hole-top-rim, every-l-bracket,
every-block-cylinder-crease, the three-edges-at-bar-corner reports, 3604's fillet) take their
volumes from it by their own methods, the peg's front blend 23.3237146876 (its section along x
up to the wall). Between planes the section's t^3 term vanishes (their feet are linear in the
distance): the box edge case is exactly G3. The boss root is a certified fit, G3 to the plate and
G2 to the wall at Continuity Analysis's tolerances: at least G2. The boss root and the pipe on
the plate pass on SMLib's section and leave the known-failing list.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Eight fillet cases for the blend's cross-section by its order of contact with the faces, each
graded on its analytic volume at rel 1e-7 and its exact continuity (the order, and not the next):
- a box's top back edge chamfered 3 (G0), rounded r3 (G1) and curvature-rounded 3 (G2): the
areas cut off the corner s^2/2, (1 - pi/4) s^2 and 113/756 s^2, the last by the default
thumbweight's definition;
- a pipe R10 dipping into a plate, its concave edge chamfered 2 (the chord between the contacts of
the ball SMLib rolls for that setback, radius 1), rounded r2 and curvature-rounded 2, each
section's added area by Green's theorem along the plate, the section and the pipe's arc; the
order-2 section is built from the faces' feet of the point at distance d from both, which on
the pipe are not linear in d;
- a boss root curvature-rounded 2, the square corner's section revolved (Pappus);
- a variable round r1 to r5 along a box edge (rel 1e-5): the balls' envelope is a circular cone,
and the volume is the cone's sections integrated along the edge.
Three fail today and are listed: the two curvature rounds whose faces are not a square corner of
planes (SMLib's quintic blend curve, not the order-2 section: rel 6.5e-7 and 1.2e-5) and the
variable round (great circles, not the envelope's: rel 4.8e-5). The other five pass on SMLib
7ac037e.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
They pass now and are un-listed: the convex-edge chamfer refused as too
large (solidcore#2175), the thickened spherical cap (#2174), the
thickened B-spline patch (#2111), the extrude reading back the region
clicked (#2177), and the rig's round of cylinders touching at a point
(#2110). solidcore now passes the six self-crossing intersection cases
it missed against the C++ kernel (ssi_split_curves_at_singular_points:
off, they miss again), so the corpus test asks for no miss at all.
Listed: the moved-top offset test's C++ comparison, as solidcore's
offset edges keep their tolerances and the pinned C++ kernel's don't
(both stay 1.2e-8 to 3.1e-7 off the closed form). The tabbed plate test
gets past the corner arc alone (#2176) and fails later, on the rim and
a corner arc rounded together, each of which builds alone.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SdcgEu4Lr3moCCisdZShKz
The per-family runs (`solidcore[boolean,measure]`) needed the process to mix kernels, which the
kernel choice is about to stop doing. --route is refused with a message, so a script that still
passes it does not run as something else. The report's labels went with it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01MNXLXkZLQ6T7TSi4wswcmk
From the rig on this branch, 949 of 974 and one timeout: threads/3368-two-faceted-prisms-cut-then-joined
is not listed, it takes 160 s alone against the 180 s limit and passes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01MNXLXkZLQ6T7TSi4wswcmk
Where the round meets the open bottom the cavity's wall steps down along the bottom's normal, so the
round meets it at 90 degrees and the opening is exactly the picked face. The cases are renamed and
graded on the exact volumes, and come off the shell known-failing list.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>