sketch.intersection_curve (LinkSource::Intersection, crates/doc/src/
project.rs) intersected the two bodies' display meshes triangle by triangle
and chained the segments into polylines: a curve known only as points, off
the true intersection by the meshes' chord.
kernel::meeting_edges(a, a_face, b, b_face, chord) takes each side whole or
as one face (that face alone as a surface body, surfaces::taken), tags both
and imprints the first by the second in SMLib (smlib_imprint: "each of its
faces that `tool` meets cut along the intersection", capi/include/smlib.h).
SMLib intersects the faces' surfaces and trims each curve to both faces, so
the edges the imprint makes are exactly where they meet; its own history
says which they are (an edge no edge of either operand became). Each comes
back as its record curve on its interval, from SMLib's export of the
imprinted body, with its points from that body's mesh at `chord`. Sides that
do not meet give none.
The intersection link now stores each edge as a wire with its exact curve
(Wire::exact, the existing WireCurve; no new type or format change), its
points at 1/1000 of the larger body. project3d::mesh_intersection, its
triangle/triangle test and segment chaining go; project3d::mesh_of becomes
part_of (the body and, for a face reference, the face index).
Needs in crates/kernel/src/lib.rs (the coordinator's): `mod intersection;`
and `pub use intersection::{MeetingEdge, meeting_edges};`.
Not built: base in progress (kernel-smlib/no-truck 513ebe47 does not build).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
truck-modeling, -topology, -shapeops, -stepio and the vendored truck-geometry, -meshalgo,
-shapeops, -stepio and matext4cgmath (with their attribution rows and vendor notes) are removed.
The kernel-cases runner has one kernel, SMLib, and no build-mismatch check; a modelled thread is
cut by SMLib's exact screw-swept groove (the faceted groove path is gone).
(not built: base in progress)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
A sweep path through 3D sketch curves sampled every planar sketch curve in it
into a 0.01 mm polyline, and took every linked 3D curve as the points its link
stored, so SMLib got a many-cornered polyline (and refused a smooth one). Now:
- a planar sketch curve in such a path is its exact segments
(PathPiece::Segs of PathSeg::of_sketch over exact_segs);
- a linked curve whose source has an exact curve keeps it: Wire::exact holds
the record curves (WireCurve: schema 4 curve + interval) end to end along the
wire, set with the wire when the link is resolved: an included body edge its
record edge (kernel::brep_record), an included sketch curve leaving the plane
its segments (kernel::sketch_record_curve). Wire::map carries them with a
placement. The sweep follows them through kernel::curve_path (line, arc,
ellipse as rational quadratic spans, polyline, B-spline as Bézier spans).
- curves known only as points (projected onto a face, intersection and iso
curves: the link resolves them on the mesh) stay points.
Kernel, for the sheet and blend ports: planar_face_record (a profile face as a
schema 4 sheet record with exact pcurves), smlib_sweeps::chain_curves (a
segment chain as SMLib curves), body_from_record (any record into SMLib,
checked), sketch_record_curve; record curves from design files are checked in
curve_path. Format: pending/wire-exact-curves.rs.
lib.rs (coordinator): export SpaceBezier, curve_path, edge_path,
sketch_record_curve and planar_face_record from the kernel.
(not built: base in progress; kernel and sketch check clean, doc not reachable)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
A closed path was always followed from the start of its first picked curve,
wherever the profile stood on it. A profile drawn at the middle of a line was
then carried round the path standing off it by the distance between the two
(walls offset, the rounds turned the wrong way, on both kernels). Now the
closed chain begins where the profile's plane crosses it nearest the profile,
the curve there split in two (or at the joint there); open paths and paths
that already start on the profile's plane are unchanged.
Test: a 4 x 3 profile at the middle of the bottom line of a rounded rectangle
swept round it: Pappus volume and the tube within 2 mm of the path.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
A drawn 3D spline reached the kernel only as its sampled polyline (Wire.pts), so SMLib refused
to sweep along it ("not supported yet: SMLib sweep along a smooth path of points"). The doc
holds the spline's fit points; the curve is the centripetal Catmull-Rom spline that
fit_polyline samples. Each span of it is a cubic (Barry-Goldman), and its derivative at a fit
point depends only on that point, its neighbours and the two knot intervals, so neighbouring
spans share it: the spline is exactly one cubic Bézier per span, C1 across the spans.
- geom: catmull_rom holds the curve: samples() (fit_polyline's arithmetic, moved verbatim;
sketch::fit_polyline now calls it) and beziers(), the exact spans; ArcLength on CurveN
(Gauss-Legendre per knot span, Newton for the parameter at a length).
- kernel: PathSeg::Cubic, a cubic Bézier in space (the 3D counterpart of PathSeg::Curve, which
is planar), with its arms wherever PathSeg is matched (start/end, tangents, length, point at
a length, turn, SMLib curve as a degree-3 NURBS, halving). PointPath / PathPiece carry a path
through 3D sketch curves: polylines as points, drawn splines as their fit points (reversed
when the path runs them backwards); PointPath::segs gives SMLib the spans and the lines;
sweep_point_path_with sweeps it (SMLib through sweep_with, so corners, twist, scale, rails and
orientation take the existing routes). A smooth polyline piece (a projected or linked curve,
which the kernel only has as points) is still refused on SMLib.
- doc: path_points builds the PointPath (a wire with three or more fit points is a spline
piece); solid sweep and pipe call sweep_point_path_with; rails, surface sweeps and curve
networks take its points as before.
Checked in scratch (not committed): the spans pass through every fit point and every
fit_polyline sample at its parameter (1e-12), C1 at the joints and round a closed spline;
samples() is bit-identical to the old fit_polyline over 1180 random open and closed inputs;
SMLib sweeps of a radius-2 circle along an open spline and round a closed one match
pi r^2 L (L by independent quadrature of the curve's definition) to 1e-7 and 3e-8.
sketch/wire.rs: the existing closed-spline test reads SPAN_SAMPLES from its new home.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
A Join with one target takes every tool, whichever it meets, but it grew the
target by one tool at a time: each union took the whole result so far, and
each step first meshed it to see whether the tool met it (which with one
target decides nothing). n tools cost n^2 in every per-body step of a
boolean (converting the operands, checking the result, exporting it back),
whichever kernel runs it: a combine of 64 separate pegs (booleans/3455) took
400 s on SMLib, of 36 lofted blades and a disk (crashes/2992, sweeps/1856)
485 s and 97 s.
With one target, the target and the tools are now unioned pairwise, level by
level, so each body takes part in about log2(n) unions. The result is the
same union under the target's name, with the lineage of every union. Several
targets keep the absorption order they need. The doc and engine join and
combine tests passed and failed on SMLib as before (measured before the
rebase).
Not built: base in progress (rebased onto kernel-smlib/no-truck 41adb372).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
Body::mesh / mesh_plan / mesh_of and MeshTolerance (chord, display, display_of, export_of)
replace tessellate, tessellate_with, display_mesh*, display_plan*, reference_display_mesh_angular;
every caller in kernel, doc, engine, io, ui-egui, gpu and the CLI renamed mechanically; the
truck-mesher fallback, mesh_shells*, refined* removed; Body::new orients from the planner;
truck-meshalgo dropped from Cargo.toml with the tests of its hooks. Still to fix: trait imports
in tess/*, splitface/lumps/preview/step_in/boolean_record meshalgo uses, measure.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
Through SMLib, in place of "not supported yet":
- A sweep along a path with corners: each smooth run swept on its own and
the runs joined at each corner in a mitre (each run swept on straight past
the corner and cut back to the plane halving it, where the next meets it
face to face), including the corner where a closed path closes; only
moving along the path, the runs meet on the profile. History: walls from
their segments (found half-way along each run), caps where the path ends.
- A free-form path curve (a spline's Bézier pieces, conics) reaches the
kernel as PathSeg::Curve, its exact piece, instead of the sketch's
polyline of lines: SMLib sweeps along the curve itself; truck's sweeps
flatten it as before (now the piece's own polyline within 0.01 mm, which
turns ladder 04/004 into a pass for truck too). Patterns along a path
flatten it and measure as before. A sweep that twists, scales or follows
rails places its stations by length along the curve.
(Such a controlled sweep still refuses a path with corners.)
- A loft through sections with holes: each section's outline and holes are
one SMLib profile, the holes matched as for truck.
- A loft to a point: SMLib's pyramid (smlib_loft_to_point).
- A draft extrusion with a straight foot: the foot's prism and the drafted
part (sloping from the foot's top to the far end the taper gives) joined
face to face; each segment names its foot and its sloping wall.
Cases now passing on SMLib: booleans/3633, sweeps/1184, 2435, 3111, 3006,
3505, 561, 96, ladder 04/003 and 004.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
After a parameter edit, a feature's stored face point is moved onto the
face its name finds. That used the face's nearest point to the old pick,
which lies on the face's boundary whenever the pick no longer lies on the
face: a shell opened at the end of a bar picked (150,15,10), on the edge
it shares with the bottom face, so truck opened the wrong face and SMLib
refused the pick (#2531).
FaceHit::pick_point keeps the point where it still lies on the face clear
of its edges, and otherwise takes the face's nearest point among points at
least a margin inside its triangles (a few pick tolerances, capped at half
the roomiest triangle's inradius on narrow faces).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017itGh5fpMEousnZ91cYcVt
On SOLIDCRAFT_KERNEL=smlib the thread's groove (the ISO 68-1 trapezoid, as before) is a B-rep
screw sweep (kernel::sweep_helix, SMLib's screw sweep) cut from the body by the B-rep boolean,
whose history carries the threaded face's names on. Truck keeps the faceted groove and the
faceted boolean. thread_groove_shape holds what both build from; the size checks before it
(a hole or shaft off the thread's size is refused with the size to use) are unchanged, so
neither kernel fits a thread to a face that is too large or too small.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
The corpus naming test (next commit) records what every stored face and
edge name resolves to, and must find it exactly as a rebuild does. Three
lookups were crate-private: `locate_face_on_body` (a feature's face
points, tried on the body the feature names first), `blend_target` (the
body a fillet or chamfer rounds) and `Document::anchored_face_indices`
(the faces a face-attached sketch is on). Visibility only; no behaviour
changes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
FaceOrigin, Change, FaceProv, Side, EdgeOrigin, EdgeProv and History move
unchanged (fields, serde derives) to solidcraft-geom, so a backend can
report history without depending on solidcraft-kernel. The pure methods
(composition, renumbering, count checks, mark_shared_split) move with
them and return brep::history::Failed, which converts to
KernelError::Failed with the same "history: …" message.
What needs a kernel body (History::identity, check, face_sources) stays
in the kernel as the BodyHistory trait; solidcraft_kernel::history
re-exports the types, so existing paths keep working.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QWhMwdqJYQKQq8RCLSL1LT
Evaluation and placement never read appearances, yet an appearance edit
re-evaluated the model and placed every occurrence again. A whole-document
proof that only appearances changed now takes the existing render-only refresh,
which keeps the model and retargets the world-placement cache.
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
Naming a placed body scanned every occurrence and body of the design, so the
world state and every caller naming all placed bodies grew with bodies times
design size. WorldNames indexes the design once and names each body in time
proportional to its occurrence path; one naming routine serves both it and the
single-body scan. Names are unchanged (a test compares them with the scanning
implementation).
Co-authored-by: Claude Opus 5.5 (1M context) <noreply@anthropic.com>
* claim: #5641
* Cone primitive: solid.cone with base and top radius (#5641)
A cone or truncated cone placed like the cylinder: base centre, axis,
base radius (or diameter), top radius (0, the default, is a full cone)
and height, with the new body / join / cut / intersect choice. It is
built from what the kernel already exposes, a revolve of its half
section about +Z through the origin, moved into place. Toolbar entry
after Torus, a Cone dialog that also places it on a picked face, Edit
Feature, a timeline icon, pending UI strings and attribution, and one
pending design-format change.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6070
* Sketch: a changed length dimension keeps its start point, so a side grows from its first corner (#6070)
Changing a dimension's value re-solved its sketch as the smallest move from
the stored positions, which splits the change between both ends: a
rectangle side set from 40 to 60 mm grew 10 mm each way. parameters.change
now first solves a sketch whose length dimension (distance, horizontal or
vertical distance, line length) the parameter drives with that
dimension's first point held, and stores the result, so evaluation has
nothing left to move. Where holding it can't solve (a symmetry moves both
ends), evaluation solves as before.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #4784
* Part properties: one table of keys, each with its scope, check and label (#4784)
SolidCraft's part-property keys (project, part number, revision, author,
organization, description, licence) were declared once but listed again
by hand in each command, error, dialog and window. They are now one
table, metadata::KEYS: each row has the key, where it may be set
(Scope: the design, a component or both), how its value is checked and
the message id of its label. A new key is one row.
Metadata::set is told whose metadata it changes (Owner::Design or
Owner::Component), and a key is taken where its scope covers that
owner. is_well_known, both set commands, document.metadata,
component.metadata, the refusals, the Design Properties dialog and the
Bill of Materials window read the table; the hand-written lists are
gone (WELL_KNOWN, the label match whose fallback named any unknown key
"License", the window's three labels). metadata::BOM_KEYS names, in
column order, the keys a bill of materials lists for each part:
component.metadata returns them, component.metadata.set takes each as a
parameter of its own and the window edits them; a test keeps each one a
row of the table that a component takes. Free properties use the keys'
text rule (metadata::check_text) instead of a copy of it. The params
docs point to document.metadata's properties instead of repeating the
keys.
Every key accepted before still is, on the design and on a component.
Two things change:
- a refused key or a full metadata on a component says "part property"
("`bogus` is not a part property: …", "part properties are limited
to …"), not "design property";
- changing the design's own properties no longer evaluates the model.
The fields that change no geometry are named once,
Document::with_part_properties_of: the design's metadata, and each
component's metadata and free properties. It compares them first and
copies the design only when one differs, as before.
The shortcut is for a session's own edits only. A command that gives
the session another design (doc.open, file.new, doc.recover: through
Session::replace_design, which now counts them) is refreshed in full,
however little the new design differs from the one before, so its
joints are solved and its occurrence state pruned. Before, opening a
design that differed from the open one only in render settings or
component properties skipped that; with the design's properties in the
list it would have for two revisions of one part too.
Tests: the table (one row per key, the dialog's order); the bill of
materials' keys (rows a component takes, in column order); each scope
on each owner, and refusals that name the owner (the empty key, an
unknown key, a 256-byte key shown cut); the text check at 4096 bytes,
line breaks, tabs and control characters; hostile keys and values
refused without a change; only-part-property changes in each scope,
and changes beside them (units, a component's name, an added, removed
or swapped component); document.metadata.set, remove, undo and redo
evaluate nothing; opening a revision that differs only in its author
solves its joint; the component wording, the shortcuts and the limits;
the dialog's and the window's labels from the table.
What the tests can't reach: every row is Scope::Both, so a known key
refused for its owner (the wrong-owner branch of check) can't happen
yet. It becomes live with the first single-scope row, bom_type, a
component-only key.
Left for later (not this topic):
- Metadata::others() ignores scope, so a component-only key stored on
the design would be neither a dialog field nor listed under other
tools' data. It matters from the first single-scope key (bom_type).
- assembly.bom's rows, its CSV columns and the window's grid headers
still name the three keys by hand; the bill of materials module's
rewrite will read BOM_KEYS.
- The bill of materials types (P1, #5107, into drawings) still use
WELL_KNOWN and the two-argument set: once this is on main, bom_type
is rebuilt on it as one KEYS row with Scope::Component, set through
Owner::Component.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #5681
* sketch: exact circular arcs on drawn 3D wires (#5681)
Add WireArc (centre, unit normal, radius, start/end) as an optional analytic
form on drawn 3D sketch wires, with arc_from_3_points, arc_sweep and
sagitta-bounded arc_polyline; add_drawn_arc_in stores the arc, its three
defining fit points and its samples; move_drawn_point re-derives the arc
atomically and refuses collinear points; validate_wires checks saved arcs.
* engine,ui: sketch.arc3d exact 3D arc command (#5681)
sketch.arc3d draws an exact circular arc through three world points in a 3D
sketch, stored analytically beside its fit points and samples; sketch.move3d
rebuilds it, sketch.inspect reports centre/radius/sweep; placement mapping
(map_wire, now shared with the engine's world state) transforms the arc.
One pending design-format file records the new field. The viewport's 3-Point
Arc tool draws a 3D arc when clicked off the sketch plane, with a live arc
preview; the SKETCH panel offers sketch.arc3d.
* ui,engine: 3D Arc button starts an interactive tool (#5681)
sketch.arc3d now maps to a Draw(3) tool handled by sketch3d: three world clicks (start, end, through - same order as the 2D arc tool) run the command, with the live arc preview and snapping. The command is only enabled while a 3D sketch is open, so the toolbar never offers a tool that could only fail. Locale labels for the command.
* ui: cargo fmt
---------
Co-authored-by: RayGalt <RayGalt@pm.me>
* claim: #3133
* Apply complete feature transactions off the window thread
Evaluate dependent history and prepare reference and GPU display caches before accepting a guarded result. Preserve the evaluated original model for safe editor cancellation and journal only accepted commands.
* fix(ui): preserve original marker across sketch-to-feature edits
* test(ui): verify edit-sketch cleanup and guard Unix link fixture
* test(ui): fix texture disposal and unreachable assertion in feature tests
* fix(build): compile CLI link inspection only on Unix
* Axes and points from circular edges and round faces
In 3D, a round edge or face stands for its circle wherever a command
takes an axis or a point.
Revolve, Surface Revolve, both Circular Pattern dialogs, Plane at Angle
and Move -> Rotate take a circular edge (through its centre, along its
normal) or a cylinder, cone or torus face (its axis). The features keep
the pick as a model reference, so they follow the model when a parameter
moves it. Straight edges work as before; flat faces are refused.
Every 3D point input takes a circle's centre: construction points (which
follow the circle), To Object, patch points, hole placement, and Move's
pivot and points. Hovering shows the axis as a dashed construction line
or the centre as a star, and the dialog's chip names what the pick
stands for ("centre of edge 10", "axis of face 3").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Format the round-pick hover check
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Selection chips: name a round pick as a circle centre or axis
The chip has room for little more than the body and a word or two:
"Shaft · circle centre", "Shaft · circle axis", "Shaft · face 2 axis",
and "Shaft · point" for a point of the model.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Move: a circle's centre in a placed component is where the component shows it
Move's pivot and points read a picked circle from the model in its
component's own frame, while the pick is in the world. They now read it
from the world state (and, editing a Move, from the state before it,
placed the same way), as the viewport and the other round picks do.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Plane at Angle on a planar face about a model edge: test that it follows both
Upstream #1956 made a planar face a base for Plane at Angle; this branch makes a model edge an
axis. The rebase keeps both in one PlaneRef::AtAngle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Expressions: a number and its unit are one value (10 mm / 2 mm is 5)
A unit written after a number was multiplied in at the precedence of `*` and
`/`, so `10 mm / 2 mm` was (10 mm / 2) mm = 5 mm² and `90 deg / 1 rad` a value
in angle², reported as a unit error. The number now takes the unit after it
before `*` and `/` apply; a fraction of numbers before a unit stays one value
(`1/2 in` is half an inch), and an exponent stays a plain number (`2^3 mm`).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Expressions: after a division, a fraction before a unit only when closed up
`width / 10 / 2 mm` read the `10 / 2 mm` as the fraction 5 mm and gave
width / (5 mm) = 8 instead of (width / 10) / 2 mm = 2. After a `/` the
fraction rule now needs the fraction written without spaces (`1 in / 1/2 in`
is still 2); elsewhere `1/2 in` and `10 / 2 mm` are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Patterns: one before the feature it copies follows that feature's parameters (#6726)
A pattern or mirror of features made with the timeline rolled back comes
before its sources and replays them from their definitions. Its
fingerprint chained only the features before it and its own inputs, so a
change of a source's parameter left its result in place: the box grew,
its copy kept the old length, also after rolling forward.
The chain fingerprint of a pattern or mirror of features now also takes
the fingerprint of each feature it replays (and of their sources, for a
pattern of a pattern), wherever they are in the timeline.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Patterns: a test for a later feature taking a deleted source's name (#6726)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Patterns: fingerprint the replayed sources with the document, as fingerprint now takes it (#6726)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #3812
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27
* Sketch Dimension: value box in the design's units (#3812)
A dimension added without a value restated what it measured as
"<value> mm", whatever the design's units. In an inch design the
Dimension tool's value box therefore opened at "25.4 mm" next to a
dimension whose text read 1.000 (inches).
Document::design_length writes a measured length in the design's units
("1 in"), with enough decimals to keep it to the micrometre, so a
dimension that restates the geometry still moves nothing. The Dimension
tool, AutoConstrain's dimensions and Toggle Driven (making a driven
dimension driving) use it. Millimetre designs are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27
* Move the design-units dimension tests into sketch_ux_tests (review)
The #3812 tests go in the existing sketch dimension test file rather than
a new file of their own (AGENTS.md, #3226).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01SBN24y2TcqRcm2zn8Gkj27
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The evaluation cache's 64 MB budget charged every cached feature result the whole model, though a
state shares every body it did not change with the state before it. A design whose model is a few
MB kept only its last few dozen results, so setting a parameter back recomputed what had dropped
out. Each result is now charged for the bodies and sketches it does not share with the state it
started from.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6600
Co-authored-by: Cursor <cursoragent@cursor.com>
* Save an imported mesh that only fits after compression (#6600)
The design file limit was applied to the mesh before Deflate, so a mesh
that had already loaded could not be saved or autosaved.
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix: validate and version large mesh saves (#6600)
---------
Co-authored-by: Colin Faulkingham <colinfaulkingham@Colins-Mac-mini.local>
Co-authored-by: Cursor <cursoragent@cursor.com>
* claim: #6841
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc
* Sheet metal: a pattern of a cut made in the flat is kept like the cut (#6841)
A rectangular, circular or path pattern of an extrude cut through sheet metal was refused
("this sheet machining cannot be preserved in its flat material"), though the cut itself is
kept as a cut-out of the flat pattern. The pattern replayed its copies through the generic
boolean, whose sheet check refuses any change the sheet model can't keep; the cut goes through
the sheet's flat machining first.
Each copy of an untapered extrude cut is now machined into the sheets the same way, in its
moved sketch plane (a moved copy keeps the extrude's prism certificate), and then cut from the
other targets. A copy that meets a folded bend is refused as the cut is there. Mirrored copies
(the sketch plane turns over) and patterns of an intersect (which cut with the union of their
copies) keep the generic path.
Fixes#6841.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6211
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Joints: a loop whose axes are a hair out of parallel still moves (#6211)
Holes picked on parts are rarely exactly in line. A closed loop through
axes a few hundredths of a microradian apart (a lever, link and a rod on
a cylindrical axle) can't close exactly: it closes to nanometres, and the
gap grows as it turns. The loop solver wanted 1e-7 mm, so it threw such a
closure away (the loop stayed open, its parts at 0 dof) or stopped a drive
or drag after a fraction of a degree.
The conflict check is now 1e-4 mm / 1e-6 rad (it was below what its
message can show), and joint.drive / motion and joint.reach close the
loop at each step as at the start: to the tight tolerance where they get
there, otherwise within the conflict check.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #2175
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Body rename: an imported assembly's other bodies keep their names and components (#2175)
An Import keeps its body names by the file's body index, and builds no body for the
file's later instances of a repeated part (`skip`). Renaming a body stored the names by
the body's place in the model instead, so every name after the first skipped instance
landed one slot early (and the new name could land on a skipped slot). The rename looked
right until the design was rebuilt; then those bodies took other names, dropped out of
their components and showed up loose in the import's top component.
`Feature::body_name_slots` maps the bodies a feature builds to their stored slots, and
`Feature::pin_body_names` stores current names through it. The rename, the pinning of
later features' names (rename and suppress) and `Document::body_rename_from` use them.
Fixes#2175
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #1994
* plastic.snap_fit: base_height and new_body options (#1994)
Base Height extends the snap fit's base below the picked face; New Body
makes the snap fit its own body so it can be patterned or moved. Both
optional, serde-defaulted, old designs replay identically.
* ui: snap_fit length-field defaults list gains the optional base height
---------
Co-authored-by: Dahak Builds <dahakbuilds@users.noreply.github.com>
A feature's face points are moved onto their named faces before it is
evaluated, so a To Object extrude follows its target face when an earlier
feature moves it. A pattern's or mirror's copies were built from the
feature as stored, with the face where it was picked: after a gear's disc
was made thicker, the tooth reached the new top but its pattern copies
kept the old height. The copies now use the same moved points; the move
is one helper used in both places.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Test: sketch Intersect keeps its exact cuts, crosses curved faces on the surface, cuts on a top face
Intersect's cut of a box, a cylinder, a sphere and a tilted cylinder, as it is on main, pinned.
Two cases where it is not exact: a plane through a cylinder's rim cuts the mesh's chord (its sides
come out at 6.3159 and 6.3085, not the square root of 40; a hole's walls at 25.0122), and a plane
on a body's top face finds nothing ("projects to nothing on this sketch plane").
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc
* Sketch Intersect: crossings on curved faces lie on the surface; a plane on a top face cuts it
Problem: the plane cut that sketch Intersect makes of a body's mesh (project::section) took a
crossing on an edge where a curved face meets another (a cylinder's rim on its cap) from the
merged normals, which are undefined at the crease, so it fell on the chord: a cylinder's sides came
out 0.01 mm off and uneven. A plane through a vertex or on a face counted the vertices on it as
below, so a plane on a body's top face crossed no edge and found nothing.
Solution: the crossings are found by section_segments, which section fits as before: an edge where
a curved face meets another takes the curved face's normals, so the crossing lies on its surface;
a vertex within 1e-9 x the mesh's size of the plane is on it, on one side for every edge (below
when the mesh lies on or above the plane, else above), and an edge ending there crosses at that
vertex, which is an exact point for the fit. Each segment keeps its B-rep face, for a section that
groups them by face. Cuts that were exact are unchanged.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The component colour tests no longer assume a design always carries a list of
pending format changes; once the release folds them, there is none.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The Joint dialog kept a round edge (a hole's rim), a straight edge and a
corner as plain points where they were picked. When the part got thicker,
a hole moved or the part got longer, the origin stayed where it was and
the jointed part overlapped the other one. An edit that left the picked
spot where it was (lengthening an arm away from the jointed hole) looked
fine, which hid it. Faces and hole walls were already found by name.
The dialog now sends a round edge as its circle's centre with its z, and a
straight edge or corner as an edge pick with its z. The engine keeps them
by name (the round end by its wall and the face across its rim, the edge
and corner by their edge and face names), with the frame the pick showed;
where it can't (no planar face beside the edge, no names), it keeps the
point as before. Edge origins get an optional axis (along the edge, or a
fixed direction) so a hinge on an edge keeps turning about it.
Tests: every joint type and as-built, for each way the dialog picks an
origin, with the arm made thicker, its hole moved and the arm lengthened,
inside one design and through Update Links.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Browser: surface bodies get the surface icon in the Bodies folder (#4165)
Every row in the Bodies folder had the solid body icon, so a surface (an
open shell, such as a Surface Revolve of an open curve) looked like a
solid. A body whose shell does not close now shows the existing surface
icon; solids keep the body icon.
Body::is_surface walks every shell's edges, so ModelBody caches it once per
body (shared by clones, like outline_bounds) instead of the browser
checking it every frame.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Add the surface icon to the requested-icons manifest
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
* feat: add colored components inspection toggle
* feat: persist component colors and add cycling controls
* feat: assign component colors in creation order
* fix: update component color menu integration and translations
* fix: proper description for pending format change.
* fix: deleted duplicated format change description from docs/pending.
* Compare the component colour counter in the features-only check
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Vadim Kalinsky <vadim@kalinsky.com>
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Test: a text's words follow its text parameters, and so does its cut
A sketch text whose words are an expression of text parameters (`Label + '-L'`): a parameter edit
and a configuration row that sets the parameter relabel the text, the text's cut follows, and the
expression is saved with the design.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc
* Text parameters: a sketch text's words built from them follow every change
A design's parameters are numbers; a text's words (a part label, a size code) could only be typed.
Text parameters hold words: `parameters.add` or `parameters.change` with `unit: "text"` (the
expression is the text, quotes optional), and `sketch.text` and `sketch.edit_text` take
`text_expression` (quoted texts and text parameters joined by `+`, `Label + '-L'`) instead of
`text`. The text is laid out anew from its expression on every evaluation, so a parameter edit,
a configuration row or a script relabels it and the features built on it (a cut, an emboss)
follow in the same rebuild. The design file keeps the text parameters and each text's expression
(one pending format change); a configuration table's parameter column can be a text parameter;
the Parameters dialog lists them under the unit `text`.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01PsiqyXWBFGTCX9J51bhysc
* Text parameters: the joints' same-but-features check compares the text parameters
The joints are solved once per change unless the design differs only in its features
(same_but_features, #6372), which names every Document field. The text parameters are a
field of their own and change what a text's words evaluate to, so two designs that differ
in them are not the same but for their features.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #5860
* Doc: stop the names of split faces from growing with every split
* Joints: the long-piece-name test takes the longest name a piece now gets
Split-face names are bounded at 512 bytes since #5860, so the test cannot
build one over 512; it takes the longest the history gives.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: bherbruck <brennen.herbruck@gmail.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>