Commit Graph
78 Commits
Author SHA1 Message Date
jyvikoandClaude Opus 5.5 cf5e0e3c10 Kernel rig: a junction family: oblique wedges 30 to 150 degrees rounded and chamfered (exact), bosses upright and tilted, pipe tees and a Y junction
Four are listed with their causes: the equal-pipe tee (its exact conic-pair rounds meet at the
ellipses' crossings in a corner the old corner code cannot join), the tilted bosses (1001, before the
blend rework too) and the Y junction (refused for room at its triple points).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 11:00:02 -05:00
jyvikoandClaude Opus 5.5 7577e032fb Kernel rig: the turn at a corner of two rounds, Mitre (the default) and Swept, at a pocket's floor and a boss's base, by exact volumes
A round's spandrel A = (1 - pi/4) r^2 and its first moment about its wall M = r^3 (5/6 - pi/4):
Mitre adds L A -+ 2 M per edge (cut at, or run on to, the corners' bisector planes), Swept turns
the section about a convex corner's edge, (pi/2) M a corner, and refuses a concave corner rounded
less than the ball. The pocket's tangent chain round its R3 corners is a torus each. Graded to
1e-7, where Mitre and Swept differ by 6.6e-6. The Swept cases are listed until solid.fillet
takes a turn.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 11:00:02 -05:00
jyvikoandClaude Opus 5.5 539d126489 Kernel rig: four G2 corners wait for the corner step: their patch meets the new section's rounds G1 at one face seam
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 11:00:02 -05:00
jyvikoandClaude Opus 5.5 4df3adc5a7 Curvature fillets: the section's default thumbweight is equal area, so the round's volumes are the circle's
On the round's rails the order-2 section takes off what the ball's circle does: (1 - pi/4) s^2 at a
square corner, first moment 0.0474559669443 s^3 (w = -0.5252123889). The kernel and engine tests
and the curvature rig cases take their volumes from it by their own methods; the pipe on the plate
from its own wedge (70.52878 degrees, w = -0.8544103493). The G2 corner patch's seam test is listed
until the corner step.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 11:00:02 -05:00
jyvikoandClaude Opus 5.5 19455396be Kernel rig: the curvature fillets' expected bodies from the order-2 section at thumbweight 0
SMLIB_BLEND_CURVATURE's section is now the order-2 G^n section at thumbweight 0. Between two
planes square to each other it cuts A = 0.154192655384275 s^2 off the corner, its first moment
about either face 0.0291753295725360 s^3 (Green's theorem on the section): the curvature cases
built on that corner (862, 2708, every-box-edge, every-hole-top-rim, every-l-bracket,
every-block-cylinder-crease, the three-edges-at-bar-corner reports, 3604's fillet) take their
volumes from it by their own methods, the peg's front blend 23.3237146876 (its section along x
up to the wall). Between planes the section's t^3 term vanishes (their feet are linear in the
distance): the box edge case is exactly G3. The boss root is a certified fit, G3 to the plate and
G2 to the wall at Continuity Analysis's tolerances: at least G2. The boss root and the pipe on
the plate pass on SMLib's section and leave the known-failing list.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 11:00:02 -05:00
jyvikoandClaude Opus 5.5 922ee28f37 Kernel rig: the section orders, chord, circle and curvature section, on planes and against a cylinder
Eight fillet cases for the blend's cross-section by its order of contact with the faces, each
graded on its analytic volume at rel 1e-7 and its exact continuity (the order, and not the next):

- a box's top back edge chamfered 3 (G0), rounded r3 (G1) and curvature-rounded 3 (G2): the
  areas cut off the corner s^2/2, (1 - pi/4) s^2 and 113/756 s^2, the last by the default
  thumbweight's definition;
- a pipe R10 dipping into a plate, its concave edge chamfered 2 (the chord between the contacts of
  the ball SMLib rolls for that setback, radius 1), rounded r2 and curvature-rounded 2, each
  section's added area by Green's theorem along the plate, the section and the pipe's arc; the
  order-2 section is built from the faces' feet of the point at distance d from both, which on
  the pipe are not linear in d;
- a boss root curvature-rounded 2, the square corner's section revolved (Pappus);
- a variable round r1 to r5 along a box edge (rel 1e-5): the balls' envelope is a circular cone,
  and the volume is the cone's sections integrated along the edge.

Three fail today and are listed: the two curvature rounds whose faces are not a square corner of
planes (SMLib's quintic blend curve, not the order-2 section: rel 6.5e-7 and 1.2e-5) and the
variable round (great circles, not the envelope's: rel 4.8e-5). The other five pass on SMLib
7ac037e.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 11:00:02 -05:00
jyvikoandClaude Opus 5.5 aa41c0b5de Kernel rig: the fillets known-failing list is the 22 cases that fail on SMLib 7ac037e
Twelve listed cases build on the new blend's end event and exact classes, or were already
built on develop: they come off the list.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 14:33:44 -04:00
jyvikoandClaude Opus 5.5 73416a9bf0 Kernel rig: the exact-class rounds pass on SMLib's classified exact rounds
The rounds now come as the rational surfaces their classes give, closed ones as two faces split
at their seams, the touching pipes' as four: one splines entry a face, each of the class's degrees.
Their KNOWN_FAILING lines go.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 14:33:44 -04:00
jyvikoandClaude Opus 5.5 19014f38a0 Kernel rig: constant rounds of the exact classes, and a tee's round
A plane cutting a cylinder or a cone at an angle, a sphere or a cone coaxial with the other face, a
cone and a cylinder touching one ball, two pipes touching at a point: their rounds' centre lines
are rational, so the rounds are rational surfaces of degrees fixed by the construction ((4, 2),
(2, 2) revolved, (6, 2), (12, 2)). The tee's centre line is not rational; its round is graded on
its volume. Volumes from the divergence theorem over the exact pieces, at rel 1e-6. The six that
SMLib 0cc48bd traces are listed in KNOWN_FAILING with what they come out as.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 14:33:44 -04:00
jyvikoandClaude Opus 5.5 4401ffb1f9 Rig: the test-peg's concave chamfer, alone and after the front chamfer, builds
With SMLib's tangent end as an event of the fillet's trace (blend-end-event 6d73e4f), the
concave chamfer's rail on the cylinder ends where it crosses the seam along which the front
face runs tangent into the cylinder, continued past the vertex, and its end rib on the front
face is built from there. report-peg-concave-chamfer-d2 and
report-peg-front-chamfer-d1-then-concave-chamfer-d2 pass and leave KNOWN_FAILING. The two
chamfers together still fail, now at the mixed-convexity corner where they meet: its line says
so. Rig against SMLib 0cc48bd: no area regresses (963/993 pass, 961 on a87c502), ladder 168/168,
kernel lib only its listed failures.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 14:33:44 -04:00
jyvikoandClaude Opus 5.5 6cd4003adb Rig: the curvature-continuous corner cases pick the curvature fillet
The six corner cases added in 3a854104a took the fillet's default type, on the premise that the
default would become curvature-continuous. The default stays the circular round, so each case
now asks for the curvature fillet itself (type curvature: curvature-continuous sections and
corner patches) and keeps its grading: every seam of the rounds and of the corner patch G2, one
valid body. They are renamed from cov-fillet-g2-default-* to cov-fillet-g2-*.

The oblique three-edge corner (a block drafted 15 deg) and the pocket corner pass. Four fail, as
KNOWN_FAILING now says:

- the corner beside a cylinder: the curvature fillet builds its sections only between planar
  faces;
- the four- and five-edge apex corners: refused because the default setback is shorter than
  where the rounds' contact lines meet (3.90 and 3.51 mm from the apex);
- the mixed corner: SMLib sets back a corner only where its edges are all convex or all
  concave.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 14:33:44 -04:00
jyvikoandClaude Opus 5.5 be0b1b39bd Rig: the test-peg's front chamfer builds
With the SMLib fork's smlib-tangent-ends (a rail's end on its side edge is the rail/edge
crossing), report-peg-front-chamfer-d2 passes. Its line leaves KNOWN_FAILING, for the pin that
carries that fix.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 14:33:44 -04:00
jyvikoandClaude Opus 5.5 a3165f62d2 Rig: fillet corners graded curvature-continuous, the default to be
Six fillet cases that pick their edges with no type, so they take the fillet's default, which the
owner has ruled is to be curvature-continuous (G2) at every corner, with circular rounds kept as
an option. Each grades every seam of the rounds and of the corner patch G2, on one valid body:

- an oblique convex corner (a block drafted 15 deg);
- a four-edge and a five-edge apex corner (pyramids lofted to a point);
- a pocket's concave corner;
- a mixed corner (a step: one concave edge, two convex);
- a corner beside a cylinder (the top corner of a half cylinder).

All six fail on SMLib 2fc375f, listed in KNOWN_FAILING: today's default is the circular round,
whose seams jump in curvature by 1/r. On the five-edge apex the corner patch also meets two
rounds at 8.45 degrees (G0).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 14:33:44 -04:00
jyvikoandClaude Opus 5.5 2273379056 Rig: blends that end where their face runs tangent into another
Fifteen fillet cases on the test-peg's shape with clean numbers: a bar 40 x 16 x 10 whose far
end is a half disc R8, a disc R8 standing 10 on its top, joined, so the front face runs tangent
into the cylinder along x = 40 and the front top edge (convex) meets the concave arc of the top
tangentially there. Each blend ends on a face tangent to the one it rolls on.

- Rounds: both edges together at r2 and r5; one after the other in either order at r2, and at
  r1.5 and r3; the front edge alone as a curvature round, whose end on the cylinder is a
  semicubical cusp. The containment invariant (the unblended body's exact box, to 4e-5) and
  G1 seams, or the analytic volume where the blend has a closed section.
- Chamfers: the front edge alone and the concave arc alone (analytic volumes: the section along
  x up to the wall, the cone's spandrel ring clipped by the sides), both together, and one after
  the other (1 then 2).
- STEP: the peg written to STEP and read back, its front edge rounded (analytic) and both edges
  rounded together.
- A cone: the peg drafted 5 deg, whose front face runs tangent into a cone along a generator,
  its front edge alone and both edges together.

The quadratures are tanh-sinh, converged to 1e-13; SMLib's own volumes of the passing analytic
cases agree to 4e-9. A sphere is left out: a plane meets a sphere tangentially at a point, not
along a seam, so it is not this ending.

On SMLib 2fc375f eight fail, listed in KNOWN_FAILING: every chamfer that ends tangent (status
1001, SmFilletNx1Corner), the two rounds together (the corner patch 0.0374 at r2 and 0.128 at r5
out of the front face, and the rounds meeting with normals 180 degrees apart where their
contact lines on the top cross), the same on the STEP-read peg (status 1001) and on the drafted
peg (its corner refused as unsupported).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 14:33:44 -04:00
jyvikoandClaude Opus 5.5 2c75cf424f Rig: the test-peg corner at r5 and r7
Two more fillet cases, the reported part's concave arc and front top edge rounded together at
r5 and r7, with the same exact-box containment check (graded to 4e-5, the corner patch's
tolerance). On SMLib 2fc375f the corner patch stands 0.128 (r5) and 0.230 (r7) out of the
bar's front face (box y min -0.0699 and -0.1723): listed in KNOWN_FAILING.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 14:33:44 -04:00
jyvikoandClaude Opus 5.5 3c16884f7c Rig: the test-peg's concave arc and front top edge rounded together stay within the body's box
A new fillet case, report-fillet-concave-arc-and-front-top-edge-together-solver-residues:
the reported part's bar (with the sketch solver's residues) whose sides run tangent into the
cylinder, its concave arc and front top edge rounded r2 together. The plane of the front face
bounds the whole body, so every blend lies within the unblended body's exact box (SMLib's tight
box); graded to 4e-5, the corner patch's own tolerance. On SMLib 2fc375f the corner patch
stands 0.0374 out of the front face (box y min 0.0205): listed in KNOWN_FAILING.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 14:33:44 -04:00
jyvikoandClaude Opus 5.5 57edcf61ac Kernel rig: the oblique-cut round keeps its old grade until the new blend algorithm lands
Its seams grade needs the continuity check to skip the body the round is not on. Fillet cases
wait for the new algorithm.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 09:33:29 -04:00
jyvikoandClaude Opus 5.5 6c2a2f3959 Kernel rig: the oblique-cut round graded by its seams (tangent, not curvature-continuous); the flanged rhombus says what it tests (its reliefs stay apart at 60 mm)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 09:33:29 -04:00
jyvikoandClaude Opus 5.5 0bcc24ccd1 Kernel rig: the concave round into the peg's cylinder graded on a volume range (the torus it must add, the band it can't leave)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 09:33:29 -04:00
jyvikoandClaude Opus 5.5 49c7b982ef Kernel rig: the chamfered corner of the lipped shell graded on its volume (the chamfer's triangle through the wall)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 09:33:29 -04:00
jyvikoandClaude Opus 5.5 63dd6ae6f5 Kernel rig: the two 851 chamfers of 2 graded on their volume (the cone's sweep, and its union with the front edge's prism)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 09:33:29 -04:00
jyvikoandClaude Opus 5.5 d184f4f2de Kernel rig: fillets keeps one case per regime; 17 replications of a case in the same regime go
The sloped-basin chamfers and rounds at 0.5 mm rims repeat the 1 mm rim's regimes; two of the
three knife-edge chamfer tips, the r1 and box r3 curvature corners, the r1 tangent corner, the
1 mm pocket-rim and hole-rim chamfers short of the floor and the r1 together-round each repeat a kept case's regime
and grades. #854 moves to 851-chamfer-arc-top-edge-9-5, and the cases that cited a dropped one
cite the kept one or state its formula.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 09:33:29 -04:00
jyvikoandClaude Opus 5.5 1d818a2d1e Fillet rig: five refused blends build, off the known-failing list
926 (the chamfer ending on the boss's wall), the oblique cut's r0.1
round, the every-block r1 round (its seam with the cylinder is no
contact seam, after the blend_seams fix), the up-down squares' concave
chamfers and the shelled box's lip chamfer build with SMLib branch
smlib-blend-refusals (f8650b8 and later). 1207 r0.5 passes SMLib's check
on its rails now and stays listed for the next cause: its end rib on the
boss, which starts where the round and the boss are tangent.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 09:04:03 -04:00
jyvikoandClaude Opus 5.5 f61f25c7f5 Fillet rig: blends past an outer rim of their faces build, on SMLib smlib-blends-past-rims
The owner's ruling: a round or chamfer that runs past an outer edge of its face into open air
builds, tangent where it has room and cut by the face beyond where it runs out. SMLib's branch
smlib-blends-past-rims builds them by the rig's analytic answers. Off the known-failing list:
the disc's rim past its 2 mm wall (190), the hole's top rim R12 past the plate's bottom, the
chamfer past the cylinder's bottom (2893), each closing on the wall continued as itself, and
926's chamfer ending on the boss's wall, which now builds to its answer too.

The sloped basins' R4 rim rounds (1080, mitred rounds built together where one overflows) build
to their analytic volumes (to 6e-9), and stay listed with that reason: their continuity check
(g1 at every blend seam) takes in the mitres' creases, G0 by the mitre ruling.
2893-chamfer-two-distances-elliptical-rim is graded as a solid (the owner: it builds) and stays
listed, waiting on the ruling on unequal chamfers along a rim whose angle varies.
5158-fillet-round-just-past-a-10mm-face stays listed with its cause found: the round passes
5e-6 under the box's top back edge, inside the body's tolerance.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-31 09:04:03 -04:00
jyvikoandClaude Opus 5.5 7953944175 Fillet rig: 1668's R7 past the inside corner is refused at 4 + 2 sqrt2
The round's centre (32 - r, 42 - r) leaves the hollow's corner (30, 40)
outside its circle, opening the wall, where sqrt2 (r - 2) = r: the case
expects the refusal naming 6.828. 2852's R30, refused naming 25.24, now
passes too: both come off the known-failing list.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 22:19:55 -04:00
jyvikoandClaude Opus 5.5 62fe29dbdb Fillet rig: the cases SMLib 737c392 builds come off the known-failing list
The gate on aarch64 Linux reports 16 fillet cases FIXED with the pinned SMLib: the sloped and
equal-slope basin rim chamfers and rounds past their rims (1080-*, 5835-*), the pocket rim
chamfer past the floor, and the three pocket rim rounds now mitred at the pocket's corners
(every-pocket-*). No other area's gate reports a case fixed.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 21:55:53 -04:00
jyvikoandClaude Opus 5.5 20c0c2ffcc Kernel rig: a sloped basin's mitred rim rounds are checked tangent along their contact lines
1080-fillet-sloped-basin-1-mm-rim-r0-5-4-edges asked G1 at every blend seam. Its front wall
leans 19 over 20 and the others 10 over 20, so at each rim corner the two mitred rounds meet the
sloped corner edge at different heights (0.155625 and 0.276393 below the top): the deeper round
runs on past the corner edge and is cut by the plane of the other's wall, a crease by
construction, the gap below the shallower round filled on that plane. The check now measures
the rounds' contact seams, on the top and on each wall, where the rounds are tangent. The
volume is unchanged.

With SMLib smlib-batch-4-mitre (1c15364): the case passes (V 144530.427946 against
144530.427909, 15 faces, sound); before it, only the four corner creases failed the check.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 21:55:53 -04:00
jyvikoandClaude Opus 5.5 9308224ef5 Fillet rig: the knife edge's 0.5 chamfer builds
SMLib's trim took a fillet meeting its face at more than 78 degrees for one with no side
(smlib-batch-4-rulings 971e567); the chord of the knife edge's 0.5 chamfer meets the flat face at
81 degrees. The case comes off the known-failing list.

Needs SMLIB_REV at that SMLib once it is pushed.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 21:55:53 -04:00
jyvikoandClaude Opus 5.5 3772a6e972 kernel, doc: an overflowing round goes first; an edge it removes is gone, and the fillet says so
SMLib (smlib-batch-4-rulings 0e83cca, SMLIB_ABI_VERSION 5) rounds the edges whose rounds overflow
their faces first and then what is left of the others; smlib_blend_dropping says which picks'
edges the overflow removed whole. The smlib crate binds it (Brep::blend_dropping), the kernel
returns those picks (fillet_removing), and a fillet notes them as its warning: "the edge at
(0, 0, 10) was removed by the larger round, so it is not rounded" (a 50 x 50 x 20 block, R21 on
its bottom front edge with the front left upright: the block is R21's alone, in closed form).

Ruling d8: [21, 5, 5] on a 20 cube builds as R21 alone (6107.529370); the test is no longer
ignored. R25 with R2 at a corner (blend_corner) builds the same way, R25's alone in closed form,
where it was refused. The rig's 1080 notched block outline at R8 builds now and comes off the
known-failing list.

Needs SMLIB_REV at that SMLib once it is pushed.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 21:55:53 -04:00
jyvikoandClaude Opus 5.5 6f0bf0dea5 Tests: a 1 degree crease rounds, and the knife edge's chamfers build, on SMLib smlib-batch-4-rulings
With SMLib's smooth limit at half a degree (422e6f1) the 1 degree crease rounds R2 and R20
(the test is no longer ignored), and with a cusp's chamfer the ball of radius d (d231547) the
The 0.5 one stays, for its own cause (the chamfer face left apart from the body). Two corner
cases the same SMLib (replay/1.0.1 and those commits) builds come off too.

Needs SMLIB_REV at that SMLib once it is pushed.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 21:55:53 -04:00
jyvikoandClaude Opus 5.5 c23ef9d93a Fillet rig: the knife-edge chamfers name SMLib's cause, a cusp's ball radius of 0
smlib_chamfer turns the distance into a ball radius d sqrt((1 - c)/(1 + c)), c the faces'
binormals' dot (capi chamfer_radius); at #851's cusp the binormals agree, the radius is 0 and
the call is SM_ERR_INVALID_INPUT before the fillet executive runs (gdb: chamfer_edges sees
radius 0; the dump's why is empty). SolidCraft hands every chamfer to SMLib, so the
ball-contact chord (the ball of radius d: 3.822 wide at d = 2, 159.2365 removed) is SMLib's to
build.

Ruling d4 (2026-10-30).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 21:55:53 -04:00
jyvikoandClaude Opus 5.5 45823002c0 SMLib: pin 68fb916 (tangency-labs/smlib#67)
The owner's bar running tangent into a cylinder rounds its concave arc and
its top edge both together and one after the other in either order, at
r 1 to 7. Two more peg cases come off the fillets known-failing list.

The ladder's shelled dome ring now has 9 edges, not 7: each of its two
cylinder walls is one full-turn face with its seam edge (one wall face per
extruded circle), where it was two halves. Faces, vertices, area and volume
are unchanged.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NvoxKQ2rEZvcXNQnhE3Sgs
2026-10-30 15:19:29 -04:00
jyvikoandClaude Opus 5.5 292ec65c8e Fillet rig: the chamfer running into the openings is named for what it does
fillets/1080-chamfer-runs-into-openings-refused already expects the
9 mm chamfer built and cut by the openings (V = 3350); its id said it is
refused. It becomes 1080-chamfer-runs-into-openings-cut-by-them, and
blend_fit's chamfer_through_the_openings_is_cut_by_them names it so.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 13:52:26 -04:00
jyvikoandClaude Opus 5.5 1878274cb7 Kernel tests, fillet rig: a chamfer past its rim builds, cut by what lies past it
The owner's ruling of 2026-10-30 (d7): a chamfer that reaches or runs
past a rim builds, everywhere, as SMLib's cliff overflow builds a convex
blend: on its faces' continuations, then cut by what the cliff cuts
away. The earlier rule refused a chamfer whose leg runs off its face.
SolidCraft has no such refusal of its own; SMLib refuses these, so the
cases fail on SMLib 985faaee and are listed with its reasons (traced in
gdb at SmFilletErrorInfo::NoteError):

- the sloped basin's single front edge past its rim (1 mm rim 2 and 3,
  0.5 mm rim 4): CloseRemovalRegion, "a cliff overflow's fillet boundary
  lies on the surfaces of two faces": the sheet's boundary along the end
  wall's top edge line from the edge's vertex to the top's contact
  (x = 20, y from -1 to 1, z = 30) lies on the top's plane and the end
  wall's both.
- the equal-slope basin's rim loop 2 and the 5 mm pocket's rim 5.5:
  CloseRemovalRegion, "a cliff overflow's fillet boundary closes on one
  face" (every edge of the loop blended).
- the sloped basin's front and right edges 2: status 1001,
  SmFilletNx2Corner, CalcFilletIntSideFace.
- the cylinder's rim 2 across the top and 25 down its 20 mm wall: status
  1001, SmFilletNx1ClosedCorner cannot compute its geometry.

Expectations, each from a closed form or an exact quadrature:

- chamfer_wider_than_sloped_basin_rim_is_refused becomes
  chamfer_wider_than_sloped_basin_rim_builds, ignored until SMLib builds
  it: the triangle clipped to y >= 0, times 30 + z (shoelace):
  73.450475, 142.112912, 184.526613; the rig's 1080-chamfer-sloped-
  basin-*-past-the-rim cases: V = 144459.882858, 144391.220421,
  144082.140054.
- blend_corner's a_rim_loop_chamfer_running_off_its_rim_is_refused
  becomes ..._builds, ignored likewise: sliced at depth t the mitred loop
  takes the pocket's rectangle grown by w(t) = d (1 - t / delta) on each
  side, clipped to y >= 0, less the rectangle, Simpson exact on each
  quadratic piece: 375.673069, V = 139957.660264 (the rig's
  1080-chamfer-equal-slope-basin-1-mm-rim-loop-2 too).
- 5835-chamfer-sloped-basin-1-mm-rim-2-two-edges: the same slicing with
  the front and right sides grown, 161.279149, V = 144372.054184.
- every-chamfer-pocket-rim-5-5-past-the-floor: 50 d^2 + (4/3) d^3 at
  5.5, the groove 0.5 deep round the floor included, V = 19265.666667,
  15 faces.
- 2893-chamfer-two-distances-past-the-bottom: the frustum r 8 to 9.6
  over 20, pi 20 (64 + 76.8 + 92.16) / 3 = 4879.102831, 3 faces.

Each drops "-refused" from its id (the 5.5 pocket's says past the floor).
The same slicing reproduces the existing 5835-...-4-mm-rim-2-2-edges
(176.006388), equal-slope loop 0.5 (24.455545) and half-width
(5.426545) values.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 13:52:26 -04:00
jyvikoandClaude Opus 5.5 3a2fac31a1 Kernel tests, fillet rig: a chamfer as wide as its rim builds
The owner's ruling of 2026-10-30 (d7): a chamfer that reaches or runs
past a rim builds, everywhere. The earlier rule refused a full-width
chamfer, naming the largest size that fits. SolidCraft has no such
refusal of its own (a blend's TooLarge is SMLib's SMLIB_ERR_NO_ROOM,
and the doc layer only names the largest fit), and SMLib already builds
these, so only the expectations change, each from a closed form or an
exact quadrature:

- chamfer_wider_than_sloped_basin_rim_is_refused's full widths become
  chamfer_as_wide_as_sloped_basin_rim_builds: the whole triangle,
  d drop / 2 (60 - drop / 3), drop = 20 d / sqrt((20 - margin)^2 + 400)
  (shoelace over the section, its length 30 + z between the sloped end
  walls): 21.662379 (1 on 1 mm), 5.359321 (0.5 on 0.5 mm). The basin and
  the removal move into sloped_basin and sloped_basin_rim_chamfer_removed.
- fillets/1080-chamfer-sloped-basin-{1,0-5}-mm-rim-as-wide-as-the-rim:
  V = 144511.670954, 144261.307346.
- fillets/every-chamfer-pocket-rim-5-full-depth: 50 d^2 + (4/3) d^3 at
  d = 5, V = 19583.333333, 11 faces (the walls used up).
- fillets/every-hole-top-rim-chamfer-10-full-depth: the triangle 10^2/2
  revolved at rho = 5 + 10/3 (Pappus), V = 16000 - 3250 pi / 3 =
  12596.607959, 7 faces.
- fillets/1113-chamfer-arc-top-edge-full-wall-height: the 9.5 case's
  Int rho asin(21/rho) h(rho) drho at s = 10, by Gauss-Legendre in
  u = asin(21/rho), 1303.400331, V = 8287.993768.

Each drops "-refused" from its id and its KNOWN_FAILING line goes: all
five pass on SMLib 985faaee.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 13:52:26 -04:00
jyvikoandClaude Opus 5.5 7fe880a7bf SMLib: pin f8fd83e (tangency-labs/smlib#66)
The batch brings history Kept for a face only cut by a vertex, revolve of a
curve touching its axis, loops touching at a vertex, a torus rail on its axis,
and the fillet causes behind the owner's bar running into a cylinder: a
tangent edge past a tangent side edge is the corner's edge, the rails of a
round collapsing at its end end at one point, and a trace from a tangent point
starts along the curve.

The two peg cases with the sketch's solver residues come off the fillets
known-failing list: both build.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NvoxKQ2rEZvcXNQnhE3Sgs
2026-10-30 12:14:18 -04:00
jyvikoandClaude Opus 5.5 9b35727976 Fillet rig: the known-failing list names the report- cases, not their old ids
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 08:02:50 -04:00
jyvikoandClaude Opus 5.5 6cc7597502 SMLib import: an extruded circle is a cylinder over the face's trimmed range
This replaces the spline fallback of 64efbe7f6. A face SMLib holds as a rational spline that is
an extruded circle was recognised as a cylinder over the spline's whole parameter range: for the
upper half of the peg's wall after the front top round that range runs 393 degrees round (u in
[-15, 40.18], SMLib's support surface extended past the face), and SMLib refuses a cylinder past
one turn. The face itself, its loops' box, spans u in [0, 8 pi]: half a turn. The cylinder now
takes the face's trimmed range, the least and greatest u and v of its uses' pcurves over their
edges' intervals, found to rounding on each Bezier span (the values at the pieces' ends bound the
extreme from below, the control points from above; pieces that cannot beat the best are dropped,
the others halved). A face whose trims run more than one turn round is no face of a cylinder: it
is refused as an invalid record, never kept as a spline.

The peg (40 x 16 x 10 bar, R8 end, a disc R8 extruded 10 up on its top, joined), front top edge
rounded r2: the body measures to 1e-7 of its closed form, the three r2 corner rounds after it
build and measure, and the upper wall comes back from SMLib a cylinder of radius 8 (engine test).

The rig case of the round of the edge where that round meets the wall (tangent at one end) still
fails, for another reason: on the wall as its exact cylinder SMLib refuses the round as larger
than the faces beside its edges allow (it fades to nothing at the tangent end) instead of
returning a body its own check refuses. Its KNOWN_FAILING line says so.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 08:02:50 -04:00
jyvikoandClaude Opus 5.5 ccc690c535 Fillets: a curvature-continuous fillet's corners are G2 patches
A curvature-continuous fillet (type curvature, equivalent radius 2) of the three edges at a top
corner of the owner's bar built, but its corner was SMLib's own patch, which is only tangent to
the rounds: Continuity Analysis measures a 35.8 / mm curvature jump across its seams (with the
rounds G2 to the faces everywhere else), and it shows as a dome sitting on the corner, the
vertical round's shading lost under it. All three edges were rounded; the corner was not
curvature-continuous, and nothing said so.

Such a corner, where three or more rounded edges meet, is now set back (1.5 r unless a setback
names it) and left open by SMLib with the curvature sections (smlib_blend_setback_open with
SMLIB_BLEND_CURVATURE), and filled with the G2 patch fillet_g2_corners already uses for circular
rounds (fillet_g2_with_g2_corners). The `corner` option no longer leaves a curvature fillet with
SMLib's patch: its corners are always G2, and setbacks on it set back the curvature rounds (they
were circular rounds before). Where SMLib or the patch cannot build it, it is refused.

On the reported geometry every seam of the rounds and the patch is G2 (rig
report-fillet-curvature-three-edges-at-bar-corner-solver-residues), and the rounds outside the
setback cube measure exactly: V0 - 27 - (the quintic section, A2 = 0.597884, along the front edge
from 3 to the wall and along 7 and 13) = 9541.116961 (...-outside-setback). With round coordinates
SMLib's open sheet fails its own check (a 2D curve cusp, SmBSplineCurve test 13): the fillet is
refused, listed as known failing (report-fillet-curvature-three-edges-at-bar-corner).

Test: corner_g2_tests::curvature_rounds_meet_at_a_g2_corner (box corner, r5: the patch's jump
under CURVATURE_SHARE / r clear of the hole's corners, SMLib's own patch over ten times that).

Changes a default: a saved curvature fillet with such a corner rebuilds with the G2 patch; there
is no preference or fallback to SMLib's patch.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 08:02:50 -04:00
jyvikoandClaude Opus 5.5 a9755bdd23 Fillet rig: the owner's reports are report- cases; the G2 corner graded at its seams
The cases from the owner's reports in the app (no issue) were named and cited after issues they
only resemble (#9, #896, #1207). They are report-<name> now and list no sources; their `what`
says where they were reported. The README gives the convention (report- for a report with no
issue or pull request, cov- for a command with no source).

report-fillet-g2-corner-of-bar-running-into-cylinder was graded by a 3^3 volume band and a face
count, which say little about a G2 corner. It keeps the band (provable: the patch differs from the
rolling ball only within the setback cube) and adds the corner seams' curvature jump, as
fillets/9-fillet-corner-r1-curvature-default-setback scaled by r = 2 (at most 0.0025 / mm, clear
of the hole's corners by 0.48 mm, within 4.4 mm of the corner). A new
...-outside-setback case cuts the setback cube [-1, 3] x [-1, 3] x [7, 11] away and grades the
three rounds outside it exactly: V0 - 27 - (front spandrel from x = 3 to the wall + (1 - pi/4) r^2
over 7 and 13) = 9342.029541. The bare face counts are dropped.

The -solver-residues recipes now take the reported sketch's points exactly (the arc's end
x = 41.649711830726524); they fail as before.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 08:02:50 -04:00
jyvikoandClaude Opus 5.5 de9c005f2b Blends: a blend face is named by its picked edge, not an edge it took up
A 220 x 11 two-distance chamfer of a tapered plate's bottom front edge (rig fillets/5181) runs up
the front face past its straight side edges, l2|start and l6|start, and takes them up: no result
edge comes from them. SMLib leaves the blend face untagged, and it was given every blended edge
whose two faces lie next to it: the picked edge l1|start and both taken-up side edges. Its name
came from the first in edge order, F3:blend:F2:side:l6|F2:start, an edge the user never picked.
A blend face now comes from the picked edges it lies between; only a face that lies between no
picked edge's faces (a corner's piece over a short edge the corner took up) comes from the
taken-up edges it lies between. The chamfer is F3:blend:F2:side:l1|F2:start everywhere on it.

Persistent names: a blend face that also lay between the faces of an edge the blend ran over is
now named by its picked edge only. There is no alias for the old name (5181's
F3:blend:F2:side:l6|F2:start): a saved reference to it is reported lost.

Also corrects 5181's "what": the chamfer builds (335399.749), it is not refused.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 08:02:50 -04:00
jyvikoandClaude Opus 5.5 1e6c91a108 Fillet rig: the concave arc where a bar's top meets a cylinder its sides run tangent into
An r2 round of the arc adds the spandrel ring clipped by the bar's sides, integral over rho in
[8, 10] of [2 - sqrt(4 - (10 - rho)^2)] rho 2 asin(8 / rho) = 18.455363. With round coordinates
it builds to that; with the reported design's sketch residues (~1e-10 mm) SMLib's blend fails,
status 1001 (SmFilletNx1Corner: unable to make topology at the arc's end), listed as known
failing.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 08:02:50 -04:00
jyvikoandClaude Opus 5.5 c9bf97ce49 Blends: an edge is smooth only where its faces are tangent all along it
The edge where a round runs into a cylinder's wall it is tangent to at one end (the bar's front
top round meeting the wall at (40, 0, 8), where the round's contact with the front face meets the
wall's tangent line with it) was refused as smooth, "nothing to round": the faces' normals were
compared at the edge's start alone, which was that tangent end. They are now compared at five
stations from end to end, and an edge is smooth only where its faces meet tangentially at every
one: this edge is a crease everywhere but its end. The wall's seam with the front face, tangent
all along, is still refused as smooth.

The round of that edge with its tangent chain (the top's concave arc) now reaches SMLib, whose
result fails its own check (internal poles, coincident control points, cusps where the round
fades out): its rig case in fillets is listed as known failing for that SMLib defect.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 08:02:50 -04:00
jyvikoandClaude Opus 5.5 977949819e SMLib import: an extruded circle past a turn stays its exact spline
A round of a bar's top edge, where the bar's side runs tangent into a cylinder standing on its
round end, seemed to build: SMLib's result holds the cylinder's wall as a rational spline whose
parameter range runs 393° round (u in [-15, 40.18]). Going back into SMLib (to measure the body
or change it again) the record's extruded circles become SMLib cylinders with the face's range on
them, and that range was 6.866 rad: SMLib refuses a cylinder past one turn
(SM_ERR_INVALID_INPUT from BrepFromFlat's face range check). The body could not be measured, a
second round on it failed, and the app said one of its freeform faces can't be used. An extruded
circle whose range runs more than one turn round now stays the exact spline it is.

The bar of the reported design (40 x 16 x 10 with a R8 end, a disc R8 sketched on its top and
extruded 10 up, joined): the front top round removes the spandrel up to the cylinder's wall,
integral over y in [0, 2] of (2 - sqrt(4 - (2 - y)^2)) (40 - sqrt(64 - (8 - y)^2)) = 32.306475;
the three rounds at the other top corner after it remove 53.285832 in all (spandrels outside the
corner cube, the cube less the rolling ball's eighth). Both now build and measure to 1e-7; the
curvature corner of the three edges at once (setback 3) builds too.

Rig cases (fillets) for the three reports: the curvature corner of the three edges, the front
top round, and the three corner rounds after it pass; the same corner rounds with the design's
~1e-10 mm sketch residues fail in SMLib (its corner's surface of revolution is close to singular
at its boundary) and are listed as known failing. (Their ids take the report- convention in the
rig commit later on this branch.)

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 08:02:50 -04:00
jyvikoandClaude Opus 5.5 bf85e0a6cf Fillet rig: the knife edge's R2 round builds on the new SMLib pin
fillets/851-fillet-knife-edge-tip-r2 passes on develop's SMLib (985faae): its line
leaves KNOWN_FAILING. The chamfers of the same edge still fail.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:37:21 -04:00
jyvikoandClaude Opus 5.5 30dce7fbaf Fillet rig: the sloped basin's rim loops with their mitred corners' exact volumes
The owner ruled on 2026-10-30 that rounds meeting at a concave corner beside an
unpicked sharp edge are mitred, which fixes the basin loops' re-entrant corners.
Each loop case now grades its exact volume (rel 1e-6): each blend takes
Int width(z) length(z) dz, its section's width from its wall to its arc or chamfer
line (the front one clipped at the slab's face where it runs past the rim), its
length between its neighbours' walls extended; each corner of two picked edges adds
the overlap of their section prisms in the quadrant beyond both walls,
Int width_1(z) width_2(z) dz (r^3 (5/3 - pi/2) for vertical walls, as
every-pocket-rim-edges-r2). One edge alone reproduces the single-edge closed forms to
3e-7 of the removal. The equal-slope chamfer loop 0.5 passes; the others stay on
KNOWN_FAILING with the causes they had (SMLib status 1001, the surface-of-revolution
check, rounds past the rim not built by subtraction).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:37:21 -04:00
jyvikoandClaude Opus 5.5 ecbca1f747 Fillet rig: grade the 851 rows' rounds G1 at their own tangent seams
The 851 table rows grade continuity again, on each round's seams to the faces it
rolls on, picked by points at the middle of its edge (the top front round's at
z = 8 on the front and y = -19 on the top, the arc's at rho 23 and rho 21, the
uprights' at their contacts). The default `blend` selection read G0 there because
it pairs a blend face with the contact faces of every edge in the feature, so where
a round ends square on another edge's contact face (a crease by construction) it was
graded as a tangent seam: a gap in the grader's seam selection, worked around here
by naming the seams. All seven rows pass.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:37:21 -04:00
jyvikoandClaude Opus 5.5 191fa98395 Fillet rig: the R7 round past a thin wall's inside corner held to its exact volume
fillets/1668-fillet-outer-top-edge-of-thin-wall-r7-past-inside-corner (and the
both-sides R7 case) now grade the volume at rel 1e-6 (0.04 mm^3), not the rig's
1e-3. The closed form is exact: V0 = 104 64 42 - 100 60 40 less the round's
section (1-pi/4) 49 along 104 plus its part over the hollow, the square
[25,30] x [35,40] outside the circle about (25,35), Int_sqrt24^5 (5 - sqrt(49-u^2)) du
= 0.0050679 mm^2 (a 0.0005 grid gives the same to 1e-9), along 100: 38458.896.
SMLib gives 38458.389, 0.507 mm^3 less: exactly that part over the hollow, which is
not material, taken anyway where the round opens its slit. The unit test's bound
was right; the case goes on KNOWN_FAILING with that cause. The both-sides case
passes at the tighter tolerance.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:37:21 -04:00
jyvikoandClaude Opus 5.5 ebd1b15098 Fillet rig: the geometry of the failing fillet and chamfer unit tests, as cases
The fillet and chamfer unit tests that checked geometry become fillets rig cases,
built through commands with answers derived by hand (each method field gives the
derivation): a plate outline and a disc rim as tall as or past their wall, a
notched block's outline at R7 and R8, a cube corner as wide as its faces (refused,
and reduced), the 1668 wall at R7 alone and both sides, the 2852 U shell at R30
(refused, naming 25.24), the 851 knife edge (R2, chamfers 0.5/2/5 on three
constructions), the arc top edge at the full wall height and at 9.5, the 851
table of selections, the 556 top edge ending on the boss wall, the 2893
cylinder-rim chamfer refusals and the elliptical rim, seed 33's full round, the
sloped basin rim blends (single edges with exact volumes, loops with the slab's
box), and three action-matrix chamfers and fillets. fillets/851's three-edge
corner gets its volume (67.051 removed, re-derived on a grid; the engine test had
67.05). Chamfers whose leg runs off the face beside the edge are refused and rounds
past a face on its tangent side build, as the owner ruled on 2026-10-30. The cases
that fail today are on KNOWN_FAILING with their cause.

The unit tests are removed, except two cut to what no command can express: the
per-edge-radius refusal at a cube corner and the chamfer of a cylinder's seam.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:37:21 -04:00
jyvikoandClaude Opus 5.5 e9963439b1 Kernel tests: the round into a hole moves to the rig, with the hole cut the test's way
a_round_into_a_hole_is_cut_by_it (issue_324_tests.rs) built rig case
fillets/324-fillet-over-hole-overlap's body, but cut its hole with a cylinder
longer than the block (z -1 to 11) where the rig extrudes a sketch circle
flush. The new case fillets/324-fillet-over-hole-cut-by-overlong-cylinder
builds it that way (solid.cylinder, base z -1, height 12, cut) and holds it to
the same hand-derived answer: block 40x20x10 less the r3 hole at (20, 14.5)
(282.74) less the R4 round on the top edge at y = 20, 40 (16 - 4 pi) = 137.35,
plus what both remove, the integral over y in [16, 17.5] of
(4 - sqrt(16 - (y - 16)^2)) * 2 sqrt(9 - (y - 14.5)^2) = 0.375830 (re-derived
with the substitution y = 17.5 - s^2, 200000 steps):
V = 8000 - 90 pi - 40 (16 - 4 pi) + 0.375830 = 7580.287315, and G1 on the
blend. It passes today (aarch64, SMLib), as the flush case does, so it needs no
KNOWN_FAILING line; the unit test, a duplicate of the two cases, is dropped.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-30 07:12:24 -04:00