* Kernel: the B-rep record and the native body file come from solidcore-record
SolidCraft's portable B-rep record (`solidcraft_geom::brep`: brep.rs, topology, history,
envelope, part, curve2) and the native body file (`solidcraft_kernel::native`: the tagged binary
codec and the container) move to solidcore's `solidcore-record` crate: geometry as data, with
structural validation and no maths (solidcore's docs/layers.md, stage 1). Every caller uses
`solidcore_record::brep` and `solidcore_record::native`; the old copies are deleted.
What computes from coordinates stays with the kernel, in geom's `brep`:
- `brep::check`: the record's geometric checks (orthonormal frames, non-degenerate planes,
unit revolution axes, non-singular placements). `check::validate` and
`check::validate_built` are the record's validation and these together, and every caller of
`Brep::validate` uses them, so what is accepted is unchanged;
- `brep::label`: a surface's natural ranges (a cone's apex), `curve_interval`,
`edge_curve_interval` and `form_turns`;
- `brep::pcurve::eval`: a pcurve's point;
- `geometry::check`, `placement::moved` and `split_edges` become functions on the record.
The kernel's native module keeps the conversion between a body and its saved record
(metadata.rs) and checks the decoded record's geometry. `native/analytic.rs`, which no module
declared, is deleted.
solidcore-record is pinned to its rev on solidcore's `layer-record` branch.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NvoxKMbMFSQU8tzRtoJhtT
* Geometry: Vec2, Vec3, Plane and the profile types come from solidcore-record
The plain data of vectors and points, sketch planes and planar profiles (`Seg2`, `Loop2`,
`Region2`) moves to `solidcore-record`, with its constants and component-wise operators only
(owner decision, solidcore layer split). Their geometry stays in geom as traits:
`Vec2Geom`, `Vec3Geom`, `PlaneGeom`, `Seg2Geom`, `Loop2Geom`, `Region2Geom`, `Seg2ArcFit`,
`Loop2ArcFit` and `Region2ArcFit`, in scope with `use solidcraft_geom::prelude::*`. Every caller
names the types from `solidcore_record`; geom no longer defines or re-exports them.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NvoxKMbMFSQU8tzRtoJhtT
* Kernel: pin solidcore-record to solidcore main f5e8e9a29
solidcore-record is merged on solidcore main (tangency-labs/solidcore#2519); its crate there is
identical to the rev pinned before but for its clippy configuration. The lock is regenerated
against the merged rev.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NvoxKMbMFSQU8tzRtoJhtT
---------
Co-authored-by: jyviko <2501648+jyviko@users.noreply.github.com>
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* Sketch: a dog bone's outline outside it meets outside both notches (#10984)
Where two tangent arcs touch at a cusp, the copies of the two arcs cross
twice, both crossings as far from the cusp, and rounding chose one: on
one side of a dog bone the outline ran both copies on and drew a loop
into the bone. Such a tie now takes the crossing that cuts both copies
short.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Dog bone test: the outline goes outside, away from the picked bottom line
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
The offset sets an offset circle's radius from its source after the solve,
but the solve still counted that radius as a free unknown, so a
dimensioned circle and its offset reported 1 DOF instead of 0. Lines and
arcs were not affected: the offset already holds their end points. The
solve now holds an offset circle's radius too.
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #6569
* Sketch: an offset slot can still be moved by the dimension that places it (#6569)
An offset arc is drawn round its source's own centre, and its ends are
held while the sketch solves (the offset is rebuilt from its source
afterwards). Its arc condition, both ends as far from the centre, then
only tied that shared centre, and the source arc with it, to the middle
of the held ends: a slot offset by 1 mm lost a degree of freedom, and
the length that places it was refused as conflicting.
The solver and the constructive reading now leave out the arc condition
of an offset arc round its source's centre (Sketch::offset_arc_follows_source),
as #4466 did for the Parallel between an offset line and its source. The
source's own arc keeps the centre; nothing changes without an offset.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
* Sketch: a test for a rounded rectangle with an offset round it (#6569)
kaievns's case from the review: the offset's corner arcs tied each corner
centre to a 45 degree line, so the height followed the width and every
width change was refused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
* claim: #4464
* Sketch offset keeps its source lines free to turn (#4464)
An offset adds a Parallel between each source line and its offset line.
Since offsets became associative, the offset's points are held during a
solve, so each Parallel pinned its source line to the offset line's
current direction: a closed chain lost its turning freedom (8 degrees of
freedom became 6), and Horizontal or an angle edit on a source line was
refused as conflicting.
The solver and the constructive reading now leave out a Parallel that
ties an offset line to the source it follows while the association lives;
the association already keeps them parallel. After Break the stored
Parallel drives again.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 5.5 <noreply@anthropic.com>
Sketch Mirror, rectangular and circular Pattern, and Offset now show a green live preview that follows the selection and settings; OK commits, Cancel leaves the sketch unchanged. The shared dialogs show the current selection step and source counts, sources can be toggled with Ctrl/Cmd-click, cleared and reselected.
Offsets keep editable driving distance dimensions (One Side, Two Sides, Symmetric) that update the derived curves without moving the source, with undo/redo and save/reopen. Format 19: older files keep their fixed offsets.
New dialog labels in en, zh, ja, de and ko.
Fixes#696. Fixes#517.