diff --git a/tests/kernel-cases/fillets/1207-fillet-bar-top-edge-after-boss-arc-round-no-tangent-chain/expected.json b/tests/kernel-cases/fillets/1207-fillet-bar-top-edge-after-boss-arc-round-partial-chain/expected.json similarity index 100% rename from tests/kernel-cases/fillets/1207-fillet-bar-top-edge-after-boss-arc-round-no-tangent-chain/expected.json rename to tests/kernel-cases/fillets/1207-fillet-bar-top-edge-after-boss-arc-round-partial-chain/expected.json diff --git a/tests/kernel-cases/fillets/1207-fillet-bar-top-edge-after-boss-arc-round-no-tangent-chain/recipe.json b/tests/kernel-cases/fillets/1207-fillet-bar-top-edge-after-boss-arc-round-partial-chain/recipe.json similarity index 100% rename from tests/kernel-cases/fillets/1207-fillet-bar-top-edge-after-boss-arc-round-no-tangent-chain/recipe.json rename to tests/kernel-cases/fillets/1207-fillet-bar-top-edge-after-boss-arc-round-partial-chain/recipe.json diff --git a/tests/kernel-cases/fillets/1207-fillet-box-end-edge-into-unblended-round-partial-chain/expected.json b/tests/kernel-cases/fillets/1207-fillet-box-end-edge-into-unblended-round-partial-chain/expected.json new file mode 100644 index 000000000..c7c237e6f --- /dev/null +++ b/tests/kernel-cases/fillets/1207-fillet-box-end-edge-into-unblended-round-partial-chain/expected.json @@ -0,0 +1,14 @@ +{ + "sources": [ + "tangency-labs/solidcraft#1207" + ], + "what": "an edge that runs on tangentially into a round left out of the blend (tangent chain off) is rounded on past the round's end arc until it leaves the material", + "source": "analytic", + "method": "cube 20 (V0 = 8000), its top back edge (y=20, z=20) rounded r3: removes 20 (9 - 9 pi/4) = 38.628316. The end face's top edge (x=0, z=20, y 0..17) then rounded r1 alone, tangent_chain false: over y 0..17 it removes 17 (1 - pi/4) = 3.648231; at y=17 the edge goes on tangentially into the r3 round's end arc, and the r1 round's cylinder (axis x=1, z=19) runs on along y through the r3 round, cutting the part of its section under the round's surface z = 17 + sqrt(9 - (y-17)^2) until that surface drops below z=19 at y = 17 + sqrt(5): with t = sqrt(9 - (y-17)^2) - 2, the section's area under it is t - (t sqrt(1-t^2) + asin t)/2, integrated over y 17..17+sqrt(5) (Simpson, 200000 steps) = 0.218236. V = 8000 - 38.628316 - 3.648231 - 0.218236 = 7957.505202", + "outcome": "solid", + "body_count": 1, + "volume_mm3": 7957.505202, + "continuity": { + "order": "g1" + } +} diff --git a/tests/kernel-cases/fillets/1207-fillet-box-end-edge-into-unblended-round-partial-chain/recipe.json b/tests/kernel-cases/fillets/1207-fillet-box-end-edge-into-unblended-round-partial-chain/recipe.json new file mode 100644 index 000000000..12a589ebb --- /dev/null +++ b/tests/kernel-cases/fillets/1207-fillet-box-end-edge-into-unblended-round-partial-chain/recipe.json @@ -0,0 +1,40 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 20, + "width": 20, + "height": 20, + "body_name": "Cube" + } + }, + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 10, + 20, + 20 + ] + ], + "radius": 3 + } + }, + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 0, + 8, + 20 + ] + ], + "radius": 1, + "tangent_chain": false + } + } + ] +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/1207-fillet-box-end-edge-into-unblended-round/expected.json b/tests/kernel-cases/fillets/1207-fillet-box-end-edge-into-unblended-round/expected.json index c7c237e6f..6e90635c7 100644 --- a/tests/kernel-cases/fillets/1207-fillet-box-end-edge-into-unblended-round/expected.json +++ b/tests/kernel-cases/fillets/1207-fillet-box-end-edge-into-unblended-round/expected.json @@ -2,13 +2,14 @@ "sources": [ "tangency-labs/solidcraft#1207" ], - "what": "an edge that runs on tangentially into a round left out of the blend (tangent chain off) is rounded on past the round's end arc until it leaves the material", + "what": "an edge that runs on tangentially into a round's end arc, its tangent chain rounded with it: the r1 round follows the end face's outline over the r3 round and down the back edge", "source": "analytic", - "method": "cube 20 (V0 = 8000), its top back edge (y=20, z=20) rounded r3: removes 20 (9 - 9 pi/4) = 38.628316. The end face's top edge (x=0, z=20, y 0..17) then rounded r1 alone, tangent_chain false: over y 0..17 it removes 17 (1 - pi/4) = 3.648231; at y=17 the edge goes on tangentially into the r3 round's end arc, and the r1 round's cylinder (axis x=1, z=19) runs on along y through the r3 round, cutting the part of its section under the round's surface z = 17 + sqrt(9 - (y-17)^2) until that surface drops below z=19 at y = 17 + sqrt(5): with t = sqrt(9 - (y-17)^2) - 2, the section's area under it is t - (t sqrt(1-t^2) + asin t)/2, integrated over y 17..17+sqrt(5) (Simpson, 200000 steps) = 0.218236. V = 8000 - 38.628316 - 3.648231 - 0.218236 = 7957.505202", + "method": "cube 20 (V0 = 8000), its top back edge (y=20, z=20) rounded r3: removes 20 (9 - 9 pi/4) = 38.628331. The end face's top edge (x=0, z=20, y 0..17) then rounded r1 with its tangent chain: at y = 17 it runs on tangentially into the r3 round's end arc on x = 0 (convex, a quarter circle about y = z = 17), which runs on at (0, 20, 17) into the back upright (x=0, y=20, z 0..17), so the chain is those three edges; it ends at the front face y = 0 and the bottom z = 0, each square to its edge, so each straight round ends in a plane section. With A = 1 - pi/4 the r1 spandrel and c = r (10 - 3 pi)/(3 (4 - pi)) = 0.223368 its centroid's distance from either face: the top edge and the upright remove 17 A each; along the arc the spandrel, in the half plane through the r3 axis, lies at radius 3 - u from the axis (u its distance from the round's surface), and is turned through the arc's quarter turn: (pi/2) A (3 - c) = 0.935991 (Pappus). V = 8000 - 38.628331 - 34 A - 0.935991 = 7953.139216. Faces: the cube's 6, the r3 round, and the r1 chain's three (cylinder, torus, cylinder): 10.", "outcome": "solid", "body_count": 1, - "volume_mm3": 7957.505202, + "volume_mm3": 7953.139216025938, "continuity": { "order": "g1" - } + }, + "faces": 10 } diff --git a/tests/kernel-cases/fillets/851-fillet-top-front-then-front-left-upright/expected.json b/tests/kernel-cases/fillets/851-fillet-top-front-then-front-left-upright/expected.json index f47364e63..592633039 100644 --- a/tests/kernel-cases/fillets/851-fillet-top-front-then-front-left-upright/expected.json +++ b/tests/kernel-cases/fillets/851-fillet-top-front-then-front-left-upright/expected.json @@ -3,9 +3,9 @@ "tangency-labs/solidcraft#851", "tangency-labs/solidcraft#854" ], - "what": "on #851's knife-edge part (tessellation/1263): the top front edge R2, then the front-left upright R2 as a fillet of its own, ending in the first round", - "source": "invariants", - "method": "the rolling ball of R2 fits on every one of these edges and where they meet; the corner between rounds that end in each other has no closed form here: one closed valid solid whose display mesh closes. Each round meets the faces it rolls on G1: graded at its seams' middles (the top front round's at z = 8 on the front and y = -19 on the top; the arc's at rho 23 on the top and rho 21, z = 8 on the wall; the uprights' at their contacts, z = 5). Where a round ends on a face or on another round the seam is a crease by construction and is not graded.", + "what": "on #851's knife-edge part (tessellation/1263): the top front edge R2, then the front-left upright R2 with its tangent chain: up the first round's end arc and along the left top edge", + "source": "analytic", + "method": "plate x 0..41.1667, y -21..0 and the corner x 41.1667..62.1667 less the cylinder r 21 about (62.1667, -21), 10 high (tessellation/1263): V0 = 10 (62.1667 x 21 - pi 21^2/4) = 9591.394099. The top front edge rounded R2 first: no ball of R2 inside the part (centre y >= -19, z <= 8) reaches its spandrel (y in [-21,-19], z in [8,10], outside the circle about (-19, 8)), so it removes the spandrel's material, from x = 0 to the wall x_w(y) = 62.1667 - sqrt(441 - (y+21)^2): Int over the spandrel of x_w(y) = 35.344727 (Simpson in y = -19 - 2 sin t, 200000 steps). Then the front-left upright (x=0, y=-21, z 0..8) with its tangent chain: at z = 8 it runs on tangentially into the first round's end arc on x = 0 (a quarter circle about y = -19, z = 8, convex), which runs on at (0, -19, 10) into the left top edge (x=0, z=10, y -19..0), ending on the back face y = 0, square to it. The three are the corner's other two edges and the arc between: the result is the part with all three edges at (0, -21, 10) rolled by the R2 ball, its corner the ball's eighth about (2, -19, 8) (the arc's round is the torus of tube centre radius 0 about the first round's axis, the ball itself). With A = (4 - pi) the R2 spandrel: the upright removes 8 A and the left top edge 19 A; in the corner cube [0,2] x [-21,-19] x [8,10] the first round left the quarter cylinder 2 pi and the ball leaves its eighth 4 pi/3: 2 pi/3. V = 9591.394099 - 35.344727 - 27 A - 2 pi/3 = 9530.777979. Faces: the part's 6, the first round, and the chain's three (cylinder, sphere, cylinder): 10. Each round meets the faces it rolls on G1: graded at its seams' middles (the top front round's at z = 8 on the front and y = -19 on the top; the uprights' at their contacts, z = 5).", "body_count": 1, "watertight": true, "continuity": { @@ -32,5 +32,7 @@ 5 ] ] - } + }, + "volume_mm3": 9530.777979288185, + "faces": 10 } diff --git a/tests/kernel-cases/fillets/every-block-cylinder-tangent-concave-arc-r2-no-tangent-chain/expected.json b/tests/kernel-cases/fillets/every-block-cylinder-tangent-concave-arc-r2-no-tangent-chain/expected.json index b7dd93008..bc82924a9 100644 --- a/tests/kernel-cases/fillets/every-block-cylinder-tangent-concave-arc-r2-no-tangent-chain/expected.json +++ b/tests/kernel-cases/fillets/every-block-cylinder-tangent-concave-arc-r2-no-tangent-chain/expected.json @@ -1,11 +1,10 @@ { "sources": [], - "what": "the concave half circle where a block as wide as the cylinder's diameter meets the cylinder's wall above its top, rounded r2 alone (Tangent chain off)", + "what": "the concave half circle where a block as wide as the cylinder's diameter meets the cylinder's wall above its top, rounded r2 with its tangent chain: the half circle's pieces, ending where it runs on into the block's convex top-side edges", "source": "analytic", - "method": "block 40x20x15 (x 0..40, y -10..10) joined to the cylinder R10 x 30 on the z axis: the block's sides y = +-10 run tangent into the cylinder wall at x = 0; V0 = 12000 + 3000 pi - 15 * 50 pi = 19068.5835. The arc (z = 15, rho = 10, x > 0) ends at (0, +-10, 15), where the block's top-side edges go on tangentially. Rounded r2 alone, the round adds the spandrel (rho in [10,12], z in [15,17]) over the block only, between its side planes |y| = 10: at radius rho it spans 2 asin(10/rho), running out to nothing at the ends. Added = int over the spandrel of 2 rho asin(10/rho) (Gauss-Legendre) = 23.3785. V = 19091.9620. Or a refusal saying the edge continues tangentially (as fillets/1207-fillet-bar-top-edge-after-boss-arc-round-no-tangent-chain).", + "method": "block 40x20x15 (x 0..40, y -10..10) joined to the cylinder R10 x 30 on the z axis: the block's sides y = +-10 run tangent into the cylinder wall at x = 0; V0 = 12000 + 3000 pi - 15 * 50 pi = 19068.5835. The arc (z = 15, rho = 10, x > 0) ends at (0, +-10, 15), where the block's top-side edges go on tangentially. Rounded r2 with its tangent chain: SMLib splits the half circle, and the chain takes every piece of it (concave, tangent at their ends); at (0, +-10, 15) it runs on into convex edges, where a chain ends (a round cannot pass from one side of the faces to the other), so the half circle is rounded whole and alone; the round adds the spandrel (rho in [10,12], z in [15,17]) over the block only, between its side planes |y| = 10: at radius rho it spans 2 asin(10/rho), running out to nothing at the ends. Added = int over the spandrel of 2 rho asin(10/rho) (Gauss-Legendre) = 23.3785. V = 19091.9620.", "body_count": 1, - "outcome": "solid_or_refused", - "refusal": "continues tangentially", + "outcome": "solid", "volume_mm3": 19091.962003483477, "continuity": { "order": "g1" diff --git a/tests/kernel-cases/fillets/every-block-cylinder-tangent-concave-arc-r2-partial-chain/expected.json b/tests/kernel-cases/fillets/every-block-cylinder-tangent-concave-arc-r2-partial-chain/expected.json new file mode 100644 index 000000000..b189b5ea8 --- /dev/null +++ b/tests/kernel-cases/fillets/every-block-cylinder-tangent-concave-arc-r2-partial-chain/expected.json @@ -0,0 +1,13 @@ +{ + "sources": [], + "what": "the concave half circle where a block as wide as the cylinder's diameter meets the cylinder's wall above its top, rounded r2 alone (Tangent chain off)", + "source": "analytic", + "method": "block 40x20x15 (x 0..40, y -10..10) joined to the cylinder R10 x 30 on the z axis: the block's sides y = +-10 run tangent into the cylinder wall at x = 0; V0 = 12000 + 3000 pi - 15 * 50 pi = 19068.5835. The arc (z = 15, rho = 10, x > 0) ends at (0, +-10, 15), where the block's top-side edges go on tangentially. Rounded r2 alone, the round adds the spandrel (rho in [10,12], z in [15,17]) over the block only, between its side planes |y| = 10: at radius rho it spans 2 asin(10/rho), running out to nothing at the ends. Added = int over the spandrel of 2 rho asin(10/rho) (Gauss-Legendre) = 23.3785. V = 19091.9620. Or a refusal saying the edge continues tangentially (as fillets/1207-fillet-bar-top-edge-after-boss-arc-round-partial-chain).", + "body_count": 1, + "outcome": "solid_or_refused", + "refusal": "continues tangentially", + "volume_mm3": 19091.962003483477, + "continuity": { + "order": "g1" + } +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-block-cylinder-tangent-concave-arc-r2-partial-chain/recipe.json b/tests/kernel-cases/fillets/every-block-cylinder-tangent-concave-arc-r2-partial-chain/recipe.json new file mode 100644 index 000000000..c7f769528 --- /dev/null +++ b/tests/kernel-cases/fillets/every-block-cylinder-tangent-concave-arc-r2-partial-chain/recipe.json @@ -0,0 +1,48 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 40, + "width": 20, + "height": 15, + "corner": [ + 0, + -10, + 0 + ], + "body_name": "Block" + } + }, + { + "command": "solid.cylinder", + "params": { + "radius": 10, + "height": 30, + "base": [ + 0, + 0, + 0 + ], + "operation": "join", + "targets": [ + "Block" + ] + } + }, + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 10, + 0, + 15 + ] + ], + "radius": 2, + "tangent_chain": false + } + } + ] +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-fillet-after-fillet-curvature-front-then-side-r3-partial-chain/expected.json b/tests/kernel-cases/fillets/every-fillet-after-fillet-curvature-front-then-side-r3-partial-chain/expected.json new file mode 100644 index 000000000..8dfb1228e --- /dev/null +++ b/tests/kernel-cases/fillets/every-fillet-after-fillet-curvature-front-then-side-r3-partial-chain/expected.json @@ -0,0 +1,12 @@ +{ + "sources": [], + "what": "a box's top front edge rounded curvature-continuous size 3, then the top side edge meeting it at the corner rounded the same way alone (Tangent chain off)", + "source": "invariants", + "method": "box 40x30x20; the edge y=0, z=20 rounded type curvature 3 (every-box-edge-r3-curvature's section), then the edge x=40, z=20 (now y 3..30) rounded type curvature 3 alone: at y = 3 it runs on tangentially into the first round's end curve on x = 40 (the order-2 section, tangent to the top there), so the second round ends on a curved round, not a planar end face: no closed form. A valid body with every blend seam G2, or a refusal saying the edge continues tangentially (the 1207 precedent).", + "body_count": 1, + "outcome": "solid_or_refused", + "refusal": "continues tangentially", + "continuity": { + "order": "g2" + } +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-fillet-after-fillet-curvature-front-then-side-r3-partial-chain/recipe.json b/tests/kernel-cases/fillets/every-fillet-after-fillet-curvature-front-then-side-r3-partial-chain/recipe.json new file mode 100644 index 000000000..70928417e --- /dev/null +++ b/tests/kernel-cases/fillets/every-fillet-after-fillet-curvature-front-then-side-r3-partial-chain/recipe.json @@ -0,0 +1,42 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 40, + "width": 30, + "height": 20, + "body_name": "Part" + } + }, + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 20, + 0, + 20 + ] + ], + "radius": 3, + "type": "curvature" + } + }, + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 40, + 15, + 20 + ] + ], + "radius": 3, + "type": "curvature", + "tangent_chain": false + } + } + ] +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-fillet-after-fillet-curvature-front-then-side-r3/expected.json b/tests/kernel-cases/fillets/every-fillet-after-fillet-curvature-front-then-side-r3/expected.json index 8dfb1228e..40e08c24a 100644 --- a/tests/kernel-cases/fillets/every-fillet-after-fillet-curvature-front-then-side-r3/expected.json +++ b/tests/kernel-cases/fillets/every-fillet-after-fillet-curvature-front-then-side-r3/expected.json @@ -1,12 +1,8 @@ { "sources": [], - "what": "a box's top front edge rounded curvature-continuous size 3, then the top side edge meeting it at the corner rounded the same way alone (Tangent chain off)", - "source": "invariants", - "method": "box 40x30x20; the edge y=0, z=20 rounded type curvature 3 (every-box-edge-r3-curvature's section), then the edge x=40, z=20 (now y 3..30) rounded type curvature 3 alone: at y = 3 it runs on tangentially into the first round's end curve on x = 40 (the order-2 section, tangent to the top there), so the second round ends on a curved round, not a planar end face: no closed form. A valid body with every blend seam G2, or a refusal saying the edge continues tangentially (the 1207 precedent).", - "body_count": 1, - "outcome": "solid_or_refused", - "refusal": "continues tangentially", - "continuity": { - "order": "g2" - } + "what": "a box's top front edge rounded curvature-continuous size 3, then the top side edge meeting it at the corner rounded the same way with its tangent chain, which runs on round the first round's end curve: refused, the size 3 has no room there", + "source": "analytic", + "method": "box 40x30x20; the edge y=0, z=20 rounded type curvature 3 (every-box-edge-r3-curvature's section), then the edge x=40, z=20 (now y 3..30) rounded type curvature 3 with its tangent chain: at y = 3 it runs on tangentially into the first round's end curve on x = 40 (the order-2 section, tangent to the top there; convex), which runs on at (40, 0, 17) into the front upright (x=40, y=0, z 0..17). Along the end curve the second blend's contact line on x = 40 is that curve offset 3 towards its centres of curvature. The section turns 90 degrees from (3, 0) on the top to (0, 3) on the side; with rho(phi) its radius of curvature at tangent angle phi, its setback along the top is 3 = Int_0^(pi/2) rho(phi) cos(phi) dphi, and Int_0^(pi/2) cos(phi) dphi = 1, so 3 is a weighted mean of rho; the order-2 section's curvature is 0 at both ends (rho unbounded there), so rho is not constant and its least value is below 3. The offset by 3 passes that curve's evolute and folds back on itself: the blend passes through itself (as ladder 07-fillets/016's r7 on the r5 round's arc). No such blend exists, so the right answer is a clean refusal for its size.", + "outcome": "refused", + "refusal": "larger than the faces beside its edges allow" } \ No newline at end of file diff --git a/tests/kernel-cases/ladder/07-fillets/020-corner-three-sequential-r5-r3-r7-partial-chain/expected.json b/tests/kernel-cases/ladder/07-fillets/020-corner-three-sequential-r5-r3-r7-partial-chain/expected.json new file mode 100644 index 000000000..56a721d47 --- /dev/null +++ b/tests/kernel-cases/ladder/07-fillets/020-corner-three-sequential-r5-r3-r7-partial-chain/expected.json @@ -0,0 +1,8 @@ +{ + "sources": [], + "what": "rounds r5 and r3 on the two top edges at a corner, the r3 on its edge alone (Tangent chain off, so it ends where the edge runs on into the r5 round's end arc), then r7 on the vertical edge under them: refused, the r7 cannot exist", + "source": "invariants", + "method": "the r7 runs on (tangent chain) up the side x=60 along its arc on the r5 round, a circle of radius 5 about the r5 axis: the r7's contact line on that face would be the arc offset 7 towards its centre, radius 5 - 7 < 0, so the blend passes through itself; and along the seam of the r5 and r3 rounds no ball over r3 fits the r3 round. No such round exists, so the right answer is a clean refusal (SMLib: no room for the rolling ball). 021 is the same corner with a radius that fits.", + "outcome": "refused", + "refusal": "the fillet is larger than the faces beside its edges allow" +} diff --git a/tests/kernel-cases/ladder/07-fillets/020-corner-three-sequential-r5-r3-r7-partial-chain/recipe.json b/tests/kernel-cases/ladder/07-fillets/020-corner-three-sequential-r5-r3-r7-partial-chain/recipe.json new file mode 100644 index 000000000..ab2c565c0 --- /dev/null +++ b/tests/kernel-cases/ladder/07-fillets/020-corner-three-sequential-r5-r3-r7-partial-chain/recipe.json @@ -0,0 +1,45 @@ +{ + "base": "../../01-primitives/001-box", + "commands": [ + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 30, + 40, + 20 + ] + ], + "radius": 5 + } + }, + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 60, + 20, + 20 + ] + ], + "radius": 3, + "tangent_chain": false + } + }, + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 60, + 40, + 8 + ] + ], + "radius": 7 + } + } + ] +} diff --git a/tests/kernel-cases/ladder/07-fillets/021-corner-three-sequential-r5-r3-r2-partial-chain/expected.json b/tests/kernel-cases/ladder/07-fillets/021-corner-three-sequential-r5-r3-r2-partial-chain/expected.json new file mode 100644 index 000000000..0937f5e48 --- /dev/null +++ b/tests/kernel-cases/ladder/07-fillets/021-corner-three-sequential-r5-r3-r2-partial-chain/expected.json @@ -0,0 +1,20 @@ +{ + "sources": [], + "what": "rounds r5 and r3 on the two top edges at a corner, the r3 on its edge alone (Tangent chain off, so it ends where the edge runs on into the r5 round's end arc), then r2 on the vertical edge under them, run on up into the corner", + "source": "invariants", + "method": "as 020 with a radius that fits (r < 3, the smaller top round): the r2 runs up the vertical edge and on along the side's arc on the r5 round and the seam between the two rounds, tapering to a point where they become tangent. Faces: the box's 6 and the two top rounds, + 3 for the r2 (along the vertical edge, up the arc, along the seam); one valid body inside the box", + "body_count": 1, + "faces": 11, + "bbox": { + "min": [ + 0, + 0, + 0 + ], + "max": [ + 60, + 40, + 20 + ] + } +} diff --git a/tests/kernel-cases/ladder/07-fillets/021-corner-three-sequential-r5-r3-r2-partial-chain/recipe.json b/tests/kernel-cases/ladder/07-fillets/021-corner-three-sequential-r5-r3-r2-partial-chain/recipe.json new file mode 100644 index 000000000..0dba98b4a --- /dev/null +++ b/tests/kernel-cases/ladder/07-fillets/021-corner-three-sequential-r5-r3-r2-partial-chain/recipe.json @@ -0,0 +1,45 @@ +{ + "base": "../../01-primitives/001-box", + "commands": [ + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 30, + 40, + 20 + ] + ], + "radius": 5 + } + }, + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 60, + 20, + 20 + ] + ], + "radius": 3, + "tangent_chain": false + } + }, + { + "command": "solid.fillet", + "params": { + "edges": [ + [ + 60, + 40, + 8 + ] + ], + "radius": 2 + } + } + ] +} diff --git a/tests/kernel-cases/ladder/ladder.json b/tests/kernel-cases/ladder/ladder.json index dab9df7ed..a748545dc 100644 --- a/tests/kernel-cases/ladder/ladder.json +++ b/tests/kernel-cases/ladder/ladder.json @@ -156,7 +156,9 @@ "ladder/07-fillets/003-tangent-chain-r3", "ladder/07-fillets/017-part-rounds", "ladder/07-fillets/019-concave-corner-g2-patch", - "ladder/07-fillets/015-corner-g2-patch" + "ladder/07-fillets/015-corner-g2-patch", + "ladder/07-fillets/020-corner-three-sequential-r5-r3-r7-partial-chain", + "ladder/07-fillets/021-corner-three-sequential-r5-r3-r2-partial-chain" ], "tier": "07-fillets", "what": "constant, variable and corner fillets"