diff --git a/tests/kernel-cases/fillets/KNOWN_FAILING b/tests/kernel-cases/fillets/KNOWN_FAILING index 170fc6f1e..357e91a39 100644 --- a/tests/kernel-cases/fillets/KNOWN_FAILING +++ b/tests/kernel-cases/fillets/KNOWN_FAILING @@ -8,6 +8,8 @@ 9-fillet-corner-curvature-with-reduce-fit not supported yet: solid.fillet builds corner g2 with the exact fit only 9-fillet-corner-curvature-with-taper-fit not supported yet: solid.fillet builds corner g2 with the exact fit only every-block-cylinder-crease-top-edge-after-arc-round-r1 the r1 round's contact seam with the block's side face reads 60 degrees (the cylinder wall's normal) at its end on the crease (8.660, 5, 15.284): G0 where the round is built tangent +every-chamfer-pocket-rim-5-5-refused refused naming 5 mm as the largest distance: the full-width chamfer (legs as deep as the 5 mm walls) builds instead of being refused +every-chamfer-pocket-rim-5-full-depth-refused the full-width chamfer (legs as deep as the 5 mm walls) builds instead of being refused every-hole-top-rim-chamfer-10-full-depth-refused the full-width chamfer (leg as deep as the 10 mm plate) builds instead of being refused every-hole-top-rim-r12-past-plate-bottom SMLib status 1001: a convex round past its face on the tangent side is not yet built by subtraction every-pocket-floor-and-rim-edges-r2 a corner patch where two rim rounds meet at each concave pocket corner (23 faces, not 19) instead of the mitre the rounds make running into each other diff --git a/tests/kernel-cases/fillets/every-chamfer-box-edge-2/expected.json b/tests/kernel-cases/fillets/every-chamfer-box-edge-2/expected.json new file mode 100644 index 000000000..212499504 --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-box-edge-2/expected.json @@ -0,0 +1,24 @@ +{ + "sources": [], + "what": "a box's top front edge chamfered 2", + "source": "analytic", + "method": "box 40x30x20, the edge y=0, z=20 chamfered 2: the right triangle of legs 2 (area 2) along 40: V = 24000 - 80 = 23920. Faces 7; creases (G0).", + "body_count": 1, + "volume_mm3": 23920.0, + "faces": 7, + "bbox": { + "min": [ + 0, + 0, + 0 + ], + "max": [ + 40, + 30, + 20 + ] + }, + "continuity": { + "order": "g0" + } +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-box-edge-2/recipe.json b/tests/kernel-cases/fillets/every-chamfer-box-edge-2/recipe.json new file mode 100644 index 000000000..c12606a09 --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-box-edge-2/recipe.json @@ -0,0 +1,26 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 40, + "width": 30, + "height": 20, + "body_name": "Part" + } + }, + { + "command": "solid.chamfer", + "params": { + "edges": [ + [ + 20, + 0, + 20 + ] + ], + "distance": 2 + } + } + ] +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1-flipped/expected.json b/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1-flipped/expected.json new file mode 100644 index 000000000..a50c8cbe3 --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1-flipped/expected.json @@ -0,0 +1,20 @@ +{ + "sources": [], + "what": "a box's top front edge chamfered by two distances, flipped: 3 down the front and 1 along the top", + "source": "analytic", + "method": "as every-chamfer-box-edge-two-distances-3-1 with `flip`: the front face first, so the triangle (0,20), (1,20), (0,17), area 1.5, V = 23940, its centroid (1/3, 19): centre of mass (20, (360000 - 20)/23940, (240000 - 60 * 19)/23940), graded to 0.0005 mm. Faces 7.", + "body_count": 1, + "volume_mm3": 23940.0, + "faces": 7, + "center_of_mass": [ + 20.0, + 15.036758563074352, + 9.977443609022556 + ], + "tolerance": { + "abs_mm": 0.0005 + }, + "continuity": { + "order": "g0" + } +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1-flipped/recipe.json b/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1-flipped/recipe.json new file mode 100644 index 000000000..1b08099fe --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1-flipped/recipe.json @@ -0,0 +1,28 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 40, + "width": 30, + "height": 20, + "body_name": "Part" + } + }, + { + "command": "solid.chamfer", + "params": { + "edges": [ + [ + 20, + 0, + 20 + ] + ], + "distance": 3, + "distance2": 1, + "flip": true + } + } + ] +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1/expected.json b/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1/expected.json new file mode 100644 index 000000000..368ed1ff6 --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1/expected.json @@ -0,0 +1,20 @@ +{ + "sources": [], + "what": "a box's top front edge chamfered by two distances: 3 along the top (the first face, the one facing up) and 1 down the front", + "source": "analytic", + "method": "box 40x30x20, the edge y=0, z=20: the triangle (0,20), (3,20), (0,19) in (y,z), area 1.5, along 40: V = 24000 - 60 = 23940. Its centroid (1, 59/3) fixes which leg went where: centre of mass (20, (360000 - 60)/23940, (240000 - 60 * 59/3)/23940), graded to 0.0005 mm (flipped, it moves 0.0017 mm in y and z). Faces 7.", + "body_count": 1, + "volume_mm3": 23940.0, + "faces": 7, + "center_of_mass": [ + 20.0, + 15.035087719298245, + 9.97577276524645 + ], + "tolerance": { + "abs_mm": 0.0005 + }, + "continuity": { + "order": "g0" + } +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1/recipe.json b/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1/recipe.json new file mode 100644 index 000000000..ac7839d2d --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-box-edge-two-distances-3-1/recipe.json @@ -0,0 +1,27 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 40, + "width": 30, + "height": 20, + "body_name": "Part" + } + }, + { + "command": "solid.chamfer", + "params": { + "edges": [ + [ + 20, + 0, + 20 + ] + ], + "distance": 3, + "distance2": 1 + } + } + ] +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-pocket-rim-1/expected.json b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-1/expected.json new file mode 100644 index 000000000..82db428b7 --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-1/expected.json @@ -0,0 +1,24 @@ +{ + "sources": [], + "what": "a rectangular pocket's four rim edges chamfered 1", + "source": "analytic", + "method": "plate 60x40x10 with the pocket 30x20x5 (x 15..45, y 10..30, floor z = 5, sharp vertical corners): V0 = 24000 - 3000 = 21000. Each convex rim edge loses the triangle d^2/2 along its length (100 in all); at each pocket corner the two chamfers run on past it and meet in a mitre, the quadrant losing what both remove: points (s, t) past both walls with s + u < d and t + u < d (u the depth), int_0^d (d-u)^2 du = d^3/3. d = 1: removed = 50 d^2 + (4/3) d^3 = 51.3333. V = 20948.6667. Faces 15.", + "body_count": 1, + "volume_mm3": 20948.666666666668, + "faces": 15, + "bbox": { + "min": [ + 0, + 0, + 0 + ], + "max": [ + 60, + 40, + 10 + ] + }, + "continuity": { + "order": "g0" + } +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-pocket-rim-1/recipe.json b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-1/recipe.json new file mode 100644 index 000000000..e4a9f007e --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-1/recipe.json @@ -0,0 +1,58 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 60, + "width": 40, + "height": 10, + "body_name": "Plate" + } + }, + { + "command": "solid.box", + "params": { + "length": 30, + "width": 20, + "height": 6, + "corner": [ + 15, + 10, + 5 + ], + "operation": "cut", + "targets": [ + "Plate" + ] + } + }, + { + "command": "solid.chamfer", + "params": { + "edges": [ + [ + 30, + 10, + 10 + ], + [ + 30, + 30, + 10 + ], + [ + 15, + 20, + 10 + ], + [ + 45, + 20, + 10 + ] + ], + "distance": 1 + } + } + ] +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-pocket-rim-4-9-fits/expected.json b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-4-9-fits/expected.json new file mode 100644 index 000000000..8f7ff1d44 --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-4-9-fits/expected.json @@ -0,0 +1,24 @@ +{ + "sources": [], + "what": "a 5 mm deep pocket's rim edges chamfered 4.9: the legs stop 0.1 short of the floor, so it fits", + "source": "analytic", + "method": "plate 60x40x10 with the pocket 30x20x5 (x 15..45, y 10..30, floor z = 5, sharp vertical corners): V0 = 24000 - 3000 = 21000. Each convex rim edge loses the triangle d^2/2 along its length (100 in all); at each pocket corner the two chamfers run on past it and meet in a mitre, the quadrant losing what both remove: points (s, t) past both walls with s + u < d and t + u < d (u the depth), int_0^d (d-u)^2 du = d^3/3. d = 4.9: removed = 50 d^2 + (4/3) d^3 = 1357.3653. V = 19642.6347. Faces 15.", + "body_count": 1, + "volume_mm3": 19642.634666666665, + "faces": 15, + "bbox": { + "min": [ + 0, + 0, + 0 + ], + "max": [ + 60, + 40, + 10 + ] + }, + "continuity": { + "order": "g0" + } +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-pocket-rim-4-9-fits/recipe.json b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-4-9-fits/recipe.json new file mode 100644 index 000000000..7c8c57b32 --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-4-9-fits/recipe.json @@ -0,0 +1,58 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 60, + "width": 40, + "height": 10, + "body_name": "Plate" + } + }, + { + "command": "solid.box", + "params": { + "length": 30, + "width": 20, + "height": 6, + "corner": [ + 15, + 10, + 5 + ], + "operation": "cut", + "targets": [ + "Plate" + ] + } + }, + { + "command": "solid.chamfer", + "params": { + "edges": [ + [ + 30, + 10, + 10 + ], + [ + 30, + 30, + 10 + ], + [ + 15, + 20, + 10 + ], + [ + 45, + 20, + 10 + ] + ], + "distance": 4.9 + } + } + ] +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-5-refused/expected.json b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-5-refused/expected.json new file mode 100644 index 000000000..0b13ada99 --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-5-refused/expected.json @@ -0,0 +1,8 @@ +{ + "sources": [], + "what": "a 5 mm deep pocket's rim edges chamfered 5.5: the legs would run off the walls over the floor: refused, naming the largest distance that fits", + "source": "invariants", + "method": "owner rule: a chamfer whose leg runs off the face beside its edge over another face is refused, naming the largest size that fits, and a full-width chamfer stays refused. The walls are 5 deep, so every distance below 5 fits (every-chamfer-pocket-rim-4-9-fits) and 5 does not; the search names the largest at the request's three significant digits (step 0.001): 4.999.", + "outcome": "refused", + "refusal": "the largest distance that fits is 4.999 mm" +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-5-refused/recipe.json b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-5-refused/recipe.json new file mode 100644 index 000000000..c4aa23aa1 --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-5-refused/recipe.json @@ -0,0 +1,58 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 60, + "width": 40, + "height": 10, + "body_name": "Plate" + } + }, + { + "command": "solid.box", + "params": { + "length": 30, + "width": 20, + "height": 6, + "corner": [ + 15, + 10, + 5 + ], + "operation": "cut", + "targets": [ + "Plate" + ] + } + }, + { + "command": "solid.chamfer", + "params": { + "edges": [ + [ + 30, + 10, + 10 + ], + [ + 30, + 30, + 10 + ], + [ + 15, + 20, + 10 + ], + [ + 45, + 20, + 10 + ] + ], + "distance": 5.5 + } + } + ] +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-full-depth-refused/expected.json b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-full-depth-refused/expected.json new file mode 100644 index 000000000..5e695113e --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-full-depth-refused/expected.json @@ -0,0 +1,8 @@ +{ + "sources": [], + "what": "a 5 mm deep pocket's rim edges chamfered 5: the legs would use the whole walls: refused, naming the largest distance that fits", + "source": "invariants", + "method": "owner rule: a chamfer whose leg runs off the face beside its edge over another face is refused, naming the largest size that fits, and a full-width chamfer stays refused. The walls are 5 deep, so every distance below 5 fits (every-chamfer-pocket-rim-4-9-fits) and 5 does not; the search names the largest at the request's three significant digits (step 0.001): 4.999.", + "outcome": "refused", + "refusal": "the largest distance that fits is 4.999 mm" +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-full-depth-refused/recipe.json b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-full-depth-refused/recipe.json new file mode 100644 index 000000000..2bfec181e --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-5-full-depth-refused/recipe.json @@ -0,0 +1,58 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 60, + "width": 40, + "height": 10, + "body_name": "Plate" + } + }, + { + "command": "solid.box", + "params": { + "length": 30, + "width": 20, + "height": 6, + "corner": [ + 15, + 10, + 5 + ], + "operation": "cut", + "targets": [ + "Plate" + ] + } + }, + { + "command": "solid.chamfer", + "params": { + "edges": [ + [ + 30, + 10, + 10 + ], + [ + 30, + 30, + 10 + ], + [ + 15, + 20, + 10 + ], + [ + 45, + 20, + 10 + ] + ], + "distance": 5 + } + } + ] +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-pocket-rim-two-distances-2-1/expected.json b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-two-distances-2-1/expected.json new file mode 100644 index 000000000..9caa1122b --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-two-distances-2-1/expected.json @@ -0,0 +1,24 @@ +{ + "sources": [], + "what": "a rectangular pocket's rim edges chamfered by two distances: 2 along the top (facing up) and 1 down the walls", + "source": "analytic", + "method": "plate 60x40x10 with the pocket 30x20x5 (x 15..45, y 10..30, floor z = 5, sharp vertical corners): V0 = 24000 - 3000 = 21000. Each rim edge loses the triangle of legs 2 (on the top) and 1 (down the wall), area 1, along 100; at each corner the mitred quadrant loses the points past both walls with s/2 + u < 1 and t/2 + u < 1: int_0^1 (2 (1-u))^2 du = 4/3. Removed = 100 + 16/3 = 105.3333. V = 20894.6667. Faces 15.", + "body_count": 1, + "volume_mm3": 20894.666666666668, + "faces": 15, + "bbox": { + "min": [ + 0, + 0, + 0 + ], + "max": [ + 60, + 40, + 10 + ] + }, + "continuity": { + "order": "g0" + } +} \ No newline at end of file diff --git a/tests/kernel-cases/fillets/every-chamfer-pocket-rim-two-distances-2-1/recipe.json b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-two-distances-2-1/recipe.json new file mode 100644 index 000000000..2159a83da --- /dev/null +++ b/tests/kernel-cases/fillets/every-chamfer-pocket-rim-two-distances-2-1/recipe.json @@ -0,0 +1,59 @@ +{ + "commands": [ + { + "command": "solid.box", + "params": { + "length": 60, + "width": 40, + "height": 10, + "body_name": "Plate" + } + }, + { + "command": "solid.box", + "params": { + "length": 30, + "width": 20, + "height": 6, + "corner": [ + 15, + 10, + 5 + ], + "operation": "cut", + "targets": [ + "Plate" + ] + } + }, + { + "command": "solid.chamfer", + "params": { + "edges": [ + [ + 30, + 10, + 10 + ], + [ + 30, + 30, + 10 + ], + [ + 15, + 20, + 10 + ], + [ + 45, + 20, + 10 + ] + ], + "distance": 2, + "distance2": 1 + } + } + ] +} \ No newline at end of file