first commit
This commit is contained in:
commit
4e80084820
|
|
@ -0,0 +1,550 @@
|
|||
#-------------------------------------
|
||||
# Ender 5 Plus w/ SKR 1.4
|
||||
# v. 0.10
|
||||
#-------------------------------------
|
||||
|
||||
[include mainsail.cfg]
|
||||
|
||||
#-------------------------------------
|
||||
# Firmware Retraction
|
||||
#-------------------------------------
|
||||
# [firmware_retraction]
|
||||
# retract_length: 0.8
|
||||
# retract_speed: 60
|
||||
# unretract_extra_length: 0
|
||||
# unretract_speed: 60
|
||||
|
||||
#-------------------------------------
|
||||
# Pressure Advance
|
||||
#-------------------------------------
|
||||
# [extruder]
|
||||
# pressure_advance: 0.0 # Overture PLA
|
||||
|
||||
#-------------------------------------
|
||||
# Input Shaper
|
||||
#-------------------------------------
|
||||
#[mcu rpi]
|
||||
#serial: /tmp/klipper_host_mcu
|
||||
|
||||
#[adxl345]
|
||||
#cs_pin: rpi:None
|
||||
|
||||
#[resonance_tester]
|
||||
#accel_chip: adxl345
|
||||
#probe_points:
|
||||
# 180, 180, 20 # an example
|
||||
#-------------------------------------
|
||||
# Extruder
|
||||
#-------------------------------------
|
||||
[extruder]
|
||||
step_pin: P2.13
|
||||
dir_pin: !P0.11
|
||||
enable_pin: !P2.12
|
||||
microsteps: 16
|
||||
rotation_distance: 32.85
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: P2.7
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: P0.24
|
||||
min_temp: 0
|
||||
max_temp: 260
|
||||
max_extrude_only_distance: 500
|
||||
|
||||
#-------------------------------------
|
||||
# Printer General
|
||||
#-------------------------------------
|
||||
[safe_z_home]
|
||||
home_xy_position: 180, 180
|
||||
speed: 100
|
||||
z_hop: 10
|
||||
z_hop_speed: 100
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: P0.10 #Probe
|
||||
control_pin: P2.0 #SERVOS
|
||||
stow_on_each_sample: False
|
||||
probe_with_touch_mode: True
|
||||
pin_up_touch_mode_reports_triggered: False
|
||||
set_output_mode: 5V
|
||||
speed: 100
|
||||
pin_move_time: 0.675
|
||||
lift_speed: 200
|
||||
samples: 4
|
||||
sample_retract_dist: 10
|
||||
#Mount Offset
|
||||
x_offset: -45
|
||||
y_offset: -7
|
||||
|
||||
[bed_mesh]
|
||||
speed: 100
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 5, 15
|
||||
mesh_max: 310,337
|
||||
probe_count: 5,5
|
||||
fade_start: 1
|
||||
fade_end: 10
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: P2.5
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: P0.25
|
||||
max_power: 0.8
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
pwm_cycle_time: 0.01666
|
||||
|
||||
[fan]
|
||||
pin: P2.3
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_lpc1768_2B4003196520BC9568FEE260C32000F5-if00
|
||||
|
||||
[filament_switch_sensor filament_sensor]
|
||||
switch_pin: P1.26
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 60
|
||||
max_accel: 300
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[temperature_sensor raspberry_pi]
|
||||
sensor_type: temperature_host
|
||||
max_temp: 100
|
||||
|
||||
#-------------------------------------
|
||||
# Bed Leveling
|
||||
#-------------------------------------
|
||||
[z_tilt]
|
||||
z_positions: -18.4,180
|
||||
378.4,180
|
||||
points: 38,180
|
||||
360,180
|
||||
speed: 50
|
||||
horizontal_move_z: 5
|
||||
retries: 5
|
||||
retry_tolerance:0.08
|
||||
|
||||
[screws_tilt_adjust]
|
||||
screw1: 71,60
|
||||
screw1_name: front left screw
|
||||
screw2: 332,60
|
||||
screw2_name: front right screw
|
||||
screw3: 332,321
|
||||
screw3_name: rear right screw
|
||||
screw4: 71,321
|
||||
screw4_name: rear left screw
|
||||
horizontal_move_z: 10.
|
||||
speed: 50.
|
||||
screw_thread: CW-M4
|
||||
|
||||
[bed_screws]
|
||||
screw1: 27.5, 47
|
||||
screw2: 327.5, 47
|
||||
screw3: 327.5, 307
|
||||
screw4: 27.5, 307
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
|
||||
EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
|
||||
EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
|
||||
EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
|
||||
|
||||
|
||||
[display]
|
||||
lcd_type: uc1701
|
||||
cs_pin: EXP1_3
|
||||
a0_pin: EXP1_4
|
||||
rst_pin: EXP1_5
|
||||
encoder_pins: ^EXP2_5, ^EXP2_3
|
||||
click_pin: ^!EXP1_2
|
||||
# Prędkość odświeżania wyświetlacza. Zwiększ, jeśli obraz migocze, zmniejsz, jeśli masz problemy z MCU.
|
||||
# Ustaw na 120, jeśli nie masz problemów.
|
||||
spi_speed: 2000000
|
||||
contrast: 63
|
||||
|
||||
[neopixel btt_mini12864]
|
||||
pin: EXP1_6
|
||||
chain_count: 3 # Ten wyświetlacz ma 3 diody RGB
|
||||
color_order: RGB # Sprawdź, czy Twój wyświetlacz ma taki porządek kolorów, inaczej kolory mogą być pomieszane
|
||||
initial_RED: 0.0 # Początkowa jasność czerwonego (0.0 - 1.0)
|
||||
initial_GREEN: 0.5 # Początkowa jasność zielonego (0.0 - 1.0)
|
||||
initial_BLUE: 0.0 # Początkowa jasność niebieskiego (0.0 - 1.0)
|
||||
|
||||
#-------------------------------------
|
||||
# Others
|
||||
#-------------------------------------
|
||||
[force_move]
|
||||
enable_force_move: True
|
||||
[virtual_sdcard]
|
||||
path: /home/pali112/printer_data/gcodes
|
||||
[exclude_object]
|
||||
[display_status]
|
||||
[pause_resume]
|
||||
#[respond]
|
||||
# default_type: echo
|
||||
|
||||
[idle_timeout]
|
||||
timeout: 1800
|
||||
gcode:
|
||||
TURN_OFF_HEATERS
|
||||
|
||||
#-------------------------------------
|
||||
# Stepper Drivers
|
||||
#-------------------------------------
|
||||
[tmc2208 stepper_x]
|
||||
uart_pin: P1.10
|
||||
interpolate: False
|
||||
sense_resistor: 0.110
|
||||
run_current: 0.80
|
||||
#hold_current: 0.500
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
|
||||
[tmc2208 stepper_y]
|
||||
uart_pin: P1.9
|
||||
interpolate: False
|
||||
sense_resistor: 0.110
|
||||
run_current: 0.80
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[tmc2208 stepper_z] #z
|
||||
uart_pin: P1.8
|
||||
interpolate: False
|
||||
sense_resistor: 0.110
|
||||
run_current: 0.80
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[tmc2208 stepper_z1] #z1
|
||||
uart_pin: P1.1
|
||||
interpolate: False
|
||||
sense_resistor: 0.110
|
||||
run_current: 0.80
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[tmc2208 extruder]
|
||||
uart_pin: P1.4
|
||||
run_current: 0.80
|
||||
interpolate: False
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
# -------------------------------------
|
||||
# Steppers
|
||||
# -------------------------------------
|
||||
[stepper_x]
|
||||
step_pin: P2.2
|
||||
dir_pin: !P2.6
|
||||
enable_pin: !P2.1
|
||||
microsteps: 16
|
||||
rotation_distance: 39.88
|
||||
endstop_pin: P1.29
|
||||
position_endstop: 360
|
||||
position_min: 0
|
||||
position_max: 360
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 5
|
||||
|
||||
[stepper_y]
|
||||
step_pin: P0.19
|
||||
dir_pin: !P0.20
|
||||
enable_pin: !P2.8
|
||||
microsteps: 16
|
||||
rotation_distance: 39.83
|
||||
endstop_pin: P1.28
|
||||
position_endstop: 360
|
||||
position_min: 0
|
||||
position_max: 360
|
||||
homing_speed: 50
|
||||
homing_retract_dist: 5
|
||||
|
||||
# [stepper_z]
|
||||
# step_pin: P1.15
|
||||
# dir_pin: !P1.14
|
||||
# enable_pin: !P1.27
|
||||
# microsteps: 16
|
||||
# rotation_distance: 4
|
||||
# endstop_pin: probe:z_virtual_endstop
|
||||
# position_max: 400
|
||||
# position_min: -5
|
||||
|
||||
# [stepper_z1]
|
||||
# step_pin: P0.22
|
||||
# dir_pin: !P2.11
|
||||
# enable_pin: !P0.21
|
||||
# microsteps: 16
|
||||
# rotation_distance: 4
|
||||
# endstop_pin: probe:z_virtual_endstop
|
||||
|
||||
[stepper_z]
|
||||
step_pin: P0.22
|
||||
dir_pin: !P2.11 # Upewnij się co do '!' (próba ruchu i zmiana jeśli trzeba)
|
||||
enable_pin: !P0.21 # Upewnij się co do '!' (próba ruchu i zmiana jeśli trzeba)
|
||||
microsteps: 16
|
||||
rotation_distance: 4
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_max: 400
|
||||
position_min: -5
|
||||
|
||||
[stepper_z1]
|
||||
step_pin: P1.15
|
||||
dir_pin: !P1.14 # Upewnij się co do '!'
|
||||
enable_pin: !P1.16 # Upewnij się co do '!'
|
||||
microsteps: 16
|
||||
rotation_distance: 4
|
||||
endstop_pin: probe:z_virtual_endstop # Tak, również dla tego silnika BLTouch jest referencją
|
||||
# Brak position_max i position_min - to jest poprawne dla dodatkowych silników
|
||||
|
||||
|
||||
|
||||
#-------------------------------------
|
||||
# Macros
|
||||
#-------------------------------------
|
||||
|
||||
[gcode_macro START_PRINT]
|
||||
gcode:
|
||||
{% set BED_TEMP = params.BED_TEMP|default(60)|float %}
|
||||
{% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(210)|float %}
|
||||
G28 ; Homing wszystkich osi
|
||||
|
||||
# Rozpocznij grzanie stołu i ekstrudera do zadanych temperatur
|
||||
M140 S{BED_TEMP} ; Ustaw temperaturę stołu (bez czekania)
|
||||
M104 S{EXTRUDER_TEMP} ; Ustaw temperaturę ekstrudera (bez czekania)
|
||||
|
||||
# Poczekaj, aż stół osiągnie zadaną temperaturę
|
||||
M190 S{BED_TEMP}
|
||||
|
||||
# Poczekaj, aż ekstruder osiągnie zadaną temperaturę
|
||||
M109 S{EXTRUDER_TEMP}
|
||||
|
||||
|
||||
Z_TILT_ADJUST ; Wykonaj regulację Z-Tilt
|
||||
BED_MESH_PROFILE LOAD=default ; Załaduj domyślny profil siatki stołu
|
||||
|
||||
G92 E0 ; Zresetuj ekstruder
|
||||
G1 Z2.0 F3000 ; Podnieś głowicę na wysokość 2 mm
|
||||
G1 X5.1 Y20 Z0.3 F5000.0 ; Przesuń głowicę do pozycji początkowej linii gruntującej
|
||||
G1 X5.1 Y200.0 Z0.3 F1500.0 E15 ; Wytłocz pierwszą część linii gruntującej
|
||||
G1 X5.4 Y200.0 Z0.3 F5000.0 ; Szybki ruch, aby odciągnąć dyszę od wytłoczonej linii
|
||||
G1 X5.4 Y20 Z0.3 F1500.0 E30 ; Wytłocz drugą część linii gruntującej
|
||||
G92 E0 ; Zresetuj ekstruder ponownie
|
||||
G1 Z2.0 F3000 ; Podnieś głowicę ponownie
|
||||
|
||||
|
||||
|
||||
[gcode_macro _CLIENT_VARIABLE]
|
||||
variable_use_custom_pos : False ; use custom park coordinates for x,y [True/False]
|
||||
variable_custom_park_x : 0.0 ; custom x position; value must be within your defined min and max of X
|
||||
variable_custom_park_y : 0.0 ; custom y position; value must be within your defined min and max of Y
|
||||
variable_custom_park_dz : 2.0 ; custom dz value; the value in mm to lift the nozzle when move to park position
|
||||
variable_retract : 1.0 ; the value to retract while PAUSE
|
||||
variable_cancel_retract : 1 ; the value to retract while CANCEL_PRINT
|
||||
variable_speed_retract : 35.0 ; retract speed in mm/s
|
||||
variable_unretract : 1.0 ; the value to unretract while RESUME
|
||||
variable_speed_unretract : 35.0 ; unretract speed in mm/s
|
||||
variable_speed_hop : 15.0 ; z move speed in mm/s
|
||||
variable_speed_move : 100.0 ; move speed in mm/s
|
||||
variable_park_at_cancel : False ; allow to move the toolhead to park while execute CANCEL_PRINT [True,False]
|
||||
## !!! Caution [firmware_retraction] must be defined in the printer.cfg if you set use_fw_retract: True !!!
|
||||
#variable_use_fw_retract : False ; use fw_retraction instead of the manual version [True/False]
|
||||
gcode:
|
||||
|
||||
[gcode_macro BEEP_ALERT]
|
||||
gcode:
|
||||
M300 S200 P200
|
||||
M300 S200 P200
|
||||
M300 S200 P200
|
||||
|
||||
[gcode_macro BEEP_READY]
|
||||
gcode:
|
||||
M300 S500 P50
|
||||
M300 S600 P50
|
||||
M300 S700 P50
|
||||
|
||||
[gcode_macro BEEP_CONFIRM]
|
||||
gcode:
|
||||
M300 S1000 P100
|
||||
M300 S1200 P100
|
||||
M300 S1400 P100
|
||||
|
||||
[gcode_macro G29]
|
||||
gcode:
|
||||
G28
|
||||
M190 S60
|
||||
BED_MESH_CALIBRATE
|
||||
BED_MESH_PROFILE SAVE=default
|
||||
# G1 X0 Y0 Z5 F4000
|
||||
M140 S0
|
||||
|
||||
[gcode_macro PAUSE]
|
||||
description: Pause the actual running print
|
||||
rename_existing: PAUSE_BASE
|
||||
variable_extrude: 1.0
|
||||
gcode:
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
{% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
|
||||
{% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
|
||||
{% set max_z = printer.toolhead.axis_maximum.z|float %}
|
||||
{% set act_z = printer.toolhead.position.z|float %}
|
||||
{% if act_z < (max_z - 2.0) %}
|
||||
{% set z_safe = 2.0 %}
|
||||
{% else %}
|
||||
{% set z_safe = max_z - act_z %}
|
||||
{% endif %}
|
||||
PAUSE_BASE
|
||||
G91
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G1 E-{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
{% if "xyz" in printer.toolhead.homed_axes %}
|
||||
G1 Z{z_safe} F900
|
||||
G90
|
||||
G1 X{x_park} Y{y_park} F6000
|
||||
{% else %}
|
||||
{action_respond_info("Printer not homed")}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro RESUME]
|
||||
description: Resume the actual running print
|
||||
rename_existing: RESUME_BASE
|
||||
gcode:
|
||||
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
|
||||
{% if 'VELOCITY' in params|upper %}
|
||||
{% set get_params = ('VELOCITY=' + params.VELOCITY) %}
|
||||
{%else %}
|
||||
{% set get_params = "" %}
|
||||
{% endif %}
|
||||
{% if printer.extruder.can_extrude|lower == 'true' %}
|
||||
G91
|
||||
G1 E{E} F2100
|
||||
{% else %}
|
||||
{action_respond_info("Extruder not hot enough")}
|
||||
{% endif %}
|
||||
RESUME_BASE {get_params}
|
||||
|
||||
[gcode_macro CANCEL_PRINT]
|
||||
description: Cancel the actual running print
|
||||
rename_existing: CANCEL_PRINT_BASE
|
||||
gcode:
|
||||
# TURN_OFF_HEATERS
|
||||
CANCEL_PRINT_BASE
|
||||
|
||||
[gcode_macro load_mesh]
|
||||
gcode:
|
||||
BED_MESH_PROFILE load=default
|
||||
|
||||
[gcode_macro M300]
|
||||
gcode:
|
||||
# Use a default 1kHz tone if S is omitted.
|
||||
{% set S = params.S|default(1000)|int %}
|
||||
# Use a 10ms duration is P is omitted.
|
||||
{% set P = params.P|default(100)|int %}
|
||||
SET_PIN PIN=BEEPER_pin VALUE=0.5 CYCLE_TIME={ 1.0/S if S > 0 else 1 }
|
||||
G4 P{P}
|
||||
SET_PIN PIN=BEEPER_pin VALUE=0
|
||||
|
||||
|
||||
[gcode_macro TESTZ]
|
||||
description: Wykonuje 5-liniowy test do kalibracji offsetu Z
|
||||
gcode:
|
||||
{% set H_TEMP = 200 %} ; Temperatura hotendu w stopniach C
|
||||
{% set B_TEMP = 60 %} ; Temperatura stołu w stopniach C
|
||||
|
||||
M140 S{B_TEMP} ; Ustaw temperaturę stołu (bez czekania)
|
||||
M104 S{H_TEMP} ; Ustaw temperaturę hotendu (bez czekania)
|
||||
|
||||
G28 ; Homing wszystkich osi (X, Y, Z)
|
||||
|
||||
M190 S{B_TEMP} ; Czekaj, aż stół osiągnie temperaturę
|
||||
M109 S{H_TEMP} ; Czekaj, aż hotend osiągnie temperaturę
|
||||
|
||||
G92 E0 ; Zeruj ekstruder
|
||||
G1 Z0.2 F300 ; Podnieś dyszę na wysokość pierwszej warstwy (0.2mm)
|
||||
G1 X10 Y10 F6000 ; Przesuń głowicę do pozycji startowej (X10, Y10)
|
||||
|
||||
; Linia 1
|
||||
G1 E2 F1800 ; Wytłocz trochę filamentu, żeby wypełnić dyszę
|
||||
G1 X100 Y10 E10 F1200 ; Drukowanie linii (10-100 na X)
|
||||
G92 E0 ; Zeruj ekstruder
|
||||
G1 Z0.4 F300 ; Podnieś dyszę lekko w górę
|
||||
|
||||
; Linia 2
|
||||
G1 X10 Y20 F6000 ; Przesuń głowicę do startu drugiej linii
|
||||
G1 X100 Y20 E10 F1200 ; Drukowanie linii (10-100 na X)
|
||||
G92 E0 ; Zeruj ekstruder
|
||||
G1 Z0.6 F300 ; Podnieś dyszę lekko w górę
|
||||
|
||||
; Linia 3
|
||||
G1 X10 Y30 F6000 ; Przesuń głowicę do startu trzeciej linii
|
||||
G1 X100 Y30 E10 F1200 ; Drukowanie linii (10-100 na X)
|
||||
G92 E0 ; Zeruj ekstruder
|
||||
G1 Z0.8 F300 ; Podnieś dyszę lekko w górę
|
||||
|
||||
; Linia 4
|
||||
G1 X10 Y40 F6000 ; Przesuń głowicę do startu czwartej linii
|
||||
G1 X100 Y40 E10 F1200 ; Drukowanie linii (10-100 na X)
|
||||
G92 E0 ; Zeruj ekstruder
|
||||
G1 Z1.0 F300 ; Podnieś dyszę lekko w górę
|
||||
|
||||
; Linia 5
|
||||
G1 X10 Y50 F6000 ; Przesuń głowicę do startu piątej linii
|
||||
G1 X100 Y50 E10 F1200 ; Drukowanie linii (10-100 na X)
|
||||
G92 E0 ; Zeruj ekstruder
|
||||
|
||||
G1 Z10 F300 ; Podnieś dyszę znacznie
|
||||
G1 X0 Y0 F6000 ; Przesuń głowicę do pozycji startowej
|
||||
M104 S0 ; Wyłącz grzałkę hotendu
|
||||
M140 S0 ; Wyłącz grzałkę stołu
|
||||
M84 ; Wyłącz silniki
|
||||
|
||||
|
||||
#-------------------------------------
|
||||
# Printer Save Config
|
||||
#-------------------------------------
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 28.979
|
||||
#*# pid_ki = 1.558
|
||||
#*# pid_kd = 134.755
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 61.999
|
||||
#*# pid_ki = 0.771
|
||||
#*# pid_kd = 1246.178
|
||||
#*#
|
||||
#*# [bltouch]
|
||||
#*# z_offset = 1.640
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.260937, 0.331250, 0.293750, 0.339375, 0.309062
|
||||
#*# 0.272812, 0.325312, 0.237187, 0.263750, 0.274062
|
||||
#*# 0.260625, 0.322187, 0.228437, 0.263750, 0.255000
|
||||
#*# 0.238437, 0.295312, 0.228437, 0.263750, 0.242187
|
||||
#*# 0.234062, 0.338125, 0.334375, 0.365625, 0.314687
|
||||
#*# x_count = 5
|
||||
#*# y_count = 5
|
||||
#*# mesh_x_pps = 2
|
||||
#*# mesh_y_pps = 2
|
||||
#*# algo = lagrange
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 5.0
|
||||
#*# max_x = 310.0
|
||||
#*# min_y = 15.0
|
||||
#*# max_y = 337.0
|
||||
#*#
|
||||
#*# [input_shaper]
|
||||
#*# shaper_type_x = mzv
|
||||
#*# shaper_freq_x = 70.6
|
||||
#*# shaper_type_y = mzv
|
||||
#*# shaper_freq_y = 57.0
|
||||
Loading…
Reference in New Issue